共查询到20条相似文献，搜索用时 15 毫秒
1.
Wells turbine with end plates for wave energy conversion 总被引：1，自引：0，他引：1
Manabu Takao Toshiaki Setoguchi Yoichi Kinoue Kenji Kaneko 《Ocean Engineering》2007,34(11-12):1790-1795
In order to improve the performance of the Wells turbine for wave energy conversion, the effect of end plate on the turbine characteristics has been investigated experimentally by model testing. As a result, it is found that the characteristics of the Wells turbine with end plates are superior to those of the original Wells turbine, i.e., the turbine without end plate and the characteristics are dependent on the size and position of end plate. Furthermore, by using a computational fluid dynamics (CFD), reason of the performance improvement of the turbine has been clarified and the effectiveness of the end plate has been demonstrated. 相似文献
2.
The Wells turbine is an axial-flow air-turbine designed to extract energy from ocean waves. An important consideration is the self-starting capability of the Wells turbine, a phenomenon encountered where the turbine accelerate by itself up to a certain speed for the best turbine performance. In order to clarify the self-starting characteristic and running performance of the Wells turbine in an irregular oscillating flow, a numerical simulation process is established in this paper on the rational assumption of quasi-steady flow conditions. Both self-starting characteristics and running performance are obtained through the numerical simulation and subsequently compared with the experimental data achieved on a computer-controlled oscillating flow test rig which could realize some irregular oscillating flow according to the specified spectrum. Results show that the self-starting time decreases with the increase of the significant wave height and the mean frequency of the irregular oscillating flow. Therefor 相似文献
3.
The performance of a Wells turbine with various non-uniform tip clearances was investigated using computational fluid dynamics (CFD). The investigation was performed on numerical models of a NACA0020 blade profile under steady flow conditions. The performance of turbines with uniform and non-uniform tip clearances was compared. The results were also compared with experimental results in literature. It was shown that the performance of turbine with non-uniform tip clearance is similar with that of turbine with uniform one in terms of torque coefficient, input power coefficient, and efficiency. However, the turbine with non-uniform tip clearance seems to have a preferable overall performance. An investigation on the flow-field around the turbine blade was performed in order to explain the phenomena. 相似文献
4.
1 .Introduction The Wells turbine ,consisting of several symmetric aerofoil blades ,fixedto a hub,can rotate inthe same direction without anyrectifyingflap valves .It has been consideredto bethe most prospectivewave energy conversion deviceforits simple s… 相似文献
5.
Analysis of Wells turbine design parameters by numerical simulation of the OWC performance 总被引：1，自引：0，他引：1
This paper investigates by numerical simulation the influence of the Wells turbine aerodynamic design on the overall plant performance, as affected by the turbine peak efficiency and the range of flow rates within which the turbine can operate efficiently. The problem of matching the turbine to an oscillating water column (OWC) is illustrated by taking the wave climate and the OWC of the Azores power converter. The study was performed using a time-domain mathematical model based on linear water wave theory and on model experiments in a wave tank. Results are presented of numerical simulations considering several aerodynamic designs of the Wells turbine, with and without guide vanes, and with the use of a bypass pressure-relief valve. 相似文献
6.
The paper presents the effects of blade twist and nacelle shape on the performance of horizontal axis tidal current turbines using both analytical and numerical methods. Firstly, in the hydrodynamic design procedure, the optimal profiles of untwisted and twisted blades and their predicted theoretical turbine performance are obtained using the genetic algorithm method. Although both blade profiles produce desired rated rotational speed, the twisted blade achieves higher power and thrust performance. Secondly, numerical simulation is performed using sliding mesh technique to mimic rotating turbine in ANSYS FLUENT to validate the analytical results. The Reynolds-Averaged Navier-Stokes (RANS) approximation of the turbulence parameters is applied to obtain the flow field around the turbine. It is found that power and axial thrust force from BEMT (Blade Element Momentum Theory) method are under-predicted by 2% and 8% respectively, compared with numerical results. Afterwards, the downstream wake field of the turbine is investigated with two different nacelle shapes. It is found that the rotor performance is not significantly affected by the different nacelle shapes. However, the structural turbulence caused by the conventional nacelle is stronger than that by the NACA-profiled shape, and the former can cause detrimental effect on the performance of the downstream turbines in tidal farms. 相似文献
7.
