共查询到20条相似文献，搜索用时 459 毫秒
1.
2017年5月11日新疆塔什库尔干5.5级地震给震区建筑结构造成了不同程度破坏。选择震区钢筋混凝土（RC）框架结构、砖混结构以及土石木结构等3类典型建筑结构,介绍了各类建筑结构地震破坏特点,分析了震害特征与破坏机理。结果表明:RC框架结构在地震中表现出了优异的抗震性能,即使在震中区,破坏也仅仅表现为非结构性破坏,如填充墙开裂和吊顶脱落等;砖混结构绝大多数抗震性能优良,仅震中区的少数建筑物发生了承重墙墙体开裂情况;土石木结构房屋抗震性能最差,地震破坏最为严重,是导致该次地震人员伤亡主要原因。建议地震高烈度设防区房屋建筑应采用抗震性能较好的RC框架结构和砖混结构,而抗震性能差的土石木建筑房屋应尽量避免继续建设和使用。结果可供类似地区房屋建设和建筑结构抗震设计等工作参考。 相似文献
2.
This paper proposes a new analytical model for masonry‐infilled R/C frames to evaluate the seismic performance considering R/C frame–infill interactions. The proposed analytical model replaces masonry infill with a diagonal compression strut, which represents distributed compression transferred between frame and infill interfaces. The equivalent strut width is presented as a function of the frame–infill contact length, which can be evaluated by static equilibriums related to compression balance and lateral displacement compatibility at the frame–infill interfaces. The proposed analytical model was verified through comparisons with experimental results obtained for several brick masonry‐infilled R/C frames representing a typical R/C building with nonstructural masonry infill in Indonesia. As a result, good agreements were observed between the experimental and analytical values of the lateral strength and ductility of the infilled frames. The seismic performances of two earthquake‐damaged R/C buildings with different damage conditions were evaluated considering infill effects by applying the proposed analytical model. Consequently, the nonstructural brick masonry infill significantly affected the seismic resistances of the buildings, which seemed to lead to differing levels of damage for each building. These results indicate that the proposed analytical model can be an effective tool for more precisely screening earthquake‐vulnerable existing R/C buildings in Indonesia. Copyright © 2016 The Authors. Earthquake Engineering & Structural Dynamics Published by John Wiley & Sons Ltd. 相似文献
3.
One of the main challenges in earthquake risk mitigation is the assessment of existing buildings not designed according to modern codes and the development of effective techniques to strengthen these structures. Particular attention should be given to RC frame structures with masonry infill panels, as demonstrated by their poor performance in recent earthquakes in Europe. Understanding the seismic behaviour of masonry‐infilled RC frames presents one of the most difficult problems in structural engineering. Analytical tools to evaluate infill–frame interaction and the failure mechanisms need to be further studied. This research intends to develop a simplified macro‐model that takes into account the out‐of‐plane behaviour of the infill panels and the corresponding in‐plane and out‐of‐plane interaction when subjected to seismic loadings. Finally, a vulnerability assessment of an RC building will be performed in order to evaluate the influence of the out‐of‐plane consideration in the building response. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
4.
Masonry buildings are often characterized by geometric irregularities. In many cases, such buildings meet global regularity requirements provided by seismic codes, but they are composed by irregular walls with openings. The latter are masonry walls characterized by (i) openings of different sizes, (ii) openings misaligned in the horizontal and/or vertical direction, or (iii) a variable number of openings per story. An irregular layout of openings can induce not only a nonuniform distribution of gravity loads among masonry piers but also unfavorable damage localizations resulting in a premature collapse of the wall and hence a higher seismic vulnerability. This paper is aimed at providing a simplified methodology to assess the effects of irregularities on the in‐plane seismic capacity of unreinforced masonry (URM) walls with openings. To this end, a macroelement method was developed and validated through experimental results available in the literature. The proposed methodology was based on the quantification of wall irregularities by means of geometric indices and their effects on seismic capacity of URM walls with openings through both sensitivity and regression analyses. Sensitivity analysis was based on a high number of static pushover analyses and allowed to assess variations in key seismic capacity parameters. Regression analysis let to describe each capacity parameter under varying irregularity index, providing empirical models for seismic assessment of irregular URM walls with openings. The in‐plane seismic capacity was found to be significantly affected by wall irregularities, especially in the case of openings with different heights. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
5.
