Experiments on liquid immiscibility in silicate melts with H2O, P, S, F and Cl: implications for natural magmas     

G. W. Lester  A. H. Clark  T. K. Kyser  H. R. Naslund 《Contributions to Mineralogy and Petrology》2013,166(1):329-349

Isobaric (200 MPa) experiments have been performed to investigate the effects of H₂O alone or in combination with P, S, F or Cl on liquid-phase separation in melts in the systems Fe₂SiO₄–Fe₃O₄–KAlSi₂O₆–SiO₂, Fe₃O₄–KAlSi₂O₆–SiO₂ and Fe₃O₄–Fe₂O₃–KAlSi₂O₆–SiO₂ with or without plagioclase (An₅₀). Experiments were heated in a rapid-quench internally heated pressure vessel at 1,075, 1,150 or 1,200 °C for 2 h. Experimental fO₂ was maintained at QFM, NNO or MH oxygen buffers. H₂O alone or in combination with P, S or F increases the temperature and composition range of two-liquid fields at fO₂ = NNO and MH buffers. P, S, F and Cl partition preferentially into the Fe-rich immiscible liquid. Two-liquid partition coefficients for Fe, Si, P and S correlate well with the degree of polymerization of the SiO₂-rich liquid and plot on similar but distinct power-law curves compared with equivalent anhydrous or basaltic melts. The addition of 2 wt% S to the system Fe₃O₄–Fe₂O₃–KAlSi₂O₆–SiO₂ stabilizes three immiscible melts with Fe-, FeS- and Si-rich compositions. H₂O-induced suppression of liquidus temperatures in the experimental systems, considered with the effects of pressure on the temperature and composition ranges of two-liquid fields in silicate melts, suggests that liquid-phase separation may be stable in some H₂O-rich silicate magmas at pressures in excess of 200 MPa.  相似文献   

The effects of K2O on the compositions of near-solidus melts of garnet peridotite at 3 GPa and the origin of basalts from enriched mantle     

Fred A. Davis  Marc M. Hirschmann 《Contributions to Mineralogy and Petrology》2013,166(4):1029-1046

Enrichment in K₂O in oceanic island basalts (OIB) is correlated with high SiO₂, low CaO/Al₂O₃, and radiogenic isotopic signatures indicative of enriched mantle sources (EM1 and EM2). These are also chemical characteristics of the petit-spot lavas, which are highly enriched in K₂O (3–4 wt%) compared to other primitive oceanic basalts. We present experimentally derived liquids with varying concentrations of K₂O in equilibrium with a garnet lherzolite residue at 3 GPa to test the hypothesis that the major element characteristics of EM-type basalts are related to their enrichment in K₂O. SiO₂ is known to increase with K₂O at pressures less than 3 GPa, but it was previously unknown if this effect was significant at the high pressures associated with partial melting at the base of the lithosphere. We find that at 3 GPa for each 1 wt% increase in the K₂O content of a garnet lherzolite saturated melt, SiO₂ increases by ~0.5 wt% and CaO decreases by ~0.5 wt%. MgO and $K_{D}^{{{\text{Fe}} - {\text{Mg}}}}$ K D Fe - Mg each decrease slightly with K₂O concentration, as do Na₂O and Cr₂O₃. The effect of K₂O alone is not strong enough to account for the SiO₂ and CaO signatures associated with high-K₂O OIB. The SiO₂, CaO, and K₂O concentrations of experimentally derived partial melts presented here resemble those of petit-spot lavas, but the Al₂O₃ concentrations from the experimental melts are greater. Partitioning of K₂O between peridotite and melt suggests that petit spots, previously considered to sample ambient asthenosphere, require a source more enriched in K₂O than the MORB source.  相似文献   

The effect of phosphorus on the iron redox ratio,viscosity, and density of an evolved ferro-basalt   总被引：1，自引：1，他引：1  

