共查询到20条相似文献，搜索用时 15 毫秒
1.
The use of ballastless slab track is significantly increasing in HST line technology. This development is due to some structural and operational advantages over ballasted track. In addition, floating slab tracks can be used to control ground-borne vibrations generated by surface and underground rail transportation systems. In this paper, a general and fully three dimensional multi-body-finite element-boundary element model is used to study vibrations due to train passage on ballast and non-ballast tracks. The vehicle is modelled as a multi-body system, the track, in both cases, using finite elements and the soil is represented using boundary elements. The three components of the load are considered; the quasi-static excitation (force generated by moving axle loads), the parametric excitation due to discrete supports of the rails and the excitation due to wheel and rail roughness and track unevenness. Track receptances are computed for both track systems and vibrations induced by high-speed train passage at the track and the free-field are evaluated for different train speeds. Soil behaviour changes significantly with the track system. Finally, a floating slab track is studied to show how this type of solution leads to a significant vibration reduction for surface tracks. 相似文献
2.
This paper explores dynamic soil–bridge interaction in high speed railway lines. The analysis was conducted using a general and fully three-dimensional multi-body finite element–boundary element model formulated in the time domain to predict vibrations caused by trains passing over the bridge. The vehicle was modelled as a multi-body system, the track and the bridge were modelled using finite elements and the soil was considered as a half-space by the boundary element method. The dynamic response of bridges to vehicle passage is usually studied using moving force and moving mass models. However, the multi-body system allows to consider the quasi-static and dynamic excitation mechanisms. Soil–structure interaction was taken into account by coupling finite elements and boundary elements. The paper presents the results obtained for a simply supported short span bridge in a resonant regime under different soil stiffness conditions. 相似文献
3.
Reduction of ground vibration by means of barriers or soil improvement along a railway track 总被引：3，自引：0，他引：3
Trains running in built-up areas are a source to ground-borne noise. A careful design of the track may be one way of minimizing the vibrations in the surroundings. For example, open or infilled trenches may be constructed along the track, or the soil underneath the track may be improved. In this work, the influence of the track design and properties on the level of ground vibration due to a vehicle moving with subsonic speed is examined. A coupled finite element-boundary element model of the track and subsoil is employed, adopting a formulation in the moving frame of reference following the vehicle. The computations are carried out in the frequency domain for various combinations of the vehicle speed and the excitation frequency. The analyses indicate that open trenches are more efficient than infilled trenches or soil stiffening–even at low frequencies. However, the direction of the load is of paramount importance. For example, the response outside a shallow open trench may change dramatically when horizontal load is applied instead of vertical load. 相似文献
4.
This paper outlines a vibration prediction tool, ScopeRail, capable of predicting in-door noise and vibration, within structures in close proximity to high speed railway lines. The tool is designed to rapidly predict vibration levels over large track distances, while using historical soil information to increase accuracy. Model results are compared to an alternative, commonly used, scoping model and it is found that ScopeRail offers higher accuracy predictions. This increased accuracy can potentially reduce the cost of vibration environmental impact assessments for new high speed rail lines.To develop the tool, a three-dimensional finite element model is first outlined capable of simulating vibration generation and propagation from high speed rail lines. A vast array of model permutations are computed to assess the effect of each input parameter on absolute ground vibration levels. These relations are analysed using a machine learning approach, resulting in a model that can instantly predict ground vibration levels in the presence of different train speeds and soil profiles. Then a collection of empirical factors are coupled with the model to allow for the prediction of structural vibration and in-door noise in buildings located near high speed lines. Additional factors are also used to enable the prediction of vibrations in the presence of abatement measures (e.g. ballast mats and floating slab tracks) and additional excitation mechanisms (e.g. wheelflats and switches/crossings). 相似文献
5.
