首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
We evaluated controls on locations of channel incision, variation in channel evolution pathways and the time required to reconnect incised channels to their historical floodplains in the Walla Walla and Tucannon River basins, northwestern USA. Controls on incision locations are hierarchically nested. A first‐order geological control defines locations of channels prone to incision, and a second‐order control determines which of these channels are incised. Channels prone to incision are reaches with silt‐dominated valley fills, which have sediment source areas dominated by loess deposits and channel slopes less than 0·1(area)?0·45. Among channels prone to incision, channels below a second slope–area threshold (slope = 0·15(area)?0·8) did not incise. Once incised, channels follow two different evolution models. Small, deeply incised channels follow Model I, which is characterized by the absence of a significant widening phase following incision. Widening is limited by accumulation of bank failure deposits at the base of banks, which reduces lateral channel migration. Larger channels follow Model II, in which widening is followed by development of an inset floodplain and aggradation. In contrast to patterns observed elsewhere, we found the widest incised channels upstream of narrower reaches, which reflects a downstream decrease in bed load supply. Based on literature values of floodplain aggradation rates, we estimate recovery times for incised channels (the time required to reconnect to the historical floodplain) between 60 and 275 years. Restoration actions such as allowing modest beaver recolonization can decrease recovery time by 17–33 per cent. Published in 2007 by John Wiley & Sons, Ltd.  相似文献   

2.
Streams can be classified as stable or unstable, depending on the stage of channel evolution. Many streams of the southern Piedmont in United States have high sediment loads and are listed as impaired under the total maximum daily load (TMDL) program and may be unstable. It is not clear as to what the target (reference) load or remediation measures should be for unstable streams. The objective of this study was to determine the relative channel stability for a typical southern Piedmont stream using rapid geomorphic assessments (RGAs) and sediment yield analysis. The results were supported through a sediment fingerprinting analysis. RGAs were performed along 52 reaches on the North Fork Broad River (NFBR) main stem and two tributaries. Annual sediment yields were calculated and compared with yields in the southern Piedmont for stable streams that are resilient to degradation or aggradation and unstable streams that are susceptible to such disturbances. Majority of the NFBR main stem was found to be unstable with signs of geomorphic instability in the form of degradation and aggradation. The estimated average annual sediment yield was 0·78 T ha?1 year?1. By comparison, the median annual yield is 0·20 T ha?1 year?1 for stable streams and 0·48 T ha?1 year?1 for unstable streams in the Piedmont ecoregion with comparable drainage basin size. We conclude that the NFBR is in an unstable stage of channel evolution. Sediment fingerprinting proved that majority of the stream‐suspended sediment emanated from eroding stream channels. The methods outlined in this study have implications for the reference condition and remediation efforts related to stream turbidity and stream channel restoration. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

3.
Human‐induced changes to the channel and 18·6 km2 catchment of Second Creek, in Knox County, Tennessee (USA), have included deliberate channel realignment, channelization of some reaches in culverts or cement‐lined channels, the addition of coarse particles, and intentional and unintentional changes in catchment hydrology. Field observations and measurements made between 1997 and 2001 showed active adjustment of the stream channel. Channel bank erosion is the dominant adjustment, but aggradation also occurs. One change following urbanization is an increase in bed particle size due to the addition of particles of anthropogenic origin. Such particles constitute 2–21 per cent of particles sampled at eight sites along the stream, and their D50 exceeds the D50 of natural particles at five of the sites. The downstream portion of the catchment has been urbanized for more than 150 years, but urbanizing activity has continued throughout the catchment, occurring not as a discrete perturbation, but as a set of disturbances with varying spatial and temporal scales. Spatial patterns of erosion and deposition in the channel are complex and do not show an upstream–downstream trend. Effective, although unintended, decoupling of the most manipulated reaches has hindered the propagation of changes in channel morphology and channel materials in this urbanized stream system. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

