首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 359 毫秒
1.
The dissolution of pyrite is of interest in the formation of acid mine drainage and is a complex electrochemical process. Being able to measure the rate of dissolution of particular pyrite samples under particular conditions is important for describing and predicting rates of AMD generation. Electrochemical techniques offer the promise of performing such measurements rapidly and with small samples. The oxidation of pyrite and the reduction of Fe3+ ions and/or O2 half reactions involved in the pyrite dissolution process were investigated by cyclic voltammetry and steady-state voltammetry using three pyrite materials formed in both sedimentary and hydrothermal environments. For each sample, two kinds of pyrite working electrodes (conventional constructed compact solid electrode, and carbon paste electrode constructed from fine-grained pyrite particles) were employed. Results indicated that for both the hydrothermal and sedimentary pyrite samples the oxidation and reduction half reactions involved in dissolution were governed by charge transfer processes, suggesting that hydrothermal and sedimentary pyrites obey the same dissolution mechanism despite their different formation mechanisms. In addition, the results showed that it is feasible to use a C paste electrode constructed from fine-grained or powdered pyrite to study the pyrite dissolution process electrochemically and to derive approximate rate expressions from the electrochemical data.  相似文献   

2.
Synthetic pyrite crystals doped with As, Co, or Ni, undoped pyrite, and natural arsenian pyrite from Leadville, Colorado were investigated with electrochemical techniques and solid-state measurements of semiconducting properties to determine the effect of impurity content on pyrite’s oxidation behavior. Potential step experiments, cyclic voltammetry, and AC voltammetry were performed in a standard three-electrode electrochemical cell setup. A pH 1.78 sulfuric acid solution containing 1 mM ferric iron, open to atmospheric oxygen, was chosen to approximate water affected by acid drainage. Van der Pauw/Hall effect measurements determined resistivity, carrier concentration and carrier mobility.The anodic dissolution of pyrite and the reduction of ferric iron half-reactions are taken as proxies for natural pyrite oxidation. Pyrite containing no impurities is least reactive. Pyrite with As is more reactive than pyrite with either Ni or Co despite lower dopant concentration. As, Co, and Ni impurities introduce bulk defect states at different energy levels within the band gap. Higher reactivity of impure pyrite suggests that introduced defect levels lead to higher density of occupied surface states at the solid-solution interface and increased metallic behavior. The current density generated from potential step experiments increased with increasing As concentration. The higher reactivity of As-doped pyrite may be related to p-type conductivity and corrosion by holes. The results of this study suggest that considering the impurity content of pyrite in mining waste may lead to more accurate risk assessment of acid producing potential.  相似文献   

3.
金属矿物的反应动力学与地球化学意义   总被引：8，自引：0，他引：8  
张生 《地学前缘》1999,6(2):351-360
概述了动力学实验的技术方法和金属矿物的反应动力学研究进展。动力学实验使用的三种基本化学反应装置是间歇反应器（ＢＲ）、活塞流反应器（ＰＦＲ）和混合流反应器（ＭＦＲ）,确定速率定律的数学方法包括积分法、微分法和混合法,以微分法中的初始速率法应用最广。目前主要研究了水溶液中黄铁矿氧化、黄铁矿和黄铜矿形成、晶质铀矿和磁铁矿溶解的速率定律和反应机理,发现：（１）酸性溶液中黄铁矿的氧化速率对Ｆｅ３＋和Ｏ２浓度呈分数依赖并受表面反应的控制;（２）低于３００℃时黄铁矿不能从溶液中直接成核,而需初始地通过ＦｅＳ先驱物的硫化生成,ＦｅＳ与Ｈ２Ｓ反应形成黄铁矿的速率方程为二级;（３）磁黄铁矿或黄铁矿与Ｃｕ２＋反应均可形成黄铜矿,前者经历了一系列准稳的Ｃｕ Ｆｅ硫化物的中间物,后者的速率方程为表观一级并受表面反应的控制;（４）酸性ｐＨ时磁铁矿的非线性溶解行为可采用表面反应扩散输运耦合的收缩核模型（ＳＣＭ）来描述。有关动力学实验成果完善和深化了对矿床中黄铁矿、黄铜矿的形成机理和风化壳中磁铁矿的稳定性等方面的认识。将来的实验研究将向更多的金属矿物和高温高压领域发展。  相似文献   

