共查询到20条相似文献，搜索用时 31 毫秒
1.
On 19 March 2013, a tremor shook the surface of Polkowice town where the Rudna Mine is located. This event, of ML = 4.2, was the third most powerful seismic event recorded in the Legnica G?ogów Copper District (LGCD). Inhabitants of the area reported that the felt tremor was bigger and lasted longer than any other ones felt in the last couple of years. Analysis of spectral parameters of the records from in-mine seismic system and surface LUMINEOS network along with broadband station KSP record were carried out. The location of the event was close to the Rudna G?ówna Fault zone; the nodal planes orientations determined with two different approaches were almost parallel to the strike of the fault. The mechanism solutions were also obtained as Full Moment Tensor from P-wave amplitude pulses of underground records and waveform inversion of surface network seismograms. The results from the seismic analysis along with macroseismic survey and observed effects from the destroyed part of the mining panel indicate that the mechanism of the event was complex rupture initiated as thrust faulting on an inactive tectonic normal fault zone. The results confirm that the fault zones are the areas of higher risk, even in case of carefully taken mining operations. 相似文献
2.
On May 7, 1986, the residents of Tuscaloosa, Alabama, felt a seismic event of local magnitude 3.6 that occurred at the same time as a rock burst and roof collapse in an active longwall coal mine. Visual inspection of the seismograms reveals a deficiency in energy at frequencies above 20 Hz compared to tectonic earthquakes or surface blasts. The predominance of energy below 5 Hz may explain reports of body wave magnitudes (m
b
) greater than 4.2. Also, 1.0 Hz surface waves were more strongly excited than body waves and may explain local felt effects more typically associated with greater epicentral distances. All recorded first motions were dilatational. The concentration of stations in the northern hemisphere allows reverse motion on an east-trending near-vertical plane or strike-slip motion on northwest or southeast trending planes. The reverse focal mechanism is preferred, because the area of roof collapse and the area of active longwall mining are located between two east-striking loose vertical fracture zones. The characteristics of the seismic event suggest that it might have been sudden shear failure resulting from accumulated strain energy in overlying strata behind an active longwall. Although an alternate interpretation of the focal mechanism as an implosion or shear failure in the strata above previously mined out areas is also allowed by the first motion data, this alternate intepretation is not supported by geological data. 相似文献
3.
矿震震动波速度层析成像,作为一种新的地球物理方法在冲击矿压危险评估领域具有广阔的应用前景,但截至目前,采用该技术评估冲击危险的现场应用研究还比较少,尤其是与传统监测手段的对比验证研究,还未见有相关文献报道.本文将层析成像技术和微震实时监测相结合,对河南义马跃进煤矿25110工作面回采过程中的P波速度进行了反演,并对比分析了该技术与传统监测手段之间的对应关系.研究结果表明,强矿震主要发生在高波速区或高波速变化梯度区;波速与数值模拟结果、钻屑量、钻孔应力值以及电磁辐射值之间存在正相关关系,且对应一致性较好,进而验证了矿震震动波速度层析成像技术评估冲击危险的可行性,同时也为进一步研究波速与应力或冲击危险的直接及定量关系提供参考. 相似文献
4.
为了研究煤矿冲击地压与岩层在三维空间破裂之间的关系，进而探索依据岩层破裂规律预测和预报冲击地压的可能性，文中采用自行研制的防爆型微地震定位监测（MS）系统，基于定位原理，监测了山东华丰煤矿冲击地压煤层（四层煤）及其解放层（六层煤）开采过程中的岩层破裂过程和二次应力场分布变化的过程，得到了如下结论：冲击地压的发生与岩层破裂密切相关，四层煤下顺槽处于六层煤顶板破裂区的外边缘时，正处于高应力区内，在此处掘进容易引发冲击地压，必须将六层煤下顺槽位置向实体煤侧移动20 m以上，或将四层煤下顺槽位置内移20 m以上，才能消除四层煤的冲击地压；六层煤和四层煤开采时，工作面前方断层活化的距离分别为250 m和350 m左右，根据这一距离，及时对断层带进行卸压处理，可以消除由断层带引发的冲击地压；监测显示了工作面周围岩层的三维破裂形态和范围，为矿井确定防水煤柱的高度提供了可靠的依据；监测证明了厚层砾岩的破裂、断层活化、采场附近关键层的破裂是引起冲击地压的主要原因，证明了所研制的硬件和定位软件具有较高的精度和实用性，可以在煤矿和边坡、隧道等领域应用. 相似文献
5.
