首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 562 毫秒
1.
Prediction of the seismic rotational displacements of retaining wall under passive condition is an important aspect of design in earthquake prone region. In this paper, the pseudo-dynamic method is used to compute the rotational displacements of rigid retaining wall supporting cohesionless backfill under seismic loading for the passive earth pressure condition. The proposed method considers time, phase difference and effect of amplification in shear and primary waves propagating through both the backfill and the retaining wall. The influence of ground motion characteristics on rotational displacement of the wall is evaluated. Also the effects of variation of parameters like wall friction angle, soil friction angle, amplification factor, shear wave velocity, primary wave velocity, period of lateral shaking, horizontal and vertical seismic accelerations on the rotational displacements are studied. The rotational displacement of the wall increases substantially with increase in amplification of both shear and primary waves, time of input motion, period of lateral shaking and decreases with increase in soil friction angle, wall friction angle. The rotational displacements of the wall also increase when the effect of wall inertia is taken into account. Results are provided in graphical form.  相似文献   

2.
Novel approaches to the dynamic analysis of the reinforced soil walls have been reported in the literature. Use of marginal soils reduces the cost of geosynthetic reinforced soil walls if proper drainage measures are taken. Therefore the affect of using cohesive marginal soils as backfill in geosynthetic reinforced retaining structures were investigated in this research. The dynamic response of reinforced soil walls was investigated in a similar focus, using finite element analysis. The results obtained from walls with cohesive backfill were compared to the results obtained from walls with granular backfill. The height of the wall was chosen as 6 m in the two-dimensional plane strain finite element model and the base acceleration was chosen to be a harmonic motion. The effects of various parameters like the backfill type, facing type, reinforcement stiffness, and peak ground acceleration on the cyclic response of reinforced soil retaining walls were investigated. After analyzing the wall response for end of construction and dynamic excitation phases, it was determined that the deformations and reinforcement tensile loads increased during the cyclic load application and that the amount of additional deformation that occurred during cyclic load application was strongly related to backfill soil type, facing type, reinforcement type and peak ground acceleration. It was determined that a cohesive backfill and geotextile reinforcement was a good combination to reduce the deformations of geosynthetic reinforced walls during cyclic loading for medium height walls.  相似文献   

3.
土工格栅加筋挡土墙是一种柔性挡土结构,目前尚未建立较严密的设计方法,作用在土工格栅加筋墙壁上的地震动土压力研究是抗震设计的重要内容之一。应用基于拉格朗日法的完全非线性动有限差分法研究整体面板式土工格栅加筋土挡壁在地震作用下各设计参数对挡壁动土压力的影响。采用弹塑性模型模拟填土,采用耦合弹性参数描述格栅与土接触界面特性,参数包括加筋间距、长度、刚度、地震强度和填土性质等,分析墙壁的动土压力沿墙身的分布特征,得出了影响地震动土压力的显著参数,证明了土工格栅加筋墙体的优异吸震能力,研究结果为整体面板式土工格栅加筋土挡墙抗震设计中的动土压力研究提供参考。  相似文献   

4.
挡土墙地震被动土压力的拟动力分析   总被引:5,自引:0,他引:5  
杨剑 《地震学刊》2012,(3):365-371
对地震土压力的研究是地震区挡土墙安全设计的一项重要课题。地震条件下,目前的研究主要是给出了土压力的近似拟静力解析解。本文采用可考虑动力荷载下的周期和纵波及横波效应的拟动力方法,对挡土墙后的地震被动土压力进行分析。在挡土墙后平面滑裂面假设的基础上,考虑了水平和垂直向地震加速度、纵波速度、横波速度、挡土墙摩擦角、填土内摩擦角、填土坡角对地震被动土压力的影响。与Mononobe-Okabe理论的拟静力法不同的是,用本方法得出了沿墙身地震被动土压力是非线性变化的结果,这更符合地震条件下土压力的变化规律。  相似文献   

5.
地基条件和墙高是影响挡土墙地震响应特征的重要因素。建立不同地基条件的仰斜式挡土墙有限元时程分析模型,以墙身外倾最大危险状态为最不利时刻,研究地基条件和墙高对挡墙动力响应及墙-土相互作用的影响特征,并以满足力学检算和墙身位移限值为出发点,提出同时考虑地基条件和地震峰值加速度PGA的仰斜式挡墙墙高控制建议。结果表明:岩质地基挡墙墙背动土压力沿墙高呈中部大、上下小的凸形分布,大震下土压力较中震时有小幅减小;基底反力呈墙踵为0、墙趾集中的三角形图式,且随PGA和墙高的增加踵部脱空趋势更为明显;土质地基挡墙因墙底地基土变形对墙后填土的牵连作用,填土跟随墙身运动的趋势加剧,墙背动土压力与PGA呈正相关并沿墙高近似呈线性分布,于墙底处最大;墙身往复摆动使踵趾端地基土体塑性变形较基底中部明显,基底反力峰值向中部转移;根据最不利时刻稳定性、承载力检算,考虑对墙身位移合理限制,提出地震区仰斜式挡墙的允许墙高在设防PGA不超过0.2g时为8 m, 0.4g大震下硬质岩地基挡墙可达8 m,软质岩地基挡墙不宜超过6 m,碎石土、砂质黏土地基挡墙不宜超过4 m。  相似文献   