8.
A growing interest has been devoted to the contra-rotating propellers (CRPs) due to their high propulsive efficiency, torque balance, low fuel consumption, low cavitations, low noise performance and low hull vibration. Compared with the single-screw system, it is more difficult for the open water performance prediction because forward and aft propellers interact with each other and generate a more complicated flow field around the CRPs system. The current work focuses on the open water performance prediction of contra-rotating propellers by RANS and sliding mesh method considering the effect of computational time step size and turbulence model. The validation study has been performed on two sets of contra-rotating propellers developed by David W Taylor Naval Ship R & D center. Compared with the experimental data, it shows that RANS with sliding mesh method and SST k-ω turbulence model has a good precision in the open water performance prediction of contra-rotating propellers, and small time step size can improve the level of accuracy for CRPs with the same blade number of forward and aft propellers, while a relatively large time step size is a better choice for CRPs with different blade numbers. 相似文献
9.
《Ocean Engineering》2004,31(11-12):1407-1421
The paper presents an optimization study for the mechanical and electrical equipment of an oscillating-water-column (OWC) wave power plant of fixed shoreline or nearshore type, equipped with an air turbine. The plant’s structure geometry is assumed to be given and the corresponding hydrodynamic coefficients are known as functions of wave frequency. A stochastic model is adopted for the energy conversion process from wave to air turbine, it being assumed that the system is linear. The optimization concerns the turbine size, represented by its rotor diameter D. Two alternative criteria are used: (i) maximization of the produced electrical energy, (ii) maximization of the annual profit. An example calculation is presented, based on the hydrodynamic coefficients of the OWC on the island of Pico, Azores, and on the aerodynamic performance curves of its Wells turbine. The influence of the following parameters upon optimized turbine size and rated power output is analyzed: wave climate, capital costs of mechanical and electrical equipment, operation and maintenance costs, discount rate, equipment lifetime and price of electrical energy supplied to the grid. 相似文献
10.
The paper presents a concept of a wave energy converter and the numerical model to calculate the hydrodynamic responses in waves and the power produced by the power take off system. The system consists of an asymmetric floater with an interior U-tank partially filled with water and two lateral air chambers connected by a duct. The motion of the U-shaped oscillating water column, mainly induced by the rolling of the floater, forces the air through the duct where a Wells turbine is installed to absorb the wave energy.The wave-floater hydrodynamics is calculated with a Green's function panel method, while the oscillating water column motions hydro-mechanics are derived from the one-dimensional Euler's equation. The dynamics of the Wells turbine is realistically represented by one additional differential equation on the unknown air pressure fluctuation. This equation is derived assuming small amplitude motions of the water column and assuming the linear isentropic relation is valid for the air thermodynamics in the air chambers. The Wells turbine is characterized by a drastic drop of efficiency above a critical pressure value due to stalling on the blades. The effect of a by-pass valve to prevent stalling is introduced in the numerical model in a simplistic way. The numerical model is implemented and tested for a wave energy converter with a displacement of 1150 t, including 490 t for the interior water column, and an installed turbine with 2.3 m of diameter. An analysis of the influence of changing different design parameters on the system efficiency is also presented. 相似文献
11.
An integral panel method (IPM) that treats the different components of multi-component propulsors as a whole is presented for efficient propulsor performance analysis. The IPM requires consider only one blade of the propeller in the performance analysis, which significantly reduces the number of computation grid. The control equations of the IPM are derived in detail for podded propulsors, contra-rotating propellers and hybrid contra-rotating shaft pod propulsors, and based on these derivations, a general control equation for multi-component propulsors with propeller is derived. Comparison between numerical results and experimental data show that the IPM provides good accuracy for the performance analysis of multi-component propulsors with propeller. In addition, the error sources of IPM are discussed, and the reasonableness of these errors is evaluated. 相似文献
12.
