共查询到20条相似文献，搜索用时 15 毫秒
1.
The energy saving performance of contra-rotating azimuth propulsor (CRAP) is investigated based on low order potential-based panel method. The hydrodynamic interactions among the forward propeller (FP), rear propeller (RP) and the pod unit (PU) which includes the pod body and the strut are considered through induced velocities which are obtained by panel method. In order to have a better understanding about the energy saving performance of CRAP, the hydrodynamic performance of a conventional propeller (CP) supplying the same thrust with CRAP at design condition is also calculated. At design condition, CRAP has a decrease in delivered power by approximately 8% comparing with CP, and the tangential induced velocities in slipstream show that CRAP recovers the rotational energy of slipstream effectively. At off-design conditions, the rotational speed of CRAP is adjusted to supply the same thrust with CP. In general, the delivered power of CRAP is significantly smaller than that of CP, and the energy saving performance of CRAP increases with the decrease of inflow velocity. 相似文献
2.
The propulsive efficiency maximization of contra-rotating azimuth propulsor (CRAP) at model scale is investigated through searching the optimal matching rotational speeds of the forward propeller (FP) and rear propeller (RP) of CRAP based on the potential-based panel method. The hydrodynamic performance of CRAP with changing rotational speeds (FP and RP may have different rotational speeds) are calculated. When the inflow velocity is certain, the cubic spline interpolation method is used to get the equal thrust points at which CRAP has the same thrust with the corresponding conventional propeller (CP). Then, the delivered powers at these equal thrust points are further obtained through cubic spline interpolation method. The rotational speeds of FP and RP at the equal thrust point corresponding to the minimal delivered power are the optimal matching rotational speeds of CRAP. The optimal matching calculations are carried out at different inflow velocities. The results of the optimal matching investigation show that CRAP has the lowest delivered powers when FP and RP have the optimal matching rotational speeds and that the energy saving level decreases with the increase of inflow velocity. The optimal matching rotational speed ratio decreases with the increase of inflow velocity. In general, the delivered powers of CRAP having optimal matching rotational speeds at different inflow velocities are obviously smaller than those of CP. 相似文献
3.
This paper provides an overview of a bioinspired delay stall propulsor (BDSP) concept that employs delayed stall unsteady lift enhancement to increase the lift on propeller blades without adding any complexity to the propulsor. This BDSP concept can provide greatly increased propeller thrust for a given propeller diameter, leading to both increased speed and/or maneuverability. Alternately, this technology offers reduced radiated noise while maintaining current thrust levels through reduction in both propulsor rotation speed and acoustic cancellation. Preliminary two-dimensional simulations have shown a potential 36% reduction in rotational speed at constant thrust, leading to an estimated 4-dB reduction in the total radiated acoustic power. It is believed that the BDSP concept will be simple to manufacture, rugged, and easy to retrofit into existing marine propulsors. This technology has direct application to torpedoes, unmanned underwater vehicles, maneuvering thrusters, submarines, and other propeller-driven devices. 相似文献
4.
The performance of the contra-rotating Wells turbine installed in the LIMPET wave power station is compared to the predicted performance from theoretical analysis and model tests. A reasonable agreement was found between the predicted and measured turbine damping characteristic, however the turbine efficiency was found to be poorly predicted. It is postulated that this is due to the unsteady nature and mal-distribution of flow through the LIMPET turbine, which were not considered in the predictions. It is suggested that the reduced performance of the contra-rotating Wells turbine makes biplane or monoplane Wells turbines with guide vanes better solutions for OWC's. 相似文献
5.
A numerical method is proposed to predict the effective wake profiles of high speed underwater vehicles propelled by contra-rotating propellers (CRPs), in which the hydrodynamic effects of the CRPs are simulated by distributed body forces. First, Reynolds-averaged Navier-Stokes (RANS) simulations are conducted for identical body-force distributions in open-water and self-propulsion conditions. The effective wake profiles at the CRP disks are then obtained by subtracting the velocities induced by the body forces in the open water from those induced by the body forces in the self-propulsion condition. The effective wake profiles were then predicted for a generic underwater vehicle with an established CRP design. Next, the hydrodynamic performance of the CRPs in the effective wake was computed using an in-house vortex-lattice code. The potential-flow results agree well with those provided by the RANS simulation under the self-propulsion condition, indicating that the proposed method can predict the effective wake profiles for CRPs with reasonable accuracy. The influences of different wake components on the blade forces were investigated, determining that for CRPs, and especially for the aft propeller, the circumferential wake cannot be neglected in the design. 相似文献
6.
