首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 26 毫秒
1.
This paper reviews the recent geophysical literature addressing the estimation of saturated hydraulic conductivity (K) from static low frequency electrical measurements (electrical resistivity, induced polarization (IP) and spectral induced polarization (SIP)). In the first part of this paper, research describing how petrophysical relations between electrical properties and effective (i.e. controlling fluid transport) properties of (a) the interconnected pore volumes and interconnected pore surfaces, have been exploited to estimate K at both the core and field scale is reviewed. We start with electrical resistivity measurements, which are shown to be inherently limited in K estimation as, although resistivity is sensitive to both pore volume and pore surface area properties, the two contributions cannot be separated. Efforts to utilize the unique sensitivity of IP and SIP measurements to physical parameters that describe the interconnected pore surface area are subsequently introduced and the incorporation of such data into electrical based Kozeny–Carman type models of K estimation is reviewed. In the second part of this review, efforts to invert geophysical datasets for spatial patterns of K variability (e.g. aquifer geometries) at the field-scale are considered. Inversions, based on the conversion of an image of a geophysical property to a hydrological property assuming a valid petrophysical relationship, as well as joint/constrained inversion methods, whereby multiple geophysical and hydrological data are inverted simultaneously, are briefly covered. This review demonstrates that there currently exists an opportunity to link, (1) the petrophysics relating low frequency electrical measurements to effective hydraulic properties, with (2) the joint inversion strategies developed in recent years, in order to obtain more meaningful estimates of spatial patterns of K variability than previously reported.  相似文献   

2.
The frequency dependence of complex electrical conductivity in the IP frequency range (10–3 to 103 Hertz) has been investigated for a variety of microcracked rocks from the German continental deep drilling project (KTB), Northern Bavaria. The laboratory measurements were made with a computer controlled four-electrode system on plugs saturated with brine of different salinity. It has been found that the complex nature of the conductivity is caused solely by the capacitive behaviour of the interlayer region between the solid matrix and the electrolytic pore solution. The resulting main feature of the conductivity spectra is a constant phase angle over the investigated frequency range combined with a nearly identical power law frequency dependence of the real as well as the imaginary parts. The low-frequency exponent is in the order of about 0 to 0.05. It is related to common IP-parameters. The relationships between the frequency exponent and microcrack properties are of special interest. The results of the study show that the frequency exponent is (1) proportional to the surface area to porosity ratio, (2) inversely proportional to water salinity, and (3) dependent on water composition. Complex conductivity measurements allow an uncomplicated separation of electrical volume and interface effects. Moreover, the results suggest that determination of specific surface area of microcracked rocks directly from complex electrical measurements can be made.  相似文献   

3.
We investigated the role of increasingly well‐constrained geologic structures in the subsurface (i.e., subsurface architecture) in predicting streambed flux and hyporheic residence time distribution (RTD) for a headwater stream. Five subsurface realizations with increasingly resolved lithological boundaries were simulated in which model geometries were based on increasing information about flow and transport using soil and geologic maps, surface observations, probing to depth to refusal, seismic refraction, electrical resistivity (ER) imaging of subsurface architecture, and time‐lapse ER imaging during a solute tracer study. Particle tracking was used to generate RTDs for each model run. We demonstrate how improved characterization of complex lithological boundaries and calibration of porosity and hydraulic conductivity affect model prediction of hyporheic flow and transport. Models using hydraulic conductivity calibrated using transient ER data yield estimates of streambed flux that are three orders of magnitude larger than uncalibrated models using estimated values for hydraulic conductivity based on values published for nearby hillslopes (10?4 vs. 10?7 m2/s, respectively). Median residence times for uncalibrated and calibrated models are 103 and 100 h, respectively. Increasingly well‐resolved subsurface architectures yield wider hyporheic RTDs, indicative of more complex hyporheic flowpath networks and potentially important to biogeochemical cycling. The use of ER imaging to monitor solute tracers informs subsurface structure not apparent from other techniques, and helps to define transport properties of the subsurface (i.e., hydraulic conductivity). Results of this study demonstrate the value of geophysical measurements to more realistically simulate flow and transport along hyporheic flowpaths.  相似文献   