Paulo B. Lourenço João M. Leite Manuel F. Paulo‐Pereira A. Campos‐Costa P. X. Candeias Nuno Mendes 《地震工程与结构动力学》2016,45(14):2241-2260
Several factors influence the behaviour of infilled frames, which have been a subject of research in the past with moderate success. The new generation of European design standards imposes the need to prevent brittle collapse of the infills and makes the structural engineer accountable for this requirement, yet it fails to provide sufficient information for masonry infills design. Therefore, the present work aims at understanding the seismic behaviour of masonry infill walls within reinforced concrete frames, using both unreinforced and reinforced solutions (bed joint reinforcement and reinforced plaster). For this purpose, three reinforced concrete buildings with different infill solutions were constructed at a scale of 1:1.5, all with the same geometry, and were tested on the shaking table of the National Laboratory for Civil Engineering, Portugal. All solutions performed adequately for the design earthquake, with no visible damage. Still, the experimental tests show that the double‐leaf‐unreinforced infill walls underperformed during a large earthquake, collapsing out of plane by rotating as rigid bodies with multiple configurations. Also the reinforced concrete buildings collapsed, because of the adverse interaction with the infill walls. The infill walls with bed joint reinforcement and reinforced plaster did not collapse out of plane, because of their connection to the concrete frame, which is an essential requirement. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
6.
An indexing method for rapid evaluation of the seismic vulnerability of infi lled RC frame buildings in Jordan is proposed. The method aims at identifying low and medium rise residential buildings as safe or in need of further detailed evaluation. Following a rapid visual screening, the building is assigned a Basic Capacity Index(BCI); fi ve performance modifi ers are identifi ed and multiplied by the BCI to arrive at the Capacity Index(CI) of the building. A Capacity Index lower than a limit CI value indicates that the screened building could experience moderate earthquake damage whereas a higher value implies that minor damage, if any, would take place. To establish the basic evaluation parameters; forty RC frame buildings were selected, designed and analyzed using static nonlinear analysis and incorporating the effect of infi ll walls. Effects of seismicity, local site conditions, horizontal irregularities(setbacks and re-entrant corners), vertical irregularities(soft story at ground fl oor level) and overhangs on the seismic performance of local buildings were examined. Assessment forms were designed and used to evaluate and rank 112 sample buildings. About 40% of the surveyed buildings were found to be in need of detailed evaluation to better defi ne their seismic vulnerabilities. 相似文献
7.
Study on the effect of the infill walls on the seismic performance of a reinforced concrete frame 总被引：1，自引：0，他引：1
Motivated by the seismic damage observed to reinforced concrete (RC) frame structures during the Wenchuan earthquake, the effect of infill walls on the seismic performance of a RC frame is studied in this paper. Infill walls, especially those made of masonry, offer some amount of stiffness and strength. Therefore, the effect of infill walls should be considered during the design of RC frames. In this study, an analysis of the recorded ground motion in the Wenchuan earthquake is performed. Then, a numerical model is developed to simulate the infill walls. Finally, nonlinear dynamic analysis is carried out on a RC frame with and without infill walls, respectively, by using CANNY software. Through a comparative analysis, the following conclusions can be drawn. The failure mode of the frame with infill walls is in accordance with the seismic damage failure pattern, which is strong beam and weak column mode. This indicates that the infill walls change the failure pattern of the frame, and it is necessary to consider them in the seismic design of the RC frame. The numerical model presented in this paper can effectively simulate the effect of infill walls on the RC frame. 相似文献
8.
Irregular reinforced concrete (RC) buildings constitute a significant portion of the existing housing stock. A common type of irregularity is in the form of discontinuity in the vertical framing elements, which can exacerbate their seismic vulnerability. The design guidelines available in seismic design codes essentially cater to only regular buildings, and the safety of such buildings, even when the other guidelines of the codes are followed, is doubtful. This article evaluates the vulnerability of RC frame buildings with discontinuity in columns designed for modern seismic codes, in the form of seismic collapse capacity, collapse resistance against maximum earthquake demand level, and failure mechanism. The adequacy and limitations of the provisions of the seismic design codes are evaluated for such buildings. Analysis results show that the sequential analysis of buildings considering the construction staged effects, considerably affects the design and hence the collapse failure mechanism of even low- and mid-rise buildings. The results also underline the importance of strong column–weak beam design in the seismic performance of the floating column buildings. The vertical component of ground motion is also observed to be relatively more crucial in floating column buildings. 相似文献
9.