Control strategies for the Clam Wave Energy Device 总被引：1，自引：0，他引：1
A promising wave energy device being currently investigated is the ‘clam’. The clam extracts energy by pumping air through a specially designed (Wells) turbine. Although operation of the Wells turbine does not require a rectified air flow, some additional control will be necessary to optimize the phase of the clam motion for good efficiencies. An examination of the equation of motion in the time domain suggests the possibility of phase control by mechanical, power take-off, or pneumatic latching. Latching can be shown to increase the efficiency of the device in the longer wavelengths of the wave spectrum, i.e. those of high incident wave power. Equivalently latching could be used to keep the device efficiency high while reducing its size, possibly resulting in cheaper power extraction. 相似文献
13.
OWC wave energy devices with air flow control 总被引：1，自引：0，他引：1
A theoretical model is developed to simulate the energy conversion, from wave to turbine shaft, of an oscillating-water-column (OWC) plant equipped with a Wells air-turbine and with a valve (in series or in parallel with the turbine) for air-flow control. Numerical simulations show that the use of a control valve, by preventing or reducing the aerodynamic stall losses at the turbine rotor blades, may provide a way of substantially increasing the amount of energy produced by the plant, particularly at the higher incident wave power levels. From the hydrodynamic point of view, a by-pass valve or a throttle valve should be used depending on whether the wave energy absorbing system is over-damped or under-damped by the turbine. 相似文献
14.
通过水轮机捕能是当前常用的海洋能利用方式之一。桨叶作为水轮机关键部件,其性能一直是研究的重点。针对目前波浪条件下带负载运转的Savonius型水轮机相关捕能性能研究较少的情况,采用数值仿真方法,结合对应工况条件的物理试验,研究了一种Savonius型水轮机在不同波浪环境下带负载运转的捕能性能。采用Star CCM+仿真软件,建立数值波浪水池,设置环境参数,划分网格调整变量进行水轮机运转的水动力模型数值研究。在造波试验水池中利用推板改变波浪周期与波高,进行水轮机运转的物理试验。采集在不同负载下水轮机桨叶的转速和扭矩数据,计算并分析功率等参数,总结变化趋势,评价捕能效果。研究发现水轮机在1.6 s的波浪周期条件下,桨叶承受1.5 N·m负载时达到最佳捕能效果,其功率为23 W。为实际海域中水轮机桨叶的结构设计研究和相关工程应用提供参考。 相似文献
15.
Tidal current energy is prominent and renewable. Great progress has been made in the exploitation technology of tidal current energy all over the world in recent years, and the large scale device has become the trend of tidal current turbine (TCT) for its economies. Instead of the similarity to the wind turbine, the tidal turbine has the characteristics of high hydrodynamic efficiency, big thrust, reliable sealing system, tight power transmission structure, etc. In this paper, a 1/5th scale horizontal axis tidal current turbine has been designed, manufactured and tested before the full scale device design. Firstly, the three-blade horizontal axis rotor was designed based on traditional blade element momentum theory and its hydrodynamic performance was predicted in numerical model. Then the power train system and stand-alone electrical control unit of tidal current turbine, whose performances were accessed through the bench test carried out in workshop, were designed and presented. Finally, offshore tests were carried out and the power performance of the rotor was obtained and compared with the published literatures, and the results showed that the power coefficient was satisfactory, which agrees with the theoretical predictions. 相似文献
16.
