首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
气枪主动源探测实验需要获得信噪比较优的波形数据,因此实验前很有必要进行不同工况的激发实验。通过综合分析台站记录特征,寻找最优激发效果的工况条件,为后续定点激发奠定重要基础。本文在福建南一水库大容量气枪震源实验时通过单次激发分析、叠加分析、信噪比系数等方法综合研判工况激发效果,确定出最优工况,再利用台网噪声评估对得到的最优工况做进一步验证。结果表明:南一水库最优工况为:水深25m、枪阵沉放深度12 m、枪阵尺寸7 m×7 m。该最优工况激发时段未处在低噪声时刻,说明该工况的激发效果确为优越,结果较为可靠。  相似文献   

2.
台网噪声评估及其对气枪震源激发效果影响的研究   总被引:1,自引:0,他引:1       下载免费PDF全文
为了研究背景噪声对长江地学气枪主动源实验激发效果的影响,收集了240个台站激发前72小时的背景噪声数据及20个定点激发的叠加结果进行实验分析.先剔除异常台站,按照国标将台网噪声水平划分为高、中、低3个等级进行评估,从而研究气枪波形信噪比与台站背景噪声的关系.结果表明:① 台站接收能力与背景噪声水平密切相关;② 气枪信号的信噪比在一定范围内受背景噪声的影响大于距离衰减的影响;③ 长江马鞍山—安庆流域段不同定点激发的场地条件基本一致;④ 随气枪信号叠加次数的增加,低噪台站的信噪比增长速度快于中、高噪台站,若想获得同样的叠加效果,高噪台站需要的叠加次数远大于低噪台站.   相似文献   

3.
对地震动空间相干函数进行拟合时,常常遇到台站间距离d偏少的问题。对不同距离台站对的不足对相干函数模型拟合参数的影响进行了对比分析。选取了SMART-1台阵第45号地震的水平分量加速度作为分析数据,计算了d等于200 m,1 000 m和2 000 m等3个台站间距的空间相干系数,并对3个距离的所有计算值进行了拟合,得到了第一组拟合参数;另外又增加计算了d等于400 m,800 m和1 200 m等3个台站间距的空间相干系数,并对所有6个距离的计算值进行了拟合,得到了第二组拟合参数。结果表明,第二组拟合参数的离散性优于第一组拟合参数,且根据第二组拟合参数计算得到的相干系数曲线更合理。因此建议,当采用统计方法获得地震动空间相干函数时,应尽量多地考虑不同距离台站对的强震记录。  相似文献   

4.
栾奕  杨宏峰  王宝善 《中国地震》2016,32(2):305-318
宾川气枪地震信号发射台以水库大容量非调制气枪阵列为震源,可以连续不断地激发重复性极高的地震信号。本文利用其2013年的数据,对地下介质进行了观测。由于水库水位的变化对震源波形及远处台站接收到的地震波形会产生影响,因此,为了区分介质变化与震源变化,研究了陆上水库环境下激发气枪震源所产生的地震波形的特征和合适的处理流程。结果表明:1水库水位变化较大时,同一台站记录的地震波形之间的互相关系数过小,不能直接进行叠加处理,需进行震源聚类分析,而震源聚类受水位变化量的控制;2为消除水位的影响,进行了反褶积处理,当震中距小于10km时,对不同水位激发的信号进行叠加再进行反褶积的效果优于直接进行叠加的效果;3通过互相关计算和信噪比分析发现,4个台站的波形变化可能是由地下介质变化引起的。  相似文献   