4.
The abiotic oxidative dissolution behaviors of eight natural pyrite samples, five sedimentary and three hydrothermal, from various geological environments were compared under oxic conditions at pH 3 and 6 in a highly controlled batch reactor dissolution system. The three sedimentary pyrite samples associated with coal had greater specific surface areas and also exhibited greater apparent dissolution rates and extent than the other two sedimentary and three hydrothermal samples under both pH conditions. However, after normalizing for surface area, the dissolution rate constants for the different pyrite samples were similar; the greatest difference was between the two non-coal sedimentary pyrite samples. Pyrite morphology and the presence of trace metals could contribute to the differences in dissolution behavior as reflected in the normalized dissolution rates. The sulfur:iron ratio observed in the aqueous solution at pH 3 increased with time, but was always less than 2.0 (predicted from the stoichiometry of dissolution) for all the pyrite samples during the 24-h experimental duration. This can be explained by the disproportionation dissociation of thiosulfate, an initial product of pyrite dissolution, to elemental sulfur and sulfate which does not occur in a 1:1 ratio. The results of this work indicate the importance of extracting and using the specific pyrite(s) relevant to particular mining areas in order to understand pyrite dissolution rates and the influence of environmental conditions on those rates.  相似文献   

5.
Geochemical reactive transport modeling was coupled to bench-scale leaching experiments to investigate and verify the mobilization of geogenic arsenic (As) under a range of redox conditions from an arsenic-rich pyrite bearing limestone aquifer. Modeling and experimental observations showed similar results and confirmed the following: (1) native groundwater and aquifer matrix, including pyrite, were in chemical equilibrium, thus preventing the release of As due to pyrite dissolution under ambient conditions; (2) mixing of oxygen- and nitrate-rich surface water with oxygen-depleted native groundwater changed the redox conditions and promoted the dissolution of pyrite, and (3) the behavior of As along a flow path was controlled by a complex series of interconnected reactions. This included the oxidative dissolution of pyrite and simultaneous sorption of As onto neo-formed hydrous ferric oxides (HFO), followed by the reductive dissolution of HFO and secondary release of adsorbed As under reducing conditions. Arsenic contamination of drinking water in these systems is thus controlled by the re-equilibration of the system to more reducing conditions rather than a purely oxidative process.  相似文献   

6.
《Applied Geochemistry》2001,16(7-8):803-819
Sulfide mineral oxidation, primarily pyrite and pyrrhotite, generates acid mine drainage during weathering. Successful management of acid generating wastes entails the suppression of the initiation of oxidation reactions. The reactivity of pyrite depends on ore mineralogy, including the effects of associated sulfide impurities. The electrochemical surface characterization study using cyclic voltammetry with carbon paste electrodes containing minerals particles (CPE-Mineral) is an effective tool for demonstrating how the various mineral characteristics work together to influence the overall reactivity of the mineral. This study was supported by chemical, mineralogical and leachate chemistry data. The results show that the presence of other sulfides in contact with pyrite at the beginning of the weathering process is the most important parameter affecting pyrite reactivity, which is likely to be oxidized and passivated. In more advanced stages of leaching, mineral coatings which passivate the pyrite surfaces tend to play the most important role in defining the reactivity of pyrite. The electrochemical response of pyritic samples in conjunction with the evolution of the chemical quality of the leach solution in the simple experimental device here used, could then provide valuable information on acid mine drainage generation.  相似文献   

