首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 546 毫秒
1.
Deep saline aquifers still remain a significant option for the disposal of large amounts of CO2 from the atmosphere as a means of mitigating global climate change. The small scale Carbon Capture and Sequestration demonstration project in Ordos Basin, China, operated by the Shenhua Group, is the only one of its kind in Asia, to put the multilayer injection technology into practice. This paper aims at studying the influence of temperature, injection rate and horizontal boundary effects on CO2 plume transport in saline formation layers at different depths and thicknesses, focusing on the variations in CO2 gas saturation and mass fraction of dissolved CO2 in the formation of brine in the plume’s radial three-dimensional field around the injection point, and interlayer communication between the aquifer and its confining beds of relatively lower permeability. The study uses the ECO2N module of TOUGH2 to simulate flow and pressure configurations in response to small-scale CO2 injection into multilayer saline aquifers. The modelling domain involves a complex multilayer reservoir–caprock system, comprising of a sequence of sandstone aquifers and sealing units of mudstone and siltstone layers extending from the Permian Shanxi to the Upper Triassic Liujiagou formation systems in the Ordos Basin. Simulation results indicate that CO2 injected for storage into deep saline aquifers cause a significant pressure perturbation in the geological system that may require a long duration in the post-injection period to establish new pressure equilibrium. The multilayer simultaneous injection scheme exhibits mutual interference with the intervening sealing layers, especially when the injection layers are very close to each other and the corresponding sealing layers are thin. The study further reveals that injection rate and temperature are the most significant factors for determining the lateral and vertical extent that the CO2 plume reaches and which phase and amount will exist at a particular time during and after the injection. In general, a large number of factors may influence the CO2–water fluid flow system considering the complexity in the real geologic sequence and structural configurations. Therefore, optimization of a CO2 injection scheme still requires pursuance of further studies.  相似文献   

2.
Very limited investigations have been done on the numerical simulation of carbon dioxide (CO2) migration in sandstone aquifers taking consideration of the interactions between fluid flow and rock stress. Based on the poroelasticity theory and multiphase flow theory, this study establishes a mathematical model to describe CO2 migration, coupling the flow and stress fields. Both finite difference method (FDM) and finite element method (FEM) were used to discretize the mathematical model and generate a numerical model. A case study was carried out using the numerical model on the Jiangling sandstone aquifer in the Jianghan basin, China. The rock mechanics parameters of reservoir and overlying strata of Jiangling depression were obtained by triaxial tests. A two-dimensional model was then built to simulate carbon dioxide migration in the sandstone aquifer. The numerical simulation analyzes the carbon dioxide migration distribution rule with and without considering capillary pressure. Time-dependent migration of CO2 in the sandstone aquifer was analyzed, and the result from the coupled model was compared with that from a traditional non-coupled model. The calculation result indicates a good consistency between the coupled model and the non-coupled model. At the injection point, the CO2 saturation given by the coupled model is 15.39 % higher than that given by the non-coupled model; while the pore pressure given by the coupled model is 4.8 % lower than that given by the non-coupled model. Therefore, it is necessary to consider the coupling of flow and stress fields while simulating CO2 migration for CO2 disposal in sandstone aquifers. The result from the coupled model was also sensitized to several parameters including reservoir permeability, porosity, and CO2 injection rate. Sensitivity analyses show that CO2 saturation is increased non-linearly with CO2 injection rate and decreased non-linearly with reservoir porosity. Pore pressure is decreased non-linearly with reservoir porosity and permeability, and increased non-linearly with CO2 injection rate. When the capillary pressure was considered, the computed gas saturation of carbon dioxide was increased by 10.75 % and the pore pressure was reduced by 0.615 %.  相似文献   