Ralf Fritschen 《Pure and Applied Geophysics》2010,167(1-2):77-89
Coal mining in the Saar mine, Germany, is accompanied by mining-induced seismic events. Strong events occur only in certain areas of the mine, other areas exhibit almost no seismicity. Shear events occur simultaneously to non-shear events. The shear events occur in different depths but their epicenters do concentrate in bands. The strike of the bands coincides with the strike of larger regional faults in the area. The seismic events of the Saar mine show some characteristics which distinguish them from seismic events observed in other German coalfields. The Gutenberg–Richter relation, for example, does not hold for these events. Furthermore, radiated seismic energy and extracted coal volume are not correlated. In the Primsmulde field a strong seismic event was observed even before mining in that region started. The event was triggered just by driving roadways into the field. The shear events cannot be explained by the mining process alone. They are presumably induced in certain regions (bands) under tectonic load by an interaction of mining-induced and tectonic stresses. In February 2008, extraction in the Primsmulde field induced a seismic event of magnitude 4, which led to surface vibrations reaching 93 mm/s. After this event, the Primsmulde field had to be abandoned. Future extraction of the Saar mine will be restricted to some small areas not intersected by the event bands found in the Dilsburg Ost and Primsmulde fields. The Saar mine will close in 2011. 相似文献
6.
R. P. Young S. Talebi D. A. Hutchins T. I. Urbancic 《Pure and Applied Geophysics》1989,129(3-4):455-474
Rockbursts and mining-induced seismic events have serious socio-economic consequences for the Canadian mining industry, as their mines are extended to greater depths. Automatic multichannel monitoring systems (Electro-Lab MP250s) are routinely, used to detect the arrival times of seismic waves radiated by mining-induced events and sensed on an array of single component transducers installed throughout a mine. These arrival times are then used to locate the events and produce maps of areas of high activity for use in mine planning and design. This approach has limitations in that, it does not allow a detailed analysis of source mechanisms, which could be extracted if whole waveform signals are recorded and analyzed.A major research project, sponsored by the Natural Sciences and Engineering Research Council of Canada (NSERC) with the collaboration of the Canadian mining industry, is aimed at enhancing existing mine seismic monitoring technology in Canada, in order to carry out more advanced processing of data to obtain fundamental scientific information on mining-induced seismic events This paper describes preliminary results from seismic monitoring experiments carried out in a hard rock nickel mine in Sudbury, Canada. Existing seismic monitoring instrumentation was enhanced with a low cost microcomputer-based whole waveform seismic acquisition system. Some of the signals recorded during this experiment indicate anisotropic wave propagation through the mine rock masses, as observed by the splitting of shear waves and the relative arrival of two shear waves polarized in directions which may be related to the structural fabric and/or state of stress in the rock mass. Analysis of compressional wave first motion shows the predominance of shear events, as indicated by focal mechanism studies and is confirmed by spectral analysis of the waveforms. The source parameters were estimated fro typical low magnitude localized microseismic events during the initial monitoring experiments. The seismic moment of these events varied between 106 N.m and 2.108 N.m. with a circular source radius of between 1 m and 2 m with an estimated stress drop of the order of 1 MPa. 相似文献
7.
基于贝叶斯原理，建立了地震事件识别判据的综合方法（简称贝叶斯方法）， 并针对中亚地区大量地震事件，采用该方法综合了不同台站和不同频带的P/S震相幅值比判据. 该方法的主要优点是能够给出事件属于爆炸的概率，而且充分考虑了判据之间的相关性. 理论计算和模拟数据分析结果表明， 贝叶斯方法是最优的综合方法， 其识别效果比任何单个判据好，也好于普通线性组合方法的识别效果. 针对中亚地区大量地震事件综合不同台站和不同频带的P/S震相幅值比判据的结果也表明，贝叶斯方法的误识率低于单个判据和线性组合方法的误识率. 相似文献
8.