5.
大容量气枪震源激发探测因具绿色环保、传播距离远和高度重复性等特点成为地下介质探测的新方法,利用其进行地下介质物性变化高精度探测,则对不同激发条件下气枪传播信号的一致性提出要求。本文选取了祁连山主动源不同枪组(4支和3支气枪)在激发环境一致情况下分别激发时各远台波形记录,通过信号叠加、互相关及频谱分析等方法,对比分析了各台站记录的不同枪组激发信号,及其与震中距的关系,并讨论了不同枪组激发对地下介质走时变化观测的影响。结果表明:(1)不同枪组的激发信号波形相关度随震中距增大而降低,信号震相随激发能量有微弱的变化,震中距超过50 km后其变化几乎分辨不出;(2)远台接收信号的能量大小随主动源激发能量变化,各台站能量变化主要体现在优势频率范围内;(3)接收台站台基越坚固不同激发能量均方根振幅比越小;(4)叠加一定数量的波形可以有效提高远台记录信号的信噪比,增加气枪激发能量则相对更容易提高信号信噪比。  相似文献   

6.
可控震源的激发过程精确可控、可重复性高。本文评估了重复激发形成的多道记录的信号增强方法,包括叠加方法和有效信号直接分离方法。相比线性叠加,加权叠加充分利用了有效信号的一致性,能进一步压制噪声,提高叠加记录的信噪比。相比时间域相位加权叠加,Semblance加权叠加更加稳定。时频域相位加权叠加能在时频域压制随机分散分布的噪声信号,叠加信号更加清晰。本文中,采用标准SVD分离获得的信号同线性叠加结果类似。本文利用密集分布的临时台阵评价地学长江计划安徽实验中低频可控震源在庐江第2激发点的激发效果。对比不同的处理流程发现,先互相关检测信号再进行时频域相位加权叠加能够取得最佳的处理效果,通过200多次重复激发,可以在50km范围内提取到较清晰的有效信号。  相似文献   

7.
应用S变换对比分析云南宾川地震信号发射台单次气枪激发信号与同当量天然地震信号在传播过程中的波形和频率特征,并基于参考台聚类分析结果,对其他接收台站的地震信号进行线性叠加和相位加权叠加,研究结果表明:(1)气枪信号传播过程中主频为3~6 Hz,可以在距离为151 km的台站检测到信号,传播过程中能量衰减较慢。天然地震信号主频较高,在传播7.7 km时的主频为10~20 Hz,传播距离约为60 km,传播过程中能量衰减较快;(2)经过2 000余次的线性叠加和相位加权叠加,可以分别在距离为225 km和350 km的台站检测到气枪信号。与天然地震信号相比,气枪信号数据丰富、衰减慢、传播距离远,利用气枪数据可以研究更大范围的地壳介质结构。  相似文献   

8.
小当量激发的远距离信号检测研究   总被引:5,自引:1,他引:4       下载免费PDF全文
为了研究利用小当量震源进行远距离探测的可能性,通过现场试验进行了研究.野外实验采用1次大当量激发和16次小当量激发,研究结果表明:①有可能利用数十公斤当量的炸药实现200km距离的探测;②在激发条件相同(或相近)时,不同当量的激发波形滤波后存在一定的相似性;③依据人工震源可重复性采用以下的激发组合方式和处理方法能够有效提高信噪比:针对大当量激发与小当量激发波形的相似性,利用大当量激发的波形作模板与小当量激发的波形作相关,可判断台站是否接受到小当量激发的信号并检测其震相到时信息.针对小当量激发波形的相似性,采用小当量多次激发的方式,通过N次根加权叠加方法,能有效提高记录的信噪比和震相识别精度.  相似文献   