3.
The feasibility of CO2 storage and enhanced gas recovery (EGR) effects in the mature Altmark natural gas field in Central Germany has been studied in this paper. The investigations were comprehensive and comprise the characterization of the litho- and diagenetic facies, mineral content, geochemical composition, the petrophysical properties of the reservoir rocks with respect to their potential reactivity to CO2 as well as reservoir simulation studies to evaluate the CO2 wellbore injectivity and displacement efficiency of the residual gas by the injected CO2. The Rotliegend sediments of the Altmark pilot injection area exhibit distinct mineralogical, geochemical, and petrophysical features related to litho- and diagenetic facies types. The reservoir rock reactivity to CO2 has been studied in autoclave experiments and associated effects on two-phase transport properties have been examined by means of routine and special core analysis before and after the laboratory runs. Dissolution of calcite and anhydrite during the short-term treatments leading to the enhancements of permeability and porosity as well as stabilization of the water saturation relevant for CO2 injection have been observed. Numerical simulation of the injection process and EGR effects in a sector of the Altmark field coupled with a wellbore model revealed the possibility of injecting the CO2 gas at temperatures as low as 10 °C and pressures around 40 bar achieving effective inflow in the reservoir without phase transition in the wellbore. The small ratio of injected CO2 volume versus reservoir volume indicated no significant EGR effects. However, the retention and storage capacity of CO2 will be maximized. The migration/extension of CO2 varies as a function of heterogeneity both in the layers and in the reservoir. The investigation of CO2 extension and pressure propagation suggested no breakthrough of CO2 at the prospective production well during the 3-year injection period studied.  相似文献   

4.
In CO2 geological storage (CGS) context, the evolution of the caprock sealing capacity has received increasing attention, particularly on a geological time span (thousands of years). At this time scale, geochemical reactions may enhance or weaken the caprock quality. It is widely recognized that, for the reservoir, geological heterogeneities affect the concentration and spatial distribution of CO2, and then affect the extent of gas–water–rock interactions, which in turn alters the hydrogeological properties of the reservoir. However, much less attention of these effects has been paid to the caprock. In this study, we presented and applied a novel approach to evaluate the effects of permeability and porosity heterogeneities on the alteration of minerals, the associated evolution of the caprock sealing efficiency and the containment of supercritical CO2 (scCO2) within the caprock. Even though this is a generic study, several conditions and parameters such as pressure, permeability, and mineral composition, were extracted from a caprock layer of the Shiqianfeng Formation in the Ordos Basin demonstration site in China. For the sake of simplification, a 2-dimensional model was designed to represent the caprock domain. We firstly generated an appropriate heterogeneous random field of permeability with the average permeability taken from the uppermost mudstone layer of the Shiqianfeng Formation, and then the heterogeneity in porosity was incorporated using a joint normal distribution method based on the available data. Homogeneous mineral compositions of the reservoir and caprock were used in all simulations. Simulations of three cases were performed, including a homogeneous case, a case with only permeability heterogeneity and a case with both permeability and porosity heterogeneities. The results demonstrate dramatic influences of permeability and porosity heterogeneities on the migration of scCO2 within the caprock, the alteration of minerals, and therefore the evolution of the caprock sealing quality. Specific to the data used in this study, hydrogeological heterogeneities facilitated the overall penetration of scCO2 within the caprock and promoted the alteration of minerals, thereby weakening the caprock sealing efficiency over the simulation time.  相似文献   

5.
This work studied the effect of completion techniques and reservoir heterogeneity on CO2 storage and injectivity in saline aquifers using a compositional reservoir simulator, CMG-GEM. Two reservoir models were built based on the published data to represent a deep saline aquifer and a shallow aquifer. The effect of various completion conditions on CO2 storage was then discussed, including partial perforation of the reservoir net pay (partial completion), well geometry, orientation, location, and length. The heterogeneity effect was addressed by considering three parameters: mean permeability, the vertical to horizontal permeability ratio, and permeability variation. Sensitivity analysis was carried out using iSIGHT software (design of experiments) to determine the dominant factors affecting CO2 storage capacity and injectivity. Simulation results show that the most favorable option is the perforation of all layers with horizontal wells 250–300 m long set in the upper layers. Mean permeability has the most effect on CO2 storage capacity and injectivity; k v/k h affects CO2 injectivity storage capacity more than permeability variation, V k. More CO2 can be stored in the heterogeneous reservoirs with low mean permeability; however, high injectivity can be achieved in the uniform reservoirs with high mean permeability.  相似文献   

6.
Carbon sequestration in shallow aquifers can be facilitated by water withdrawal. The factors that optimize the injection/withdrawal balance to minimize potential environmental impacts have been studied, including reservoir size, well pattern, injection rate, reservoir heterogeneity, anisotropy ratio, and permeability sequence. The effects of these factors on CO2 storage capacity and efficiency were studied using a compositional simulator Computer Modeling Group-General Equation of State Model, which modeled features including residual gas trapping, CO2 solubility, and mineralization reactions. Two terms, storage efficiency and CO2 relative breakthrough time, were introduced to better describe the problem. The simulation results show that simultaneous water withdrawal during CO2 injection greatly improves CO2 storage capacity and efficiency. A certain degree of heterogeneity or anisotropy benefits CO2 storage. A high injection rate favors storage capacity, but reduces the storage efficiency and CO2 breakthrough time, which in turn limits the total amount of CO2 injected.  相似文献   