A growing interest has been devoted to the contra-rotating propellers (CRPs) due to their high propulsive efficiency, torque balance, low fuel consumption, low cavitations, low noise performance and low hull vibration. Compared with the single-screw system, it is more difficult for the open water performance prediction because forward and aft propellers interact with each other and generate a more complicated flow field around the CRPs system. The current work focuses on the open water performance prediction of contra-rotating propellers by RANS and sliding mesh method considering the effect of computational time step size and turbulence model. The validation study has been performed on two sets of contra-rotating propellers developed by David W Taylor Naval Ship R & D center. Compared with the experimental data, it shows that RANS with sliding mesh method and SST k-ω turbulence model has a good precision in the open water performance prediction of contra-rotating propellers, and small time step size can improve the level of accuracy for CRPs with the same blade number of forward and aft propellers, while a relatively large time step size is a better choice for CRPs with different blade numbers. 相似文献
8.
The hydrodynamic characteristics of a marine propeller operating in oblique inflow are investigated by using CFD method. Two propellers with different geometries are selected as the study subjects. RANS simulation is carried out for the propellers working at a wide range of advance coefficients and incidence angles. The effects of axial inflow and lateral inflow are demonstrated with the hydrodynamic force on the propeller under different working conditions. Based on the obtained flow field details, the hydrodynamic mechanism of propeller operating in oblique inflow is analyzed further. The trailing vortex wake of propeller is highly affected by the lateral inflow, resulting in the deflected development path and the circumferentially non-uniform structure, as well as the enhanced axial velocity in slipstream. Different flow patterns are observed on the propeller blade with the variation of circumferential position. Combined with the computed hydrodynamic forces and pressure distribution on propeller, the mechanism resulting in the increase of propulsive loads and the generation of propeller side force is explored. Finally, a systematic analysis is carried out for the propulsive loads and propeller side force as a function of axial and lateral advance coefficients. The major terms that play a dominant role in the modeling of propulsive loads and propeller side force are determined through the sensitivity analysis. This study provides a deeper insight into the hydrodynamic characteristics of propeller operating in oblique inflow, which is useful to the investigation of propeller performance during ship maneuvers. 相似文献
9.
Conventional propellers might undergo severe cavitation at high speeds and this phenomenon not only affects the efficiency of the propeller, but also may result in serious damages in propulsion system. Due to their special geometries, surface piercing propellers (SPPs) overcome this problem and achieve high efficiencies in high speeds. Therefore, SPPs are one of the popular propulsors for high-speed crafts. The present research is aimed to pursue SPP's performance in the off-design conditions. URANS method was used to study the performance of the 841-B SPP (a case with some available experimental results; Olofsson, 1996) in several immersion ratios (I = 33%, 50%, 75% and 100%) and maneuvering conditions (incident angles of 0°, 10° and 20°). The free surface was simulated using VOF method. Off-design conditions might exert extra or less forces and torques on the propeller's blade. In the present research for 841-B SPP, it was found that a maneuver condition would increase the thrust and torque coefficient for some cases. The sliding mesh technique was utilized to simulate the 841-B SPP performance, which unlike the multiple reference frame (MRF) technique, this technique allows to capture the blades hit on the water surface in transient mode simulations. 相似文献
10.
This paper is the continuation of the work described in [14], dedicated to the presentation of the results of propeller performance in behind-hull during straight ahead motion obtained by a novel experimental set-up for the measurements of single blade loads. In the present case, the study shows and discusses the single blade and propeller loads developed during steady turning conditions, that were simulated by means of free running, self propelled maneuvering tests for a twin screw configuration. Maneuvering conditions are critical for the ship propulsion system, because the performance of the propeller and the side effects related to its functioning (propeller–hull induced pressure and vibrations, noise) are completely different with respect to the design condition in straight ahead motion. Thrust and torque and generation of in-plane loads (force and moments), developed by the blade during the period, evolve differently for the two propellers, due to different propeller–wake interactions. The understanding and the accurate quantification of propeller loads, in these realistic operative scenarios, are pivotal to design low emission and comfortable ships, fulfilling the requirements of safety and continuity of operations at sea. The analysis is carried out revisiting the investigation in [14] for three different speeds (FN = 0.26, 0.34 and 0.40) and a large set of rudder angles that span moderate and tight maneuvers. 相似文献
11.