9.
Chin-Jen  Lin  Chun-Chi  Liu  William  H.  K.  Lee  冯静 《世界地震译丛》2010,(2):38-53
2008年3月4日在台湾东北部的N3爆破点实施了两次爆破。第一次3000kg炸药的爆破编号为N3P,第二次750kg炸药的爆破编号为N3。为了记录这两次爆破,我们使用了8个三轴旋转传感器、13个三轴加速度计以及12个装有全球定位系统接收器的6通道24位数据记录仪在爆破前后几小时进行连续观测。这些仪器安装在距离爆破点250m(1个台)、500m(11个台)、600m(1个台)的地方,其中距离爆破点500m的11个台站形成了台站间距约为5m的中心台阵。除一个旋转传感器外,都得到了量程内的记录。尽管N3P爆破使用的炸药是N3爆破的4倍,但是13个台站记录的N3P爆破的平移加速度和旋转速度的峰值却只有N3爆破的1.5倍。在台站间距大约5m的中心台阵的记录中,我们还发现平移加速度和旋转速度变化很大(百分之几十)。N3P和N3爆破的最大峰值旋转速度分别为2.74mrad/s和1.75mrad/s。本文的主要目的是报告台湾这两次爆破的旋转和平移运动记录,并在网上发布以开放访问。Langston等(2009)已经对本次试验的平移加速度数据进行了分析,我们计划未来发表一篇关于分析旋转速度数据的文章。  相似文献   

10.
通过分析福建街面水库气枪实验的OBS竖向速度记录,研究大容量气枪阵列子波时频特性及其受气枪数量和枪阵尺寸的影响。数据分析结果表明:(1)气枪子波由主脉冲和气泡脉冲组成,同时伴随有水面虚反射引起的负脉冲。主脉冲振幅大、持时短、频带宽,通常应用于浅部探测;气泡脉冲能量集中在低频段,垂直穿透深,水平传播远,通常应用于深部探测。在频谱上可以看到气泡振荡引起的频谱波动和虚反射引起的陷波点。(2)气枪数量增加,主脉冲振幅和气泡脉冲振幅相应增加,初泡比震荡变小,气泡周期和低频段主频主要受单枪容量影响,变化很小,频谱形状较为一致。(3)街面水库气枪阵列的枪阵尺寸远大于单枪气泡半径,各枪子波之间相互作用很小,枪阵子波近似为各枪子波线性叠加,子波参数随枪阵尺寸变化影响不大。  相似文献   

11.
12.
A procedure for short-term rainfall forecasting in real-time is developed and a study of the role of sampling on forecast ability is conducted. Ground level rainfall fields are forecasted using a stochastic space-time rainfall model in state-space form. Updating of the rainfall field in real-time is accomplished using a distributed parameter Kalman filter to optimally combine measurement information and forecast model estimates. The influence of sampling density on forecast accuracy is evaluated using a series of a simulated rainfall events generated with the same stochastic rainfall model. Sampling was conducted at five different network spatial densities. The results quantify the influence of sampling network density on real-time rainfall field forecasting. Statistical analyses of the rainfall field residuals illustrate improvement in one hour lead time forecasts at higher measurement densities.  相似文献   

13.
14.
正This journal is established by the Institute of Engineering Mechanics(IEM),China Earthquake Administration,to promote scientific exchange between Chinese and foreign scientists and engineers so as to improve the theory and practice of earthquake hazards mitigation,preparedness,and recovery.To accomplish this purpose,the journal aims to attract a balanced number of papers between Chinese and  相似文献   

15.
Water quality analyses for the Niger River for the 1980/81 hydrological year are presented. The samples were collected from the main river at Lokoja, and from two main tributaries, the Kaduna and the Benue Rivers. Different water types were distinguished by the concentrations of major ions. The type Ca > Na > Mg > K - HCO3 > SO4 > Cl was represented at all stations during at least part of the year. Chloride was found to dominate the sulphate ion in the Kaduna and Niger, while the Benue maintained a higher concentration of sulphate relative to chloride all year round. Distinct patterns of seasonal variation in the ion concentrations were observed, particularly for the samples collected at Lokoja. Low ion concentrations were prominent during periods of high discharge, while low flow periods coincided with high dissolved ion concentrations. The contribution of rainwater to the total dissolved solids in the river waters was assessed indirectly using rainwater chemistry data from the Gulf of Guinea. The estimated rainwater contribution to the Lower Niger amounts to 5.15 mg 1?1. Geochemical weathering calculations involving reactions of the four major minerals of granitic rocks - anorthite, biotite, albite, and K-feldspar - with carbon dioxide and water, can account for the average water composition of the Lower Niger. The proportion of the ionic components was also related to the occurrence of the respective element in the minerals.  相似文献   