P. Galvín S. François M. Schevenels E. Bongini G. Degrande G. Lombaert 《Soil Dynamics and Earthquake Engineering》2010
Ground vibrations induced by railway traffic at grade and in tunnels are often studied by means of two-and-half dimensional (2.5D) models that are based on a Fourier transform of the coordinate in the longitudinal direction of the track. In this paper, the need for 2.5D coupled finite element-boundary element models is demonstrated in two cases where the prediction of railway induced vibrations is considered. A recently proposed novel 2.5D methodology is used where the finite element method is combined with a boundary element method, based on a regularized boundary integral equation. In the formulation of the boundary integral equation, Green's functions of a layered elastic halfspace are used, so that no discretization of the free surface or the layer interfaces is required. In the first case, two alternative models for a ballasted track on an embankment are compared. In the first model, the ballast and the embankment are modelled as a continuum using 2.5D solid elements, whereas a simplified beam representation is adopted in the second model. The free field vibrations predicted by both models are compared to those measured during a passage of the TGVA at a site in Reugny (France). A very large difference is found for the free field response of both models that is due to the fact that the deformation of the cross section of the embankment is disregarded in the simplified representation. In the second case, the track and free field response due to a harmonic load in a tunnel embedded in a layered halfspace are considered. A simplified methodology based on the use of the full space Green's function in the tunnel–soil interaction problem is investigated. It is shown that the rigorous finite element-boundary element method is required when the distance between the tunnel and the free surface and the layer interfaces of the halfspace is small compared to the wavelength in the soil. 相似文献
6.
Seismic performance and dynamic response of bridge–embankments during strong or moderate ground excitations are investigated through finite element (FE) modelling and detailed dynamic analysis. Previous research studies have established that bridge–embankments exhibit increasingly flexible performance under high‐shear deformation levels and that soil displacements at bridge abutment supports may be significant particularly in the transverse direction. The 2D equation of motion is solved for the embankment, in order to evaluate the dynamic characteristics and to describe explicitly the seismic performance and dynamic response under transverse excitations accounting for soil nonlinearities, soil–structure interaction and imposed boundary conditions (BCs). Using the proposed model, equivalent elastic analysis was performed so as to evaluate the dynamic response of approach embankments while accounting for soil–structure interaction. The analytical procedures were applied in the case of a well‐documented bridge with monolithic supports (Painter Street Overcrossing, PSO) which had been instrumented and embankment participation was identified from its response records after the 1971 San Fernando earthquake. The dynamic characteristics and dynamic response of the PSO embankments were evaluated for alternative BCs accounting for soil–structure interaction. Explicit expressions for the evaluation of the critical embankment length Lc are provided in order to quantify soil contribution to the overall bridge system under strong intensity ground excitations. The dynamic response of the entire bridge system (deck–abutments–embankments) was also evaluated through simplified models that considered soil–structure interaction. Results obtained from this analysis are correlated with those of detailed 3D FE models and field data with good agreement. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
7.
This study proposes a Green’s function,an essential representation of water-saturated ground under moving excitation,to simulate ground borne vibration from trains.First,general solutions to the governing equations of poroelastic medium are derived by means of integral transform.Secondly,the transmission and reflection matrix approach is used to formulate the relationship between displacement and stress of the stratified ground,which results in the matrix of the Green’s function.Then the Green’s function is combined into a train-track-ground model,and is verified by typical examples and a field test.Additional simulations show that the computed ground vibration attenuates faster in the immediate vicinity of the track than in the surrounding area.The wavelength of wheel-rail unevenness has a notable effect on computed displacement and pore pressure.The variation of vibration intensity with the depth of ground is significantly influenced by the layering of the strata soil.When the train speed is equal to the velocity of the Rayleigh wave,the Mach cone appears in the simulated wave field.The proposed Green’s function is an appropriate representation for a layered ground with shallow ground water table,and will be helpful to understand the dynamic responses of the ground to complicated moving excitation. 相似文献
8.
This paper presents the concept of using an additional generator to prevent ground vibrations. A linear, transversally isotropic three dimensional half-space with the hysteretic damping model, acted upon by a harmonic vertical excitation is assumed. Equations of motion for the transversally isotropic ground model with the absorbing boundary conditions are presented and numerically integrated using FlexPDE software, based on the finite element method. The efficiency of the solution is analysed in terms of reducing the vertical and horizontal components of ground surface vibrations. Results in the form of a dimensionless amplitude reduction factor are presented for four different locations of a generator. The influence of the soil parameters and layers locations on the additional generator's efficiency is investigated. The vibration reduction efficiency in a four-story building is also presented. 相似文献
9.
