共查询到18条相似文献，搜索用时 171 毫秒
1.
2.
3.
4.
在地铁、高速铁路等基础设施的快速发展下,长期滞弹性微损伤累积效应应引起人们的关注,尤其是对动载和高频效应的关注.本文在频率0.01～1000 Hz、温度-50～200℃内研究了弹性范围内的饱和砂岩、大理岩,在强迫共振、单轴循环加载下的温度和频率的滞弹性行为的弛豫衰减峰.结果显示,弹性模量和波速随温度的升高而下降,且下降梯度比一般岩石的力学实验结果要陡;随着频率提高,弹性模量和波速显著增大,频散效应会加强.该结果反映了在应力诱导下岩石内部微缺陷等微损伤之间的运动和相互作用的微观过程,该过程会导致微结构变化,进而引起微观的位移,产生微损伤;微损伤经历一段时间或很长时间的积累过程,就可能造成疲劳损伤断裂.岩石内部微观结构的非均匀性和矿物晶粒间界等缺陷是最薄弱的部位,在循环应力作用下再次形成新的微裂纹系统,从而加速损伤的积累,引起断裂.除此之外,岩石中多种渠道的残余应力会导致疲劳损伤;振动频率的提高,也会加速岩石的损伤;结合温度升高的综合效应会引起岩石内部微裂纹增长,导致岩石微结构变化并引起微损伤,虽然这是在屈服点以下引发的滞弹性微损伤,但最终它们都将使岩石的品质劣化. 相似文献
5.
岩石内部磁场梯度对核磁共振测井横向弛豫T2分布有较大的影响.本文提出了一种利用自旋回波脉冲序列探测岩石内部磁场梯度的二维核磁共振方法,发展了相应的反演方法,得到了含顺磁性物质的饱和水砂岩和泥质砂岩的内部磁场梯度分布规律.结果表明,随顺磁物质含量的增加,岩石内部磁场梯度增大.含顺磁物质的饱和水砂岩颗粒均匀,不含粘土矿物,内部磁场梯度呈单峰分布特征.含绿泥石粘土矿物的饱和水泥质砂岩,T2分布呈双峰特征,束缚水峰明显,小孔短T2对应的梯度值大于大孔长T2对应的梯度值.当绿泥石含量小于15%时,随绿泥石含量的增加,对应束缚水峰的短T2组分明显增多,T2分布展宽;当绿泥石含量大于15%以后,较大的岩石内部磁场梯度使短弛豫信息衰减迅速,表现出随绿泥石含量的增加,短T2组分减少,T2分布变窄. 相似文献
6.
本文旨在研究多孔岩石声衰减机制及衰减和频率的关系,用共振法测量了人工多孔材料10~5Hz以下的弯曲振动能量损耗,发展了前人测量弹性模量的方法.实验结果表明:干燥试样的内耗基本上与频率无关:水饱和试样的内耗比干燥试样的大得多,并在24.0kHz有显著的弛豫峰;饱和试样的内耗主要产生于固体骨架与孔隙流体之间的相对运动.实验结果与Riot理论和局部流体流动机制一致,但未看到Dunn预言的“边界效应”. 相似文献
7.
8.
在MTS伺服压机上对不同饱和状态的砂岩、大理岩标本进行了垂直层理和平行层理两个方向的正弦波加载试验,研究了饱和岩石的各向异性及非线性黏弹性行为. 在最大载荷低于岩石的屈服点时,获得的衰减、杨氏模量、泊松比、波速都表现出显著的各向异性,同时它们还具有较明显的应变振幅效应和频率效应. 随着应变振幅的增大,衰减近似呈线性增长,杨氏模量和泊松比近似呈线性下降. 在0.005-4Hz频段内除衰减不明显依赖频率以外,杨氏模量、泊松比、波速对频率的依赖性都较强; 当频段扩大到15Hz时,这4个参数都表现出较强的频率效应. 饱和岩石的衰减、杨氏模量、泊松比、波速均随饱和液体的黏滞系数增大而增大. 相似文献
9.
本文运用随机游走方法模拟了砂岩储层中流体的核磁共振(NMR)响应及其受限扩散现象.通过改变数字岩心的分辨率模拟生成不同孔隙尺寸的砂岩,研究了不同孔隙尺寸砂岩饱含水时流体扩散系数随扩散时间的变化关系,同时模拟了砂岩饱和单相流体和两相流体的NMR响应;研究了流体的受限扩散系数与横向弛豫时间T2的关系,分析了表面弛豫率和胶结指数对润湿相流体受限扩散系数线位置的影响,并将其用于解释砂岩储层的D-T2分布.结果表明:孔隙流体的扩散系数会随扩散时间的增加而逐渐减小并趋于定值.随着岩石孔隙尺寸的减小,受限扩散现象越明显,受限扩散对岩石NMR响应的影响也越大.润湿相流体受限扩散系数线的位置受岩石胶结指数和表面弛豫率的影响较大.由于润湿相流体扩散系数减小,导致D-T2分布中润湿相流体信号偏离其自由扩散系数线,需要利用流体的受限扩散系数线准确识别D-T2分布中的润湿相流体. 相似文献
10.