7.
A long-term (up to 10 ka) geochemical change in saline aquifer CO2 storage was studied using the TOUGHREACT simulator, on a 2-dimensional, 2-layered model representing the underground geologic and hydrogeologic conditions of the Tokyo Bay area that is one of the areas of the largest CO2 emissions in the world. In the storage system characterized by low permeability of reservoir and cap rock, the dominant storage mechanism is found to be solubility trapping that includes the dissolution and dissociation of injected CO2 in the aqueous phase followed by geochemical reactions to dissolve minerals in the rocks. The CO2–water–rock interaction in the storage system (mainly in the reservoir) changes the properties of water in a mushroom-like CO2 plume, which eventually leads to convective mixing driven by gravitational instability. The geochemically evolved aqueous phase precipitates carbonates in the plume front due to a local rise in pH with mixing of unaffected reservoir water. The carbonate precipitation occurs extensively within the plume after the end of its enlargement, fixing injected CO2 in a long, geologic period.Dawsonite, a Na–Al carbonate, is initially formed throughout the plume from consumption of plagioclase in the reservoir rock, but is found to be a transient phase finally disappearing from most of the CO2-affected part of the system. The mineral is unstable relative to more common types of carbonates in the geochemical evolution of the CO2 storage system initially having formation water of relatively low salinity. The exception is the reservoir-cap rock boundary where CO2 saturation remains very high throughout the simulation period.  相似文献   

8.
The Upper Paleozoic section contains a tight gas sandstone reservoir (of 2.75 × 1012 m3) in the Ordos Basin, central China. The measured porosities (< 10%) and permeabilities (generally < 1 mD) are the result of significant mechanical and chemical compaction and precipitation of carbonate, quartz and authigenic clay cements. Fluid inclusion geochemistry and kinetic modeling (generation of gaseous components and δ13C1) were integrated to constrain the timing of gas charge into the tight reservoir. The modeling results indicate that the natural gases in the present reservoir are similar to gases liberated from quartz inclusions in both composition and stable carbon isotope values and also similar to gas generated from Upper Paleozoic coal. The similar geochemistry suggests that an important phase of quartz cementation must have occurred after gas emplacement in the reservoirs during regional uplift at the end of the Cretaceous. The latest carbonate cement, postdating quartz cementation, consumed most of the late CO2 generated from coal at high maturity (RO > 1.7%) and reduced the reservoir quality dramatically. On the contrary, tight sandstones from non-producing areas have fluid inclusions that were trapped in quartz cements much earlier. These data indicate that natural gas migrated into the Upper Paleozoic reservoir when it still retained high porosity and permeability. The reservoir continued to experience porosity and permeability reduction from continued quartz and carbonate cementation after gas charging due to low gas saturation. Comparison of the relative timing of gas charging with that of sandstone cementation can help to predict areas of risk during tight gas exploration and development.  相似文献   

9.
In order to detect hydraulic and geochemical impact on the groundwater directly above the CO2 storage reservoir at the Ketzin pilot site continuous monitoring using an observation well is carried out. The target depth (446 m below ground level, bgl.) of the well is the Exter formation (Upper Triassic, Rhaetian) which is the closest permeable stratigraphic overlying formation to the CO2 storage reservoir (630–636 m bgl. at well location). The monitoring concept comprises evaluation of hydraulic conditions, temperature, water chemistry, gas geochemistry and δ13C values. This is achieved by a tubing inserted inside the well with installed pressure sensors and a U-tube sampling system so that pumping tests or additional wireline logging can be carried out simultaneously with monitoring. The aquifer was examined using a pump test. The observation well is hydraulically connected to the regional aquifer system and the permeability of about 1.8 D is comparatively high. Between Sept. 2011 and Oct. 2012, a pressure increase of 7.4 kPa is observed during monitoring under environmental conditions. Drilling was carried out with drilling mud on carbonate basis. The concentration of residual drilling mud decreases during the pump test, but all samples show a residual concentration of drilling mud. The formation fluid composition is recalculated with PHREEQC and is comparable to the literature values for the Exter formation. The gas partial pressure is below saturation at standard conditions and the composition is dominated by N2 similar to the underlying storage reservoir prior to CO2 injection. The impact of residual drilling mud on dissolved inorganic carbon and the respective δ13C values decreases during the monitoring period. The pristine isotopic composition cannot be determined due to calcite precipitation. No conclusive results indicate a leakage from the underlying CO2 storage reservoir.  相似文献   