A multivariate discrimination technique was established based on the Bayesian theory. Using this technique, P/S ratios of different types (e.g., Pn/Sn, Pn/Lg, Pg/Sn or Pg/Lg) measured within different frequency bands and from different stations were combined together to discriminate seismic events in Central Asia. Major advantages of the Bayesian approach are that the probability to be an explosion for any unknown event can be directly calculated given the measurements of a group of discriminants, and at the same time correlations among these discriminants can be fully taken into account. It was proved theoretically that the Bayesian technique would be optimal and its discriminating performance would be better than that of any individual discriminant as well as better than that yielded by the linear combination approach ignoring correlations among discriminants. This conclusion was also validated in this paper by applying the Bayesian approach to the above-mentioned observed data. 相似文献
9.
《Journal of Applied Geophysics》2007,61(1):1-15
The presence of an excavation disturbed zone (EDZ) around an excavation boundary can significantly affect the overall performance of the excavation and the general safety of men and equipment. Hence, it has been an important subject of research in various rock excavation projects. The EDZ is generally defined as the rock zone beyond the excavation boundary where the physical, mechanical and hydraulic properties of the rock have been significantly affected due to the excavation and redistribution of stresses. For LKAB's Kiirunavaara underground iron ore mine in Sweden, the understanding of the EDZ is essential for optimal design of rock support. With this main objective an EDZ investigation was conducted at the mine using seismic measurement techniques. Cross-hole seismics and spectral analyses of surfaces waves (SASW) were the main techniques used. Borehole Image Processing Systems (BIPS) complemented the seismic measurements. The results show that an EDZ with a thickness of 0.5–1. 0 m existed behind the boundaries of the mining drifts being investigated. The magnitude of the Young's modulus of this zone was 50% to 90% of that of the undisturbed rock. 相似文献
10.
Seismic records produced by different seismic sources vary. In this study, we compared the waveform records and time-frequency characteristics of tectonic earthquakes, artificial explosions, and mine collapses in China’s Capital Region. The results show that tectonic earthquakes are characterized by stronger S-wave energy than P-wave energy, obvious high-frequency components, and wide frequency bands of P and S waves. Artificial explosions are characterized by greater P-wave amplitude than S-wave amplitude and near-station surface wave development. Mine collapses are characterized by lower overall frequency, more obvious surface waves, and longer duration. We extracted quantitative discriminants based on the analysis of different event records, with 31 feature values in 7 categories (P/S maximum amplitude ratio, high/low frequency energy ratio, P/S spectral ratio, corner frequency, duration, the second-order moment of spectrum, and energy strongest point). A comparison of the ability of these feature values to recognize distinct events showed that the 6–17 Hz P/S spectral ratio was able to completely distinguish artificial explosions from the other two types of events. The S-wave corner frequency performed relatively well in identifying all three types of events, with an accuracy of over 90%. Additionally, a support vector machine was used to comprehensively distinguish multiple features, with an accuracy for all three types of events reaching up to 100%. 相似文献
11.
—?The potential for large excavation-induced seismic events may be recognised, even if the timing of an event may be inherently unpredictable. In this case, modelling the wave propagation from a potential event could allow the dynamic motions around an excavation to be projected, and for areas of danger to be anticipated. However, the above and other potential applications require accurate models of wave interaction with the openings, as well as with the fractured rock which surrounds such excavations. This paper considers real recorded waveforms and how well these waveforms are modelled by explicit mechanical models of the source, the medium and the excavation. Models of experiments at three different scales of the problem are presented: small and large amplitude waveforms recorded around a deep-level mining tunnel in a synthetic rockburst experiment; waveforms from laboratory experiments of waves through plates of steel representing fractures; waveforms from active pulses in an acoustic emission experiment in a small volume of fractured rock at the surface of an underground excavation. The results show that elastic wave propagation around an excavation was a first approximation for small amplitude waves, but was less successful for modelling large amplitude waves and more fractured rock. Fractures in the models were represented explicitly with displacement discontinuities. Waveforms through known fracture geometries were particularly well-reproduced, and indicate the importance of fracture stiffness, the in situ stress state, and stress-dependence of the fractures in such models. Overall, the models are sufficiently successful at representing recorded behaviour, to be encouraging for the goal of representing accurate wave motions around excavations. 相似文献
12.
