共查询到20条相似文献，搜索用时 46 毫秒
1.
2.
Robert Jankowski 《Bulletin of Earthquake Engineering》2003,1(3):397-403
The accurate analysis of the response of isolated structures requires the application of appropriate models of isolation devices.
The purpose of this paper is to analyse a nonlinear strain rate dependent model of a high damping rubber bearing which simulates
the horizontal behaviour of the device under specified vertical load using a nonlinear elastic spring-dashpot element. The
effectiveness of the model is checked by fitting the experimental data concerning three different rubber bearings. The results
of the study show that the model can simulate the bearing behaviour over a wide shear strain range with small simulation errors.
This revised version was published online in July 2006 with corrections to the Cover Date. 相似文献
3.
While isolation can provide significantly enhanced performance compared to fixed‐base counter parts in design level or even maximum considered level earthquakes, there is still uncertainty over the performance of isolation systems in extreme events. Researchers have looked at component level stability of rubber bearings and on the effect of moat impact on behavior of structures isolated on general bilinear isolators. However, testing of triple friction pendulum (TFP) sliding bearings has not been done dynamically or incorporated into a building system. Here, one‐third scale laboratory tests were conducted to on a 2‐story 2‐bay TFP‐isolated structure. Input motions were increasingly scaled until failure occurred at the isolation level. As the superstructure was designed with a yield force equivalent to the force of the bearing just at their ultimate displacement capacity, there was minimal yielding. A numerical model is presented to simulate the isolated building up to and including bearing failure. Forces transferred to the superstructure in extreme motions are examined using both experimental and numerical data. Additionally, the effect of the hardening stage of the TFP bearing is evaluated using the numerical model, finding slight benefits. 相似文献
4.
For the purpose of accurately predicting the seismic response of base-isolated structures, an analytical hysteresis model for elastomeric seismic isolation bearings is proposed. An extensive series of experimental tests of four types of seismic isolation bearings—two types of high-damping rubber bearings, one type of lead-rubber bearing and one type of silicon rubber bearing—was carried out with the objective of fully identifying their mechanical characteristics. The proposed model is capable of well-predicting the mechanical properties of each type of elastomeric bearing into the large strain range. Earthquake simulator tests were also conducted after the loading tests of the individual bearings. In order to show the validity of the proposed model, non-linear dynamic analyses were conducted to simulate the earthquake simulator test results. Good agreement between the experimental and analytical results shows that the model can be an effective numerical tool to predict not only the peak response value but also the force–displacement relationship of the isolators and floor response spectra for isolated structures. © 1997 by John Wiley & Sons, Ltd. 相似文献
5.
目前天然橡胶支座（NRB）的性能研究大多未考虑尺寸效应,在前期开展的近海桥梁隔震支座和材料老化时变规律研究的基础上,同时考虑支座直径尺寸变化和老化作用时间的影响对NRB的性能进行研究。首先采用ABAQUS有限元软件对不同直径尺寸NRB的性能进行分析,得到了NRB性能随直径尺寸的变化规律;然后结合前期老化作用对NRB及其橡胶材料性能时变规律的影响研究成果,分析了直径尺寸及老化作用时间共同作用下,NRB性能的变化规律,并通过ABAQUS有限元分析,验证了该变化规律的准确性。结果表明:NRB的水平刚度和竖向刚度均随其直径尺寸的增大呈正比例增大趋势;NRB水平刚度比和竖向刚度比均随老化作用时间的增长呈线性增大趋势;且直径为150mm的NRB在实际环境老化60a后,其水平刚度和竖向刚度的增长幅度分别为:30.8%和16.41%,由此可见老化作用时间对NRB水平刚度的影响较显著,对其竖向刚度的影响较小。研究内容可为隔震桥梁结构中支座缩尺模型试验的相关设计提供参考,并为将实验室缩尺橡胶隔震支座的相关成果较好地应用于实际工程计算及设计中提供依据。 相似文献
6.
低硬度橡胶隔震支座各种相关性及老化徐变特性 总被引：4，自引：1，他引：4
作者系统地对低硬度橡胶隔震支座的材料和力学性能进行了试验研究。研究使用的低硬度橡胶隔震支座分18种规格，总计近30个大直径隔震支座。研究内容涉及低硬度橡胶隔震支座的基本力学性能；温度、压力、剪切变形、老化和徐变等相关性；压缩界限，屈曲及极限剪切变形等界限性能以及橡胶材料性能和隔震工程应用等方面。本文主要介绍低硬度橡胶隔震支座的压力、剪切变形、温度对支座刚度、阻尼等力学性能的影响，同时还对隔震支座的老化及徐变特性进行了试验研究，确定低硬度橡胶使用60年后的力学性能变化率。文中同时提出了低硬度橡胶支座的温度修正方程，并提出了隔震结构地震反应分析时支座刚度和屈服荷载变化的取值范围。 相似文献
7.
