共查询到20条相似文献，搜索用时 31 毫秒
1.
本文首先基于渤海海域的地震环境及地震危险性特征,根据46个海洋平台的设计地震动参数,分析了不同设防水准的设计地震动参数之间的关系;然后,采用与其他工程类比的方法,确定了海洋平台抗震设防的两级目标;通过与国内其他规范的类比,确定了海洋平台强度设计地震的概率水准取重现期200年,变形设计地震的概率水准取重现期1000—2500年,并深入分析论证了其合理性;最后,根据渤海地区的地震危险性分区和地震动参数区划给出了相应的设防参数。本文是对渤海地区多年来海洋平台抗震设防经验的总结,是对我国海洋平台抗震设防标准的探索性研究。 相似文献
2.
渤海地区地震危险性特征及对工程抗震设防的启示 总被引：2，自引：0，他引：2
本文分析了渤海海域地震构造环境及地震活动特征,总结了近年来对该地区潜在震源区划分的一些新认识,分析了地震危险性区划结果.在此基础上,引入地震危险性特征参数K对研究区进行地震危险性分区,通过不同场点的地震危险性曲线证明了地震环境造成的危险性差异,并以研究区内3个概率水准的地震动峰值加速度的比值统计证明了引入地震危险性分区的必要性.研究表明:(1)不同概率水准的地震动参数之间不存在固定的比例关系,受地震环境影响,地震危险性分区和地震动参数区划图结合使用可以更准确地反应地震危险性特征;(2)对于一般工程,根据地震动参数区划图所给的50年超越概率10%的地震动参数折算所得到的小震的地震作用不具有统一的概率水准,抗震设防目标的实现没有科学保证;海洋平台抗震设计中利用强度水平地震推算得到韧性水平地震作用也不具有统一的概率水准;(3)将地震危险性分区和地震动参数区划结合使用或编制统一抗倒塌水准的区划图是一般工程抗震设防的科学做法,对于海洋平台的抗震设防,宜明确韧性水平地震作用的概率水准. 相似文献
3.
不同抗震标准下的海洋石油平台设计地震动参数研究 总被引：3，自引：0，他引：3
在海洋石油平台抗震标准方面,中国与美国规范之间存在一定的差异。本文首先介绍了两国抗震规范中的相关内容。以渤海某油田为例,根据渤海及邻区的地震构造、地震活动环境及地震动衰减关系,利用概率方法进行地震危险性分析;采用一维等效线性化方法,根据场地土动力性能试验资料,确定不同抗震标准下的设计地震动参数。最后分析不同抗震标准下的地震动参数关系,以及对工程设计的影响。结合我国渤海与美国南加利福尼亚地区的地震活动性对比分析,对我国海洋石油平台的设防地震水准提出建议。 相似文献
4.
结构抗震设计中的强度折减系数研究 总被引：27，自引：12，他引：27
借助于单自由度弹塑性动力时程分析程序，对延性结构的强度折减系数进行了研究，在统计平均和回归分析的基础上，建立了平均强度折系数的函数形式，本文所建立的平强度折减系数函数，从理论上明确了结构具有延性对弹性地震力的折减关系，研究成果可供结构抗震设计规范采纳应用。 相似文献
5.
强度折减系数既是基于强度的抗震设计中确定设计地震力的关键因素，又是基于性态的抗震设计理论中确定非弹性反应谱的主要依据. 本文结合我国抗震设计反应谱的形式和特点，应用823条国内外水平向地震动记录（充分利用了我国取得的强震记录），给出了一种考虑设计地震分组和场地类别的强度折减系数模型，研究了结构周期、延性、场地类别、设计地震分组、震级、震中距等因素对强度折减系数的影响. 结果表明:场地条件对强度折减系数的影响是不可忽略的，特别是对延性较大的短周期结构更应注意场地条件的影响；设计地震分组是影响强度折减系数的一个重要因素，在应用我国规范设计反应谱构造非弹性反应谱所用的强度折减系数必须考虑设计分组的影响；震级对强度折减系数的影响较小；如不考虑近场大脉冲地震动记录的影响，震中距对强度折减系数的影响是可以忽略的. 相似文献
6.
