共查询到20条相似文献，搜索用时 15 毫秒
1.
以美国西部地区某斜交公路连续刚构桥为研究对象，研究其不等高墩易损性差异以及斜交角的改变对桥墩地震易损性的影响。考虑桥梁结构参数和地震动的不确定性，选取100条地震动，沿纵桥向输入，生成"结构-地震动"样本库，以地震动峰值加速度（PGA）为强度指标（IM），利用OpenSees软件对结构进行非线性时程分析得到桥墩动力响应，而后以桥墩曲率延性比衡量桥梁破坏状态，在确定桥墩损伤指标的基础上，采用可靠度理论得到各桥墩的地震易损性曲线，判断桥墩的损伤模式、损伤特点。在此基础上，改变桥梁斜交角度进行易损性分析，得到斜交角变化对桥墩地震易损性的影响。研究表明：该桥最矮墩发生损伤的概率大于其他桥墩，桥墩最先进入塑性的是墩顶和墩底区域；不同斜交角对桥墩的地震响应影响显著，各墩损伤破坏排序与斜交桥结构构造特点有关，同一排架墩的两侧墩柱易损性呈现与角度变化趋势相反的排列，损伤越严重，趋势越明显；对于此不等高的斜交刚构桥，最矮墩为其抗震薄弱环节，斜交角越大，越应该关注钝角处矮墩的损伤情况，并提高其设计标准，在进行斜交刚构桥抗震设计中应予以重视。 相似文献
2.
为研究强地震作用下,桥台及台后土体对斜交连续梁桥抗震作用的影响。以一座三跨连续斜交箱梁桥为依托,应用sap2000建立不同斜度的模型,针对有、无桥台两种工况,采用非线性时程分析方法,研究了纵向不同地震动强度输入下,桥台及台后土体作用对不同斜度的连续梁桥主梁和桥墩位移的影响规律,并对桥墩的延性性能进行分析。研究结果表明:桥台及台后土体的存在会抑制主梁的纵向位移,大大增加主梁梁端的横向位移,地震动幅值越大,这种作用越明显;桥台及台后土体作用会减小墩顶纵向位移和墩底纵向弯矩,降低桥墩纵向位移延性需求,提高桥墩纵向安全性,斜交角越大,该影响效果越小;桥台作用对桥墩的横向反应几乎无影响。建议在桥梁抗震设计时应考虑桥台以及台后土体的作用,并针对不同斜度的连续梁桥采取相应的抗震措施,以提高其抗震性能。 相似文献
3.
Abutment behavior significantly influences the seismic response of certain bridge structures. Specifically in the case of short bridges with relatively stiff superstructures typical of highway overpasses, embankment mobilization and inelastic behavior of the soil material under high shear deformation levels dominate the response of the bridge and its column bents. This paper investigates the sensitivity of bridge seismic response with respect to three different abutment modeling approaches. The abutment modeling approaches are based on three increasing levels of complexity that attempt to capture the critical components and modes of abutment response without the need to generate continuum models of the embankment, approach, and abutment foundations. Six existing reinforced concrete bridge structures, typical of Ordinary Bridges in California, are selected for the analysis. Nonlinear models of the bridges are developed in OpenSees. Three abutment model types of increasing complexity are developed for each bridge, denoted as roller, simplified, and spring abutments. The roller model contains only single-point constraints. The spring model contains discrete representations of backfill, bearing pad, shear key, and back wall behavior. The simplified model is a compromise between the efficient roller model and the comprehensive spring model. Modal, pushover, and nonlinear dynamic time history analyses are conducted for the six bridges using the three abutment models for each bridge. Comparisons of the analysis results show major differences in mode shapes and periods, ultimate base shear strength, as well as peak displacements of the column top obtained due to dynamic excitation. The adequacy of the three abutment models used in the study to realistically represent all major resistance mechanisms and components of the abutments, including an accurate estimation of their mass, stiffness, and nonlinear hysteretic behavior, is evaluated. Recommendations for abutment modeling are made. 相似文献
4.