Hemchandra Chaulagain Hugo Rodrigues Enrico Spacone Humberto Varum 《地震工程与工程振动(英文版)》2016,15(2):251-268
Reinforced concrete (RC) buildings in Nepal are constructed with RC frames and masonry infill panels. These structures exhibit a highly non-linear inelastic behavior resulting from the interaction between the panels and frames. This paper presents an extensive case study of existing RC buildings in Nepal. Non-linear analyses were performed on structural models of the buildings considered as a bare frame and with masonry infill, in order to evaluate the influence of infill walls on the failure mechanisms. Five three-storey buildings with different structural configurations and detailing were selected. The effect of masonry infill panels on structural response was delineated by comparing the bare-framed response with the infill response. Seismic performance is evaluated with regard to global strength, stiffness, energy dissipation, inter-storey drift, and total deflection of the structure. A parametric analysis of structures with masonry infill is also performed. For this, the influence of different material properties is studied, namely diagonal compressive stress, modulus of elasticity and tensile stress of masonry infill panels. Study results show that masonry infill increases the global strength and stiffness of the structures; it decreases the inter-storey drift and hence the total displacement of the structure. The results quantify the influence of the infill panels on structural response and, in particular, the effect of the diagonal compressive strength of the masonry wall. 相似文献
10.
Masonry buildings are primarily constructed out of bricks and mortar which become discrete pieces and cannot sustain horizontal forces created by a strong earthquake.The collapse of masonry walls may cause significant human casualties and economic losses.To maintain their integrity,several methods have been developed to retrofit existing masonry buildings,such as the constructional RC frame which has been extensively used in China.In this study,a new method using precast steel reinforced concrete(PSRC)panels is developed.To demonstrate its effectiveness,numerical studies are conducted to investigate and compare the collapse behavior of a structure without retrofitting,retrofitted with a constructional RC frame,and retrofitted with external PSRC walls(PSRCW).Sophisticated finite element models(FEM)were developed and nonlinear time history analyses were carried out.The results show that the existing masonry building is severely damaged under occasional earthquakes,and totally collapsed under rare earthquakes.Both retrofitting techniques improve the seismic performance of existing masonry buildings.However,it is found that several occasional earthquakes caused collapse or partial collapse of the building retrofitted with the constructional RC frame,while the one retrofitted by the proposed PSRC wall system survives even under rare earthquakes.The effectiveness of the proposed retrofitting method on existing masonry buildings is thus fully demonstrated. 相似文献
11.
为研究填充墙对底层框架多层砌体房屋地震反应的影响,以典型的填充墙-底层框架多层砌体房屋为基础,建立有限元计算模型并进行了弹塑性动力时程分析。根据不同模型的计算结果以及填充墙的刚度和强度,分析了填充墙对底层框架多层砌体房屋自振周期、地震作用下房屋整体变形、底层框架的损伤以及填充墙与底层框架相互作用的影响。计算结果表明：填充墙对房屋整体地震反应产生明显影响,其影响不能忽略。在上部砌体结构质量和刚度不变的情况下,结构自振周期随着填充墙刚度的增加而降低;随着填充墙与底层框架之间连接作用的增强,结构整体的变形减小,底层框架的损伤增大。当填充墙与底层框架之间采用弱连接时,采用强度较高的填充墙可以提高结构整体的变形能力,从而提高结构整体的抗震能力。 相似文献
12.
Francesco Longo Lydell Wiebe Francesca da Porto Claudio Modena 《Bulletin of Earthquake Engineering》2018,16(12):6163-6190
Experimental tests have shown that unreinforced masonry (URM) infill walls are affected by simultaneous loading in their in-plane and out-of-plane directions, but there have been few attempts to represent this interaction in nonlinear time history analysis of reinforced concrete (RC) buildings with URM infill walls. In this paper, a recently proposed macro-model that accounts for this interaction is applied to the seismic analysis of RC framed structures with URM infill walls representative of Mediterranean building stock and practices. Two RC framed structures that are representative of low and mid-rise residential buildings are analysed with a suite of a bidirectional ground motions, scaled to three different intensities. During the analyses, the in-plane/out-of-plane interaction is monitored, showing that cracking of the infills occurs predominantly by in-plane actions, while failure occurs due to a combination of in-plane and out-of-plane displacements, with the out-of-plane component usually playing the dominant role. Along the frame height, the bottom storeys are generally the most damaged, especially where thin infill walls are used. These results are consistent with observations of damage to URM infill walls in similar buildings during recent earthquakes. 相似文献
13.