6.
An overview of past and recent developments on the subject of seismic earth pressures on yielding, gravity-type walls, retaining cohesionless backfill, is first presented, focusing on available data on the issue of phase difference that develops between the peak values of wall inertia and seismic earth thrust increment. The results of a FEM parametric study are next presented regarding the dependence on the resulting dynamic earth thrust reduction – acting on the time of peak wall inertia – on backfill rigidity, wall height, and shaking characteristics. The reliability of the numerical analyses was verified by modeling centrifuge tests reported by Nakamura [24] and successfully comparing measured vs. computed behavior. The results of the parametric analyses indicate that the seismic active earth thrust, acting on the wall at the time of maximum wall inertia, is significantly reduced (compared to its peak value) with increasing shaking intensity of backfill, increasing wall displacements, increasing wall height, and decreasing backfill rigidity. No systematic dependence on the ratio of input motion frequency to the natural frequency of the backfill (f/f1) was observed. The above findings: (1) verify earlier experimental and numerical results, (2) explain the reported lack of damage to retaining walls under strong ground shaking, and (3) indicate the need for revising the pertinent provisions of current seismic codes. Graphs summarizing the results of the numerical analyses are presented which may be used as a guide for selecting the magnitude of seismic active earth thrust that needs to be taken into account in the design of the examined type of earth retaining walls.  相似文献   

7.
Knowledge of seismic active earth pressure behind rigid retaining wall is very important. Commonly used Mononobe–Okabe method considers pseudo-static approach, which gives the linear distribution of seismic earth force. In this paper, the pseudo-dynamic approach, which considers the effect of primary and shear wave propagations, is adopted to calculate the seismic active force. Considering the planar rupture surface, the effect of wide range of parameters like inclination of retaining wall, inclination of backfill surface, wall friction and soil friction angle, shear wave and primary wave velocity, horizontal and vertical seismic coefficients are taken into account to evaluate the seismic active force. Results are presented in terms of seismic coefficients in tabular form and variation of pressure along the depth.  相似文献   

8.
地震诱发的海啸对沿海围护结构的破坏具有强度大的特点。滨水挡土墙作为重要的围护结构,海啸与地震的联合作用极易造成其发生绕墙踵的被动破坏。采用条分法,将土楔体分割成无数平行于破裂面的刚性土条,并建立绕墙踵转动的挡墙与刚性土条之间的速度容许场。基于极限上限理论,依据外力做功功率等于其内能耗散功率,推导了地震加速度系数的表达式。与经典极限平衡理论相比,该方法考虑了挡墙的位移模式,且无需假设地震土压力的作用位置。分析了浪高与海平面高度之比,内摩擦角φ及墙土摩擦角δ对滨水挡土墙稳定性的影响。  相似文献   

9.
A stress plasticity solution is proposed for evaluating the gravitational and dynamic active earth pressures on cantilever retaining walls with long heel. The solution takes into account the friction angle of the soil, wall roughness, backfill inclination and horizontal and vertical seismic accelerations. It is validated by means of the comparison with both traditional limit equilibrium methods (e.g. Mononobe–Okabe equations) and static and pseudostatic numerical FLAC analyses. For numerical analyses the soil is modelled as an elasto-plastic non-dilatant medium obeying the Mohr–Coulomb yield criterion, while the wall is elastic. The solutions for the horizontal and vertical seismic coefficients are proposed, which allow one to determine the intensity of the active thrust and its inclination δ with respect to the horizontal. It is demonstrated that the latter also depends on the soil friction angle φ. The inclination in seismic conditions δE is greater than the one in static conditions, δS, usually adopted in both cases. As a matter of fact, since wall stability conditions improve with the increase of inclination δ, the present method gives solutions that are less onerous than traditional ones, producing less conservative wall designs. Finally pseudostatic results are compared with proper dynamic analyses (by FLAC code) performed utilising four Italian accelerometric time-histories as input ground motion.  相似文献   