Propeller modelling in CFD simulations is a key issue for the correct prediction of hull-propeller interactions, manoeuvring characteristics and the flow field in the stern region of a marine vehicle. From this point of view, actuator disk approaches have proved their reliability and computational efficiency; for these reasons, they are commonly used for the analysis of propulsive performance of a ship. Nevertheless, these models often neglect peculiar physical phenomena which characterise the operating propeller in off-design condition, namely the in-plane loads that are of paramount importance when considering non-standard or unusual propeller/rudder arrangements. In order to emphasize the importance of these components (in particular the propeller lateral force) and the need of a detailed propeller model for the correct prediction of the manoeuvring qualities of a ship, the turning circle manoeuvre of a self-propelled fully appended twin screw tanker-like ship model with a single rudder is simulated by the unsteady RANS solver χnavis developed at CNR-INSEAN; several propeller models able to include the effect of the strong oblique flow component encountered during a manoeuvre have been considered and compared. It is emphasized that, despite these models account for very complex and fundamental physical effects, which would be lost by a traditional actuator disk approach, the increase in computational resources is almost negligible. The accuracy of these models is assessed by comparison with experimental data from free running tests. The main features of the flow field, with particular attention to the vortical structures detached from the hull are presented as well. 相似文献
12.
A hybrid underwater glider Petrel-II has been developed and field tested. It is equipped with an active buoyancy unit and a compact propeller unit. Its working modes have been expanded to buoyancy driven gliding and propeller driven level-flight, which can make the glider work in strong currents, as well as many other complicated ocean environments. Its maximal gliding speed reaches 1 knot and the propelling speed is up to 3 knots. In this paper, a 3D dynamic model of Petrel-II is derived using linear momentum and angular momentum equations. According to the dynamic model, the spiral motion in the underwater space is simulated for the gliding mode. Similarly the cycle motion on water surface and the depth-keeping motion underwater are simulated for the level-flight mode. These simulations are important to the performance analysis and parameter optimization for the Petrel-II underwater glider. The simulation results show a good agreement with field trials. 相似文献
13.
《中国海洋工程》2017,(1)
A hybrid underwater glider Petrel-II has been developed and field tested. It is equipped with an active buoyancy unit and a compact propeller unit. Its working modes have been expanded to buoyancy driven gliding and propeller driven level-flight, which can make the glider work in strong currents, as well as many other complicated ocean environments. Its maximal gliding speed reaches 1 knot and the propelling speed is up to 3 knots. In this paper, a 3D dynamic model of Petrel-II is derived using linear momentum and angular momentum equations. According to the dynamic model, the spiral motion in the underwater space is simulated for the gliding mode. Similarly the cycle motion on water surface and the depth-keeping motion underwater are simulated for the level-flight mode. These simulations are important to the performance analysis and parameter optimization for the Petrel-II underwater glider.The simulation results show a good agreement with field trials. 相似文献
14.
During ice-breaking navigation, a massive amount of crushed ice blocks with different sizes is accumulated under the hull of an ice-going ship. This ice slides into the flow field in the forward side of the podded propulsor, affecting the surrounding flow field and aggravating the non-uniformity of the propeller wake. A pulsating load is formed on the propeller, which affects the hydrodynamic performance of the podded propulsor. To study the changes in the propeller hydrodynamic performance during the ice podded propulsor interaction, the overlapping grid technique is used to simulate the unsteady hydrodynamic performance of the podded propulsor at different propeller rotation angles and different ice block sizes. Hence, the hydrodynamic blade behavior during propeller rotation under the interaction between the ice and podded propulsor is discussed. The unsteady propeller loads and surrounding flow fields obtained for ice blocks with different sizes interacting with the podded propulsor are analyzed in detail. The variation in the hydrodynamic performance during the circular motion of a propeller and the influence of ice size variation on the propeller thrust and torque are determined. The calculation results have certain reference significance for experiment-based research, theoretical calculations and numerical simulation concerning ice podded propulsor interaction. 相似文献
15.
This paper presents the results of a numerical performance analysis to demonstrate the worthiness of a recently patented new concept propulsor, the so-called “thrust-balanced propeller (TBP)”. The main advantage of this unconventional propulsor is its inherent ability to reduce the unsteady effect of blade forces and moments when it is operating in a non-uniform wake flow. The propulsor comprises a pair of diametrically opposed blades that are connected to one another and mounted so as to be rotatable together through a limited angle about their spindle axis. A quasi-hydrodynamic approach is described and applied to perform the numerical analysis using a state-of-the-art lifting surface procedure for conventional propellers. Performance comparisons with a conventional fixed-pitch propeller are made for the blade forces and moments, efficiency, cavitation extents and fluctuating hull pressures. Bearing in mind the quasi-static nature of the analyses, the results present favourable performance characteristics for the thrust-balanced propeller and support the worthiness of the concept. However, the concept needs to be proved through physical model tests, which are planned to take in a cavitation tunnel. 相似文献
16.