Investigation of the seismic response of high‐rise buildings supported on tension‐resistant elastomeric isolation bearings 
下载免费PDF全文
下载免费PDF全文 In many applications of seismic isolation, such as in high‐rise construction, lightweight construction, and structures with large height‐to‐width aspect ratios, significant tension forces can develop in bearings, raising concerns about the possible rupture of elastomeric bearings and the uplift of sliding bearings. In this paper, a novel tension‐resistant lead plug rubber bearing (TLRB) with improved tension‐resisting capabilities is developed and experimentally and numerically assessed. This TLRB consists of a common lead plug rubber bearing (LRB) and several helical springs. After describing the theory underlying the behavior of the TLRB, the mechanical properties of reduced‐scale prototype bearings are investigated through extensive horizontal and vertical loading tests. The test results indicate that TLRBs can improve the shear stiffness and tension resistance capacity even under significant tensile loads. A series of shaking table tests on scaled models of high‐rise buildings with different aspect ratios were conducted to investigate the dynamic performance of the TLRB and the seismic responses of base‐isolated high‐rise buildings. Three different cases were considered in the shaking table tests: a fixed base condition and the use of TLRB and LRB isolation systems. The results of the shaking table test show that (a) base‐isolated systems are effective in reducing the structural responses of high‐rise buildings; (b) an isolated structure's aspect ratio is an important factor influencing its dynamic response; (c) TLRBs can endure large tensile stresses and avoid rupture on rubber bearings under strong earthquakes; and (d) the experimental and numerical results of the responses of the models show good agreement. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
8.
A finite element model is constructed for a sliding friction bearing in a seismically isolated bridge under vertical excitation with contact/friction elements. The effects of vertical excitation on the seismic performance of a seismically isolated bridge with sliding friction bearings and different bearing friction coefficients and different stiffness levels (pier diameter) are discussed using example calculations, and the effects of excitation direction for vertical excitation on the analysis results are explored. The analysis results shows that vertical excitation has a relatively large impact on seismic performance for a seismically isolated bridge with sliding friction bearings, which should be considered when designing a seismically isolated bridge with sliding friction bearings where vertical excitation dominates. 相似文献
9.
组合橡胶支座及橡胶支座与柱串联系统的水平刚度计算方法 总被引：11，自引：0，他引：11
目前基础隔震建筑中应用的叠层橡胶支座都是等截面的,其水平刚度是以遭遇强烈地震为依据设计的,当遭遇中小地震时水平刚度将偏大,致使上部结构的减震效果比遭遇设计地震时明显减小,而由两个不同截面橡胶支座组成的组合橡胶支座在不同强度地震时均能发挥较好设计的隔震效果。 相似文献
10.
This paper describes the results of shaking table tests to ascertain the ultimate behavior of slender base‐isolated buildings and proposes a time history response analysis method, which can predict the ultimate behavior of base‐isolated buildings caused by buckling fracture in laminated rubber bearings. In the tests, a base‐isolated structure model weighing 192 kN supported by four lead rubber bearings is used. The experimental parameters are the aspect ratio of height‐to‐distance between the bearings and the shape of and the axial stress on the bearings. The test results indicate that the motion types of the superstructure at large input levels can be classified into three types: the sinking type; the uplift type; and the mixed type. These behaviors depend on the relationship between the static ultimate lateral uplifting force on the superstructure and the lateral restoring characteristics of the base‐isolated story. In the analysis method, bearing characteristics are represented by a macroscopic mechanical model that is expanded by adding an axial spring to an existing model. Nonlinear spring characteristics are used for its rotational, shear, and axial spring. The central difference method is applied to solve the equation of motion. To verify the validity of the method, simulation analysis of the shaking table tests are carried out. The results of the analysis agree well with the test results. The proposed model can express the buckling behavior of bearings in the large deformation range. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
11.
高层隔震建筑设计中隔震支座受拉问题分析 总被引：11，自引：0，他引：11
高层建筑由于高宽比相对较大,倾覆效应明显,当采用隔震技术时,有可能使隔震支座出现拉应力,而通常使用的叠层橡胶隔震支座抗拉能力不强。因此,隔震支座受拉问题成为隔震技术在高层建筑中推广应用的主要障碍之一。本文提出了避免隔震支座受拉的上部结构布置原则及隔震层优化设计方法,并对目前隔震支座拉应力计算方法提出了改进建议。本文的研究工作可为工程设计提供借鉴,为隔震设计相关规范的修订提供依据。 相似文献
12.