4.
Over the last century, geomorphic processes along the Middle Rio Grande have been altered by flood control and bank stabilization projects, intensified land and water use, and climate change. In response to potential risks to infrastructure and ecological integrity, recent (1985–2008) adjustment was investigated and historic (1918–1985) changes in Rio Grande channel planform through the Albuquerque, New Mexico, area were reviewed, especially in relation to changes in annual peak discharge and river engineering measures. Using a GIS, channel characteristics were digitized from georeferenced photographs and analyzed with particular attention to quantifying potential measurement error and its propagation. Error associated with average channel widths and channel area ranged between 4 and 13%. For smaller polygons, e.g. islands, error was higher (11 to 40% for width and >200% for area) because width error is large relative to polygon width. Between 1918 and 1963, average channel widths decreased 8 m/yr, from 516 ± 67 m to 176 ± 7 m, mostly due to decreasing peak flows and the implementation of flood control and other engineering measures. From 1985 to 2008, widths decreased 0·7 m/yr, from 176 ± 23 m to 146 ± 5 m, accompanied by an increase in vegetated island area which largely coincided with low flow periods. Narrowing was concentrated at tributary inputs and in the upstream part of the reach, where bedload trapping by Cochiti Dam has caused degradation. Bank protection structures and dense vegetation limit bank erosion in the reach, but erosion is significant where expanding islands, incision, and increased meandering force water against banks. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

5.
The response of 12 fluvial fans near Sydney, Australia to a large storm between 2 and 4 February 1990 was determined by repeating previously surveyed longitudinal profiles and by undertaking detailed field observations of erosion and deposition. Peak rainfall intensities occurred on 3 and 4 February when between 173 and 193·8 mm were recorded. Return periods for 24 h duration peak rainfall ranged between 5·7 and 11·0 years on the annual maximum series at six stations within the study area and return periods for 48 h peak rainfall ranged between 13·5 and 29·4 years. Of the 12 fans, seven were trenched and five untrenched. The most significant geomorphic effects of the storm were recorded on the proximal region of the fans. However, fan response was highly variable, with one fan exhibiting no detectable change, three fans localized deposition, two fans spatially disjunct erosion and deposition, two fans channel avulsions, and seven fans fanhead trench reworking. Some fans exhibited more than one type of response. A four-stage, tentative cyclical model of fanhead development was constructed from the field data. Stage 1 refers to the episodic aggradation of the fanhead by localized deposition, spatially disjunct erosion and deposition and/or channel avulsions. Stage 2 represents the initiation of a fanhead trench when progressive aggradation locally exceeds a threshold slope leading to localized erosion. This erosion initially creates one or more discontinuous flow-aligned scour pools. Over time, the scour pools widen, deepen and extend both up- and downfan. Stage 3 refers to the coalescence of discontinuous scour pools into a continuous trench by the removal of intervening log and boulder steps. Stage 4 represents the backfilling phase of the trench once it has been overwidened and/or slope reduced. Aggradation then continues as for stage one.  相似文献   

6.
Predicting spatial and temporal variations in bank erosion due to extreme floods presents a long‐standing challenge in geomorphology. We develop two methodologies for rapid, regional‐scale assessments of stream reaches susceptible to channel widening. The first proposes that channel widening occurs when unit stream power exceeds a critical threshold (300 W/m2). The second is motivated by the observation that widening often occurs at channel bends. We introduce a new metric, the bend stress parameter, which is proportional to the centripetal force exerted on a concave bank. We propose that high centripetal forces generate locally high bank shear forces and enhance channel bank erosion. We test both metrics using the geomorphic signature of Tropical Storm Irene (2011) on the White and the Saxtons Rivers, Vermont. Specifically, we test if reaches where significant channel widening occurred during Irene required one or both metrics to exceed threshold values. We observe two distinct styles of channel widening. Where unit stream power and bend stress parameter are high, widening is usually due to bank retreat. Elsewhere widening is usually due to the stripping of the upstream end of mid‐channel islands. Excluding widening associated with the stripping of the heads of mid‐channel islands, almost all the widening (> 98%) occurred along reaches identified as susceptible to widening. The combined metrics identify up to one‐quarter of the reaches lacking susceptibility to channel widening. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