Study on strength reduction factors considering the effect of classification of design earthquake 总被引：1，自引：0，他引：1
Introduction The strength reduction factor is defined as the lateral yielding strength required to avoid yielding in the system when subjected to a given ground motion, to the lateral yielding strength required to maintain the displacement ductility ratio demand equal to a pre-determined target duc-tility ratio under the same ground motion. The strength reduction factors are not only the key fac-tors in determining seismic action for force-based seismic design, but also one of the key parame-t… 相似文献
7.
Based on a reliability level 2 method, a procedure is proposed to design reinforced concrete structures for elevated tanks subjected to seismic action, with a specified probability of failure in a 50-year design life. To evaluate the probability of failure the ultimate limit state is obtained when the top column displacement demanded by the earthquake, a random variable, reaches the allowable displacement, which is here treated as deterministic. The seismic action is characterized probabilistically by the power spectral density function of the ground acceleration, which is obtained from a design spectrum. The strength and ductility of an annular column section of confined reinforced concrete for cyclic loads are evaluated with design aids. Design charts are made for a given tank capacity and specified seismic zone that allow one to choose different combinations of strength, stiffness and ductility for the same tolerable probability of failure. A step by step method is suggested for the design of the annular column section, choosing finally the most convenient design. The advantage of this methodology is shown through a numerical example. 相似文献
8.
管道抗震设计规范有关地震作用的综述 总被引：2，自引：0，他引：2
本文通过介绍中国、日本、美国、英国、挪威的相关管道抗震规范,阐述了目前管道应变设计和性能设计的理念、方法以及对地震作用输入的要求。通过比较各国管道抗震设计规范,保证震后管道维持其服务功能的抗震设计理念已经得到了全世界范围的认可。现在的管道设计正向性能设计的方向发展,并提出了两级抗震设防的方法。其中,第二级以管道不发生泄漏为抗震设防目标,对管道的地震安全性评价工作提出了更高的要求,管道设计需要的地震动和地面永久变形参数也越来越多。在目前管道工程的地震安全性评价工作中,存在概率方法和确定性方法这两种方法并举的局面。针对管道的抗液化和滑坡设计,地面永久位移可以利用分解的地震安全性评价概率方法得到。针对管道的抗断设计,断层未来位错量的估计方法现在仍以确定性方法为主,概率方法因为断层位错量沿着破裂带的分布较为复杂仍有待进一步研究。 相似文献
9.
Wang Yayong 《地震工程与工程振动(英文版)》2008,7(3):255-262
Many different types of buildings were severely damaged or collapsed during the May 12, 2008 Great Wenchuan Earthquake. Based on survey data collected in regions that were subjected to moderate to severe earthquake intensities, a comparison between the observed building damage, and the three earthquake performance objectives and seismic conceptual design principles specified by the national ＂Code for Seismic Design of Buildings GB50011-2001,＂ was carried out. Actual damage and predicted damage for a given earthquake level for different types of structures is compared. Discussions on seismic conceptual design principles, with respect to multiple defense lines, strong column-weak beam, link beam of shear walls, ductility detailing of masonry structures, exits and staircases, and nonstructural elements, etc. are carried out. Suggestions for improving the seismic design of structures are also proposed. It is concluded that the seismic performance objectives for three earthquake levels, i.e., ＂no failure under minor earthquake level, ＂＂repairable damage under moderate earthquake level＂ and ＂no collapse under major earthquake level＂ can be achieved if seismic design principles are carried out by strictly following the code requirements and ensuring construction quality. 相似文献
10.
工程场地地震安全性评价工作及相关技术问题 总被引：11，自引：6，他引：5
本文简单回顾了工程场地地震安全性评价工作的变迁与发展过程,探讨了几个关键的技术问题,分析了相关技术方法的发展与更新趋势。文中重点讨论了不同的地震影响量之间概率水平的一致性问题,同时对在设防水准的选取、地震危险性分析中的不确定性考虑、地震动衰减笑系的获取、地震动时程合成中的参数匹配、场地地震反应分析中的非线性处理、设计地震动确定等方面遇到的一些技术问题进行了分析,并且给出了对这些问题处理的一些看法和建议。 相似文献
11.
12.