致密砂岩普遍具有低孔、低渗及微裂缝发育的地质特征,并且呈现出很强的非均匀性.致密砂岩储层与常规砂岩储层比较,具有明显的岩石物理性质、渗流力学性质方面的差异.致密砂岩内部的非均匀性对弹性波频散、衰减有显著影响,其中包括孔隙结构的非均匀性,即岩石内部孔隙参数的不均一性,以及孔隙内部不相混溶流体的非均匀分布;此外,非均匀性的尺度也决定了波出现显著频散与衰减的频段.综合考虑致密砂岩孔隙结构非均匀性及流体斑块状饱和的非均匀性,本文采用双双重孔隙介质结构模拟了致密砂岩的弹性波响应,分析了同时具备两类非均质性岩石中的波传播特征.调查分析了两组分别来自中国鄂尔多斯盆地苏里格气田及四川盆地广安气田的不同类型致密砂岩储层的岩芯超声波实验数据,给出了岩石样本的弹性波速度频散与衰减曲线.结果显示理论模型预测结果与完全饱和、部分饱和岩石的实验数据吻合良好.对两个地区致密砂岩岩芯数据进行对比分析,苏里格致密砂岩样本总体上比广安致密砂岩渗透率高,在各孔隙度范围内,特征模拟显示苏里格样本的裂隙尺寸明显大于广安样本.广安致密砂岩在低孔隙度范围内发育了更多、更小的颗粒裂隙/接触.致密砂岩的速度频散与衰减结果受流体黏度、晶体破裂及流体斑块状饱和的共同影响.此外,孔隙度越大,部分饱和岩石中斑块状饱和机制对总衰减的贡献越低,与之相对,结构非均质性所占的比重则有所增强. 相似文献
11.
12.
通过对饱和砂岩和大理岩的循环荷载实验,分析了饱和岩石在循环荷载下的应力-应变滞后回线、瞬时杨氏模量、泊松比的“X”形变化曲线,以及杨氏模量随应变振幅的增加而减少等滞后现象,并分析了施加外力的应变振幅对衰减的影响,认为岩石在循环荷载作用下的衰减与应变振幅成正比,提出的衰减b值反映了岩石在循环荷载作用下衰减的程度. 岩石的衰减和滞后存在密切的关系,通过饱和岩石的宏观行为,探讨了饱和岩石在循环荷载下的滞后和衰减现象的微观机理,认为孔隙流体流动在岩石的滞后和衰减中起着重要作用,岩石内部的颗粒接触粘合和黏滑摩擦可能是孔隙岩石在循环荷载作用下产生滞后和衰减的原因. 相似文献
13.
根据脉冲传播和频谱比方法的基本原理建立了一套超声波衰减和波速测量系统。研究了单轴压缩下超声P波在干燥和饱水的小浪底砂岩和房山大理岩中的衰减和速度。常压下,水饱和样品的Q_P值低于干燥样品。初始加载时,在大多数情况下,Q_p值明显增加即衰减减小;当应力水平达破裂强度50-60％后,岩石开始膨胀,Q_p减小即衰减增加;临近破裂Q_p减至最小。Q_p的变化量达一个数量级。单轴压缩下,在干燥和饱水的砂岩、大理岩中,V_p分别增加为27％和28％,44％和11％。径向Q_p和V_p随单轴压力的变化比轴向小得多,呈现明显各向异性。在本实验条件下,波在裂纹表面的摩擦耗散是主要的衰减机制,水的作用主要是潮湿和润滑裂纹表面,促进滑动,增加衰减。 相似文献
14.