Nonlinear static (pushover) analysis has become a popular tool during the last decade for the seismic assessment of buildings. Nevertheless, its main advantage of lower computational cost compared to nonlinear dynamic time‐history analysis (THA) is counter‐balanced by its inherent restriction to structures wherein the fundamental mode dominates the response. Extension of the pushover approach to consider higher modes effects has attracted attention, but such work has hitherto focused mainly on buildings, while corresponding work on bridges has been very limited. Hence, the aim of this study is to adapt the modal pushover analysis procedure for the assessment of bridges, and investigate its applicability in the case of an existing, long and curved, bridge, designed according to current seismic codes; this bridge is assessed using three nonlinear static analysis methods, as well as THA. Comparative evaluation of the calculated response of the bridge illustrates the applicability and potential of the modal pushover method for bridges, and quantifies its relative accuracy compared to that obtained through other inelastic methods. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
5.
W.Phillip Yen 《地震工程与工程振动(英文版)》2009,8(1):127-135
Conventional seismic evaluation of existing bridges explores the ability of a bridge to survive under significant earthquake excitations. This approach has several major drawbacks, such as only a single structural performance of near collapse is considered, and the simplified approach of adopting strength-based concept to indirectly estimate the nonlinear behavior of a structure lacks accuracy. As a result, performance-based concepts that include a wider variety of structural performance states of a given bridge excited by different levels of earthquake intensity is needed by the engineering community. This paper introduces an improved process for the seismic evaluation of existing bridges. The relationship between the overall structural performance and earthquakes with varying levels of peak ground acceleration (PGA) can successfully be linked. A universal perspective on the seismic evaluation of bridges over their entire life-cycle can be easily obtained to investigate multiple performance objectives. The accuracy of the proposed method, based on pushover analysis, is proven in a case study that compares the results from the proposed procedure with additional nonlinear time history analyses. 相似文献
6.
能力谱方法在桥梁抗震性能评估中的应用研究 总被引：1，自引：0，他引：1
位移延性是桥梁抗震性能的重要指标之一,以Pushover分析为基础的能力谱方法能够考察结构在地震下的弹塑性位移响应,是抗震性能评估的一种有效手段.文中阐述了能力谱法的基本原理,说明了基于弹塑性反应谱的能力谱方法在求解性能点时不需要进行迭代计算;基于弹性设计反应谱建立了相对应的弹塑性反应谱,结合某实桥,将能力谱方法和增量动力分析方法进行了对比,并根据不同的地震基本烈度和场地土类型进行了抗震性能评估.分析认为,能力谱方法计算简便,对结构1阶振型的地震响应占主导时,具有较好的精度,并能够基于设计反应谱来考察结构的弹塑性抗震性能,可用于桥梁抗震性能的评估. 相似文献
7.
Pushover分析方法的发展及其在桥梁结构中的应用 总被引：1，自引：0，他引：1
非线性静力分析方法（Pushover分析方法）可以较好地检验结构的变形能力,找到结构的薄弱环节,控制强烈地震作用下结构破坏程度,对工程设计有很强的指导意义。但目前Pushover分析方法的种类很多,各自有着不同的优缺点和适用范围,针对桥梁结构,阐述静力非线性分析方法（Pushover）的原理及其研究发展概况,评述了各种Pushover方法的优缺点,并分析了Pushover方法用于桥梁结构的基本原理和评价方法,指出Pushover方法用于桥梁结构存在的问题。 相似文献
8.