16.
Historical earthquakes noted in the written records of the South China region, including Hong Kong, are not well delineated along identified prominent fault sources. Despite the lack of any definitive, localised trend in the spatial distribution of seismic activity in the region, there does appear to be some major disparity in the seismic activity rates (especially for large magnitude earthquakes) between the near-field and the far-field regions of Hong Kong. Despite this observation, previous studies of the regional seismic activity and seismic ground motion hazard (the latter using a probabilistic seismic hazard assessment, PSHA) have considered very broad source zone regions, in which uniform levels of seismic activity have been assumed. The present paper further scrutinises this broad source zone (BSZ) approach by adopting a novel expanding circular disc (ECD) method to determine the rates of earthquake recurrence. Such a method is intended to counter-check previously developed models by determining earthquake scenario events in terms of magnitude–distance (M–R) pairs or combinations, having defined values of average return period. Unlike the BSZ approach, the ECD method specifically accounts for the supposed variations in the seismic activity rates between events in the near-field and the far-field of Hong Kong.The form of the developed method is particularly suited to the determination of design-level earthquake ground motions for bedrock sites, since it assumes a directionally-independent attenuation model as described in the companion paper. It is found that, whilst the BSZ approach may indicate the overall average levels of hazard that are representative of the South China region as a whole, it does not capture the large disparity in seismic activity rates between near-field and far-field events. This important feature is expected to have a significant impact upon engineering assessments of the seismic safety of structures in Hong Kong and elsewhere in the South China region. For example, it is found that for events with M≥6, the seismic activity rate (normalised by time and area) in the very far-field is around 3.5 times larger than in the near-field and medium-field of Hong Kong. The resulting design M-R combinations, covering a range of return periods from 70 to 2500 years, are limited, for very long return periods and for distant events, by the maximum credible earthquake (MCE) magnitude. Intensive research to determine this seismic hazard parameter is recommended, in order to refine further the results of the ECD analysis, which presently conservatively assumes the MCE to range between M=6 in the near-field of Hong Kong to M=8 in the very far-field, at distances greater than 280 km from Hong Kong.  相似文献   

17.
Lower Cretaceous lacustrine oil shales are widely distributed in southeastern Mongolia. Due to the high organic carbon content of oil shale, many geochemical studies and petroleum exploration have been conducted. Although most of the oil shales are considered to be Early Cretaceous in age, a recent study reveals that some were deposited in the Middle Jurassic. The present study aims at establishing depositional ages and characteristics of the Jurassic and Cretaceous lacustrine deposits in Mongolia. The Lower Cretaceous Shinekhudag Formation is about 250 m thick and composed of alternating beds of shale and dolomite. The Middle Jurassic Eedemt Formation is about 150 m thick and composed of alternating beds of shale, dolomitic marl, and siltstone. The alternations of shale and dolomite in both formations were formed by lake level changes, reflecting precipitation changes. Shales were deposited in the center of a deep lake during highstand, while dolomites were formed by primary precipitation during lowstand. Based on the radiometric age dating, the Shinekhudag Formation was deposited between 123.8 ±2.0 Ma and 118.5 ±0.9 Ma of the early Aptian. The Eedemt Formation was deposited at around 165–158 Ma of Callovian–Oxfordian. The calculated sedimentation rate of the Shinekhudag Formation is between 4.7 ±2.6 cm/ky and 10.0 ±7.6 cm/ky. Shales in the Shinekhudag Formation show micrometer‐scale lamination, consisting of algal organic matter and detrital clay mineral couplets. Given the average thickness of micro‐laminae and calculated sedimentation rate, the micro‐lamination is most likely of varve origin. Both Middle–Upper Jurassic and Lower Cretaceous lacustrine oil shales were deposited in intracontinental basins in the paleo‐Asian continent. Tectonic processes and basin evolution basically controlled the deposition of these oil shales. In addition, enhanced precipitation under humid climate during the early Aptian and the Callovian–Oxfordian was another key factor inducing the widespread oil shale deposition in Mongolia.  相似文献   