On May 2, 1993 more than 200 seismic events from an underground mine in Tyrol/Austria were recorded with short-period seismometers of a local seismic network which was introduced in the late 1980s to monitor the tectonic seismicity in Tyrol in greater detail. The cause of this series of mining-associated events has become the subject of intensive investigations — as it was associated with a subsidence affecting an area of 10.000 m2. Underground observations revealed a number of discontinuities along which the rock mass was able to move. Seismic recordings of the close-by seismic stations revealed two types of mechanisms: One mechanism seems to be associated with pure block-sliding along several discontinuities, while other signals indicate additional collapse. The consideration and combination of several seismological principles made possible the construction of a model of the mine collapse. 相似文献
13.
Seismic Moment Tensor Resolution on a Local Scale: Simulated Rockburst and Mine-induced Seismic Events in the Kopanang Gold Mine, South Africa 总被引：2，自引：0，他引：2
Seismic records contain information about the effect of the source as well as the effect of wave propagation through the rock
mass. The effect of wave propagation is usually not well known as only simplified models of geological structures are available.
Therefore, the information about the source retrieved by inverting seismograms may include errors due to incomplete knowledge
of the rock mass along the propagation path, which in turn cause a distortion in the calculated moment tensor (MT). The distortion
of the MT on a local scale was observed by inverting records of a simulated rockburst conducted at the Kopanang gold mine
in South Africa. A dominant isotropic component of the explosive characteristics was found from the inversion. The deviatoric
components retrieved from the blast are spurious. A test of their stability indicated that they are not significant, assuming
an uncertainty above 5% for velocities and 10% for attenuation within the homogeneous model available for the mine. Thus,
the retrieval of the MT from records of local networks in mines using a homogeneous model of the rock mass seems to be feasible.
However, the homogeneous model of the rock mass can only be applied to close stations, within a few kilometers of the source.
The seismic records from distant stations were too complex to be modelled by a homogeneous rock mass. Records of six mine-induced
seismic events recorded at the Kopanang gold mine were also inverted. A vertical linear dipole along the pressure (P) axis
was found for three of the events, suggesting a pillar burst. The mechanism of two events contains an isotropic implosion
together with a nearly vertical dip-slip, and seems to indicate a combination of a cavity collapse with a down dip-slip along
a nearly vertical fault. One event corresponds to a dipole along the tensional (T) axis. However, it is vertical, thus its
association with tensile faulting of the hangingwall is uncertain. 相似文献
14.
本文在考虑动态力源扰动的情况下,对岩石损伤对地震波辐射的影响及其震源表示进行了理论推导,证明了当有动态力源存在时,Ben-Zion和Ampuero于2009年给出的结果只是岩石非弹性响应对震源及相应地震波场的贡献,而非其全部.在此基础上,应用相关结果对岩石损伤破坏对地下核爆炸震源成分的影响进行了分析,给出了地下核爆炸情况下补偿线性偶极子源和构造应力释放与岩石损伤破坏之间的关系.结果表明,地下核爆炸补偿线性偶极子源主要来自于地表反射拉伸波和空腔回弹冲击波等造成的爆心上方锥形区域中的岩石破坏,而构造应力释放则主要来自于整个岩石破坏区内的构造应力松弛. 相似文献
15.