10.
大牛地气田山西组一段储层的孔隙度和渗透率均低、孔隙结构复杂、非均质性强，具有低压、低产的特征。利用测井资料，采用人工神经网络技术对致密砂岩的岩性进行了识别，共识别出中—粗粒岩屑砂岩、岩屑石英砂岩两种岩性，结合三种孔隙度测井方法进行了孔隙度和渗透率的预测，利用岩电实验资料，建立了储层微观孔隙结构与胶结指数、饱和度指数、岩石弹性力学参数之间的统计关系，获得了有效的饱和度评价参数，提高了饱和度的解释精度。并以压汞、相渗等岩芯分析资料进行了束缚水饱和度的解释，并采用多种交绘图技术，有效地识别了致密砂岩气层。该方法的特点是充分放大测井信息对天然气的响应特征，增强了气层和干层的判别差异。实践表明，上述方法对于鄂尔多斯盆地大牛地气田致密砂岩气层测井评价的符合率达到95％以上。  相似文献   

11.
中国鄂尔多斯盆地苏里格气田广覆性含气,但含气量差异较大。为了探讨影响气水相互作用背景下的流体运移特征,选取了陕234-235井区盒8段和山1段的13块样品,基于气水相渗实验进行研究和分析。结果表明：研究区目的层位储层渗流能力较差,几乎不含Ⅰ型气水相渗曲线,具有Ⅱ型气水相渗曲线的储层是勘探开发的首选层段;可动流体孔隙度、孔隙度、可动流体饱和度、渗透率、有效孔隙体积、有效喉道体积、石英体积分数和碳酸盐岩体积分数对可开采气体的储集空间大小,即可动气体孔隙度大小,具有积极的影响,同时,上述前7种因素对气体的渗流能力,即最大有效气相渗透率,也起着积极的作用;而黏土矿物体积分数对可开采气体的储集空间和渗流能力均起着消极的作用。  相似文献   

12.
Carbon dioxide enhanced oil recovery (CO2-EOR) has been widely applied to the process of carbon capture, utilization, and storage (CCUS). Here, we investigate CO2–oil–water–rock interactions under reservoir conditions (100 °C and 24 MPa) in order to understand the fluid–rock interactions following termination of a CO2-EOR project. Our experimental results show that CO2-rich fluid remained the active fluid controlling the dissolution–precipitation processes in an oil-undersaturated sandstone reservoir; e.g., the dissolution of feldspar and calcite, and the precipitation of kaolinite as well as solid phases comprising O, Si, Al, Na, C, and Ti. Mineral dissolution rates were reduced in the case that mineral surfaces were coated by oil. Mineral wettability and composition, and oil saturation were the main controls on the exposed surface area of grains, and mineral wettability in particular led to selective dissolution. In addition, the permeability of the reservoir decreased substantially due to the precipitation of kaolinite and solid-phase particles, and due to the clogging of less soluble mineral particles released by the dissolution of K-feldspar and carbonate cement, whereas porosity increased. The results provide insight into potential formation damage resulting from CO2-EOR projects.  相似文献   

13.
The injection of CO2 into depleted natural gas reservoirs has been proposed as a promising new technology for combining enhanced gas recovery and geological storage of CO2. During the injection, application of suitable techniques for monitoring of the induced changes in the subsurface is required. Observing the movement and the changes in saturation of the fluids contained in the reservoir and the confining strata is among the primary aims here. It is shown that under conditions similar to the Altmark site, Germany, pulsed neutron-gamma logging can be applied with limitations. The pulsed neutron-gamma method can be applied for detection and quantification of changes in brine saturation and water content, whereas changes in the gas composition are below the detection limit. A method to account for the effects of salt precipitation resulting from evaporation of residual brine is presented.  相似文献   