Abdoul R. Ghotbi 《地震工程与工程振动(英文版)》2014,13(3):357-373
The seismic behavior of skewed bridges has not been well studied compared to straight bridges. Skewed bridges have shown extensive damage, especially due to deck rotation, shear keys failure, abutment unseating and columnbent drift. This research, therefore, aims to study the behavior of skewed and straight highway overpass bridges both with and without taking into account the effects of Soil-Structure Interaction(SSI) due to near-fault ground motions. Due to several sources of uncertainty associated with the ground motions, soil and structure, a probabilistic approach is needed. Thus, a probabilistic methodology similar to the one developed by the Pacific Earthquake Engineering Research Center(PEER) has been utilized to assess the probability of damage due to various levels of shaking using appropriate intensity measures with minimum dispersions. The probabilistic analyses were performed for various bridge confi gurations and site conditions, including sand ranging from loose to dense and clay ranging from soft to stiff, in order to evaluate the effects. The results proved a considerable susceptibility of skewed bridges to deck rotation and shear keys displacement. It was also found that SSI had a decreasing effect on the damage probability for various demands compared to the fixed-base model without including SSI. However, deck rotation for all types of the soil and also abutment unseating for very loose sand and soft clay showed an increase in damage probability compared to the fixed-base model. The damage probability for various demands has also been found to decrease with an increase of soil strength for both sandy and clayey sites. With respect to the variations in the skew angle, an increase in skew angle has had an increasing effect on the amplitude of the seismic response for various demands. Deck rotation has been very sensitive to the increase in the skew angle; therefore, as the skew angle increased, the deck rotation responded accordingly. Furthermore, abutment unseating showed an increasing trend due to an increase in skew angle for both fixed-base and SSI models. 相似文献
9.
Effects of spatially variable ground motions on the seismic response of a skewed, multi-span, RC highway bridge 总被引：4，自引：0，他引：4
This paper presents a study of the influence of spatially variable ground motions on the longitudinal seismic response of a short, three-span, 30-degree skewed, reinforced concrete highway bridge. Linear and nonlinear finite element models are created for the bridge and linear elastic and nonlinear inelastic time history analyses conducted. Three different types of illustrative excitations are considered: The first utilizes spatially variable ground motions incorporating the effects of variable soil conditions, loss of coherency and wave passage as input motions at the structures' supports. The time history with the smallest peak displacement and the one with the largest peak displacement from the spatially variable ones are then used as uniform input motions at all bridge supports. The comparative analysis of the bridge model shows that the uniform ground motion input with the largest peak displacement cannot provide conservative seismic demands for all structural components—in a number of cases it results in lower response than that predicted by spatially variable motions. The present results indicate that there is difficulty in establishing uniform input motions that would have the same effect on the response of bridge models as spatially variable ones. Consequently, spatially variable input motions need to be applied as excitations at the bridge supports. 相似文献
10.
11.
12.
13.
Nonlinear FE model updating and reconstruction of the response of an instrumented seismic isolated bridge to the 2010 Maule Chile earthquake 
下载免费PDF全文
下载免费PDF全文 Nonlinear finite element (FE) modeling has been widely used to investigate the effects of seismic isolation on the response of bridges to earthquakes. However, most FE models of seismic isolated bridges (SIB) have used seismic isolator models calibrated from component test data, while the prediction accuracy of nonlinear FE models of SIB is rarely addressed by using data recorded from instrumented bridges. In this paper, the accuracy of a state‐of‐the‐art FE model is studied through nonlinear FE model updating (FEMU) of an existing instrumented SIB, the Marga‐Marga Bridge located in Viña del Mar, Chile. The seismic isolator models are updated in 2 phases: component‐wise and system‐wise FEMU. The isolator model parameters obtained from 23 isolator component tests show large scatter, and poor goodness of fit of the FE‐predicted bridge response to the 2010 Mw 8.8 Maule, Chile Earthquake is obtained when most of those parameter sets are used for the isolator elements of the bridge model. In contrast, good agreement is obtained between the FE‐predicted and measured bridge response when the isolator model parameters are calibrated using the bridge response data recorded during the mega‐earthquake. Nonlinear FEMU is conducted by solving single‐ and multiobjective optimization problems using high‐throughput cloud computing. The updated FE model is then used to reconstruct response quantities not recorded during the earthquake, gaining more insight into the effects of seismic isolation on the response of the bridge during the strong earthquake. 相似文献
14.