Unreinforced masonry (URM) infill panels are widely used as partitions in RC frames and typically considered as non‐structural elements in the design process. However, observations from recent major earthquakes have shown that under seismic excitation, the structural interaction between columns and infill walls can significantly alter the structural behaviour, thus causing catastrophic consequences. The purpose of this research was to propose and test an innovative low seismic damage detailing method, which isolates the infill panel from bounding columns with finite width vertical gaps during the infill panel construction phase and deploys steel wire connections in mortar layers anchored to columns. Taking into account the similitude requirements, a total of six one‐third scale, single‐storey single‐bay RC frames with different infill configurations and flexible connection details were carefully designed and tested on a shake‐table. Three real earthquake records were selected and scaled to ascending intensity levels and used as input signals. A series of thorough investigations including dynamic characteristics, hysteretic behaviour, failure mechanisms, out‐of‐plane vulnerabilities and the effect of different gap filling materials and load transfer mechanisms were rigorously studied. The experimental results indicate that the undesirable interaction between infill panels and bounding frame is significantly reduced using the proposed low seismic damage detailing concept. Direct shear failure of columns at an early stage is prevented, and structural redundancy at high levels of excitation can be provided. In general, the structural stability and integrity, and displacement ductility of infilled RC frames can remarkably be improved. Copyright © 2017 John Wiley & Sons, Ltd. 相似文献
14.
为进一步改善框架结构平面内和平面外抗震性能,本文提出带X形斜撑的新型砌体填充墙构造方案,并进行了4榀蒸压加气混凝土砌块砌体填充墙框架结构试验,以研究墙体构造措施和墙-框连接方式对框架结构抗震性能的影响。首先进行平面内水平低周往复荷载试验,随后进行历经平面内损伤的平面外单调静力加载试验,最后进行承载力、刚度退化和耗能能力等抗震性能指标的分析。结果表明:墙-框柔性连接方案下,填充墙框架结构的平面内及平面外水平承载力和初始刚度均小于刚性连接方案,而变形能力、耗能能力和位移延性等性能指标均比刚性连接表现更好;墙-框柔性连接且填充墙带X形斜撑框架结构的平面内及平面外抗震性能指标均有明显改善,更有利于抗震。 相似文献
15.
隔震器与填充墙对建筑抗震性能有很大作用。为了探究填充墙布置形式及填充材料和隔震器协同作用对钢筋混凝土框架结构动力特性及抗震性能的影响,采用等效斜撑理论,对3种不同填充墙布置形式与隔震器协同作用的抗震系统方案进行对比分析,研究发现顶层不布置填充墙与隔震器协同抗震系统钢筋混凝土框架结构的抗震性能最佳。在此系统上分析了不同填充材料对钢筋混凝土框架结构抗震性能的影响,结果表明,加气混凝土砌块填充墙的钢筋混凝土框架结构抗震性能最好。 相似文献
16.
《地震研究进展（英文）》2023,3(1):100180
The report summarizes the observed damage to a variety of buildings near the epicenter of the M6.8 Luding earthquake in Sichuan Province, China. They include base-isolated buildings, multi-story reinforced concrete (RC) frame buildings, and masonry buildings. The near-field region is known to be tectonically highly active, and the local intensity level is the highest, that is, 0.4g peak ground acceleration (PGA) for the design basis earthquake, in the Chinese zonation of seismic ground motion parameters. The extent of damage ranged from the weak-story collapse that claimed lives to the extensive nonstructural damage that suspended occupancy. The report highlights the first observation of the destruction of rubber bearings and viscous dampers in the isolation layer of Chinese seismically isolated buildings. It also features the rare observation of the brittle shear failure of RC columns in moment-resisting frames in a region of such a high seismic design requirement. Possible reasons that may have attributed to the reported damage are suggested by providing facts observed in the field. However, careful forensic analyses are needed before any conclusive judgment can be made. 相似文献
17.