M. J. Toplis  D. B. Dingwell  G. Libourel 《Contributions to Mineralogy and Petrology》1994,117(3):293-304

Despite the abundant evidence for the enrichment of phosphorus during the petrogenesis of natural ferro-basalts, the effect of phosphorus on the physical properties of these melts is poorly understood. The effects of phosphorus on the viscosity, density and redox ratio of a ferro-basaltic melt have been determined experimentally. The viscosity measurements were obtained using the concentric cylinder method on a ferro-basaltic melt above its liquidus, at 1 atm, in equilibrium with air and with CO₂. The density measurements were performed using the double Pt-bob Archimedean method at superliquidus conditions under 1 atm of air. The redox ratio was obtained by wet chemical analysis of samples collected during physical property measurements. Phosphorus pentoxide reduces ferric iron in ferro-basaltic melt. The reduction due to P₂O₅ is much larger than that for most other oxide components in basaltic melts. A coefficient for the reduction of ferric iron has been generated for inclusion in calculation schemes. The effect of P₂O₅ on the viscosity is shown to be complex. The initial reduction of ferric iron with the addition of P₂O₅ results in a relatively small change in viscosity, while further addition of P₂O₅ results in a strong increase. The addition of phosphorus to a ferro-basaltic melt also reduces the density. A partial molar volume of 64.5±0.7 cm³/mol for P₂O₅ in this melt has been obtained at 1300° C, yielding a volume of 12.9 cm³/mol per oxygen, consistent with a tetrahedral coordination for this high field strength cation. The effects of P₂O₅ on redox state, density and viscosity provide constraints on the structural role of phosphorus in these melts. The results suggest a complex interaction of phosphorus with the aluminosilicate network, and tetrahedral ferric iron. In light of the significant effects of phosphorus on the physical and chemical properties of ferro-basaltic liquids, and the extreme enrichments possible in these liquids in nature, the role of phosphorus in these melts should, in future, be considered more carefully.  相似文献   

The stability of sapphirine + quartz: calculated phase equilibria in FeO–MgO–Al2O3–SiO2–TiO2–O     

K. TAYLOR‐JONES  R. POWELL 《Journal of Metamorphic Geology》2010,28(6):615-633

The presence in rocks of coexisting sapphirine + quartz has been widely used to diagnose conditions of ultra‐high‐temperature (UHT) metamorphism (>900 °C), an inference based on the restriction of this assemblage to temperatures >980 °C in the conventionally considered FeO–MgO–Al₂O₃–SiO₂ (FMAS) chemical system. With a new thermodynamic model for sapphirine that includes Fe₂O₃, phase equilibra modelling using thermocalc software has been undertaken in the FeO–MgO–Al₂O₃–SiO₂–O (FMASO) and FeO–MgO–Al₂O₃–SiO₂– TiO₂–O (FMASTO) chemical systems. Using a variety of calculated phase diagrams for quartz‐saturated systems, the effects of Fe₂O₃ and TiO₂ on FMAS phase relations are shown to be considerable. Importantly, the stability field of sapphirine + quartz assemblages extends down temperature to 850 °C in oxidized systems and thus out of the UHT range.  相似文献   

The role of phosphorus in rhyolitic liquids as determined from the homogeneous iron redox equilibrium   总被引：1，自引：1，他引：1  

Rosa Gwinn  Paul C. Hess 《Contributions to Mineralogy and Petrology》1993,113(3):424-435