14.
在分析淮南矿区煤层气地质背景的基础上,采用含量梯度法、压力—吸附法计算了研究区可采煤层的剩余煤层气资源量,探讨了影响该区煤层气可采潜力的煤储层压力、渗透能力、吸附/解吸特征、含气饱和度、可采系数等因素。结果表明,淮南矿区-1 500m以浅剩余煤层气资源量为2 419.70×108m3,可采资源量为1 102.20×108m3,可采资源丰度为1.98×108m3/km2,属于中等储量丰度的大型气田;区内煤储层为正常压力储层,煤储层渗透率、含气饱和度偏低,但本区可采煤层层数多,在渗透率总体偏低的背景下,区内存在的高渗区,具备煤层气地面开采的基础地质条件。  相似文献   

15.
Numerical models are essential tools in fully understanding the fate of injected CO2 for commercial-scale sequestration projects and should be included in the life cycle of a project. Common practice involves modeling the behavior of CO2 during and after injection using site-specific reservoir and caprock properties. Little has been done to systematically evaluate and compare the effects of a broad but realistic range of reservoir and caprock properties on potential CO2 leakage through caprocks. This effort requires sampling the physically measurable range of caprock and reservoir properties, and performing numerical simulations of CO2 migration and leakage. In this study, factors affecting CO2 leakage through intact caprocks are identified. Their physical ranges are determined from the literature from various field sites. A quasi-Monte Carlo sampling approach is used such that the full range of caprock and reservoir properties can be evaluated without bias and redundant simulations. For each set of sampled properties, the migration of injected CO2 is simulated for up to 200 years using the water–salt–CO2 operational mode of the STOMP simulator. Preliminary results show that critical factors determining CO2 leakage rate through caprocks are, in decreasing order of significance, the caprock thickness, caprock permeability, reservoir permeability, caprock porosity, and reservoir porosity. This study provides a function for prediction of potential CO2 leakage risk due to permeation of intact caprock and identifies a range of acceptable seal thicknesses and permeability for sequestration projects. The study includes an evaluation of the dependence of CO2 injectivity on reservoir properties.  相似文献   

16.
Carbon dioxide capture and geological storage (CCGS) is an emerging technology that is increasingly being considered for reducing greenhouse gas emissions to the atmosphere. Deep saline aquifers provide a very large capacity for CO2 storage and, unlike hydrocarbon reservoirs and coal beds, are immediately accessible and are found in all sedimentary basins. Proper understanding of the displacement character of CO2-brine systems at in-situ conditions is essential in ascertaining CO2 injectivity, migration and trapping in the pore space as a residual gas or supercritical fluid, and in assessing the suitability and safety of prospective CO2 storage sites. Because of lack of published data, the authors conducted a program of measuring the relative permeability and other displacement characteristics of CO2-brine systems for sandstone, carbonate and shale formations in central Alberta in western Canada. The tested formations are representative of the in-situ characteristics of deep saline aquifers in compacted on-shore North American sedimentary basins. The results show that the capillary pressure, interfacial tension, relative permeability and other displacements characteristics of CO2-brine systems depend on the in-situ conditions of pressure, temperature and water salinity, and on the pore size distribution of the sedimentary rock. This paper presents a synthesis and interpretation of the results.  相似文献   

17.
CO2增强页岩气开采技术(CO2-ESGR)一方面可提高CH4产量,另一方面又可实现CO2地质封存。为了分析页岩储层物性参数对CO2封存机制的影响,文章以鄂尔多斯盆地延长组页岩为研究对象,采用CMG-GEM软件建立双孔双渗均质模型,分析了CO2-ESGR中页岩储层垂直渗透率与水平渗透率之比(Kv/Kh)、含水饱和度和孔隙度对不同CO2封存机制封存量的影响;并设计了27组正交试验采用极差分析法比较了三种因素的影响程度。研究表明,Kv/Kh在0.1～1范围增大会增加不同CO2封存机制的封存量,封存总量最大可增加69.96%,其中吸附封存量最大可增加97.96%,受到影响最大;含水饱和度在0～0.9范围增大引起CO2封存总量先增加后减小,封存总量最大可减少67.12%,其中溶解封存量最大可减少83.35%,范围波动最大;页岩储层孔隙度在0.1～0.99范围增大会导致CO2封存总量减少,封存总量最大...  相似文献   