The damage to the masonry-infilled reinforced concrete (RC) frame buildings in Charikot, the capital city of Dolakha district in Nepal, during the 2015 April-to-May Nepal earthquake sequence is reported. Most of these buildings were built by the owners with little governmental inspections regarding their structural design or constructional quality. Although they generally performed better than other structural systems such as stone-masonry houses, the RC frames sustained extensive damage ranging from cracking of infill to complete collapse. In particular, eight of the 72 inspected RC frames alongside an uphill street collapsed in different ways. In addition to the un-engineered nature of these RC frames, their collapse could also be attributed to multiple technical reasons including the effect of terrain, the pounding between adjacent buildings and the accumulative damage in the earthquake sequence. 相似文献
18.
Numerous research studies have proved that numerical models aiming at an accurate evaluation of the seismic response of RC framed buildings cannot ignore the inelastic behaviour of infills and the interaction between infill and frame elements. To limit the high computational burden of refined non-linear finite element models, in the latest decades, many researchers have developed simplified infill models by means of single or multiple strut-elements. These models are low time-consuming and thus adequate for static and dynamic analyses of multi-storey structures. However, their simulation of the seismic response is sometimes unsatisfying, particularly in the presence of infill walls with regular or (particularly) irregular distributions of openings. This paper presents a new 2D plane macro-element, which provides a refined simulation of the non-linear cyclic response of infilled framed structures at the expense of a limited computational cost. The macro-element consists of an articulated quadrilateral panel, a single 1D diagonal link, and eight 2D links and is able to model the shear and flexural behaviour of the infill and the non-linear flexural/sliding interaction between infill and surrounding frame. The proposed macro-element has been implemented into the open source software OpenSees and used to simulate the response of single-storey, single-span RC infilled frame prototypes tested by other authors. The above prototypes are selected as made of different masonry units and characterised by full or open geometric configuration. 相似文献
19.
Earthquake-induced building collapse and progressive collapse due to accidental local failure of vertical components are the two most common failure modes of reinforced concrete (RC) frame structures. Conventional design methods usually focus on the design requirements of a specific hazard but neglect the interactions between different designs. For example, the progressive collapse design of an RC frame often yields increased reinforcement and flexural strength of the beams. As a result, the seismic design principle of “strong-column-weak-beam” may be violated, which may lead to unfavorable failure modes and weaken the seismic performance. To avoid these adverse effects of the progressive collapse design on the seismic resistance of RC frames, a novel structural detailing is proposed in this study. The proposed detailing technique intends to concurrently improve the seismic and progressive collapse performances of an RC frame by changing the layout of the newly added longitudinal reinforcement against progressive collapse without introducing any additional reinforcement. A six-story RC frame is used as the prototype building for this investigation. Both cyclic and progressive collapse tests are conducted to validate the performance of the proposed structural detailing. Based on the experimental results, detailed finite element (FE) models of the RC frame with different reinforcement layouts are established. The seismic and progressive collapse resistances of different models are compared based on the incremental dynamic analysis (IDA) and nonlinear dynamic alternate path (AP) methods, respectively. The results indicate that the proposed structural detailing can effectively resolve the conflict between the seismic and progressive collapse designs. 相似文献
20.
On 3 August 2014, the Ludian earthquake struck northwest Yunnan Province with a surface wave magnitude of 6.5. This moderate earthquake unexpectedly caused high fatalities and great economic loss. Four strong motion stations were located in the areas with intensity V, VI, VII and IX, near the epicentre. The characteristics of the ground motion are discussed herein, including 1) ground motion was strong at a period of less than 1.4 s, which covered the natural vibration period of a large number of structures; and 2) the release energy was concentrated geographically. Based on materials collected during emergency building inspections, the damage patterns of adobe, masonry, timber frame and reinforced concrete (RC) frame structures in areas with different intensities are summarised. Earthquake damage matrices of local buildings are also given for fragility evaluation and earthquake damage prediction. It is found that the collapse ratios of RC frame and confined masonry structures based on the new design code are significantly lower than non-seismic buildings. However, the RC frame structures still failed to achieve the ‘strong column, weak beam’ design target. Traditional timber frame structures with a light infill wall showed good aseismic performance. 相似文献