The redox ratio of iron is used as an indicator of solution properties of silicate liquids in the system (SiO–Al₂O₃–K₂O–FeO–Fe₂O₃–P₂O₅). Glasses containing 80–85 mol% SiO₂ with 1 mol% Fe₂O₃ and compositions covering a range of K₂O/Al₂O₃ were synthesized at 1400°C in air (fixed fO₂). Variations in the ratio FeO/FeO_1.5 resulting from the addition of P₂O₅ are used to determine the solution behavior of phosphorus and its interactions with other cations in the silicate melt. In 80 mol% SiO₂ peralkaline melts the redox ratio, expressed as FeO/FeO_1.5, is unchanged relative to the reference curve with the addition of 3 mol% P₂O₅. Yet, the iron redox ratio in the 85 mol% SiO₂ potassium aluminosilicate melts is decreased relative to phosphorus-free liquids even for small amounts of P₂O₅ (0.5 mol%). The redox ratio in peraluminous melts is decreased relative to phosphorus- free liquids at P₂O₅ concentrations of 3 mol%. In peraluminous liquids, complexing of both Fe⁺³–O–P⁺⁵ and Al⁺³–O–P⁺⁵ occur. The activity coefficient of Fe⁺³ is decreased because more ferric iron can be accommodated than in phosphorus-free liquids. In peralkaline melts, there is no evidence that P⁺⁵ is removing K⁺ from either Al⁺³ or Fe⁺³ species. In chargebalanced melts with 3 mol% Fe₂O₃ and very high P₂O₅ concentrations, phosphorus removes K⁺ from K–O–Fe⁺³ complexes resulting in a redox increase. P₂O₅ should be accommodated easily in peraluminous rhyolitic liquids and phosphate saturation may be suppressed relative to metaluminous rhyolites. In peralkaline melts, phosphate solubility may increase as a result of phosphorus complexing with alkalis. The complexing stoichiometry may be variable, however, and the relative influence of peralkalinity versus temperature on phosphate solubility in rhyolitic melts deserves greater attention.  相似文献   

Model systems for anatexis of pelitic rocks     

Alan Bruce Thompson  John R. Algor 《Contributions to Mineralogy and Petrology》1977,63(3):247-269

A consistent arrangement of solidus curves for reactions involving white mica, alkali feldspar, Al₂SiO₅, quartz and H₂O, as expressed by the components KAlO₂-NaAlO₂-Al₂O₃-SiO₂-H₂O, provides a generally accurate and useful model for the origin of migmatites and peraluminous granites through partial melting of pelitic rocks. The complexities of the univariant (Na-K) reactions may be easily seen on the projection from SiO₂ and H₂O onto the Ab-Or-Al₂O₃ plane. Alternative topologies for the appearance of muscovite, paragonite and Al₂SiO₅ on the quartz and H₂O-saturated liquidus may be eliminated by a consideration of possible compositions of liquid and solid phases and Schreinemakers' analysis around (Na-K) invariant points. Paragonite is not likely to be an important phase on the liquidus for most melting paths. Melting paths for natural assemblages may be easily constructed appropriate to P-T-aH₂O paths in the model system. Such paths are consistent with observed textures in natural assemblages. Although general models can be developed for decreased aH₂O, it is difficult to separate such effects from those involving participation of a calcic component without careful examination of natural assemblages and experimental calibration of appropriate reactions.  相似文献   

The combined effects of chlorine and fluorine on the viscosity of aluminosilicate melts   总被引：1，自引：0，他引：1  

Milada Zimova 《Geochimica et cosmochimica acta》2007,71(6):1553-1562

The effect of fluorine and fluorine + chlorine on melt viscosities in the system Na₂O-Fe₂O₃-Al₂O₃-SiO₂ has been investigated. Shear viscosities of melts ranging in composition from peraluminous [(Na₂O + FeO) < (Al₂O₃ + Fe₂O₃)] to peralkaline [(Na₂O + FeO) > (Al₂O₃ + Fe₂O₃)] were determined over a temperature range 560-890 °C at room pressure in a nitrogen atmosphere. Viscosities were determined using the micropenetration technique in the range of 10^8.8 to 10^12.0 Pa s. The compositions are based on addition of FeF₃ and FeCl₃ to aluminosilicate melts with a fixed amount of SiO₂ (67 mol%). Although there was a significant loss of F and Cl during glass syntheses, none occurred during the viscometry experiments. The presence of fluorine causes a decrease in the viscosity of all melts investigated. This is in agreement with the structural model that two fluorines replace one oxygen; resulting in a depolymerisation of the melt and thus a decrease in viscosity. The presence of both chlorine and fluorine results in a slight increase in the viscosity of peraluminous melts and a decrease in viscosity of peralkaline melts. The variation in viscosity produced by the addition of both fluorine and chlorine is the opposite to that observed in the same composition melts, with the addition of chlorine alone (Zimova M. and Webb S.L. (2006) The effect of chlorine on the viscosity of Na₂O-Fe₂O₃-Al₂O₃-SiO₂ melts. Am. Mineral.91, 344-352). This suggests that the structural interaction of chlorine and fluorine is not linear and the rheology of magmas containing both volatiles is more complex than previously assumed.  相似文献   