4.
It is known that the time‐domain induced‐polarization decay curve for a shaly sand reservoir depends on the pore structure of the reservoir, and this curve can be used to estimate permeability, which is a determining factor in making production decisions in the petroleum industry. Compared with NMR logging tools, induced polarization has several advantages, such as a deep depth of investigation and a high signal‐to‐noise ratio. The purpose of this paper is to establish an appropriate model using induced polarization to estimate the permeability. The curve can be modelled as a weighted superposition of exponential relaxations. The plot of weight versus the relaxation time constant is defined as the relaxation time spectrum. Induced‐polarization decay‐curve measurements were performed on 123 samples from the Daqing oilfield using a four‐electrode technique. A singular‐value decomposition method was used to transform the induced‐polarization decay data into a spectrum. Different models to estimate the permeability were discussed. The results of the research indicate that the induced‐polarization measurements greatly improve the statistical significance of permeability correlations. Compared with the traditional forms, AφC and AFC, the forms, ATBφC and ATBFC, have lower error factors, where T, Φ and F are the geometric mean time constant of the induced‐polarization relaxation time spectrum, the porosity and the resistivity formation factor, respectively, and A, B and C are constants. The mean time constant is the decisive parameter in the permeability estimation and it is not completely independent of the resistivity formation factor. The additional use of the porosity and the resistivity formation factor leads to an appreciable improvement. It is concluded that this new model will make it possible to estimate the permeability of a shaly sand reservoir downhole.  相似文献   

5.
The inversion of induced‐polarization parameters is important in the characterization of the frequency electrical response of porous rocks. A Bayesian approach is developed to invert these parameters assuming the electrical response is described by a Cole–Cole model in the time or frequency domain. We show that the Bayesian approach provides a better analysis of the uncertainty associated with the parameters of the Cole–Cole model compared with more conventional methods based on the minimization of a cost function using the least‐squares criterion. This is due to the strong non‐linearity of the inverse problem and non‐uniqueness of the solution in the time domain. The Bayesian approach consists of propagating the information provided by the measurements through the model and combining this information with a priori knowledge of the data. Our analysis demonstrates that the uncertainty in estimating the Cole–Cole model parameters from induced‐polarization data is much higher for measurements performed in the time domain than in the frequency domain. Our conclusion is that it is very difficult, if not impossible, to retrieve the correct value of the Cole–Cole parameters from time‐domain induced‐polarization data using standard least‐squares methods. In contrast, the Cole–Cole parameters can be more correctly inverted in the frequency domain. These results are also valid for other models describing the induced‐polarization spectral response, such as the Cole–Davidson or power law models.  相似文献   

6.
Transport properties (permeability and electrical conductivity) have been measured at different hydrostatic pressure runs on 7 crystalline rocks (gneisses and amphibolites) sampled from the KTB drilling project. The decrease of permeability by pressure are compared with the pressure-dependent data of the electrical conductivity (formation factor) resulting from complex impedance measurements. According to the equivalent-channel model (ECM), there exists a linear relationship between these parameters by representing both properties on logarithmic scales. The results show that it is possible to extrapolate high-pressure permeability from low-pressure (< 60 MPa) permeability data by using the pressure-dependent electrical conductivity (up to 300 MPa).  相似文献   

7.
向阳  孙小龙  高小其  李娜 《中国地震》2017,33(4):563-574
基于新10井水位对九寨沟M_S7.0、精河M_S6.6地震的同震响应特征,分别利用水震波和潮汐分析法,反演得到了新10井水位在地震波作用期间和地震波作用前后含水层参数特征,探讨了2次地震引起的新10井同震响应变化机理。结果表明,新10井水位对九寨沟地震和精河地震具有不同的同震响应形态,利用水平流模型反演所得的新10井含水层渗透系数,在九寨沟地震时为61m/d,而在精河地震时为147m/d,表明地震波作用导致水平向的渗透性增强;利用垂向流模型反演得到的新10井含水层渗透系数,在2次地震之前约为49×10~(-5)m/d,而在地震之后约为18×10~(-5)m/d,表明地震波作用导致垂直向的渗透性减弱。因此,新10井水位的同震响应变化与地震波引起的含水层渗透率的改变有关。  相似文献   