Seismic events with non-shear component: II. Rock bursts with implosive source component 总被引：2，自引：0，他引：2
The rock burst mechanism of an implosive character is introduced and discussed; it is based on the idea that the compressional component of the stress field around the loaded stress concentrator can participate in the rock burst event. For easier classification of the rock burst from this viewpoint, a set of P-wave radiation patterns of the rock burst with a varying portion of the implosive component and varying propagation velocity of the displacements is presented and discussed. To support the credibility of the rock burst mechanism of an implosive character the seismic signals of the rock bursts from the mid-Bohemian coal district with negative signs of the P-wave first onsets are presented. 相似文献
16.
Hard coal mining in the area of the Bytom Syncline (Upper Silesia Coal Basin, Poland) has been associated with the occurrence of high-energy seismic events (up to 109 J; local magnitude up to 4.0), which have been recorded by the local mining seismological network and regional seismological network. It has been noticed that the strongest seismic events occur when the mine longwall alignments coincide with the syncline axis. Data recorded by the improved local seismic network in the Bobrek Mine allow the estimation of the depths of the events’ hypocentres during excavation of longwall panel 3 as it approached the syncline axis. The recorded data were also used to estimate the location of the rupture surface and stress distribution in the seismic focus region. It was concluded that tectonic stresses, particularly horizontal stress components, are essential in the distribution of seismic tremors resulting from reverse faulting. The stresses induced by mining activity are only triggering tectonic deformations. The hypocentres of the strongest seismic events during mining of longwall panel 3/503 were located 300–800 m deeper than the level of coal seam 503. 相似文献
17.
利用河南新密超化镇某矿区布设的密集临时地震台网观测资料,通过微震震源精确定位手段,实现强干扰背景下该地区某煤矿地下开采面的定位追踪试验研究。微震定位后,爆破点位置的水平精度为±70m,垂直精度为±500m。试验研究结果表明,利用高密度数字地震台网资料,可较为准确地监测矿山地下开采面的动态变化,从而实现对矿产资源越界开采和小矿非法开采的有效制约和监督。同时,本次试验结果显示地震台网的监测控制范围受爆炸源能量、地下开采面的深度、监测区背景噪声、监测仪器的灵敏度和抗干扰能力等因素影响,试验结果可对今后矿区地震监测台网的合理布设提供有效指导。 相似文献
18.
针对波速分层的区域岩体,在异向波速模型的基础上,对垂向上的应力波按岩体波速值大小作分段区别,推导震源应力波走时关系式,建立分层速度定位目标函数,基于此提出一种由参数准备、层速度反演、微震定位三个模块组成的分层速度定位模型SV,并采用遗传算法进行优化求解.然后,对分层速度定位模型在已构建微震监测系统的白鹤滩水电站左岸岩质边坡进行验证.微震事件重定位结果表明,分层速度定位模型定位微震事件的最大、最小和平均偏离层内错动带程度指标较单一速度模型分别降低了57.17%、36.51%和57.35%,证明了定位模型在波速分层的区域岩体微震定位应用中比单一速度定位模型更加合理可靠. 相似文献
19.
—?The aim of our study consists of analyzing potentially non-double-couple seismic events recorded at regional distances. In order to define the nature of the seismic source, a moment tensor inversion is carried out as this method is general enough not to initially constrain the source mechanism. In this paper we present an application to a seismic event induced by a mine collapse which occurred near the town of Halle in Germany. Because of its induced nature, many parameters such as the location and geometry of this seismic source are known. This information allows us to test the influence of inadequate propagation modeling on the moment tensor obtained from the inversion. Green's functions have been computed with the reflectivity method in a flat layered medium, using the European model EurID (Du et? al., 1998; Dufumier et al., 1997). From the inversion of P-wave seismograms recorded by the German Regional Seismic Network will, we obtained a source time function which can be decomposed into two subevents. The first one has a large isotropic part and a deviatoric mechanism with near vertical nodal planes. No volume change is observed for the second subevent, but a deviatoric component opposite of the first one. The addition of S-waves does not change the results of the inversion which are stable. Surface waves were not used because of their poor dispersion curves. Based on the moment tensor obtained from these inversions, the physical process at the source is compatible with a large cavity collapse. 相似文献