7.
Further knowledge as to the nature of the structure of a terrestrial sample of troilite, FeS [stoichiometric iron(II) sulfide] is revealed by a combination of XPS studies and dissolution studies in acid. The XPS analysis of a pristine troilite surface (the sample being cleaved under high vacuum) is compared to that of a surface polished in an inert atmosphere and a surface after reaction in deoxygenated acid. Further comparison is made with polished and acid-reacted surfaces of pyrrhotite (Fe1-xS) and pyrite (FeS2). The pristine troilite S2p spectrum comprises mainly monosulfide 161.1 eV, within the reported range of monosulfide, together with evidence of an unsatisfied monosulfide surface state arising from S-Fe bond rupture. Small, higher oxidation state sulfur contributions, including a disulfide-like state are also present, which suggest the presence of defects due to some nonstoichiometry. The dissolution studies showed that the troilite, in addition to dissolving in acid as an ionic solid to produce H2S, also exhibits some oxidation of sulfur in the surface layers. In addition, a study of the dissolution behavior of troilite under the influence of cathodic applied potential supported the existence of a proportion of the sulfur within troilite needing reduction before dissolution forming HS− or H2S can occur. A significant increase in the dissolution rate was observed with application of −105 mV (SHE), but further stepped decreases in potential to −405 mV and −705 mV resulted in a decreased rate of dissolution, a response typical of an ionic solid. The results of the studies emphasise the viewing of iron(II) sulfides as a continuum. Pyrrhotite has been reported previously to dissolve in acid both oxidatively (like pyrite) and nonoxidatively (like troilite) on the same surface. Dissolution studies using troilite, in Ar-purged acid, indicate that dissolution of this material may not be uniformly nonoxidative. XPS evidence of restructuring of the surface of troilite to pyrrhotite and the surface of pyrrhotite towards a FeS2 type structure, after exposure to Ar-purged acid, is presented.  相似文献   

8.
The kinetics of abiotic redox reactions induced by hydrogen are poorly documented although it represents a growing area of interest in terms of both nuclear waste storage assessment and the comprehensive study of hydrogen-rich fluid in mid-ocean ridge hydrothermal systems. We present an experimental kinetics study of pyrite reduction into pyrrhotite under significant H2 pressure and mid-hydrothermal conditions. We describe the mechanism and kinetic behavior of this reaction by combining textural and solution analyses under various conditions of temperature, pyrite particles size, H2 pressure and pH. When pH is controlled by calcite, the reaction presents all the characteristics of a coupled dissolution-precipitation mechanism occurring at the pyrite-pyrrhotite interface. By considering the chemical affinity of the coupled reaction as a function of reaction extent, we demonstrate that the spatial coupling is induced both by pyrite as a substrate for pyrrhotite nucleation and by the role of fluid chemistry at the reaction front. Far from equilibrium with respect to pyrite, the kinetics of sulfide production associated with the reaction are linearly related to the square root of time with an activation energy of 53 kJ/mol. This value is higher than what is expected for a diffusion-controlled kinetic regime. We suggest that the reaction rate is controlled both by pyrite reductive dissolution and by sulfide diffusion through the porous pyrrhotite microstructure. We provide a simple sulfide production-rate expression on the basis of our measured rate constants that can be used in geochemical modeling to further evaluate the impact of hydrogen on pyrite under nuclear waste disposal conditions.  相似文献   

9.
When galvanic interactions between pyrite and chalcopyrite occur in solution, pyrite, with the higher rest potential, acts as a cathode and is protected whereas chalcopyrite, with the lower rest potential, acts as an anode and its oxidation is increased. In this work a three-electrode system was used to investigate the corrosion current density and mixed potential of a galvanic cell comprising a pyrite cathode and a chalcopyrite anode in a flowing system. The results showed that with increasing concentration of ferric ion in the solution, with increasing acidity, and with increasing flow rate of the solution, the corrosion current density increased and the mixed potential of the galvanic cell became more positive. These experimental results are of direct significance to the control of environmental pollution in mining activity. By using the galvanic model, mixed potential theory, and the Butler–Volmer equation, the experimental results were explained theoretically.  相似文献   