8.
《水文科学杂志》2013,58(3):543-555
Abstract

The contact between freshwater and seawater in coastal aquifers is studied using a relatively simple model for homogeneous aquifers. However, for real aquifers it is not so simple. The desalination plant built to supply water to the city of Almería is situated over the aquifer in the southern part of the River Andarax Delta. Its design capacity is 1100 L s?1, and it is supplied from boreholes pumping water from beneath the freshwater—seawater contact in this aquifer. Well logs kept over a period of two years have allowed us to accurately define the interface geometry of the freshwater—seawater contact. Lithological data collected from 31 boreholes have also indicated the existence of strata with low hydraulic conductivity, within others of high conductivity. During a simultaneous pumping test of six wells with 690 L s?1 total discharge, electrical conductivity measurements showed the influx of seawater 6–10 m below sea level and a drawdown of the interface in the piezometers closest to the pumping wells.  相似文献   

9.
The electrical impedance of a sintered forsterite sample containing 1 mol percent SiO2 in excess has been studied as a function of frequency (1–105 Hz) and temperature (400–900°C). The electrical properties are strongly frequency-dependent, requiring both conduction and displacement current for their interpretation. The electrical conductivity is thermally activated with a mean activation energy of 1.15 eV. It is interpreted as being ionic and caused by migration of magnesium ions via a vacancy mechanism. Dielectric data deduced from impedance measurements vary as ωn?1 (0 < n < 1) at constant temperature. The value of n is different below and above a critical frequency ωc, which is thermally activated and interpreted as the jump frequency of the migrating species.  相似文献   

10.
The electrical conductivity of Tibetan eclogite was investigated at pressures of 1.5–3.5 GPa and temperatures of 500–803 K using impedance spectroscopy within a frequency range of 10-1–106 Hz. The electrical conductivity of eclogite increases with increasing temperature(which can be approximated by the Arrhenius equation), and is weakly affected by pressure. At each tested pressure, the electrical conductivity is weakly temperature dependent below ~650 K and more strongly temperature dependent above ~650 K. The calculated activation energies and volumes are 44±1 kJ/mol and-0.6±0.1 cm3/mol for low temperatures and 97±3 kJ/mol and-1.2±0.2 cm3/mol for high temperatures, respectively. When applied to the depth range of 45–100 km in Tibet, the laboratory data give conductivities on the order of 10-1.5–10-4.5 S/m, within the range of geophysical conductivity profiles.  相似文献   

11.
Frequency dependent electrical properties of minerals and partial-melts   总被引：4，自引：0，他引：4  
The resistance to current flow of minerals and partial-melts is a frequency dependent electrical property. Measurements of the frequency dependent electrical impedance of single crystal olivine, polycrystalline olivine, dunites, metapelites, and partial-melts, between 10–4 and 105 Hz, when plotted in the complex impedance plane, reveal arcs that correspond to different conduction mechanisms in the material being studied. In polycrystalline materials, two impedance arcs related to material properties (as opposed to electrode properties or electrode-sample interactions) are observed. Each impedance arc is activated over a distinct range of frequency, that is, the mechanisms occur in series. Based on experiments comparing single and polycrystalline impedance spectra, experiments on samples with different electrode configurations, and on samples of varying dimension, the mechanisms responsible for these impedance arcs are interpreted as grain interior conduction ( gi ), grain boundary conduction (in polycrystalline materials; gb ), and sample-electrode interface effects, from highest to lowest frequency, respectively. Impedance spectra of natural dunitic rocks reveal analogous behavior, that is, gb and gi add in series. The grain boundaries do not enhance the conductivity of any of the materials studied (a direct result of the observed series electrical behavior) and, under certain conditions, limit the total conductivity of the grain interior-grain boundary system. By examining the frequency dependence of the electrical properties of partial-melts, it is possible to gain information about microstructure and the distribution of the melt phase and to determine the conditions under which the presence of melt enhances the total conductivity. Impedance spectra of olivine-basalt partial-melts indicate that at least two conduction mechanisms occur in series over the frequency range 10–4-105 Hz, similar to the observed electrical response of melt-absent polycrystalline materials. In a sample containing isolated melt pockets the intermediate frequency grain boundary impedance arc is modified by the presence of melt indicating series conduction behavior. In a sample with an interconnected melt phase the high frequency grain interior impedance arc is modified by the melt phase, indicating the initiation of parallel conduction behavior. Because field EM response versus frequency curves are used to derive conductivity versus depth profiles, it is important to perform laboratory experiments to understand the frequency-dependent electrical behavior of Earth materials. Activation energies determined from studies that measure conductivity at a single frequency may be erroneous because of the shift of the dominant conduction mechanism with frequency as temperature is varied.  相似文献   