Hirokazu Iemura Touraj Taghikhany Yoshikazu Takahashi Sarvesh K. Jain 《地震工程与结构动力学》2005,34(15):1777-1797
In this study, a series of shaking table tests are carried out on scaled models of two seismically isolated highway bridges to investigate the effect of rocking motion and vertical acceleration on seismic performance of resilient sliding isolators. In addition, performance of RSI is compared with system having solely natural rubber bearings. Test results show that variation of normal force on sliders due to rocking effect and vertical acceleration makes no significant difference in response of RSI systems. In addition, analytical response of prototype isolated bridge and the model used in experiments is obtained analytically by using non‐linear model for isolation systems. It is observed that for seismically isolated bridges, dynamic response of full‐scale complex structures can be predicted with acceptable accuracy by experiments using a simple model of the structure. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
13.
The response spectrum method has been widely used in earthquake engineering design, but cannot be directly applied to non-linear systems such as the lead-filled rubber bearing used in base isolation systems. An appraoch to determine the equivalent linearized stiffness and damping coefficient of the lead-filled rubber bearing by use of the results of shaking table tests is developed. Comparisons of time histories for the equivalent linear systems and the actual model show the method gives accurate maxima for displacement and acceleration and at the appropriate times. It is found that the identified parameters vary with the maximum deformation and the simplified formulae that can optimally describe the variations are derived. Using these formulae, an iterative algorithm using the response spectrum method to calculate the dynamic response of buildings isolated by lead-filled rubber bearings is also presented. 相似文献
14.
Elastomeric isolation bearings consist of multiple rubber layers with their top and bottom surfaces bonded to steel plates to restrict compressive deformation. Deformation constraints result in a variation of elastic modulus over the cross section of the rubber layers. In this paper, we describe a normalized compression modulus distribution on a circular rubber pad. The compressive and bending moduli of the rubber pad can be reproduced by applying the distribution to a series of axial springs. We also present a mechanical model for predicting the behavior of elastomeric seismic isolation bearings subject to large shear deformation and high compressive load. The mechanical model consists of a series of multiple shear springs at midheight and a series of axial springs at the top and bottom interfaces of the bearing. Simulation analyses of bearing tests were conducted to validate the proposed model. The analyses demonstrated that a model for circular lead-rubber bearings can successfully capture the influence of the axial load magnitude on the bearing shear behavior. The new model can simulate much more realistic behavior than prior models based on a uniform modulus assumption. 相似文献
15.
An advanced analytical model for high damping rubber bearings 总被引：1，自引：0，他引：1
Base‐isolation technologies have been developed over the years in attempts to mitigate the effects of earthquakes on structures and potentially vulnerable contents in earthquake prone areas of the world. The high damping rubber bearing (HDRB) is a relatively recent and evolving technology of this kind. The isolator shifts the fundamental period of the base‐isolated structure to a value beyond the range of the plentiful energy‐containing periods of earthquake motions and supplies significant damping to dissipate energy caused by motions. Nevertheless, the highly non‐linear mechanical behaviour of the HDRB is so complex, especially at large strains, that it is difficult to model it analytically. In this paper, an extensive study of experimental tests for identifying the mechanical characteristics of the HDRB is presented. By modifying the Wen's model to include the rate‐dependent effects, an advanced analytical model in an incremental form for the HDRB is also proposed. A very good agreement between the analytical and experimental results has been obtained. It is illustrated that the proposed mathematical model can predict well the mechanical behaviour of HDRB bearings, even at large shear strain. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
16.
为评估隔震和非隔震支座对桥梁地震易损性的影响,以一座3跨连续混凝土箱梁桥为分析对象,首先建立采用铅芯橡胶隔震支座与非隔震型盆式橡胶支座下桥梁的数值模型,求得不同程度地震作用下墩顶与支座的最大位移响应;再定义转角延性比损伤指标,结合支座剪应变,分析桥墩和支座的地震易损性情况;最后通过宽界限法建立全桥地震易损性曲线。研究结果表明,支座是较容易发生损坏的构件,而桥梁系统比桥墩或支座更易发生破坏,同时铅芯橡胶支座的破坏概率明显低于非隔震型盆式支座,可见采用隔震支座能有效减小桥墩墩顶在地震作用下的最大位移,此时桥墩地震易损性优于采用非隔震支座的情况。 相似文献
17.