Recent advances in railway-induced ground vibrations showed that the track/soil interaction plays an important role in the low frequency range. This paper contributes to the numerical analysis of train/track/foundation dynamics by presenting the accuracy of a coupled lumped mass (CLM) model devoted to the railway foundations and to the track/soil coupling. Following a summary of the background and the advantages of the CLM model, the coupling strategy is quantified through two application cases. Firstly, the dynamic track deflection is calculated for different railway lines considering various degrees of complexities of foundations. Then, the foundation responses are compared depending on whether detailed coupling is introduced or not. The benefit of the proposed model is emphasized by presenting free-field ground vibration responses generated by a tram and a high-speed train, obtained by a revisited two-step prediction model developed by the authors. 相似文献
10.
Soft ground improvement using piles has increasingly been used as a rapid construction technique for railway and highway embankments over soft soil areas. While most studies conducted so far have addressed only issues of stability and settlement of pile-supported embankments under static loading, very limited attention has been paid to understanding their behaviors under transient loading of moving vehicles. In this study, vibration behaviors of this embankment system under high-speed train passage are investigated through three-dimensional finite element simulation. They include (1) characteristics of the surface wave field at high train speeds, (2) the dependence of vibration amplitude on the train speed and the phenomenon of critical speed, and (3) response at some typical locations in the system when the train moves at the critical speed. The study shows that there are breaks in the simulated wave fronts as transiting between different materials due to the difference in the Rayleigh wave speed among the materials relative to the train speed, and that the increase in train speed is accompanied by the increase in phase shift between the train load and the displacement pattern beneath the load. It is shown that the critical speed of the system is governed by the embankment, instead of the soft soil as commonly observed in previous studies in which the ground is not improved. Namely the vibration amplitude is maximally amplified when the train speed approaches the characteristic Rayleigh wave speed of the embankment material. In addition, the results also suggest that the sloping surfaces on the ballast and embankment along with the piles form a ‘trapping’ effect by which most of the train-induced waves, especially higher-frequency waves, incident to the sloping surfaces are trapped and dissipated within the pile-supported embankment system, and thus significantly reducing vibration amplitudes outside the embankment. 相似文献
11.
R. Paolucci A. Maffeis L. Scandella M. Stupazzini M. Vanini 《Soil Dynamics and Earthquake Engineering》2003,23(6):425-433
The ground vibrations induced by a passenger train at the test site of Ledsgaard, Sweden, have been analysed and numerically simulated through a spectral element discretization of the soil. To calculate the spatial distribution of loading due to train passage, the train is decoupled from the track, and a suitable series of static forces is applied. The track and the embankment are modeled as a beam on elastic foundation, using analytical solutions for loads moving at constant velocity. The results of both 2D and 3D modelling assumptions are thoroughly discussed, in terms of prediction of track motion and of attenuation of peak ground velocity with distance. 相似文献
12.
Because of its direct influence on the amount of unfrozen water and on the strength of intergranular ice in a frozen soil, temperature has a significant effect on all aspects of the mechanical behavior of the active layer in which temperature fluctuates above and below 0 °C. Hence seismic responses of engineering structures such as embankment on a sloping ground in permafrost regions exhibit obvious differences with seasonal alternation. To explore the distinctive seismic characteristics of a railway embankment on the sloping ground in permafrost regions, a coupled water-heat-dynamics model is built based on theories of heat transfer, soil moisture dynamics, frozen soil mechanics, soil dynamics, and so on. A well-monitored railway embankment on a sloping ground in Qinghai–Tibet Plateau is taken as an example to simulate seismic responses in four typical seasons in the 25th service year. The numerical results show that seismic acceleration, velocity and displacement responses are significantly different in four typical seasons, and the responses on October 15 are much higher among the four seasons. When the earthquake is over, there are still permanent differential deformations in the embankment and even severe damages on the left slope on October 15. Therefore, this position should be monitored closely and repaired timely to ensure safe operation. In addition, the numerical model and results may be a reference for maintenance, design and study on other embankments in permafrost regions. 相似文献
13.