12.
Freshly cored samples from a microprofile (7011–7013m in depth) of the German Continental Deep Drilling Project (KTB) were taken to measure the complex electrical conductivity (1 kHz up to 1 MHz), porosity, BET-surface, permeability and density. The porosity ranged about 1 vol%, while the permeability k varied from 16.05 µD to > 0.01 µD for in-situ pressure conditions. The permeability decreased about 2 orders in magnitude up to pressures of 200 MPa. Conductivity was measured in the same pressure range on 1 M NaCl saturated samples. Thin sections and SEM analysis revealed an enrichment of carbon and ilmenite (about 1 vol%) on inner cleavage cracks of mica, thus causing an unusual high (ranging from 4.2 × 10-3 S/m to 67 × 10-3 S/m) being orders of magnitude higher than normally measured on such types of rocks (about 300 × 10-6 S/m). An inverse pressure dependence of was detected on some of the samples. Electronic conduction was confirmed by least-squares-fits of model data to the frequency dispersion of the conductivity and by measuring the time dependence of the volume conductivity and its frequency dispersion. Thus the dominating role of the reconnected network of carbon and ilmenite on the enhanced volume conductivity was proved. An increase of the conductivity due to hydrofracturing by high pore fluid pressures plays a less important role.  相似文献   

13.
Pore dilation, the compaction of humic acids on peat fibres due to the process of flocculation, causes the hydraulic conductivity of peat to increase with increasing pore water electrical conductivity. This is a reversible process and a reduction in the pore water conductivity produces a decrease in the hydraulic conductivity due to the constriction of pores. We verify how this dilation and constriction of pores, resulting from the application of artificial pore water (primarily deionized water), affects laboratory measurements of the hydraulic conductivity of peat. Repeat measurements of the hydraulic conductivity were performed on samples of Sphagnum peat. It is shown that the application of deionized water during constant head permeameter tests causes a significant decrease in the hydraulic conductivity. Between tests, the hydraulic conductivity of the peat continues to decline without an associate decrease in the pore water electrical conductivity because of a lagged pore constriction effect. We suggest that the use of artificially high or low pore water electrical conductivities, during laboratory hydraulic conductivity measurements, is likely to lead to significant errors. Experimental protocols must, therefore, be revised to take better account of the pore water chemistry. The ionic concentrations of the natural pore fluid should be replicated during hydraulic conductivity tests, either by using pore fluid extracted from the study site or by artificially replicating the major ionic composition of the natural pore fluid. In addition, prior to the hydraulic conductivity measurements, peat samples should be flushed with this solution until the hydraulic conductivity stabilizes and the samples subsequently allowed to equilibrate. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