An analytical model for high damping elastomeric isolation bearings is presented in this paper. The model is used to describe mathematically the damping force and restoring force of the rubber material and bearing. Ten parameters to be identified from cyclic loading tests are included in the model. The sensitivity of the ten parameters in affecting the model is examined. These ten parameters are functions of a number of influence factors on the elastomer such as the rubber compound, Mullins effect, scragging effect, frequency, temperature and axial load. In this study, however, only the Mullins effect, scragging effect, frequency and temperature are investigated. Both material tests and shaking table tests were performed to validate the proposed model. Based on the comparison between the experimental and the analytical results, it is found that the proposed analytical model is capable of predicting the shear force–displacement hysteresis very accurately for both rubber material and bearing under cyclic loading reversals. The seismic response time histories of the bearing can also be captured, using the proposed analytical model, with a practically acceptable precision. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
18.
A new isolation interface is proposed in this study to retrofit existing buildings with inadequate soft stories as well as new structures to be constructed with soft first story intended for architectural or functional purposes. The seismic interface is an assembly of bearings set in parallel on the top of the first story columns: the multiple‐slider bearings and rubber bearings. The multiple‐slider bearing is a simple sliding device consisting of one horizontal and two inclined plane sliding surfaces based on polytetrafluoroethylene and highly polished stainless steel interface at both ends set in series. A numerical example of a five‐story reinforced concrete shear frame with soft first story is considered and analyzed to demonstrate the efficiency of the proposed isolation system in reducing the ductility demand and damage in the structure while maintaining the superstructure above the bearings to behave nearly in the elastic range with controlled bearing displacement. Comparative study with the conventional system as well as various isolation systems such as rubber bearing interface and resilient sliding isolation is carried out. Moreover, an optimum design procedure for the multiple‐slider bearing is proposed through the trade‐off between the maximum bearing displacement and the first story ductility demand ratio. The results of extensive numerical analysis verify the effectiveness of the multiple‐slider bearing in minimizing the damage from earthquake and protecting the soft first story from excessively large ductility demand. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
19.
A modal procedure for non-linear analysis of multistorey structures with high-damping base-isolation systems was proposed. Two different isolation devices were considered in the analysis: an high-damping laminated rubber bearing and a lead-rubber bearing. Starting from deformational properties verified by tests, the isolation systems were characterized using three different analytical models (an Elastic Viscous, a Bilinear Hysteretic and a Wen's Model) with parameters depending from maximum lateral strain. After non-linear modelling of isolation and lateral-force-resisting systems, the effects of material non-linearities were considered as pseudo-forces applied to the equivalent linear system (Pseudo-Force Method) and the formally linearized equations of motion were uncoupled by the transformation defined by the complex mode shapes. The modal responses were finally obtained with an extension of Nigam–Jennings technique to non-linear and non-classically damped systems, in conjunction with an iterative technique searching for non-linear contributions satisfying equations of motion and constitutive laws. Since the properties of the isolated structure usually change with maximun lateral strain of isolation bearings, the integration of a new set of governing equations was required for each design-displacement value. The procedure proposed was described in detail and then applied for the determination of modal and total seismic responses in some real cases. At first, a very good agreement between non-linear responses obtained with the proposed mode superposition and with a direct integration method was observed. Then a comparison of results obtained with the three different analytical models of the isolation bearings was carried out. At last, the exact modal response obtained with analytical models depending from the design displacement of the isolation bearings was compared with two different approximated solutions, evaluated using mode shapes and isolation properties, respectively, calculated under simplified hypothesis.© 1998 John Wiley & Sons, Ltd. 相似文献
20.
Experimental study of the effect of restraining rim design on the extreme behavior of pendulum sliding bearings 下载免费PDF全文
下载免费PDF全文 《地震工程与结构动力学》2018,47(4):906-924
While the performance of sliding isolators has been extensively validated under typical levels of ground motion, there have been very few experimental studies on the extreme behavior of sliding isolation bearings when the displacement limit is reached. However, to appropriately design isolated systems, from selecting the displacement capacity of the bearing to sizing the superstructure members, the behavior of the bearing as it reaches, and in some cases exceeds, the displacement limit should be well understood. A series of shake table tests to investigate the extreme behavior of double pendulum sliding bearings under strong ground motions were conducted at McMaster University. One major difference in sliding bearings around the world is how the motion of the bearing is restrained at the bearing's displacement capacity. Scaled bearings with four different types of restraining rim designs were included, representing typical sliding restraining rims found in Europe, Japan, and the United States. Experimental observation shows that the restraining rim has a significant influence on the extreme behavior of sliding isolation bearing. Key response parameters such as impact force and uplift are evaluated and compared between the different sliding bearing designs. While the bearing with no rim bearing imparts the lowest forces to the superstructure, it loses its functionality at a lower amplitude input than all the other rim types. For the other rim designs, the impact forces are significantly higher but they remained operational although damaged. 相似文献