Damage of embankments during earthquakes is widely attributed to the liquefaction of foundation soil. Previous studies have investigated the dynamic response of embankments by mainly considering uniform sand foundation and a single earthquake event. However, the foundation of an embankment consists of many sublayers of soil from liquefiable sand to relatively impermeable layer, and during earthquakes a mainshock may trigger numerous aftershocks within a short time which may have the potential to cause additional damage to soil structures. Accordingly, the investigation of liquefaction-induced deformation of earthen embankments on various liquefiable foundation conditions under mainshock–aftershock sequential ground motions is carried out by a series of dynamic centrifuge tests in this study. The liquefiable foundation includes uniform sand profile, continuous layered soil profile, and non-homogeneous soil profiles. Effects of various foundation conditions on embankment deformations are compared and analyzed. From the test results, it is found that the embankment resting on non-homogeneous soil deposits suffer more damage compared to the uniform sand foundation of same relative density. The test results also suggest that the sequential ground motions have a significant effect on the accumulated deformation of embankment. 相似文献
14.
Piled embankments, which offer many advantages, are increasingly popular in construction of high-speed railways in China. Although the performance of piled embankment under static loading is well-known, the behavior under the dynamic train load of a high-speed railway is not yet understood. In light of this, a heavily instrumented piled embankment model was set up, and a model test was carried out, in which a servo-hydraulic actuator outputting M-shaped waves was adopted to simulate the process of a running train. Earth pressure, settlement, strain in the geogrid and pile and excess pore water pressure were measured. The results show that the soil arching height under the dynamic train load of a high-speed railway is shorter than under static loading. The growth trend for accumulated settlement slowed down after long-term vibration although there was still a tendency for it to increase. Accumulated geogrid strain has an increasing tendency after long-term vibration. The closer the embankment edge, the greater the geogrid strain over the subsoil. Strains in the pile were smaller under dynamic train loads, and their distribution was different from that under static loading. At the same elevation, excess pore water pressure under the track slab was greater than that under the embankment shoulder. 相似文献
15.
This paper has two main purposes. One is to present and analyse soil and structural vibration data obtained experimentally during certification testing of the high-speed train line between Córdoba and Málaga (Spain) that was opened on December 2007. The second is to show the capabilities of a three-dimensional boundary element method (BEM)/finite element method (FEM) numerical approach for the analysis of train induced vibrations. The model can represent local soil conditions, discontinuities such as underpasses, as well as structures placed next to the rail track. Vibrations in those structures can be computed taking into account, in a rigorous way, dynamic soil–structure interaction and local soil properties. Experimental and numerical results at several points near the track are compared. Results for an overhead contact support structure are also evaluated. The comparison of numerically predicted and recorded results shows that the model is reliable for predicting the amplitude of vibrations produced in the soil and nearby structures by high-speed trains. 相似文献
16.
The effectiveness of heavy masses next to the track as a measure for the reduction of railway induced ground vibration is investigated by means of numerical simulations. It is assumed that the heavy masses are placed in a continuous row along the track forming a wall. Such a continuous wall could be built as a gabion wall and also used as a noise barrier. Since the performance of mitigation measures on the transmission path strongly depends on local ground conditions, a parametric study is performed for a range of possible designs in a set of different ground types. A two-and-a-half dimensional coupled finite element–boundary element methodology is used, assuming that the geometry of the problem is uniform in the direction along the track. It is found that the heavy masses start to be effective above the mass–spring resonance frequency which is determined by the dynamic stiffness of the soil and the mass of the wall. At frequencies above this resonance frequency, masses at the soil׳s surface hinder the propagation of surface waves. It is therefore beneficial to make the footprint of the masses as large and stiff as possible. For homogeneous soil conditions, the effectiveness is nearly independent of the distance behind the wall. In the case of a layered soil with a soft top layer, the vibration reduction strongly decreases with increasing distance from the wall. 相似文献
17.
Robert Hildebrand 《Soil Dynamics and Earthquake Engineering》2004,24(5):411-424
Although railway-generated ground vibrations usually have greater energy levels at lower frequencies, vibrations in the audible range above 20 Hz can nevertheless be relevant for secondary noise problems in buildings. One countermeasure is soil stabilization under the track embankment. While effective at low frequencies, a potential side effect is amplification in some audible bands. Presented here are both experimental and theoretical assessments of the countermeasure in the audible bands. The main innovation is the treatment of an infinite periodic track–ground system, using a transfer matrix approach with a repeating element including the rail, pad, sleeper, and an underlying half-space (ballast and soil). Excitation in this band is attributed to rail and wheel roughness. The model makes successful predictions when the half-space properties are allowed to be frequency-dependent such that the dispersion of the surface wave matches that in the actual layered earth (including ballast and underlying soil layers). The field measurements are also unique in that both before and after evaluation of the countermeasure was possible. 相似文献
18.
