共查询到18条相似文献，搜索用时 125 毫秒
1.
通过理论推导，分别给出了直接基于位移和直接基于位移可靠度两种抗震设计方法所求结构基底剪力与现行抗震规范所求结构基底剪力之比的数学表达式，分析了影响上述比值的主要因素及影响规律。 相似文献
2.
一种直接基于位移的结构抗震设计方法 总被引：1，自引：1，他引：0
利用我国现行抗震规范,直接根据结构的底层层间目标位移反向求取结构的底层层间屈服剪力;给出了该屈服剪力与结构基底剪力之比的数学表达式,初步分析了影响该比值的主要因素及其影响规律。在此基础上,提出了一种新的直接基于位移的结构抗震设计方法。最后,通过算例分析初步考察了该方法的可行性。 相似文献
3.
基于位移的概率极限状态设计 总被引：1，自引：0，他引：1
尽管近年来国内外学者提出了多种基于位移的抗震设计方法，但采用的与位移相关的反应谱大多是平均谱，设计过程可以看作是确定性的。基于位移的抗震设计应该建立在可靠度理论基础之上。利用作者在概率延性需求谱方面已有的研究成果和可靠度分析方法——验算点法，本文提出了根据基于位移的目标可靠指标直接进行结构设计的方法，并给出了设计流程图。为便于工程应用，在进行了大量分析计算之后，本文建议了基于位移的概率极限状态分项系数设计表达式，并确定了其中的分项系数。最后，本文对一8层框架结构采用建议的分项系数设计表达式进行了设计，并对有待于进一步研究的问题进行了简要分析。 相似文献
4.
钢框架结构直接基于位移抗震性能设计的非迭代法 总被引：1，自引：1，他引：0
为使直接基于位移的抗震性能设计方法更加简便准确,本文采用一种直接基于位移的非迭代抗震设计方法对钢框架结构进行设计。该方法首先考虑结构的非弹性反应确定等效弹性反应谱和弹塑性反应谱,并建立了使用Newmark-Hall变形折减系数的能力谱的明确表达式。采用能力-需求图方法,确定了结构需要的目标位移与延性、谱位移和谱加速度之间关系的明确表示式,得到结构的刚度和设计基底剪力,进而确定构件截面,完成结构设计。对五层两跨平面钢框架结构进行了直接基于位移的抗震性能设计,设计过程简便,无需迭代程序,不需画出反应谱,通过时程分析验证了设计结果的精确性。本文研究表明:直接基于位移的非迭代抗震设计方法是一种简便、高效、精确的抗震性能设计方法。 相似文献
5.
一种直接基于位移的抗震设计方法 总被引：1，自引：0，他引：1
马宏旺 《地震工程与工程振动》2007,27(2):45-50
与传统基于力的抗震设计方法相比,基于位移的抗震设计方法更适合实现基于性能抗震设计。本文在若干文献的基础上,提出了一种直接基于位移的抗震设计方法。该方法建立在结构屈服位移可由几何尺寸确定的基础上,根据不同水平地震作用下的目标设计位移,计算相应的延性系数,采用一定的Rμ-μ-Tn关系建立相应的非线性反应谱,以二折线模型模拟结构的性能曲线,然后根据结构不同的目标位移以及对应的非线性反应谱确定相应的有效周期,从中选择最小值作为设计结构的有效周期,根据有效周期计算结构的刚度,然后乘以屈服位移得到结构的屈服强度。根据结构屈服强度以及结构的超强系数,得到结构的设计基底剪力。该方法避免了设计中采用迭代计算,且一次设计就可以完成多水平设防的目的。 相似文献
6.
RC框架结构薄弱层的层间位移可靠度水平考察 总被引：2，自引：0，他引：2
讨论了钢筋混凝土框架结构层间极限变形角的近似概率特性,考察了大震作用下20余幢钢筋混凝土框架结构薄弱层的层间位移可靠度水平,从而为直接基于位移可靠度的抗震设计中层间目标位移可靠度的确定提供了一定依据。 相似文献
7.