The use of an unsteady computational fluid dynamic analysis of the manoeuvring performance of a self-propelled ship requires a large computational resource that restricts its use as part of a ship design process. A method is presented that significantly reduces computational cost by coupling a blade element momentum theory (BEMT) propeller model with the solution of the Reynolds averaged Navier Stokes (RANS) equations. The approach allows the determination of manoeuvring coefficients for a self-propelled ship travelling straight ahead, at a drift angle and for differing rudder angles. The swept volume of the propeller is divided into discrete annuli for which the axial and tangential momentum changes of the fluid passing through the propeller are balanced with the blade element performance of each propeller section. Such an approach allows the interaction effects between hull, propeller and rudder to be captured. Results are presented for the fully appended model scale self-propelled KRISO very large crude carrier 2 (KVLCC2) hull form undergoing static rudder and static drift tests at a Reynolds number of 4.6×106 acting at the ship self-propulsion point. All computations were carried out on a typical workstation using a hybrid finite volume mesh size of 2.1×106 elements. The computational uncertainty is typically 2–3% for side force and yaw moment. 相似文献
17.
In view of environmental concerns, there is increasing demand to optimize the ships for the actual operating condition rather than for calm water. Now, in order to apply this for propeller design, a first step would be to study the effects of waves on propeller operation. Therefore, the aim of this paper is to identify and quantify the effect of various factors affecting the propeller in waves. The performance of KVLCC2 propeller in the presence of three different waves has been compared with calm water performance. Changes in performance in terms of cavitation, pressure pulses, and efficiency have been studied. Significant increase in pressure pulses has been observed due to wake change in waves even though cavitation did not show any significant change. An analysis using cavitation bucket diagram in different wave conditions indicates that a propeller optimized for calm water wake may perform much worse in the presence of waves. Therefore, having wake variation at least in critical wave conditions (where the wavelength is close to ship length) in addition to calm water wake could be very useful to ensure that the propeller performs equally well in the presence of waves. 相似文献
18.
螺旋桨工作时在其周围形成诱导速度场,诱导速度随到桨叶距离的增大而衰减。采用CFD方法模拟螺旋桨敞水性能时,只能截取有限尺度的流域进行计算,此时计算域边界上诱导速度并不为零,将进口速度设为进速是近似的。一般采用足够大的计算域,使螺旋桨前方及侧面边界尽量远离桨叶。为了在较小的计算域中实现螺旋桨敞水性能的准确预报,提出在设定进口速度时计入螺旋桨诱导速度的CFD模拟方法。应用升力面方法计算诱导速度,将进口速度设为进速与诱导速度之和。逐步减小计算域尺度,考察敞水性能及压力分布计算结果的变化情况及精度。算例比较表明:通过考虑诱导速度,可以大幅度减小进口与螺旋桨的距离而不降低计算精度。 相似文献
19.
Specialized propulsors for naval applications have numerous opportunities in terms of research, design, and fabrication of an appropriate propulsor. One of the most important components of any propulsor is the actuator that provides the mode of locomotion. ionomeric electroactive polymer may offer an attractive solution for locomotion of small propulsors. A common ionomeric electroactive polymer, ionic polymer-metal composites (IPMCs) give large true bending deformations under low driving voltages, operate in aqueous environments, are capable of transduction, and are relatively well understood. IPMC fabrication and operation are presented to further elucidate the use of the material for a propulsor. Various materials, including IPMCs, are investigated and a simplified propulsor model is explored. 相似文献
20.
In practical maritime conditions, ship hulls experience heave motion due to the action of waves, which can further drive the ship’s propellers to oscillate relative to the surrounding water. In order to investigate the motion of a propeller working behind a surface vessel sailing in waves, a numerical simulation is conducted on a propeller impacted by heave motion in cavitating flow using the Reynolds-averaged Navier-Stokes (RANS) method. The coupling of the propeller’s rotation and translation is fulfilled using equations of motion defined for this purpose. The heave motion is simplified as a periodic motion based on a sinusoidal function. The numerical transmission of information from the unsteady flow field is achieved using the overset grid approach. In this manner, the unsteady thrust coefficient and torque coefficient of propellers in different periods of heave motion are analyzed. A comparative study is implemented on the unsteady cavitation performance and wake characteristics of propeller. With the propeller’s heave motion, the flow field non-uniformity constantly changes the load on the propeller during each revolution period and each heaving period, the propeller load and the wake field are closely related to the variation of heave motion period. The results obtained from the numerical simulation are expected to serve as a useful theoretical reference for the numerical analysis of a propeller in a heave motion. 相似文献