7.
We describe additions made to a multi‐size sediment routing model enabling it to simulate width adjustment simultaneously alongside bed aggradation/incision and fining/coarsening. The model is intended for use in single thread gravel‐bed rivers over annual to decadal timescales and for reach lengths of 1–10 km. It uses a split‐channel approach with separate calculations of flow and sediment transport in the left and right sides of the channel. Bank erosion is treated as a function of excess shear stress with bank accretion occurring when shear stress falls below a second, low, threshold. A curvature function redistributes shear stress to either side of the channel. We illustrate the model through applications to a 5·6‐km reach of the upper River Wharfe in northern England. The sediment routing component with default parameter values gives excellent agreement with field data on downstream fining and down‐reach reduction in bedload flux, and the width‐adjustment components with approximate calibration to match maximum observed rates of bank shifting give plausible patterns of local change. The approach may be useful for exploring interactions between sediment delivery, river management and channel change in upland settings. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

8.
Channel erosion along the Carmel river,Monterey county,California   总被引：1，自引：0，他引：1  
Historic maps, photographs, and channel cross-sections show that the channel of the Carmel River underwent massive bank erosion, channel migration, and aggradation in a major flood in 1911, then narrowed and incised by 1939. The channel was stable until 1978 and 1980, when bank erosion affected some reaches but not others. The narrowing and incision were in response to a lack of major floods after 1914 and construction in 1921 of a dam that cut off sediment supply from the most actively eroding half of the basin. Localized erosion in 1978 and 1980 occurred during low magnitude events along reaches whose bank strength had been reduced by devegetation. These events illustrate that the stability of a fluvial system can be disrupted either by application of a large erosive force in a high magnitude event (the 1911 flood) or in a low magnitude event, by reducing the resistance to erosion (bank devegetation). The Carmel River is a potentially unstable system. Its discharge and slope characteristics place it near the threshold between meandering and braided. On the Lower Carmel, the presence of bank vegetation can make the difference between a narrow, stable meandering channel and a wide shifting channel with braided reaches.  相似文献   

9.
Walker Creek in Marin County, California is a coastal stream draining to Tomales Bay, which lies in the San Andreas Rift Zone. Its valley contains an alluvial fill with a basal gravel dated at 5000 years BP. In upstream parts of the watershed, channels are incised arroyo-like in the fill leaving the valley floor standing as a high terrace averaging 5·5 m (18 ft) high. Below this terrace is an inner terrace of historic age that stands 2·4 m (8 ft) above the streambed. The stratigraphy and morphology of this valley are seen in others nearby, and indicate that in the last half of Holocene time in this region a single episode of valley alluviation was followed by two episodes of valley cutting. The second episode of valley cutting is occurring in the present time. During the last 60 years the flow has become seasonal, the stream has incised 1·5 m (5 ft) below the inner terrace in upstream reaches, aggraded 1·2 m (4 ft) in downstream reaches, and extended its estuary. Incision upstream has begun to re-expose the bedrock valley floor and is associated with aggradation downstream that has caused the flood plain to overtop both terraces. This has decreased the stream's gradient. Using a stream that is currently effecting major changes in its valley and channel morphology, two aspects of hydraulic adjustment in fluvial systems are examined. The changes in the average slope of the longitudinal profile are small but measureable. Profile concavity has not changed measurably. The various profiles that have existed in Holocene time show that stream gradient can be, but is not necessarily, slightly adjusted during valley filling and cutting. Flow measurements at a high discharge show that the channel has begun to assume the hydraulic geometry of an ephemeral channel. Adjustments of depth, velocity, and roughness appear to be hydraulic adjustments in response to changing watershed conditions.  相似文献   