8.
9.
考察了大震作用下安装速度相关型消能器结构的薄弱层层间位移可靠度指标增大系数与原无控结构薄弱层层间位移可靠度指标、第一振型附加阻尼比和粘弹性材料损耗因子之间的定量关系,提出了该类有控结构直接基于位移可靠度的抗震设计步骤。 相似文献
10.
本文指出,目前抗震规范里规定的设计方法不能正确地估计结构抗震的可靠度。作者用24个地震记录计算了1800个多层建筑的弹塑性地震反应,给出了多层建筑在地震作用下延伸率的分布密度。文中用结构的延伸率不大于某一极限值的概率表示结构抗震的可靠度,提出了一个根据对结构抗震可靠度的要求设计抗震结构的方法。用此法进行设计,可以求出结构遇到不同强度地震时的可靠度。如果在某一时期某一强度地震发生的概率为已知,结构总的抗震可靠度即可求出。最后,用本文给出的结果对现有建筑的抗震可靠度作了估计。 相似文献
11.
Gopal Adhikari Lorenza Petrini Gian Michele Calvi 《Bulletin of Earthquake Engineering》2010,8(4):897-919
The paper investigates the applicability of current direct displacement based seismic design (DDBD) procedure, developed by
Priestley and his coworkers, for straight long span bridges under transverse seismic excitation synchronous to all supports.
This category of bridges often possess some additional features such as massive tall piers, highly irregular distribution
of mass and stiffness due to unequal superstructure spans and pier heights, large deformation capacity etc. that are absent
in short-to-moderate span bridges for which DDBD has extensively been verified. It is shown that DDBD in its current form
is unable to capture both displacement and base shear demand when compared with nonlinear dynamic analysis results. Accordingly,
a simple mechanics based extension of the current procedure that takes into account the effect of pier mass while computing
base shear demand as well as a modal combination rule for estimating displacement demand is proposed and validated using a
series of parametric studies. The new procedure also allows engineer to allocate strength at the potential plastic hinge location
in more general terms. 相似文献
12.
13.
超高层结构地震剪力响应由振型分解反应谱法得到的结果经常不能满足规定的最小剪力系数要求。为此,文章简述剪力系数的概念和调整方法,以具有不同剪力系数的两个模型对比分析结构弹性、弹塑性地震响应差异,探讨剪力系数对超高层结构地震响应的影响。以通过强度和刚度调整使最小剪力系数满足规范要求的两个模型,分析不同调整方法引起的结构响应的合理性。结果表明:满足最小剪力系数的结构的弹性基底剪力大、层间位移角较小,结构的弹塑性位移响应也较小,受力状态优于不满足最小剪力系数的结构,安全性得到了提高。结构弹性倾覆力矩需求和弹塑性基底剪力按刚度调整大于按强度调整;结构弹塑性最大顶点位移和层间位移角响应相差不大,但出现刚度大\,层间位移角也大的与抗震理论相悖的情况;在满足抗震要求的情况下,构件的受力状态则是按强度调整更优,构件截面更加经济合理。 相似文献
14.