10.
本文旨在讨论位于回填土场地上及回填土场地深挖基坑内的强震动观测仪所获得地震动是否是真实自由场地震动,若不是,其影响如何?结合回填土场地的强震动观测台站建设的实际情形,建立了回填土场地和回填土场地深挖基坑的有限元分析模型,基于集中质量显式动力有限元数值模拟方法,分析了回填土的波速和厚度、基坑尺寸对自由场地震动的影响.同时,提出了通过用重塑土置换回填土以降低回填土对自由场地震动影响的措施,并对重塑土置换回填土的效果进行了数值模拟分析.结果表明:回填土上和回填土深挖基坑内的地震动峰值和反应谱值与原始场地的均有明显的差异,随着回填土厚度和基坑深度的增加,其差异越大;通过重塑土置换回填土可以减小回填土对场地地震动的影响.本文所得关于回填土、基坑和重塑土的影响规律可为回填土场地上强震动观测结果的合理利用以及强震动观测台站建设提供依据.  相似文献   

11.
采用有限元有限差分方法,结合人工透射边界理论,研究局部坡地地形对地震动特性的影响,分析坡高、坡角对地形放大效应的影响.研究结果表明:坡地地形斜坡段各点反应谱谱比最大值沿坡高逐渐增大,坡脚点对地震动反应谱谱比呈缩小效应;坡底段各点反应谱谱比接近1;坡起平台段空间点受地形效应的影响较大;坡高和坡角对地形效应的影响较明显,当...  相似文献   

12.
高烈度地震区重力式挡土墙由于地基承载力不足导致墙身失稳是一种较常见震害类型。基于拟静力法原理,利用极限分析上限定理对地震作用下挡土墙地基极限承载力进行求解,通过典型算例分析了极限承载力随地震动峰值加速度的变化关系与机理,讨论了地基土强度参数对其变化趋势的影响,提出了同时考虑设防烈度和地基土性的挡土墙地基抗震容许承载力修正方法及相应修正系数取值建议。结果表明:设防烈度在9度及以内时,随着地震动峰值加速度增加,挡土墙地基极限承载力近似呈线性下降,下降速率与地基土黏聚力呈负相关性,而受内摩擦角的影响不显著;地震作用加剧挡土墙基底荷载倾斜与偏心导致地基破坏区缩减是造成极限承载力下降的主要原因;设防烈度大于7度时,挡土墙地基抗震容许承载力较天然工况下有所降低,8度和9度设防烈度对应的修正系数约为0.9和0.7。  相似文献   

13.
This study aims to realistically simulate the seismic responses of typical highway bridges in California with considerations of soil–structure interaction effects. The p‐y modeling approaches are developed and validated for embankments and pile foundations of bridges. The p‐y approach models the lateral and vertical foundation flexibility with distributed p‐y springs and associated t‐z and q‐z springs. Building upon the existing p‐y models for pile foundations, the study develops the nonlinear p‐y springs for embankments based on nonlinear 2D and 3D continuum finite element analysis under passive loading condition along both longitudinal and transverse directions. Closed‐form expressions are developed for two key parameters, the ultimate resistant force pult and the displacement y50, where 0.5pult is reached, of embankment p‐y models as functions of abutment geometry (wall width and height, embankment fill height, etc.) and soil material properties (wall‐soil friction angle, soil friction angle, and cohesion). In order to account for the kinematic and site responses, depth‐varying ground motions are derived and applied at the free‐end of p‐y springs, which reflects the amplified embankment crest motion. The modeling approach is applied to simulate the seismic responses of the Painter Street Bridge and validated through comparisons with the recorded responses during the 1992 Petrolia earthquake. It is demonstrated that the flexibility and motion amplification at end abutments are the most crucial modeling aspects. The developed p‐y models and the modeling approach can effectively predict the seismic responses of highway bridges. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

14.
在弹性力学和波动理论的基础上,运用时域和频域计算方法分析出平面SH波穿越地裂缝介质时的传播规律。通过引入地裂缝界面等效切向刚度等有关参数,对出平面波传播的频域及时域分析方法进行对比验证,分析地裂缝界面的等效切向刚度、入射波频率、入射角和裂缝面剪切强度对穿越地裂缝时出平面SH波的传播规律的影响。多个参数的交叉对比分析结果表明,等效切向刚度或入射角度越小,地裂缝界面的低通滤波效应越明显。裂缝面的剪切滑移导致透射波速在达到临界值时被截止。输入实际地震波时,随着透射系数的减小,透射波幅值减小不明显但波形变化较大;反射波幅值和波形将逐渐趋近入射波,但相位相对于入射波存在一定的滞后。为得到真实有效的波动传播规律,采用线性内插对波动时程数据进行处理,结果表明本文方法不会影响计算的精度。  相似文献   