10.
Along the lower reaches of the Waipaoa River, New Zealand, cross‐section survey data indicate there was a 23 per cent decrease in bankfull width and a 22 per cent reduction in channel cross‐section area between 1948 and 2000, as the channel responded to increased inputs of fine (suspended) sediment following deforestation of the headwaters in late C19 and early C20. We determined the bankfull discharge within a ～39 km long reach by routing known discharges through the one‐dimensional MIKE 11 flow model. The model runs suggest that the bankfull discharge varies between ～800 and ～2300 m3 s?1 and that the average recurrence interval is 4 ± 2 years on the annual maximum series; by contrast, the effective flow (360 m3 s?1) is equaled or exceeded three times a year. The variability in bankfull discharge arises because the banks tend to be lower in places where flood flows are constricted than in reaches where overbank flow is dispersed over a wide area, and because scour has counteracted aggradation in some locations. There is no downstream variation in Shields stress, or in relative shear stress, within the study reach. Bankfull shear stress is, on average, five times greater than the shear stress required to initiate motion. At the effective discharge it is more than twice the threshold value. The effective discharge probably has more relevance than the bankfull discharge to the overall picture of sediment movement in the lower reaches of the Waipaoa River but, because width is constrained by the stability and resistance of the bank material to erosion during high flows that also scour the bed, the overall channel geometry is likely determined by discharges at or near bankfull. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

11.
As a response to channelization projects undertaken near the turn of the 20th century and in the late 1960s, upstream reaches and tributaries of the Yalobusha River, Mississippi, USA, have been rejuvenated by upstream‐migrating knickpoints. Sediment and woody vegetation delivered to the channels by mass failure of streambanks has been transported downstream to form a large sediment/debris plug where the downstream end of the channelized reach joins an unmodified sinuous reach. Classification within a model of channel evolution and analysis of thalweg elevations and channel slopes indicates that downstream reaches have equilibrated but that upstream reaches are actively degrading. The beds of degrading reaches are characterized by firm, cohesive clays of two formations of Palaeocene age. The erodibility of these clay beds was determined with a jet‐test device and related to critical shear stresses and erosion rates. Repeated surveys indicated that knickpoint migration rates in these clays varied from 0·7 to 12 m a?1, and that these rates and migration processes are highly dependent upon the bed substrate. Resistant clay beds of the Porters Creek Clay formation have restricted advancement of knickpoints in certain reaches and have caused a shift in channel adjustment processes towards bank failures and channel widening. Channel bank material accounts for at least 85 per cent of the material derived from the channel boundaries of the Yalobusha River system. Strategies to reduce downstream flooding problems while preventing upstream erosion and land loss are being contemplated by action agencies. One such proposal involves removal of the sediment/debris plug. Bank stability analyses that account for pore‐water and confining pressures have been conducted for a range of hydrologic conditions to aid in predicting future channel response. If the sediment/debris plug is removed to improve downstream drainage, care should be taken to provide sufficient time for drainage of groundwater from the channel banks so as not to induce accelerated bank failures. Published in 2002 John Wiley & Sons, Ltd.  相似文献   

12.
Neck cutoffs and their resultant oxbow lakes are important and prominent features of riverine landscapes. Detailed field-based research focusing on the morphologic evolution of neck cutoffs is currently insufficient to fully characterize cutoff evolution. High-resolution bathymetric data were collected over 3 years for the purpose of determining channel morphology and morphologic change on three actively evolving neck cutoffs. Results indicate the following general trends in morphologic adjustment: (1) a longitudinal bar in the upstream meander limb that develops near the entrance to the abandoned bend; (2) a deep scour hole in the downstream meander limb immediately downstream of the cutoff channel; (3) erosion of the bank opposite the cutoff in the downstream meander limb; (4) a cutoff bar in the downstream meander limb at the junction corner of the cutoff channel and the downstream meander limb; and (5) perching of the exit of the abandoned bend above the cutoff channel due to channel bed incision. The results presented herein were used to develop a conceptual model that depicts the morphologic evolution of highly curving neck cutoffs. The findings of this research are combined with recent analyses of the three-dimensional flow structure through neck cutoffs to provide a mechanistic explanation for the morphodynamics of neck cutoffs. © 2019 John Wiley & Sons, Ltd.  相似文献   