18.
ABSTRACT

The one-dimensional transient downward entry of water in unsaturated soils is investigated theoretically. The mathematical equation describing the infiltration process is derived by combining Darcy's dynamic equation of motion with the continuity and thermodynamic state equations adjusted for the unsaturated flow conditions. The resulting equation together with the corresponding initial and boundary conditions constitues a mathematical initial boundary value problem requiring the solution of a nonlinear partial differential equation of the parabolic type. The volumetric water content is taken as the dependent variable and the time and the position along the vertical direction are taken as the independent variables. The governing equation is of such nature that a solution exists for t > 0 and is uniquely determined if two relationships are defined, together with the specified state of the system, at the initial time t = 0 and at the two boundaries. The two required relations are those of pressure versus permeability and pressure versus volumetric water content.

Since the partial differential equation has strong non-linear terms, a discrete solution is obtained by approximating the derivatives with finite-differences at discrete mesh points in the solution domain and integrated for the corresponding initial and boundary conditions. The use of an implicit difference scheme is employed in order to generate a system of simultaneous non-linear equations that has to be solved for each time increment. For n mesh points the two boundary conditions provide two equations and the repetition of the recurrence formula provides n—2 equations, the total being n equations for each time increment. The solution of the system is obtained by matrix inversion and particularly with a back-substitution technique. The FORTRAN statements used for obtaining the solution with an electronic digital computer (IBM 704) are presented together with the input data.

Analysis of the errors involved in the numerical solution is made and the stability and convergence of the solution of the approximate difference equation to that of the differential equation is investigated. The method applied is that of making a Fourier series expansion of a whole line of errors and then following the progress of the general term of the series expansion and also the behavior of each constituent harmonic. The errors (forming a continuous function of points in an abstract Banach space) are represented by vectors with the Fourier coefficients constituting a second Banach space. The amplification factor of the difference equation is shown to be always less than unity which guarantees the stability of the employed implicit recurrence scheme.

Experiments conducted on a vertical column packed uniformly with very fine sand, show a satisfactory agreement between the theoretically and experimentally obtained values. Many experimental results are shown in an attempt to explain the infiltration phenomenon with emphasis on the shape and movement of the wet front, and the effects of the degree of compaction, initial water content and deaired water on the infiltration rate.  相似文献   

19.
20.
GHODRAT TORABI 《Island Arc》2012,21(3):215-229
Late Permian trondhjemites in the Anarak area occur as stocks and dykes, which cross cut the Anarak ophiolite and its overlying metasedimentary rocks, and are exposed along the northern Anarak east–west main faults. These leucocratic intrusive bodies have enclaves of all ophiolitic units and metamorphic rocks. They are composed of amphibole, plagioclase (oligoclase), quartz, zircon and muscovite. Secondary minerals are chlorite (pycnochlorite), epidote, albite, magnetite and calcite. Whole‐rock major‐ and trace‐element analyses reveal that they are characterized by high SiO 2 (67.8–71.0 wt%), Al 2 O 3 (14.9–17.1 wt%) and Na 2 O (5.3–8.6 wt%), low K 2 O (0.1–1.5 wt%; average: 0.8 wt%), low Rb/Sr ratio (0.01–0.40; average: 0.09), low Y (3–6 ppm), negative Ti, Nb and Ta anomalies, slightly negative or positive Eu anomaly, LREE enrichment and fractionated HREE. These rocks present 2 to 40 times enrichment in inclined chondrite‐normalized REE patterns. Geochemical characteristics of the Anarak trondhjemites all reflect melting of a mafic protolith at more than 10 kbar. The field evidence and whole‐rock chemistry reveal that these rocks have been crystallized from magmas derived from melting of subducted Anarak oceanic crust. This study reveals that melting of garnet amphibolite was an important element of continent formation in the study area.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号