以汶川地震为研究背景,针对震后典型钢筋混凝土框架结构进行地震易损性研究。基于Cornell理论框架结合汶川地质资料,拟合出考虑场地特点的地震危险性模型,同时定义损伤水平状态及限值指标,以概率解析易损性研究方法为基础,运用考虑地震动参数的解析易损性评估方法绘制汶川地区钢筋混凝土框架建筑的地震易损性曲线。研究结果表明:考虑地震动参数的概率解析易损性研究方法是一种有效的地震易损性评估方法;以PGA作为地震强度输入指标的结构反应,随自振周期的增大体系最大响应的相关性降低,结构各个损伤状态的失效概率均随之增大。 相似文献
13.
Comparison of seismic actions and structural design requirements in Chinese code GB 50011 and international standard ISO 3010 总被引：1，自引：0，他引：1
王亚勇 《地震工程与工程振动(英文版)》2004,3(1):1-9
This paper presents a comparison between the Chinese Code GB50011-2001 and the International Standard ISO3010: 2001(E), emphasizing the similarities and differences related to design requirements, seismic actions and analytical approaches. Similarities include: earthquake return period, conceptual design, site classification, structural strength and ductility requirements, deformation limits, response spectra, seismic analysis procedures, isolation and energy dissipation, and nonstructural elements. Differences exist in the following areas: seismic levels, earthquake loading, mode damping factors and structural control. 相似文献
14.
This paper presents a new methodology based on structural performance to determine uniform fragility design spectra, i.e., spectra with the same probability of exceedance of a performance level for a given seismic intensity. The design spectra calculated with this methodology provide directly the lateral strength, in terms of yield‐ pseudo‐accelerations, associated with the rate of exceedance of a specific ductility characterizing the performance level for which the structures will be designed. This procedure involves the assessment of the seismic hazard using a large enough number of seismic records of several magnitudes; these records are simulated with an improved empirical Green function method. The statistics of the performance of a single degree of freedom system are obtained using Monte Carlo simulation considering the seismic demand, the fundamental period, and the strength of the structure as uncertain variables. With these results, the conditional probability that a structure exceeds a specific performance level is obtained. The authors consider that the proposed procedure is a significant improvement to others considered in the literature and a useful research tool for the further development of uniform fragility spectra that can be used for the performance‐based seismic design and retrofit of structures. 相似文献
15.
This paper assesses the influence of cyclic and in‐cycle degradation on seismic drift demands in moment‐resisting steel frames (MRF) designed to Eurocode 8. The structural characteristics, ground motion frequency content, and level of inelasticity are the primary parameters considered. A set of single‐degree‐of‐freedom (SDOF) systems, subjected to varying levels of inelastic demands, is initially investigated followed by an extensive study on multi‐storey frames. The latter comprises a large number of incremental dynamic analyses (IDA) on 12 frames modelled with or without consideration of degradation effects. A suite of 56 far‐field ground motion records, appropriately scaled to simulate 4 levels of inelastic demand, is employed for the IDA. Characteristic results from a detailed parametric investigation show that maximum response in terms of global and inter‐storey drifts is notably affected by degradation phenomena, in addition to the earthquake frequency content and the scaled inelastic demands. Consistently, both SDOF and frame systems with fundamental periods shorter than the mean period of ground motion can experience higher lateral strength demands and seismic drifts than those of non‐degrading counterparts in the same period range. Also, degrading multi‐storey frames can exhibit distinctly different plastic mechanisms with concentration of drifts at lower levels. Importantly, degrading systems might reach a “near‐collapse” limit state at ductility demand levels comparable to or lower than the assumed design behaviour factor, a result with direct consequences on optimised design situations where over‐strength would be minimal. Finally, the implications of the findings with respect to design‐level limit states are discussed. 相似文献
16.
工程结构等延性地震抗力谱研究 总被引：28，自引：7，他引：21
研究结构的非弹性反应谱对改进现有的结构抗震设计、发展基于性态的抗震设计以及了解复杂地面运动特性与结构动力特性之间的关系具有重要的意义。利用大量的单自由度在强震记录作用下的弹塑性动力时程分析,对等延性地震抗力谱这一重要的非弹性反应谱进行了较为详尽的研究,给出了四类场地条件(基岩、硬土、一般土和软土)下的平均等延性地震抗力谱,总结了对工程结构的抗震设计和研究具有实际意义的规律和特征,并分析了场地条件、结构的延性系数以及周期等对等延性地震抗力谱的影响,提出了新的拟合公式,其成果可供抗震研究和设计直接应用。 相似文献
17.