13.
Two landsliding episodes between late 1973 and early 1975 delivered about 60000 m3 of sediment to six small deeply incised streams draining a 2·7 km2 area. About 4700 m3 of logs in the landslide debris formed major log jams in five streams, which impounded large volumes of landslide-derived sediment. Five years after the landsliding, 42 per cent (25000 m3) of sediment was still in storage behind 35 log jams ranging from 1·4–8·2 m high. The landsliding episodes have produced multi-stepped stream profiles, aggradation of channel reaches up to 150 m long to mean depths between 1·2 and 4·1 m, reductions in gradient, fining of bed material size, and related changes in bedforms and channel width:depth ratios that seem likely to persist for at least several decades. Sediment presently stored behind log jams is equivalent to between 50 and 220 years normal supply of sediment from hillslopes to stream channels. Long-delayed, large magnitude impacts on higher-order channels may occur if sudden failure of log jams is induced by a large storm at some future date.  相似文献   

14.
The impact of afforestation on stream bank erosion and channel form   总被引：1，自引：0，他引：1  
Modification of the land use of a small catchment through coniferous afforestation is shown to have influenced stream bank erosion and channel form. Field mapping and erosion pin measurements over a 19-month period provides evidence of more active bank erosion along forested channel reaches than along non-forested. Extrapolation of downstream increases in bankfull width, bankfull depth, and channel capacity with increasing basin area for the non-forested catchment has demonstrated that afforestation of the lower part of the catchment has had a marked effect on channel form. Channel widths within the forest are up to three times greater than that predicted from the regression. These changes in bankfull width have led to stream bed aggradation and the development of wide shallow channels within the forest, and channel capacities within the forest are over two times that predicted from the basin area. The relationship between channel sinuosity and valley gradient for non-forested reaches of the river also indicated decreased sinuosity resulting from afforestation. These changes in channel form result from active bank erosion within the forest with coarse material being deposited within the channel as point-bars and mid-channel bars. Active bank erosion is largely attributed to the suppression by the forest of a thick grass turf and its associated dense network of fine roots, and secondly to the river attempting to bypass log jams and debris dams in the stream channel.  相似文献   

15.
Tian Zhou  Ted Endreny 《水文研究》2012,26(22):3378-3392
River restoration projects have installed j‐hook deflectors along the outer bank of meander bends to reduce hydraulic erosion, and in this study we use a computational fluid dynamics (CFD) model to document how these deflectors initiate changes in meander hydrodynamics. We validated the CFD with streamwise and cross‐channel bankfull velocities from a 193° meander bend flume (inlet at 0°) with a fixed point bar and pool equilibrium bed but no j‐hooks, and then used the CFD to simulate changes to flow initiated by bank‐attached boulder j‐hooks (1st attached at 70°, then a 2nd at 160°). At bankfull and half bankfull flow the j‐hooks flattened transverse water surface slopes, formed backwater pools upstream of the boulders, and steepened longitudinal water slopes across the boulders and in the conveyance region off the mid‐channel boulder tip. Streamwise velocity and mass transport jets upstream of the j‐hooks were stilled, mid‐channel jets were initiated in the conveyance region, eddies with a cross‐channel axis formed below boulders, and eddies with a vertical axis were shed into wake zones downstream of the point bar and outer bank boulders. At half bankfull depth conveyance region flow cut toward the outer bank downstream of the j‐hook boulders and the secondary circulation cells were reshaped. At bankfull depth the j‐hook at 160° was needed to redirect bank‐impinging flow sent by the upstream j‐hook. The hooked boulder tip of both j‐hooks funneled surface flow into mid‐channel plunging jets, which reversed the secondary circulation cells and initiated 1 to 3 counter rotating cells through the entire meander. The main outer bank collision zone centered at 50° without the j‐hook was moved by the j‐hook to within and just beyond the 70° j‐hook boulder region, which displaced other mass transport zones downstream. J‐hooks re‐organized water surface slopes, streamwise and cross‐channel velocities, and mass transport patterns, to move shear stress from the outer bank and into the conveyance and mid‐channel zones at bankfull flow. At half bankfull flows a patch of high shear re‐attached to the outer bank below the downstream j‐hook. J‐hook geometry and placement within natural meanders can be analyzed with CFD models to help restoration teams reach design goals and understand hydraulic impacts. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