15.
挡土墙地震反应非线性波动模拟   总被引:3,自引:0,他引:3  
本文运用解耦近场非线性波动数值模拟方法研究挡土墙地震反应,为反映墙土体系在地震作用下的位移机制,引入了Desai薄层单元模拟墙土间接触面,并采用双线型本构关系作为接触面单元和土体的非线性模型,在此基础上给出了解决P—SV问题的非线性显式有限元时域递推公式,为进一步发展非线性波动数值模拟技术提供了有益经验。为验证本文方法及适用性,将数值模拟结果与Zeng,X.和Madabhushi,X.P.G.等的离心机试验和弹塑性数值模拟结果进行对比。结果表明:墙土体系加速度、挡土墙顶底相对滑移、沉降和墙体倾角等同离心机试验模拟结果基本吻合,与弹塑性数值模拟结果相似。  相似文献   

16.
介绍场地时域分析基本理论和几种常见的阻尼矩阵确定方法,并基于有限差分方法,采用实际地震记录,考虑输入地震动强度和频谱特性,分别选择5种不同的瑞利阻尼矩阵形式,比较分析其对深厚场地时域动力反应的影响。结果表明:不同阻尼矩阵对加速度和反应谱均有影响,影响程度和输入地震动的频谱特性有关;当土层基频接近输入地震动卓越频率时,只根据土层基频确定阻尼矩阵是可行的,但当输入地震动卓越频率高于或远高于土层基频时,该方法会严重低估地表加速度峰值和反应谱谱值,时域分析中阻尼的确定应综合考虑土层特性和地震动频谱特性。  相似文献   

17.
基于应用透射人工边界条件的显式有限元法计算断层破碎带宽度及力学参数变化、地震动入射角变化时二维断层场地模型P波入射下地表地震动场的分布。结果表明:(1)低速度破碎带的存在导致整个场地都有P波转换为SV波的分量,且在断层破碎带的区域出现断层陷波;(2)低速度破碎带的存在使输入场地恒定的能量向破碎带集聚放大,随着破碎带宽度增大或其介质波速降低集聚放大效应增大;(3)场地放大效应是频率相关的,宽度较宽或介质波速较低的断层破碎带对输入地震动中较低的频率成份放大显著;(4)竖向断层破碎带能阻隔斜入射地震P波,随着入射角增加隔震效应更显著。  相似文献   

18.
This paper presents the effect of isolator and substructure properties as well as the frequency characteristics and intensity of the ground motion on the performance of seismic‐isolated bridges (SIBs) and examines some critical design clauses in the AASHTO Guide Specification for Seismic Isolation Design. For this purpose, a parametric study, involving more than 800 non‐linear time history analyses of simplified structural models representative of typical SIBs, is conducted. The results from the parametric study are then used to derive important design recommendations and conclusions that may be used by bridge engineers to arrive to a more sound and economical design of SIBs. It is found that the SIB response is a function of the peak ground acceleration to peak ground velocity ratio of the ground motion. Thus, the choice of the seismic ground motion according to the characteristics of the bridge site is crucial for a correct design of the SIB. It is also found that the characteristic strength of the isolator may be chosen based on the intensity and frequency characteristics of the ground motion. Furthermore, the isolator post‐elastic stiffness is found to have a notable effect on the response of SIBs. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

19.
A systematic study is made of the effects of seismic impacts between the base of an isolated building and the surrounding retaining wall. The analysis is performed without using gap elements or assuming values of the coefficient of restitution and the duration of impact. The analysis captures the effects of wave travel along the height of the building and of the associated energy loss. It poses no numerical difficulties. Results show that for elastic systems the base shear generated by impacts can be higher than the weight of the building; base shear increases with increase in the stiffness of the retaining wall, stiffness of the building and the mass of the base mat. A significant fraction of the initial kinetic energy of the system is lost by impacts; energy loss increases with increase in the stiffness of the retaining wall, system damping and mass of the base mat. © 1997 John Wiley & Sons, Ltd.  相似文献   

20.
This paper examines the distribution of seismic drift demands in multi-storey steel moment frames designed to the provisions of Eurocode 8, with due account of the frequency content of ground motion. After providing an overview of current design rules, selected results from a detailed parametric investigation into inelastic drift demands are presented and discussed. The study includes extensive incremental dynamic analyses covering a wide range of structural characteristics and a large suite of ground motion records. The mean period is adopted in this work as a measure of the frequency content of ground motion. Prediction models for maximum global and inter-storey drift demands are presented and shown to be primarily affected by the fundamental-to-mean period ratio and the behaviour factor. Particular attention is given in this paper to the influence of the relative storey stiffness ratio on the distribution of drift demands over the height of the structure. In order to achieve a comparatively uniform drift distribution, a target relative storey stiffness ratio, incorporating the structural and ground motion characteristics, is proposed for design purposes. Finally, the implications of the findings on typical design procedures are highlighted, and possible improvements in codified guidance are discussed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号