Wave tank tests were carried out to evaluate the total efficiency of a floating OWC Pentagonal Backward Bent Duct Buoy (PBBDB). Two kinds of turbine generators were used in tests. The incident wave power, pneumatic power and electricity were measured. The test results show that the primary efficiency can reach up to 185.98% in regular waves and 85.86% in irregular waves. The total efficiency from wave to wire with Wells turbine-generator set is 33.43% in regular waves and 15.82% in irregular waves. The peak total efficiency of the PBBDB with check valves equipped with the impulse turbine-generator set is 41.68% in regular waves and 27.10% in irregular waves. The efficiency of the turbine-generator set is about 30% in the tests. Obviously, the total efficiency can be further improved with the increasing of turbine efficiency.
相似文献17.
A numerical method is proposed to predict the effective wake profiles of high speed underwater vehicles propelled by contra-rotating propellers (CRPs), in which the hydrodynamic effects of the CRPs are simulated by distributed body forces. First, Reynolds-averaged Navier-Stokes (RANS) simulations are conducted for identical body-force distributions in open-water and self-propulsion conditions. The effective wake profiles at the CRP disks are then obtained by subtracting the velocities induced by the body forces in the open water from those induced by the body forces in the self-propulsion condition. The effective wake profiles were then predicted for a generic underwater vehicle with an established CRP design. Next, the hydrodynamic performance of the CRPs in the effective wake was computed using an in-house vortex-lattice code. The potential-flow results agree well with those provided by the RANS simulation under the self-propulsion condition, indicating that the proposed method can predict the effective wake profiles for CRPs with reasonable accuracy. The influences of different wake components on the blade forces were investigated, determining that for CRPs, and especially for the aft propeller, the circumferential wake cannot be neglected in the design. 相似文献
18.
The energy saving performance of contra-rotating azimuth propulsor (CRAP) is investigated based on low order potential-based panel method. The hydrodynamic interactions among the forward propeller (FP), rear propeller (RP) and the pod unit (PU) which includes the pod body and the strut are considered through induced velocities which are obtained by panel method. In order to have a better understanding about the energy saving performance of CRAP, the hydrodynamic performance of a conventional propeller (CP) supplying the same thrust with CRAP at design condition is also calculated. At design condition, CRAP has a decrease in delivered power by approximately 8% comparing with CP, and the tangential induced velocities in slipstream show that CRAP recovers the rotational energy of slipstream effectively. At off-design conditions, the rotational speed of CRAP is adjusted to supply the same thrust with CP. In general, the delivered power of CRAP is significantly smaller than that of CP, and the energy saving performance of CRAP increases with the decrease of inflow velocity. 相似文献
19.
径流式空气透平是振荡水柱式波能发电系统的二级能量转换装置,因其具有结构简单、输出扭矩大、轴向推力小的优势,得到了越来越多的关注。采用计算流体力学软件Ansys-Fluent 12.0,通过数值模拟方法考察了不同转子叶片稠度对径流式空气透平定常无量纲评价参数的影响规律。研究结果表明:虽然径流式透平可在双向气流下实现单向旋转,但当气流通过方向不同时,透平的定常工作性能存在明显差异,这与传统轴流式透平完全不同;此外,稠度对透平效率的影响在不同流量系数范围内也不同。因此,综合考虑气流流向、透平整个工作范围内输出效率,推荐采用的转子叶片稠度为2.34。 相似文献
20.
为了研究潮流能水轮机尾流场的变化规律,本文在水平轴水轮机现有理论基础上,采用计算流体力学技术建立了数值模型,计算了水轮机的功率特性,进行了网格独立性验证,比较了模型中旋转区域不同对结果的影响。仿真结果与试验结果进行了对比分析,验证了数值模型的有效性。研究了全工况下尾流场速度衰减随尖速比和距离变化的规律,结果显示在小尖速比下尾流场速度恢复情况相对大尖速比下较好;靠近水轮机轮毂中心线位置处,衰减相对较大。研究建议水轮机在同等功率表现下尽量选择在小尖速比下工作,水轮机组在实际排列时避免采用成列布置,水轮机设计阶段应综合考虑功率特性和尾流场衰减。本文研究内容可以为潮流能水轮机的研究以及阵列式应用提供参考。 相似文献