Ioannis F. Moschonas Andreas J. Kappos Panagiotis Panetsos Vissarion Papadopoulos Triantafyllos Makarios Pavlos Thanopoulos 《Bulletin of Earthquake Engineering》2009,7(2):439-468
This study focusses on the estimation of seismic fragility curves for all common bridge types found in modern greek motorways.
At first a classification scheme is developed in order to classify the existing bridges into a sufficient number of classes.
A total of 11 representative bridge classes resulted, based on the type of piers, deck, and pier-to-deck connection. Then
an analytical methodology for deriving fragility curves is proposed and applied to the representative bridge models. This
procedure is based on pushover analysis of the entire bridge and definition of damage states in terms of parameters of the
bridge pushover curves. The procedure differentiates the way of defining damage according to the seismic energy dissipation
mechanism in each bridge, i.e. bridges with yielding piers of the column type and bridges with bearings (with or without seismic
links) and non-yielding piers of the wall type. The activation of the abutment-backfill system due to closure of the gap between
the deck and the abutments is also taken into account. The derived fragility curves are subjected to a first calibration against
empirical curves based on damage data from the US and Japan. 相似文献
15.
The present study evaluates seismic resilience of highway bridges that are important components of highway transportation systems. To mitigate losses incurred from bridge damage during seismic events, bridge retrofit strategies are selected such that the retrofit not only enhances bridge seismic performance but also improves resilience of the system consisting of these bridges. To obtain results specific to a bridge, a reinforced concrete bridge in the Los Angeles region is analyzed. This bridge was severely damaged during the Northridge earthquake because of shear failure of one bridge pier. Seismic vulnerability model of the bridge is developed through finite element analysis under a suite of time histories that represent regional seismic hazard. Obtained bridge vulnerability model is combined with appropriate loss and recovery models to calculate seismic resilience of the bridge. Impact of retrofit on seismic resilience is observed by applying suitable retrofit strategy to the bridge assuming its undamaged condition prior to the Northridge event. Difference in resilience observed before and after bridge retrofit signified the effectiveness of seismic retrofit. The applied retrofit technique is also found to be cost‐effective through a cost‐benefit analysis. First order second moment reliability analysis is performed, and a tornado diagram is developed to identify major uncertain input parameters to which seismic resilience is most sensitive. Statistical analysis of resilience obtained through random sampling of major uncertain input parameters revealed that the uncertain nature of seismic resilience can be characterized with a normal distribution, the standard deviation of which represents the uncertainty in seismic resilience. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
16.
桥梁作为交通系统中的生命线工程,其抗震性能问题尤为重要。桥梁减隔震技术主要通过减隔震装置来降低结构的地震损伤,目前已发展成为提高强震区桥梁抗震能力的重要措施。为促进减隔震技术在中国桥梁工程领域的进一步发展,首先总结减隔震桥梁的设计方法,归纳其地震反应和震害情况,对采用不同减隔震装置桥梁的非线性动力性能、减隔震效果、地震随机响应、易损性及性能优化方法等研究情况进行梳理;其次,概述减隔震技术在斜交桥、曲线桥及铁路桥梁中的应用情况与研究进展,并介绍新型韧性抗震设计理念在桥梁工程领域中的应用情况和发展前景;最后,总结减隔震桥梁的试验研究情况,指出目前减隔震桥梁研究中的不足和发展趋势。 相似文献
17.