Sayed Mahmoud Ayman Abd-Elhamed Robert Jankowski 《Bulletin of Earthquake Engineering》2013,11(4):1021-1048
The present paper investigates the coupled effect of the supporting soil flexibility and pounding between neighbouring, insufficiently separated equal height buildings under earthquake excitation. Two adjacent three-storey structures, modelled as inelastic lumped mass systems with different structural characteristics, have been considered in the study. The models have been excited using a suit of ground motions with different peak ground accelerations and recorded at different soil types. A nonlinear viscoelastic pounding force model has been employed in order to effectively capture impact forces during collisions. Spring-dashpot elements have been incorporated to simulate the horizontal and rotational movements of the supporting soil. The results of the numerical simulations, in the form of the structural nonlinear responses as well as the time-histories of energy dissipated during pounding-involved vibrations, are presented in the paper. In addition, the variation in storeys peak responses and peak dissipated energies for different gap sizes are also shown and comparisons are made with the results obtained for colliding buildings with fixed-base supports. Observations regarding the incorporation of the soil-structure interaction and its effect on the responses obtained are discussed. The results of the study indicate that the soil-structure interaction significantly influences the pounding-involved responses of equal height buildings during earthquakes, especially the response of the lighter and more flexible structure. It has been found that the soil flexibility decreases storey peak displacements, peak impact forces and peak energies dissipated during vibrations, whereas it usually leads to the increases in the peak accelerations at each storey level. 相似文献
19.
In recent years, the high-speed train (HST) network has developed considerably, unfortunately increasing vibration nuisances in its neighbourhood. This paper aims to present some vibration measurements collected on a Belgian site located between Brussels and Paris/London and travelled by the Thalys and Eurostar high-speed trains, and to compare them with the results obtained by a recently developed model, involving the compound vehicle/track/soil system. Assuming that the soil can be reasonably decoupled from the track, the approach first considers the train/track subsystem. The latter is studied by combining a multibody model of the vehicle with a finite element model of the track, both so far limited to the vertical motion. The ground forces given by this first simulation are then applied on a finite/infinite element model of the soil subsystem, where the infinite elements are placed on the border of the mesh in order to properly represent an unbounded domain. Both simulations are performed in the time domain, offering the opportunity to include non-linearities. The good correspondence between numerical and experimental results shows that the model is reliable for predicting the vibration produced by the high-speed vehicles. Finally, the paper presents some cases showing the importance of including the complete vehicle and the soil layering to the model. 相似文献
20.
A field measurement of ground vibration was performed on the Beijing−Shanghai high-speed railway in China. In this paper, the experimental results of vertical ground vibration accelerations induced by very high speed trains running over a non-ballasted track on embankment with speeds from 300 to 410 km/h are reported and analyzed in detail for the first time. Characteristics of ground vibration accelerations in both time and frequency domains are analyzed based on the test data. It is shown that the periodic exciting action of high-speed train bogies can be identified in time histories of vertical accelerations of the ground within the range of 50 m from the track centerline. The first dominant sensitive frequency of the ground vibration acceleration results from the wheelbase of the bogie, and the center distance of two neighboring cars plays an important role in the significant frequencies of the ground vibration acceleration. Variations of time–response peak value and frequency-weighted vertical acceleration level of ground vibration in relation with train speed as well as the distance from the track centerline are also investigated. Results show that the time-domain peak value of ground vibration acceleration exhibits an approximately linear upward tendency with the increase of train speed. With the increasing distance from the track centerline, the frequency-weighted vertical acceleration level of the ground vibration attenuates more slowly than the time-domain peak value of the ground vibration acceleration does. Severe impact of high-speed railway ground vibration on human body comfort on the ground occurs at the speed of 380–400 km/h. The results given in the paper are also valuable for validating the numerical prediction of train induced ground vibrations. 相似文献