18.
The sensitivity of coal permeability to the effective stress means that changes in stress as well as pore pressure within a coal seam lead to changes in permeability. In addition coal swells with gas adsorption and shrinks with desorption; these sorption strains impact on the coal stress state and thus the permeability. Therefore the consideration of gas migration in coal requires an appreciation of the coupled geomechanical behaviour. A number of approaches to representing coal permeability incorporate the geomechanical response and have found widespread use in reservoir simulation. However these approaches are based on two simplifying assumptions; uniaxial strain (i.e. zero strain in the horizontal plane) and constant vertical stress. This paper investigates the accuracy of these assumptions for reservoir simulation of enhanced coalbed methane through CO2 sequestration. A coupled simulation approach is used where the coalbed methane simulator SIMED II is coupled with the geomechanical model FLAC3D. This model is applied to three simulation case studies assembled from information presented in the literature. Two of these are for 100% CO2 injection, while the final example is where a flue gas (12.5% CO2 and 87.5% N2) is injected. It was found that the horizontal contrast in sorption strain within the coal seam caused by spatial differences in the total gas content leads to vertical stress variation. Thus the permeability calculated from the coupled simulation and that using an existing coal permeability model, the Shi–Durucan model, are significantly different; for the region in the vicinity of the production well the coupled permeability is greater than the Shi–Durucan model. In the vicinity of the injection well the permeability is less than that calculated using the Shi–Durucan model. This response is a function of the magnitude of the strain contrast within the seam and dissipates as these contrasts diminish.  相似文献   

19.
The present paper provides a case study of the assessment of the potential for CO2 storage in the deep saline aquifers of the Bécancour region in southern Québec. This assessment was based on a hydrogeological and petrophysical characterization using existing and newly acquired core and well log data from hydrocarbon exploration wells. Analyses of data obtained from different sources provide a good understanding of the reservoir hydrogeology and petrophysics. Profiles of formation pressure, temperature, density, viscosity, porosity, permeability, and net pay were established for Lower Paleozoic sedimentary aquifers. Lateral hydraulic continuity is dominant at the regional scale, whereas vertical discontinuities are apparent for most physical and chemical properties. The Covey Hill sandstone appears as the most suitable saline aquifer for CO2 injection/storage. This unit is found at a depth of more than 1 km and has the following properties: fluid pressures exceed 14 MPa, temperature is above 35 °C, salinity is about 108,500 mg/l, matrix permeability is in the order of 3 × 10?16 m2 (0.3 mDarcy) with expected higher values of formation-scale permeability due to the presence of natural fractures, mean porosity is 6 %, net pay reaches 282 m, available pore volume per surface area is 17 m3/m2, rock compressibility is 2 × 10?9 Pa?1 and capillary displacement pressure of brine by CO2 is about 0.4 MPa. While the containment for CO2 storage in the Bécancour saline aquifers can be ensured by appropriate reservoir characteristics, the injectivity of CO2 and the storage capacity could be limiting factors due to the overall low permeability of aquifers. This characterization offers a solid basis for the subsequent development of a numerical hydrogeological model, which will be used for CO2 injection capacity estimation, CO2 injection scenarios and risk assessment.  相似文献   

20.
To accurately measure and evaluate reserves is critical for ensuring successful production of unconventional oil and gas. This work proposes a volumetric model to evaluate the tight sandstone gas reserves of the Permian Sulige gas field in the Ordos Basin. The reserves can be determined by four major parameters of reservoir cutoffs, net pay, gas-bearing area and compression factor Z, which are controlled by reservoir characteristics and sedimentation. Well logging, seismic analysis, core analysis and gas testing, as well as thin section identification and SEM analysis were used to analyze the pore evolution and pore-throat structure. The porosity and permeability cutoffs are determined by distribution function curve,empirical statistics and intersection plot. Net pay and gas-bearing area are determined based on the cutoffs, gas testing and sand body distribution, and the compression factor Z is obtained by gas component. The results demonstrate that the reservoir in the Sulige gas field is characterized by ultralow porosity and permeability, and the cutoffs of porosity and permeability are 5% and 0.15×10~(–3) μm~2, respectively. The net pay and gas-bearing area are mainly affected by the sedimentary facies, sand body types and distribution. The gas component is dominated by methane which accounts for more than 90%, and the compression factor Z of H_8(P_2h_8) and S_1(P_1s_1) are 0.98 and 0.985, respectively. The distributary channels stacked and overlapped, forming a wide and thick sand body with good developed intergranular pores and intercrystalline pores. The upper part of channel sand with good porosity and permeability can be sweet spot for gas exploration. The complete set of calculation systems proposed for tight gas reserve calculation has proved to be effective based on application and feedback. This model provides a new concept and consideration for reserve prediction and calculation in other areas.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号