Yield frequency spectra and seismic design of code‐compatible RC structures: an illustrative example 
下载免费PDF全文
下载免费PDF全文 The seismic design of an eight‐story reinforced concrete space frame building is undertaken using a yield frequency spectra (YFS) performance‐based approach. YFS offer a visual representation of the entire range of a system's performance in terms of the mean annual frequency (MAF) of exceeding arbitrary global ductility or displacement levels versus the base shear strength. As such, the YFS framework can establish the required base shear and corresponding first‐mode period to satisfy arbitrary performance objectives for any structure that may be approximated by a single‐degree‐of‐freedom system with given yield displacement and capacity curve shape. For the eight‐story case study building, deformation checking is the governing limit state. A conventional code‐based design was performed using seismic intensities tied to the desired MAF for safety checking. Then, the YFS‐based approach was employed to redesign the resulting structure working backwards from the desired MAF of response (rather than intensity) to estimate an appropriate value of seismic intensity for use within a typical engineering design process. For this high‐seismicity and high‐importance midrise building, a stiffer system with higher base shear strength was thus derived. Moreover, performance assessment via incremental dynamic analysis showed that while the code‐design did not meet the required performance objective, the YFS‐based redesign needed only pushover analysis results to offer a near‐optimal design outcome. The rapid convergence of the method in a single design/analysis iteration emphasized its efficiency and practicability as a design aid for practical application. Copyright © 2017 John Wiley & Sons, Ltd. 相似文献
15.
Geoffrey W. Rodgers John B. Mander J. Geoffrey Chase Kerry J. Mulligan Bruce L. Deam Athol Carr 《地震工程与结构动力学》2007,36(1):77-100
Semi‐active dampers offer significant capability to reduce dynamic wind and seismic structural response. A novel resetable device with independent valve control laws that enables semi‐active re‐shaping of the overall structural hysteretic behaviour has been recently developed, and a one‐fifth scale prototype experimentally validated. This research statistically analyses three methods of re‐shaping structural hysteretic dynamics in a performance‐based seismic design context. Displacement, structural force, and total base‐shear response reduction factor spectra are obtained for suites of ground motions from the SAC project. Results indicate that the reduction factors are suite invariant. Resisting all motion adds damping in all four quadrants and showed 40–60% reductions in the structural force and displacement at the cost of a 20–60% increase in total base‐shear. Resisting only motion away from equilibrium adds damping in quadrants 1 and 3, and provides reductions of 20–40%, with a 20–50% increase in total base‐shear. However, only resisting motion towards equilibrium adds damping in quadrants 2 and 4 only, for which the structural responses and total base‐shear are reduced 20–40%. The spectral analysis results are used to create empirical reduction factor equations suitable for use in performance based design methods, creating an avenue for designing these devices into structural applications. Overall, the reductions in both response and base‐shear indicate the potential appeal of this semi‐active hysteresis sculpting approach for seismic retrofit applications—largely due to the reduction of the structural force and overturning demands on the foundation system. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
16.
17.
本文通过弹性和弹塑性时程分析,研究了水平地震作用下梁铰型屈服RC框架模型结构的楼层屈服剪力系数、基本自振周期、楼层数3个因素对弹塑性位移增大系数的影响,通过非线性回归分析给出了弹塑性层间位移增大系数经验公式;通过分析滞回耗能沿楼层高度的分布,初步确定了梁铰型屈服RC框架结构的薄弱楼层位置;基于结构损伤分析,讨论了抗震规范中RC框架结构弹塑性层间位移角限值的水准。 相似文献
18.
Seismic rotational displacement of gravity walls by pseudo-dynamic method: Passive case 总被引：8，自引：0，他引：8
Prediction of the seismic rotational displacements of retaining wall under passive condition is an important aspect of design in earthquake prone region. In this paper, the pseudo-dynamic method is used to compute the rotational displacements of rigid retaining wall supporting cohesionless backfill under seismic loading for the passive earth pressure condition. The proposed method considers time, phase difference and effect of amplification in shear and primary waves propagating through both the backfill and the retaining wall. The influence of ground motion characteristics on rotational displacement of the wall is evaluated. Also the effects of variation of parameters like wall friction angle, soil friction angle, amplification factor, shear wave velocity, primary wave velocity, period of lateral shaking, horizontal and vertical seismic accelerations on the rotational displacements are studied. The rotational displacement of the wall increases substantially with increase in amplification of both shear and primary waves, time of input motion, period of lateral shaking and decreases with increase in soil friction angle, wall friction angle. The rotational displacements of the wall also increase when the effect of wall inertia is taken into account. Results are provided in graphical form. 相似文献