Solution behavior of C-O-H volatiles in FeO-Na2O-Al2O3-SiO2 melts in equilibrium with liquid iron alloy and graphite at 4 GPa and 1550°C     

A. A. Kadik  V. V. Koltashev  E. B. Kryukova  V. G. Plotnichenko  T. I. Tsekhonya  N. N. Kononkova 《Geochemistry International》2014,52(9):707-725

In order to elucidate the solution behavior of carbon and hydrogen in iron-bearing magmatic melts in equilibrium with a metallic iron phase and graphite at oxygen fugacity (fO₂) values 2–5 orders of magnitude below the iron-wustite buffer equilibrium, fO₂ (IW), experiments were carried out at 4 GPa and 1550°C with melts of FeO-Na₂O-SiO₂-Al₂O₃ compositions. Melt reduction in response to an fO₂ decrease was accompanied by a decrease in FeO content. The values of fO₂ in the experiments were determined on the basis of equilibrium between Fe-C-Si alloy and silicate liquid. Infrared and Raman spectroscopy showed that carbon compounds are formed in FeO-Na₂O-SiO₂-Al₂O₃ melts: CH₄ molecules, CH₃ complexes (Si-O-CH₃), and complexes with double C=O bonds. The content of CO₂ molecules and carbonate ions (CO ₃ ^2? ) is very low. In addition to carbon-bearing compounds, dissolved hydrogen occurs in melt as H₂ and H₂O molecules and OH^? groups. The spectral characteristics of FeO-Na₂O-SiO₂-Al₂O₃ glasses indicate the occurrence of redox reactions in the melt, which are accompanied at decreasing fO₂ by a significant decrease in H₂O and OH^?, a slight decrease in H₂, and a significant concomitant increase in CH₄ content. The content of species with the double C=O bond increases considerably at decreasing fO₂ and reaches a maximum at ΔlogfO₂(IW) = ?3. According to the obtained IR spectra, the total water content (OH^? + H₂O) in the glasses is 1.2–5.8 wt % and decreases with decreasing fO₂. The high H₂O contents are due largely to oxygen release related to FeO reduction in the melt. The total carbon content at high H₂O (4.9–5.8 wt %) is approximately 0.4 wt %. The carbon content in liquid iron alloys depends on silicon content and, probably, oxygen solubility and ranges from 0.3 to 3.65 wt %. Low carbon contents were observed at a significant increase in Si content in liquid iron alloy, which may be as high as ～13 wt % at fO₂ values 4–5 orders of magnitude below fO₂(IW).  相似文献   

Forsterite-diopside-spinel-liquid equilibria in the system CaO−MgO−Al2O3−SiO2 at 20 kbar and petrological applications     

Biswajit Mukhopadhyay 《Contributions to Mineralogy and Petrology》1991,106(2):253-264