针对斜交桥在破坏性地震中发生破坏和损伤的突出问题,采用铅芯橡胶支座(LRB)进行隔震和滞回耗能。基于OpenSees平台建立了不同斜度的传统非隔震和全桥采用LRB隔震的4跨斜交连续梁桥动力分析模型,沿2个水平方向输入远场地震动和具有向前方向性效应、滑冲效应以及无速度脉冲效应的近断层地震动,并进行非线性时程计算,研究桥墩和挡块的损伤状态、主梁旋转度、碰撞力与斜交桥斜度的关系以及LRB对斜交桥抗震性能的影响。结果表明:向前方向性效应和滑冲效应的脉冲型地震动作用下的斜交桥地震反应和损伤明显大于无速度脉冲近断层和远场地震动作用; 采用LRB隔震后,明显降低了固定墩的地震损伤,桥墩位移减震率可达到50%以上; LRB隔震桥主梁与挡块的间隙宜结合桥梁的地震风险和设计位移进行确定。 相似文献
18.
本文以一座三跨总长60 m的整体桥为案例桥,分别试设计了同跨径的半整体桥、延伸桥面板桥和常规连续梁桥。通过Midas/Civil软件建立四种桥型的有限元模型,并对其进行了E1和E2反应谱分析和时程分析,对比了四种桥型的结构反应峰值（墩顶位移、桥墩及桩基剪力与弯矩、台底位移、桥台桩基剪力与弯矩）。计算结果表明:当桥梁存在15°的斜交角,整体桥、半整体桥在地震动沿平行于桥台长边方向及其垂直方向输入时更不利,而延伸桥面板桥和常规连续梁桥在地震动沿顺桥向和横桥向输入时更不利。四种桥型在地震作用下:整体桥抗震性能最优异,但其台底位移、桥台桩基的剪力和弯矩最大;半整体桥台底位移、桥台桩基的剪力和弯矩最小,其墩顶位移、桥墩及桩基的剪力和弯矩仅比整体桥大;延伸桥面板桥和常规连续梁桥的墩-梁相对位移远大于整体桥和半整体桥,不适用于地震基本烈度高的区域。 相似文献
19.
Effects of structural characterizations on fragility functions of bridges subject to seismic shaking and lateral spreading 总被引：1，自引：0，他引：1
This paper evaluates the seismic vulnerability of different classes of typical bridges in California when subjected to seismic shaking or liquefaction-induced lateral spreading. The detailed structural configurations in terms of superstructure type, connection, continuity at support and foundation type, etc. render different damage resistant capability. Six classes of bridges are established based on their anticipated failure mechanisms under earthquake shaking. The numerical models that are capable of simulating the complex soil-structure interaction effects, nonlinear behavior of columns and connections are developed for each bridge class. The dynamic responses are obtained using nonlinear time history analyses for a suite of 250 earthquake motions with increasing intensity. An equivalent static analysis procedure is also implemented to evaluate the vulnerability of the bridges when subjected to liquefaction-induced lateral spreading. Fragility functions for each bridge class are derived and compared for both seismic shaking （based on nonlinear dynamic analyses） and lateral spreading （based on equivalent static analyses） for different performance states. The study finds that the fragility functions due to either ground shaking or lateral spreading show significant correlation with the structural characterizations, but differences emerge for ground shaking and lateral spreading conditions. Structural properties that will mostly affect the bridges＇ damage resistant capacity are also identified. 相似文献
20.
抗震销在上海莘庄立交工程的设计中,由于构造的特殊性,其力学特性难以用常规方法表达。基于位移和多级设防的抗震思想,以莘庄立交工程中的一异型板桥为例,首次以两个包含极端边界条件的结构分析模型考虑抗震销这一特殊构造措施对结构的影响,并按照实际结构构造充分考虑材料非线性及连接构件的非线性等因素,分别以弹塑性纤维梁柱单元、空间滑动支座单元和接触单元模拟桥墩屈服、支座滑动、相邻结构之间碰撞,建立了空间非线性时程反应分析模型,并进行了设计和罕遇地震水平两个概率水准下的地震反应分析和抗震性能评估,并根据分析结果的对比,提出强化抗震销刚度的建议。 相似文献