10.
The determination of trace element release from geologic materials, such as oil shale and coal overburden, is important for proper solid waste management planning. The objective of this study was to determine a correlation between trace element residency and concentration to trace element release using the following methods: (1) sequential selective dissolution for determining trace element residencies, (2) toxicity characteristic leaching procedure (TCLP), and (3) humidity cell weathering study simulating maximum trace element release. Two eastern oil shales were used, a New albany shale that contains 4.6 percent pyrite, and a Chattanooga shale that contains 1.5 percent pyrite. Each shale was analyzed for elemental concentrations by soluble, adsorbed, organic, carbonate, and sulfide phases. All leachates were analyzed to determine total trace element concentrations. The results of the selective dissolution studies show that each trace element has a unique distribution between the various phases. Thus, it is possible to predict trace element release based on trace element residency. The TCLP results show that this method is suitable for assessing soluble trace element release but does not realistically assess potential hazards. The results of the humidity cell studies do demonstrate a more reasonable method for predicting trace element release and potential water quality hazards. The humidity cell methods, however, require months to obtain the required data with a large number of analytical measurements. When the selective dissolution data are compared to the trace element concentrations in the TCLP and humidity cell leachates, it is shown that leachate concentrations are predicted by the selective dissolution data. Therefore, selective dissolution may represent a rapid method to assess trace element release associated with acid mine drainage.  相似文献   

11.
As a result of the collapse of a mine tailing dam, a large extension of the Guadiamar valley was covered with a layer of pyritic sludge. Despite the removal of most of the sludge, a small amount remained in the soil, constituting a potential risk of water contamination. The kinetics of the sludge oxidation was studied by means of laboratory flow-through experiments at different pH and oxygen pressures. The sludge is composed mainly of pyrite (76%), together with quartz, gypsum, clays, and sulphides of zinc, copper, and lead. Trace elements, such as arsenic and cadmium, also constitute a potential source of pollution. The sludge is fine grained (median of 12 μm) and exhibits a large surface (BET area of 1.4±0.2 m2 g−1).

The dissolution rate law of sludge obtained is r=10−6.1(±0.3) [O2(aq)]0.41(±0.04) aH+0.09(±0.06) gsludge m−2 s−1 (22 °C, pH=2.5–4.7). The dissolution rate law of pyrite obtained is r=10−7.8(±0.3) [O2(aq)]0.50(±0.04) aH+0.10(±0.08) mol m−2 s−1 (22 °C, pH=2.5–4.7). Under the same experimental conditions, sphalerite dissolved faster than pyrite but chalcopyrite dissolves at a rate similar to that of pyrite. No clear dependence on pH or oxygen pressure was observed. Only galena dissolution seemed to be promoted by proton activity. Arsenic and antimony were released consistently with sulphate, except at low pH conditions under which they were released faster, suggesting that additional sources other than pyrite such as arsenopyrite could be present in the sludge. Cobalt dissolved congruently with pyrite, but Tl and Cd seemed to be related to galena and sphalerite, respectively.

A mechanism for pyrite dissolution where the rate-limiting step is the surface oxidation of sulphide to sulphate after the adsorption of O2 onto pyrite surface is proposed.  相似文献   


12.
黄铁矿表面溶解——不容忽视的研究领域   总被引：2，自引：0，他引：2  
矿物表面反应存在于结晶、溶解、成岩成矿、蚀变和风化等一系列地质过程中,在环境科学和材料科学也有着重要的应用,因此,表面矿物学已成为国际地学研究的热点。本文概括了近年来黄铁矿等硫化物表面反应的研究进展,指出了黄铁矿的表面溶解研究存在的问题,并重点阐述了黄铁矿表面溶解研究在诸多方面的重要意义,包括黄铁矿表面溶解研究的理论意义、黄铁矿的表面溶解对矿山环境评价的意义、尾矿堆中绝大多数黄铁矿处于酸性还原环境、黄铁矿表面溶解控制着海洋中硫的循环。本文还报道了笔者通过实验所获得的黄铁矿溶解反应动力学的初步研究结果。  相似文献   