Liquidus phase relationships in the CaAlAl–SiO₆–Mg₂SiO₄–CaMgSi₂O₆–CaAlSi₂O₈ portion of the simplified basalt tetrahedron in the CaO–MgO–SiO₂–Al₂O₃ system have been experimentally determined at 20 kbar pressure. The fo+di _ss+sp+li univariant curve, that pierces the fo-di-an join and meets the fo+di _ss+ en_ss+sp+li invariant point in the basalt tetrahedron, extends all the way to and pierces the di-fo-CaTs join, the limit of the simplified basalt tetrahedron toward the silica undersaturated portion.An algebraic method, relying on compositions of two successive liquids on a univariant curve and those of the crystalline phases in equilibrium with the respective liquids, is developed to identify the type of reaction that takes place along an isobarically univariant curve and to detect whether there is a temperature maximum on that curve. Use of this method for the di _ss+fo+sp+li univariant equilibria shows that a temperature maximum exists on this curve at the composition Fo₁₁Di₅₆An₃CaTs₃₀, very close to and slighthly to the SiO₂-rich side of the fo-di-CaTs join. The temperature along the univariant curve continuously decreases from the temperature maximum (1500°C) to the invariant point (1475°C) where the univariant curve is terminated by the appearance of e _ss as a member of the equilibrium assemblage. Along this part of the curve, a reaction relationship occurs according to the equation fo+li=di _ss+ sp. Compositions of di _ss in equilibrium with the liquids from the temperature maximum to the fo+di _ss+en_ss+ sp+li invariant point range from Di₆₆En₉CaTs₂₅ to Di₃₆En₄₀CaTs₂₄. Because of the reaction relationship of forsterite with liquid, fractional crystallization of a model alkalic basaltic liquid would cause liquids to move off the fo-di _ss-sp-li univariant curve onto the sp-di _ss divariant surface. Crystallization of di _ss and sp would then lead to silica enrichment of residual liquids. Thus at pressures below 30 kbar, at which pressure the Al₂O₃–CaSiO₃–MgSiO₃ plane becomes a new thermal divide cutting through both the tholeiitic and alkalic volumes, alkalic liquids will fractionate toward tholeiitic compositions without crossing a thermal divide. This relationship would be expected to persist at pressures down to about 4 kbar where a maximum on the fo-di-an-li boundary line causes a thermal divide near the fo-di-an plane. Strongly SiO₂-undersaturated liquids (e.g. nephelinites, basanites), on the other hand, cannot be derived from SiO₂-undersaturated basalts (e.g. alkali olivine basalt) by fractional crystallization at 20 kbar. We also found that no gt primary phase volume cuts the wo-en-Al₂O₃ join at 20 kbar pressure. The wehrlite, the olivine clinopyroxenite, and the Al-augite group lherzolite xenoliths, containing highly aluminous clinopyroxenes (enriched in Ca-Tschermak), can be interpreted as crystal cumulates from alkalic basalts in the light of this experimental study. This is consistent with the mode of origin of these xenoliths proposed from petrographic, mineralogic, and geochemical studies.Abbreviations and notations di CaMgSi₂O₆ - fo Mg₂SiO₄ - an CaAl₂Si₂O₈ - CaTs CaAlAlSiO₆ - sp MgAl₂O₄ - en MgSiO₃ - wo CaSiO₃ - gt Ca₃Al₂Si₃O₁₂–Mg₃Al₂Si₃O₁₂ - qz SiO₂ - li Liquid - gl glass - ss Solid Solution - A An mxn matrix - X A column vector - kbar kilobar  相似文献   

Glass transitions and thermodynamic properties of amorphous SiO2, NaAlSinO2n+2 and KAlSi3O8     

Pascal Richet  Yan Bottinga 《Geochimica et cosmochimica acta》1984,48(3):453-470

A drop calorimetric study, between 900 and 1800 K, of amorphous SiO₂, NaAlSi₃O₈, NaAlSi₂O₆, NaAlSiO₄ and KAlSi₃O₈ shows the increase in heat capacity which results from glass transitions. For these glasses, the fictive temperature has a negligible effect on the heat capacity above room temperature, but it has an important influence on the enthalpy of formation as obtained from solution calorimetry. From these results and published Cp and enthalpy of solution data, several properties have been calculated: the enthalpies of fusion of high albite, nepheline, Jadeite and high sanidine, the thermodynamic functions of amorphous NaAlSi₃O₈ and KAlSi₃O₈ between 0 and 2000 K, and some mixing properties of liquids along the join SiO₂-NaAlSi₃O₈. The latter data suggest that these liquids behave more closely as athermal solutions than as regular solutions.  相似文献