14.
Field determined hydraulic and chemical transport properties can be useful for the protection of groundwater resources from land-applied chemicals. Most field methods to determine flow and transport parameters are either time or energy consuming and/or they provide a single measurement for a given time period. In this study, we present a dripper-TDR field method that allows measurement of hydraulic conductivity and chemical transport parameters at multiple field locations within a short time period. Specifically, the dripper-TDR determines saturated hydraulic conductivity (Ks), macroscopic capillary length (λc), immobile water fraction (θim/θ), mass exchange coefficient (α) and dispersion coefficient (Dm). Multiple dripper lines were positioned over five crop rows in a field. Background and step solutions were applied through drippers to determine surface hydraulic conductivity parameters at 44 locations and surface transport properties at 38 locations. The hydraulic conductivity parameters (Ks, λc) were determined by application of three discharge rates from the drippers and measurements of the resultant steady-state flux densities at the soil surface beneath each dripper. Time domain reflectometry (TDR) was used to measure the bulk electrical conductivity of the soil during steady infiltration of a salt solution. Breakthrough curves (BTCs) for all sites were determined from the TDR measurements. The Ks and λc values were found to be lognormally distributed with average values of 31.4 cm h−1 and 6.0 cm, respectively. BTC analysis produced chemical properties, θim/θ, α, and Dm with average values of 0.23, 0.0036 h−1, and 1220 cm2 h−1, respectively. The estimated values of the flow and transport parameters were found to be within the ranges of values reported by previous studies conducted at nearby field locations. The dripper TDR method is a rapid and useful technique for in situ measurements of hydraulic conductivity and solute transport properties. The measurements reported in this study give clear evidence to the occurrence of non-equilibrium water and chemical movement in surface soil. The method allows for quantification of non-equilibrium model parameters and preferential flow. Quantifying the parameters is a necessary step toward determining the influences of surface properties on infiltration, runoff, and vadose zone transport.  相似文献   

15.
A summary of experiments and analyses concerning electromagnetic induction in the Moon and other extraterrestrial bodies is presented. Magnetic step-transient measurements made on the lunar dark side show the eddy current response to be the dominant induction mode of the Moon. Analysis of the poloidal field decay of the eddy currents has yielded a range of monotonic conductivity profiles for the lunar interior: the conductivity rises from 3·10?4 mho/m at a depth of 170 km to 10?2 mho/m at 1000 km depth. The static magnetization field induction has been measured and the whole-Moon relative magnetic permeability has been calculated to be μμ0 = 1.01 ± 0.06. The remanent magnetic fields, measured at Apollo landing sites, range from 3 to 327 γ. Simultaneous magnetometer and solar wind spectrometer measurements show that the 38-γ remanent field at the Apollo 12 site is compressed to 54 γ by a solar wind pressure increase of 7·10?8 dyn/cm2. The solar wind confines the induced lunar poloidal field; the field is compressed to the surface on the lunar subsolar side and extends out into a cylindrical cavity on the lunar antisolar side. This solar wind confinement is modeled in the laboratory by a magnetic dipole enclosed in a superconducting lead cylinder; results show that the induced poloidal field geometry is modified in a manner similar to that measured on the Moon. Induction concepts developed for the Moon are extended to estimate the electromagnetic response of other bodies in the solar system.  相似文献   

16.
This paper is devoted to study the effect of saturation, with distilled water, on AC electrical conductivity and dielectric constant of a fully and partially saturated hematitic sandstone sample (Aswan area, Egypt). The saturation of the sample was changed from full saturation to partial saturation by air drying. Complex resistivity measurements at room temperature (∼16° C) were performed in the frequency range from 10 Hz to 100 kHz. We used non-polarizing Cu/CuSO4 gel electrodes. Experimental electrical spectra indicate, generally, that the electrical conductivity and dielectric constant vary strongly with water saturation and frequency. The low-frequency electrical conductivity and dielectric constant are supposed to be mainly controlled by surface conduction and polarization of the electrical double layer. Power law behaviours with frequency were noticed. The change in electrical conductivity and dielectric constant with increasing water content is fast at low saturations and slow at high saturations. The behaviour of the electrical conductivity and dielectric constant, with increasing water content, was argued to be the orientational polarization of bound water for very low saturations, displacement of the excess surface charges for relatively low saturations and free exchange of excess ions in double layer with the bulk electrolyte and generation of transient diffusional potentials, which lag behind the applied field for high saturations in addition to membrane polarization on clay and at inter-grain and grain surface water throats having selective charge transport properties. Also, from the data a semi-percolation behaviour was found that has a peak of dielectric constant at a certain concentration and an abrupt change in conductivity at another saturation.  相似文献   

17.
Abstract

An investigation on the groundwater potentials of the Egbe-Mopa area in central Nigeria, underlain by the Basement Complex, is presented. The investigation involved mapping of the subsurface by use of vertical electrical soundings; measurement of depth to groundwater; and evaluation of hydraulic conductivity, transmissivity and yield by means of pumping test interpretation. The results indicate subsurface units that range from three to five resistivity layers; depth to groundwater of 0–10 m; overburden thickness of 3–16 m; hydraulic conductivity of 6.2?×?10?6 to 3.4?×?10?4 m/s; transmissivity of 4.3?×?10?7 to 2?×?10?3 m2/s; and groundwater yield of 0.2–2.5 L/s. The hydraulic head assessments revealed a general northward groundwater flow direction. The study identified three aquifer potential types, of high, medium and low productivity, respectively. Based on the longitudinal conductance of the overburden units, four distinct Aquifer Protective Capacity zones were delineated, namely, poor, weak, moderate and good.