13.
The mobility of subsurface arsenic is controlled by sorption, precipitation, and dissolution processes that are tied directly to coupled redox reactions with more abundant, but spatially and temporally variable, iron and sulfur species. Adjacent to the site of a former pesticide manufacturing facility near San Francisco Bay (California, USA), soil and groundwater arsenic concentrations are elevated in sediments near the prior source, but decrease to background levels downgradient where shallow groundwater mixes with infiltrating tidal waters at the plume periphery, which has not migrated appreciably in over two decades of monitoring. We used synchrotron X-ray absorption spectroscopy, together with supporting characterizations and sequential chemical extractions, to directly determine the oxidation state of arsenic and iron as a function of depth in sediments from cores recovered from the unsaturated and saturated zones of a shallow aquifer (to 3.5 m below the surface). Arsenic oxidation state and local bonding in sediments, as As-sulfide, As(III)-oxide, or As(V)-oxide, were related to lithologic redox horizons and depth to groundwater. Based on arsenic and iron speciation, three subsurface zones were identified: (i) a shallow reduced zone in which sulfide phases were found in either the arsenic spectra (realgar-like or orpiment-like local structure), the iron spectra (presence of pyrite), or both, with and without As(III) or As(V) coordinated by oxygen; (ii) a middle transitional zone with mixed arsenic oxidation states (As(III)–O and As(V)–O) but no evidence for sulfide phases in either the arsenic or iron spectra; and (iii) a lower oxidized zone in the saturated freshwater aquifer in which sediments contained only oxidized As(V) and Fe(III) in labile (non-detrital) phases. The zone of transition between the presence and absence of sulfide phases corresponded to the approximate seasonal fluctuation in water level associated with shallow groundwater in the sand-dominated, lower oxic zone. Total sediment arsenic concentrations showed a minimum in the transition zone and an increase in the oxic zone, particularly in core samples nearest the former source. Equilibrium and reaction progress modeling of aqueous-sediment reactions in response to decreasing oxidation potential were used to illustrate the dynamics of arsenic uptake and release in the shallow subsurface. Arsenic attenuation was controlled by two mechanisms, precipitation as sulfide phases under sulfate-reducing conditions in the unsaturated zone, and adsorption of oxidized arsenic to iron hydroxide phases under oxidizing conditions in saturated groundwaters. This study demonstrates that both realgar-type and orpiment-type phases can form in sulfate-reducing sediments at ambient temperatures, with realgar predicted as the thermodynamically stable phase in the presence of pyrite and As(III) under more reduced conditions than orpiment. Field and modeling results indicate that the potential for release of arsenite to solution is maximized in the transition between sulfate-reduced and iron-oxidized conditions when concentrations of labile iron are low relative to arsenic, pH-controlled arsenic sorption is the primary attenuation mechanism, and mixed Fe(II,III)-oxide phases do not form and generate new sorption sites.  相似文献   

14.
天然饱水条件下黄铁矿氧化过程的热力学探讨   总被引：1，自引：0，他引：1  
本文从化学热力学角度讨论了黄铁矿在低温低压条件下通过化学作用氧化的历程,指出了决定黄铁矿氧化速率的步骤是黄铁矿的溶解作用,并对一实际水样进行了化学反应的平衡分析  相似文献   