16.
Recent field and modeling investigations have examined the fluvial dynamics of confluent meander bends where a straight tributary channel enters a meandering river at the apex of a bend with a 90° junction angle. Past work on confluences with asymmetrical and symmetrical planforms has shown that the angle of tributary entry has a strong influence on mutual deflection of confluent flows and the spatial extent of confluence hydrodynamic and morphodynamic features. This paper examines three‐dimensional flow structure and bed morphology for incoming flows with high and low momentum‐flux ratios at two large, natural confluent meander bends that have different tributary entry angles. At the high‐angle (90°) confluent meander bend, mutual deflection of converging flows abruptly turns fluid from the lateral tributary into the downstream channel and flow in the main river is deflected away from the outer bank of the bend by a bar that extends downstream of the junction corner along the inner bank of the tributary. Two counter‐rotating helical cells inherited from upstream flow curvature flank the mixing interface, which overlies a central pool. A large influx of sediment to the confluence from a meander cutoff immediately upstream has produced substantial morphologic change during large, tributary‐dominant discharge events, resulting in displacement of the pool inward and substantial erosion of the point bar in the main channel. In contrast, flow deflection is less pronounced at the low‐angle (36°) confluent meander bend, where the converging flows are nearly parallel to one another upon entering the confluence. A large helical cell imparted from upstream flow curvature in the main river occupies most of the downstream channel for prevailing low momentum‐flux ratio conditions and a weak counter‐rotating cell forms during infrequent tributary‐dominant flow events. Bed morphology remains relatively stable and does not exhibit extensive scour that often occurs at confluences with concordant beds. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

17.
Intensive field monitoring of a reach of upland gravel‐bed river illustrates the temporal and spatial variability of in‐channel sedimentation. Over the six‐year monitoring period, the mean bed level in the channel has risen by 0·17 m with a maximum bed level rise of 0·5 m noted at one location over a five month winter period. These rapid levels of aggradation have a profound impact on the number and duration of overbank flows with flood frequency increasing on average 2·6 times and overbank flow time increasing by 12·8 hours. This work raises the profile of coarse sediment transfer in the design and operation of river management, specifically engineering schemes. It emphasizes the need for the implementation of strategic monitoring programmes before engineering work occurs to identify zones where aggradation is likely to be problematic. Exploration of the sediment supply and transfer system can explain patterns of channel sedimentation. The complex spatial, seasonal and annual variability in sediment supply and transfer raise uncertainties into the system's response to potential changes in climate and land‐use. Thus, there is a demand for schemes that monitor coarse sediment transfer and channel response. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