Citation Okogbue, C.O. and Omonona, O.V., 2013. Groundwater potential of Egbe-Mopa basement area, central Nigeria. Hydrological Sciences Journal, 58 (4), 826–840.  相似文献   

18.
The soil in the Loess Plateau has special permeability characteristics due to the alternating distribution of loess and paleosol layers. Using an analysis of the physical properties, microstructure and thermogravimetric analysis of loess and paleosol, this paper examines strata seepage mechanisms in the loess tableland area and considers the applicability of a hydraulic conductivity empirical formula. The analysis shows that hydraulic conductivity attenuation with depth can be represented by a negative exponential model, while hydraulic conductivity values are not normally distributed. The best-fitting models of hydraulic conductivity in the horizontal (KH) and vertical (KV) directions are Gaussian models, and both have strong spatial correlations. This study of the difference in permeability between loess and paleosol found that the depositional environment was the dominant causal factor, making the average hydraulic conductivity of most loess layers greater than that of the underlying paleosol layers. Different microstructures between loess and paleosol also confirmed the microscopic explanation in permeability anisotropy and their permeability difference. Thermogravimetric analysis determined temperature ranges for different types of water lost by heat, and then calculated ratios of bound water mass to liquid limit, with an average of 0.768. A modified formula suitable for loess was obtained by integrating the consistency index method and effective porosity ratio model into the hydraulic conductivity empirical formula. Compared with the results of laboratory tests and uncorrected formulas, the modified formula provides a good estimate of strata hydraulic conductivity. Accurate understandings of seepage mechanisms and permeability differences in the loess area are important, promoting ecological restoration and providing scientific guidance for the sustainable development of the Loess Plateau.  相似文献   

19.
Abstract

A borehole is developed in a shallow multi-layered aquifer and used to derive the porosity, specific storage and hydraulic conductivity of the aquitard. Local values of hydrodynamical parameters are estimated from petrophysical analysis of core samples, and the empirical relationship between porosity and permeability. Vertical diffusivity is determined from the response of the aquitard to a loading cyclic signal using pressure records at different depths. Hydraulic conductivities deduced from the petrophysical analysis ranged from 10?8 to 10?10 m s?1 and are comparable with those of facies of marine/lacustrine clay observed in samples. The permeability values calculated based on diffusivity are within the range 10?9 to 10?11 m s?1 with a quasi-systematic bias of one order of magnitude. These values are average for a larger part of the aquitard and correspond to an integrated value. The methodology retained for the aquitard characterization is discussed with emphasis on the implications for the management of a complex aquifer system.

Citation Larroque, F., Cabaret, O., Atteia, O., Dupuy, A., and Franceschi, M., 2013. Vertical heterogeneities of hydraulic aquitard parameters: preliminary results from laboratory and in situ monitoring. Hydrological Sciences Journal, 58 (4), 912–929.  相似文献   

20.
Quiet daily magnetic variations recorded by magnetometer arrays in Australia are analysed to obtain electromagnetic response parameters for two parts of the Australian continent remote from electrical conductivity anomalies. The parameters are based on measurements of vertical-field and horizontal-field spatial gradient, and three different methods are followed in their computation. The response parameters are checked for consistency with a compilation of globally-determined Earth apparent resistivities, and are then interpreted for one-dimensional conductivity structure in the two different parts of the continent. There is evidence that the rise in electrical conductivity from 10?1 S m?1 to 100 S m?1 which occurs at a depth of order 500 km beneath central Australia may occur at a substantially shallower depth of order 230 km beneath southeast Australia.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号