15.
Field, petrographic and stable isotopic evidence indicate the former presence of widespread evaporites in the Neoarchaean Campbellrand Subgroup of South Africa. Calcitization of the vanished but once laterally-extensive evaporites was apparently driven by bacterial sulphate reduction of solid sulphate in association with organic diagenesis and pyrite precipitation within platform-wide microbialites and sapropels. This counters current interpretations that much of the calcite was precipitated directly on the seafloor or in primary voids in open marine conditions controlled by regional seawater chemistry. Rather, large-scale microbial mediation of ambient waters across a shallow to emergent platform raised carbonate alkalinity and removed kinetic inhibitors to carbonate formation.The low preservation potential of Precambrian solid sulphate is related in part to bacterial sulphate reduction within the microbially-dominated ecosystems of which cyanobacteria were a major component. Evidence for the former presence of solid sulphate in shallow Neoarchaean seas includes pseudomorphs after selenite, also recorded from the contemporaneous Carawine Dolomite of Australia, together with rock fabrics and textures typical of evaporite dissolution. Importantly, sulphur isotopes of pyrite samples from the Cambellrand carbonates show a wide range of values indicating biogenic fractionation of sulphate, a signature also seen in the Neoarchaean Belingwe Greenstone Belt of Zimbabwe, and the Mt McRae and Jeerinah shales of Western Australia.Mass microbial colonization across extensive Neoarchaean epeiric seas witnessed the microbiogeochemical transformation of the Earth’s hydrosphere, atmosphere and biosphere. The consequences for a reducing ocean would be the progressive oxidation of the major dissolved species in surface seawater, most notably of reduced sulphur and iron. Cyanobacterial photosynthetic oxidation of surface seawater drove formation of aqueous sulphate and permitted the precipitation of extensive evaporites in restricted basins, perhaps beginning the process of ridding the oceans of reduced sulphur. The first dramatic explosion of carbonate precipitation can be related to intense bacterial sulphate reduction in association with anoxic organic diagenesis and pyrite formation within the decaying interiors of microbialites and in sapropels.  相似文献   

16.
The anodic and cathodic behaviour of pyrite with clay and different carbon coatings of activated carbon, graphite and carbonaceous matter in cyanide medium was investigated using the potentiodynamic method. The presence of clay coating did not change the polarisation curve appearance for either the anodic oxidation of pyrite or the cathodic reduction of oxygen or the potential of the current plateau, but only decreased the plateau current especially at a higher coating thickness. The presence of the carbon coatings marginally shifted the rest potential for pyrite to a more anodic position and slightly changed the polarisation curve appearance for pyrite oxidation. The current density for pyrite oxidation largely increased in the presence of the carbon coatings, the potential at the plateau shifted to more cathodic positions, and the plateau width became smaller. These effects became more noticeable at a higher coating thickness. The activated carbon, graphite and carbonaceous matter coatings performed similarly in affecting pyrite oxidation at a similar thickness. The carbon coatings significantly increased the limiting current densities for oxygen reduction on pyrite, and the limiting current plateau became steeper at a higher coating thickness. The carbon coatings increased the limiting current density for oxygen reduction to a similar extent at a low coating thickness, but increased to varied extents at a higher coating thickness. The carbon coatings also greatly increased the cathodic current density for gold reduction on pyrite. The enhancement of pyrite oxidation and oxygen or gold reduction on pyrite by the carbon coatings was likely attributed to the electrochemical interaction between pyrite and the carbon materials with electron-rich surfaces and high conductivity. The presence of the carbon coatings significantly increased the oxidation of pyrite in aerated cyanide solutions and the preg-robbing of pyrite especially at a higher coating thickness.  相似文献   

17.
地球系统中各种矿物相的物理化学反应大多是从矿物表面或界面开始的。要揭示矿物表面反应性的本质,就需要从控制其反应性的表面结构入手。由于实验条件的限制,绝大多数关于矿物表面物理化学性质的研究主要采用粉晶作为研究对象。尽管粉晶方法在研究诸如硅酸盐、碳酸盐溶解和沉淀结晶等过程中被普遍采用,但这种基于矿物粉晶的研究方法还是有一定的不足。因为形成粉晶的破碎研磨过程会导致晶体高能面的出现,高能面所具有的高活性可能会加速其反应过程,应用于地球化学反应的计算结果就可能高估了实际的地球化学反应速率。本研究以黄铁矿表面氧化反应的晶面差异性为例,从晶面结构制约反应性的角度出发,重新审视了黄铁矿氧化的相关问题,弥补了传统"粉晶研究"中对黄铁矿氧化速率和氧化机理认识的缺陷。黄铁矿宽范围的氧化速率实测值很可能是由不同晶面间较大的反应性差异导致;水在黄铁矿的氧化过程中同时扮演着传递电子的催化剂和反应物的角色,也是黄铁矿氧化反应速控步(rate-limiting step)的核心物质。这些认识首次明确了黄铁矿不同晶面反应性差异的重要性,并提示我们应将传统表面矿物学的研究推向更为精确的晶面矿物学水平。这一从晶面角度考察发生在矿物表面的地球化学反应的研究方法可为构建更为精确的地球化学模型提供理论基础。  相似文献   