Historical earthquakes and a tsunami in Bohai Sea 总被引：1，自引：0，他引：1
王健 《地震学报(英文版)》2007,20(5):584-592
Quantitative analysis on seismicity showed that there are several seismic dense zones in Bohai Sea. These seismic dense zones of modern small earthquakes behave prominent NE orientation, although a seismic dense zone with NW direction exists actually. Taking 39°N as a boundary, seismicity in the south is different from that in north of Bohai Sea. Almost all strong earthquakes and seismic dense zones are concentrated in the southern part. Based on archives and seismic dense characteristics, we amended the epicenter of strong earthquakes in 1548 and discussed about magnitude of the earthquake in 1888. Possibility of the event in 173 as a tsunami was discussed. The event in 1597 was doubted as a strong earthquake in Bohai Sea. 相似文献
18.
2020年6月交通运输部发布了新版《公路桥梁抗震设计规范》（JTG/T 2231-01-2020）（简称"《公规》"）。本文比较了现行《铁路工程抗震设计规范》（GB 50111-2006）（2009年版）（以下简称"《铁规》"）与《公规》的抗震设计相关内容,并分别采用两本规范对25m墩高（D类）、35m墩高（C类）和40m墩高（B类）简支梁进行抗震设计,比较二者地震力和配筋设计结果差异。结果表明:《公规》和《铁规》的抗震设计框架和内容基本一致,在具体规定上如E2或罕遇地震设计最大加速度响应值以及桥墩强度和延性验算方法等方面不同;D类桥梁《铁规》地震力明显大于《公规》,C类和B类桥梁《铁规》和《公规》地震力相当;地震力相同时,《铁规》配筋率计算值大于《公规》,因《铁规》配筋设计基于容许应力法,而《公规》基于极限状态法。 相似文献
19.
Uneven distribution of seismic demand in asymmetric-plan structures is a critical concern in earthquake-resistant design. Contemporary seismic design strategies that are based on linear elastic response, single load reduction factor, and uniform ductility demand throughout an asymmetric system generally lead to unsatisfactory performance in terms of realized ductilities and nonuniform damage distribution due to strong torsional coupling associated with asymmetric-plan systems. In many cases, actual nonlinear behavior of the structure displays significant deviation from what is estimated by a linear elastic, force-based seismic design approach. This study investigates the prediction of seismic demand distribution among structural members of a single-story, torsionally stiff asymmetric-plan system. The focus is on the effect of inherent unbalanced overstrength, resulting from current force-based design practices, on the seismic response of code-designed single-story asymmetric structures. The results obtained are utilized to compile unsymmetrical response spectra and uniform ductility spectra, which are proposed as assessment and preliminary design tools for estimating the seismic performance of multistory asymmetric structures. A simple design strategy is further suggested for improving the inelastic torsional performance of asymmetric systems. Providing additional strength to stiff edge members over their nominal design strength demands leads to a more balanced ductility distribution. Finally, seismic responses of several asymmetric case study structures designed with the aid of the proposed strategy are assessed for validating their improved performance. 相似文献
20.
This paper summarizes the results of an extensive study on the inelastic seismic response of X‐braced steel buildings. More than 100 regular multi‐storey tension‐compression X‐braced steel frames are subjected to an ensemble of 30 ordinary (i.e. without near fault effects) ground motions. The records are scaled to different intensities in order to drive the structures to different levels of inelastic deformation. The statistical analysis of the created response databank indicates that the number of stories, period of vibration, brace slenderness ratio and column stiffness strongly influence the amplitude and heightwise distribution of inelastic deformation. Nonlinear regression analysis is employed in order to derive simple formulae which reflect the aforementioned influences and offer a direct estimation of drift and ductility demands. The uncertainty of this estimation due to the record‐to‐record variability is discussed in detail. More specifically, given the strength (or behaviour) reduction factor, the proposed formulae provide reliable estimates of the maximum roof displacement, the maximum interstorey drift ratio and the maximum cyclic ductility of the diagonals along the height of the structure. The strength reduction factor refers to the point of the first buckling of the diagonals in the building and thus, pushover analysis and estimation of the overstrength factor are not required. This design‐oriented feature enables both the rapid seismic assessment of existing structures and the direct deformation‐controlled seismic design of new ones. A comparison of the proposed method with the procedures adopted in current seismic design codes reveals the accuracy and efficiency of the former. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献