18.
Avulsion, the natural relocation of a river, is a key process in the evolution of subaerial fans, river floodplains and deltas. The causes of avulsion are poorly understood, which is partly due to the scarcity of field studies of present avulsions. At present, two avulsions are occurring on the middle and lower Taquari megafan, Pantanal basin, south‐western Brazil. Here we present an analysis of the causes of these avulsions based on field and remote sensing data and show that avulsions on megafans can be controlled by both upstream and downstream processes. The middle fan avulsion (started in 1997–1998) is a result of upstream control: overbank aggradation was caused by the (variable) input of sandy sediment into the system, which caused channel‐belt superelevation and also created an easily erodible subsurface favouring bank retreat, crevassing, and scour of deep floodplain channels. The sandy subsurface in this area is inferred to have been a major factor in the causation of this avulsion under conditions of little gradient advantage. The lower fan avulsion (started c. 1990) results from interplay of upstream and downstream controls, the latter being related to the local base level (the Paraguay River floodplain) at the toe of the fan. Channel and overbank aggradation on the lower fan was influenced by fan sub‐lobe progradation and channel backfilling. Fan sub‐lobe progradation caused a significant gradient advantage of the avulsion channel over the parent channel. Avulsions are commonly supposed to be preferentially triggered by high‐magnitude floods, when there is considerable channel‐belt superelevation. However, both avulsions studied by us were triggered by small to average floods, with modest channel‐belt superelevation. We conclude that flood magnitude and channel‐belt superelevation have been overrated as causes of avulsion, and demonstrate additional causes that influence the growth of crevasses into avulsions. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

19.
Flume experiments, in which the middle section of an erosion channel is displaced horizontally, have been conducted to assess the response of streams to horizontal displacement by a strike‐slip fault. The experimental erosion channel was developed in a mixture of sand and clay, which provided relatively stable banks with its cohesiveness. Horizontal displacement of a strike‐slip fault perpendicular to the channel is expected to add a ?at section to its longitudinal pro?le along the fault line. The experimental stream eliminated this ?at section with downstream degradation, upstream aggradation, and lateral channel shift. As a result, a roughly continuous longitudinal pro?le was maintained. This maintenance of a continuous longitudinal pro?le along channel is considered to be the principle of stream response to horizontal displacement by a strike‐slip fault. Downstream degradation was the dominant process of this stream response in the overall tendency of erosion without sand supply. When the rate of fault displacement was low (long recurrence interval), the experimental stream eroded the fault surface, jutting laterally into the channel like a scarp, and de?ected the channel within the recurrence interval. This lateral channel shift gave some gradient to the reach created by fault displacement (offset reach), and the downstream degradation occurred as much as completing the remaining longitudinal pro?le adjustment. When the rate of fault displacement was high (short recurrence interval), the lateral erosion on the ?rst fault surface was interrupted by the next fault displacement. The displacement was then added incrementally to the existing channel offset making channel shift by lateral erosion increasingly dif?cult. The channel offset with sharp bends persisted without much modi?cation, and downstream degradation and upstream aggradation became evident with the effect of the offset channel course, which worked like a dam. In this case, a slight local convexity, which was incidentally formed by downstream degradation and upstream aggradation, tended to remain in the roughly continuous longitudinal pro?le, as long as the horizontal channel offset persisted. In either case, once the experimental stream obtained a roughly continuous gradient, further channel adjustment seemed to halt. Horizontal channel offset remained to a greater or lesser extent at the end of each run long after the last fault displacement. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

20.
We modify a simple numerical stream‐pattern model to examine the effect of sediment stabilization by roots on the channel pattern of bedload rivers. In the model, vegetation enhances bank resistance to erosion, causing the development of a single channel instead of a rapidly changing, multiple channel (braided) pattern. Net aggradation resulting from a high sediment supply, however, causes frequent avulsions that destroy vegetation locally, leading to the development of a multiple‐channel pattern. A stability diagram representing multiple model runs predicts whether a river will exhibit single or multiple channels, based on plant‐enhanced bank strength, and on the time scale of plant development relative to a time scale for change in unvegetated channels. A second stability diagram predicts the way in which the amplitude and period of a fluctuating imposed sediment load influence whether a single or multiple‐channel pattern develops. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号