18.
Pyrite samples synthesized with As, Co, or Ni impurities and without added impurities were oxidized in batch and mixed flow-through reactors in the presence of 1 mM ferric iron, at pH 2. Six samples from each dopant population were used to provide a statistically robust comparison; two natural samples from Leadville, CO (major impurities Pb, As, Bi, Ag, Zn) and Elba, Italy (Co, As) were also included. In each experiment, three reaction progress variables were monitored: ferric iron, ferrous iron, and sulfate. The pyrite samples with impurities have average oxidation rates that are faster than the undoped samples, with As- and Co-doped pyrite having the highest rates. As, Co, and Ni were released to solution in accordance with their concentrations in the solid samples. As concentrations in the batch reactor experiments tended to remain constant, in contrast to Co and Ni, which increased over time. Initial rates, calculated from the batch reactor experiments, were faster than the steady-state rates calculated from the mixed flow-through reactor experiments. Apparent rates calculated using sulfate were faster than apparent rates calculated using ferric and ferrous iron, reflecting oxidation of ferrous iron in solution by dissolved oxygen. The results imply that impurities in pyrite do contribute to its reactivity, in agreement with studies using electrochemical methods. Oxidation rate differences among pyrite samples with different impurities are probably too small to warrant explicit consideration in environmental modeling applications, but are important to understanding pyrite oxidation mechanisms and semiconducting properties.  相似文献   

19.
This paper deals with bacterial leaching of copper dust emanating from furnaces at Sarcheshmeh copper complex. Regarding the considerable amount of acid leachable copper, a sulphuric acid leaching process was performed prior to bacterial leaching. Some shake flask and then bioreactor tests were conducted using a mixed culture of Acidithiobacilli and the effect of significant parameters such as culture medium, pulp density and bacterial inoculation rate were investigated. By increasing the pulp density because of higher toxicity and shear stress much more microorganisms and richer nutrient medium were needed. Favoured conditions that governed the agitated bioreactors caused a remarkable promotion in metal dissolution rate in comparison with shake flask. Copper recovery by bacterial leaching in shaking flasks and chemical leaching after 22 d were 87% and 38%, respectively. At the same condition, the maximum copper recovery in bioreactor was 91% within 6.5 d.  相似文献   

20.
Characterisation of mine waste rock with respect to acid generation potential is a necessary part of routine mine operations, so that environmentally benign waste rock stacks can be constructed for permanent storage. Standard static characterisation techniques, such as acid neutralisation capacity (ANC), maximum potential acidity, and associated acid–base accounting, require laboratory tests that can be difficult to obtain rapidly at remote mine sites. We show that a combination of paste pH and a simple portable carbonate dissolution test, both techniques that can be done in the field in a 15 min time-frame, is useful for distinguishing rocks that are potentially acid-forming from those that are acid-neutralising. Use of these techniques could allow characterisation of mine wastes at the metre scale during mine excavation operations. Our application of these techniques to pyrite-bearing (total S = 1–4 wt%) but variably calcareous coal mine overburden shows that there is a strong correlation between the portable carbonate dissolution technique and laboratory-determined ANC measurements (range of 0–10 wt% calcite equivalent). Paste pH measurements on the same rocks are bimodal, with high-sulphur, low-calcite rocks yielding pH near 3 after 10 min, whereas high-ANC rocks yield paste pH of 7–8. In our coal mine example, the field tests were most effective when used in conjunction with stratigraphy. However, the same field tests have potential for routine use in any mine in which distinction of acid-generating rocks from acid-neutralising rocks is required. Calibration of field-based acid–base accounting characteristics of the rocks with laboratory-based static and/or kinetic tests is still necessary.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号