Ismael Himar Falcon-Suarez Kelvin Amalokwu Jordi Delgado-Martin Ben Callow Katleen Robert Laurence North Sourav K. Sahoo Angus I. Best 《Geophysical Prospecting》2019,67(4):784-803
Synthetic rock samples can offer advantages over natural rock samples when used for laboratory rock physical properties studies, provided their success as natural analogues is well understood. The ability of synthetic rocks to mimic the natural stress dependency of elastic wave, electrical and fluid transport properties is of primary interest. Hence, we compare a consistent set of laboratory multi-physics measurements obtained on four quartz sandstone samples (porosity range 20–25%) comprising two synthetic and two natural (Berea and Corvio) samples, the latter used extensively as standards in rock physics research. We measured simultaneously ultrasonic (P- and S-wave) velocity and attenuation, electrical resistivity, permeability and axial and radial strains over a wide range of differential pressure (confining stress 15–50 MPa; pore pressure 5–10 MPa) on the four brine saturated samples. Despite some obvious physical discrepancies caused by the synthetic manufacturing process, such as silica cementation and anisotropy, the results show only small differences in stress dependency between the synthetic and natural sandstones for all measured parameters. Stress dependency analysis of the dry samples using an isotropic effective medium model of spheroidal pores and penny-shaped cracks, together with a granular cohesion model, provide evidence of crack closure mechanisms in the natural sandstones, seen to a much lesser extent in the synthetic sandstones. The smaller grain size, greater cement content, and cementation under oedometric conditions particularly affect the fluid transport properties of the synthetic sandstones, resulting in lower permeability and higher electrical resistivity for a similar porosity. The effective stress coefficients, determined for each parameter, are in agreement with data reported in the literature. Our results for the particular synthetic materials that were tested suggest that synthetic sandstones can serve as good proxies for natural sandstones for studies of elastic and mechanical properties, but should be used with care for transport properties studies. 相似文献
15.
Laboratory data on dry and saturated rocks show that pore fluid has the most important effect on rock attenuation. It is known
that viscous and inertial coupling between the frame of a porous rock and its pore fluid dissipates seismic energy by conversion
to heat and hence cause attenuation. We show that attenuation peaks, in saturated rock have the same property as that of typical
thermally activated relaxations. In the frequency domain, a plot of attenuation versus frequency shows an obvious systematic
shift to higher frequencies with increasing temperatures. Similarly, the attenuation versus temperature curve moves to higher
temperature with increasing frequencies. The attenuation peaks are somewhat broader than that for a Zener relaxation. A Cole-Cole
distribution of relaxation times closely matches the attenuations. This behavior can be explained theoretically by local flow
mechanisms. 相似文献
16.
The attenuation of stress waves in fluid saturated porous rock 总被引：5，自引：0，他引：5
ＴｈｅａｔｅｎｕａｔｉｏｎｏｆｓｔｒｅｓｗａｖｅｓｉｎｆｌｕｉｄｓａｔｕｒａｔｅｄｐｏｒｏｕｓｒｏｃｋＤＡＯＹＩＮＧＸＩ（席道瑛）ＪＩＮＧＹＩＣＨＥＮＧ（程经毅）ＬＩＡＮＧＫＵＮＹＩ（易良坤）ＢＩＮＺＨＡＮＧ（张斌）Ｄｅｐａｒｔｍｅｎｔｏｆ... 相似文献
17.
The aim of this study was to investigate the effects of supercritical CO2 (scCO2) injection on the elastic and anelastic properties of sandstone at seismic and ultrasonic frequencies. We present the results of the low‐frequency and ultrasonic experiments conducted on water‐saturated sandstone (Donnybrook, Western Australia) flooded with scCO2. The sandstone was cut in the direction perpendicular to a formation bedding plane and tested in a Hoek triaxial pressure cell. During the experiments with scCO2, the low‐frequency and ultrasonic systems and the pump dispensing scCO2 were held at a temperature of 42°C. The elastic parameters obtained for the sandstone with scCO2 at seismic (0.1 Hz–100 Hz) and ultrasonic (～0.5 MHz) frequencies are very close to those for the dry rock. The extensional attenuation was also measured at seismic frequencies for the dry, water‐saturated, and scCO2‐injected sandstones. The applicability of Gassmann's fluid substitution theory to obtained results was also tested during the experiments. 相似文献
18.
Computer simulations are used to calculate the elastic properties of model cemented sandstones composed of two or more mineral phases. Two idealized models are considered – a grain‐overlap clay/quartz mix and a pore‐lining clay/quartz mix. Unlike experimental data, the numerical data exhibit little noise yet cover a wide range of quartz/cement ratios and porosities. The results of the computations are in good agreement with experimental data for clay‐bearing consolidated sandstones. The effective modulus of solid mineral mixtures is found to be relatively insensitive to microstructural detail. It is shown that the Hashin–Shtrikman average is a good estimate for the modulus of the solid mineral mixtures. The distribution of the cement phase is found to have little effect on the computed modulus–porosity relationships. Numerical data for dry and saturated states confirm that Gassmann's equations remain valid for porous materials composed of multiple solid constituents. As noted previously, the Krief relationship successfully describes the porosity dependence of the dry shear modulus, and a recent empirical relationship provides a good estimate for the dry‐rock Poisson's ratio. From the numerical computations, a new empirical model, which requires only a knowledge of system mineralogy, is proposed for the modulus–porosity relationship of isotropic dry or fluid‐saturated porous materials composed of multiple solid constituents. Comparisons with experimental data for clean and shaly sandstones and computations for more complex, three‐mineral (quartz/dolomite/clay) systems show good agreement with the proposed model over a very wide range of porosities. 相似文献