共查询到20条相似文献，搜索用时 73 毫秒
1.
海底管道中颗粒侵蚀是油气输送过程面临的一个重要问题,也是流动保障的一个重要分支。弯头和T型堵头管是油气生产中最易于发生颗粒侵蚀的管道组件。首先使用剪切压力传输模型(SST)计算管道内流场,使用拉格朗日方法跟踪颗粒运动轨迹,结合颗粒随机反弹模型,建立跟踪复杂流场中大规模颗粒运动轨迹的一般方法;之后引入四种颗粒侵蚀公式,预测弯头、T型堵头管的砂粒侵蚀结果,并结合实验数据,比较分析各侵蚀公式的精度与适用性。分析结果表明,对于弯头,四种侵蚀公式的数值结果与实验结果均吻合良好,其中Tabakoff的侵蚀公式具有较高的精度和较好的适用范围;对于T型堵头管,数值方法对颗粒运动机理的模拟尚存缺陷,需做进一步改进。 相似文献
2.
以垂直悬臂提升管道为研究对象,应用有限元软件ADINA对其输送过程进行流固耦合效应特性分析。本文应用有限元软件ADINA对扬矿管道进行管内流体—管道—管外流体三者流固耦合模态分析。首先建立了扬矿管道流固耦合有限元模型,得到了不同输送矿石体积浓度、管道截面尺寸下的前6阶固有频率和振型,继而比较了上述条件下三者耦合、二者耦合及无耦合情况的固有频率,讨论了流固耦合作用对管道固有频率的影响。研究结果表明:(1)扬矿管道流固耦合效应下其固有频率随着管内输送矿石颗粒浓度的增大而降低,考虑管内流体—管道—管外流体三者流固耦合时的管道固有频率较只考虑管内流体—管道二者耦合和不考虑流固耦合时要小,影响系数也相应降低;(2)流体对管道流固耦合固有频率的影响程度随着相对厚度d值的增大而减小,在考虑管内流体—管道—管外流体三者流固耦合时管道固有频率较只考虑管内流体—管道二者耦合相对误差增大;(3)在实际的扬矿管道输送中应该考虑输送流体颗粒浓度、不同相对管道壁厚、管内流体—管道—管外流体三者流固耦合作用对固有频率的影响,尽量使管道固有频率远离工作频率,避免共振情况的发生分析结果对扬矿管道的动态响应计算、结构设计和减振研究具有一定的指导意义。 相似文献
3.
钢悬链线立管(SCR)与海床土体的接触问题对立管的疲劳寿命影响很大.运用ANSYS有限元软件中的接触单元模拟SCR与海床接触处的相互作用,考虑海床土体的非线性,建立SCR与海床系统有限元模型,并同已有的等价梁-弹簧模型进行了比较和验证.运用该模型进行计算分析,探讨了管道重量、土体模型和摩擦系数等对管道入土深度和弯矩的影响,为进一步研究SCR与海床的相互作用提供参考. 相似文献
4.
5.
6.
海底矿石在软管中的水力输送是深海采矿的重要过程。采用计算流体动力学—离散元耦合的计算方法（CFD-DEM）,对矿石颗粒在软管中的输送进行数值模拟,重点关注矿石颗粒的运动、分布规律以及管壁受到的颗粒作用力,分析输送速度和输送浓度（入射颗粒的体积分数）对输送过程的影响规律,探索管道中易发生堵塞、易受颗粒磨损的区域。结果表明,软管中颗粒的动力学特性与管道倾角、输送速度和输送浓度有关。颗粒主要沿管道截面底部推移,倾角较大的上升段出现处于悬移状态的颗粒;管道横截面内颗粒运动速度从上至下递减,截面中心处颗粒的速度接近输送速度。输送过程中颗粒的局部浓度（该区域颗粒与固液两相流的体积比）始终大于输送浓度,局部平均速度始终小于输送速度。上升段颗粒体积分数大于下降段,颗粒速度小于下降段。管道拱顶和谷底位置管壁所受颗粒作用力最明显,管壁最可能受颗粒磨损。 相似文献
7.
8.
铺设过程中海底管道的非线性分析 总被引：2，自引：1，他引：2
本文运用弹性杆理论建立了铺设过程中海底管道的综合相容的力学模型。该模型考虑了由于管道的大挠度变形引起的几何非线性和由于流体动载荷引的的载荷非线性的影响,考虑了随管道变形而变化的边界条件。介绍了差分法在求解该非线性模型中的应用,并对如何模拟边界条件提出了一整套方法。本数值方法的结果与已有的直接积分法计算结果比较,二者吻合较好。 相似文献
9.
通过物理模型试验研究水流作用下轴线倾斜海底管道的三维局部冲刷问题。利用超声波探头监测管道下部冲刷沿管轴线方向的扩展过程,分析海底管道三维局部冲刷的动态发展机理。由模型沙的冲蚀试验,建立沙床面剪切应力与泥沙表观侵蚀速率之间的关系式,并引入经验公式对沙床面剪切应力放大系数、泥沙表观侵蚀速率以及远场床面剪切应力之间的关系进行表达。由倾斜管道模型试验,在分析冲刷扩展位置随时间变化数据的基础上,结合上述经验公式以及沙床面剪切应力放大系数与管道埋深的关系,建立轴线倾斜海底管道冲刷扩展速率的预测公式。 相似文献
10.
卷管式铺管法在海管铺设中的应用愈发广泛,在铺设作业中管道会发生几何非线性变形,导致出现复杂的力学性能变化。针对管道在上卷、退卷过程中的屈服变化过程,通过弹塑性理论进行分析,推导出管道退卷后残余轴向应力的解析解;随后利用有限元软件ABAQUS建立模型实例,对比解析解与有限元模型,两者的计算结果基本吻合。基于上述有限元模型,研究上卷时的张力和退卷时的后张力对椭圆度、截面轴向应力和剪切应力的影响,并进行敏感性分析。模拟结果表明张力和后张力变化会影响管道截面的变形程度,退卷后截面上残余的轴向应力远高于剪切应力,并且通过敏感性分析,得到了残余椭圆度、残余应力随张力和后张力变化的规律。研究可为卷管铺设过程中张力和后张力的选择提供参考和借鉴。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
19.
20.
《海洋学报(英文版)》2014,(11):161-F0003
<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology, 相似文献