共查询到18条相似文献，搜索用时 250 毫秒
1.
采用大型通用有限元程序,对低硬度大直径橡胶隔震支座在竖向荷载作用下的基本性能进行了精细有限元分析。分析了在竖向荷载作用下支座上下封板、内部钢板的各种应力分布,以及支座顶部是否施加竖向同位移约束、支座孔径比、橡胶材料G值、内部单层橡胶厚度与内部单层钢板厚度之比对支座内钢板受力的影响。结果表明,内部钢板最大Mises应力、最大径向水平正应力约为支座竖向压力的4倍、2.5倍;支座顶部是否施加竖向同位移约束对支座用钢板内力影响较大,特别是支座上封板;橡胶G值的变化对内部钢板受力基本没影响;支座孔径比对靠近孔边缘部分内部钢板应力不均匀性分布影响较大;内部单层橡胶厚度与内部单层钢板厚度的比值对内部钢板的Mises应力、径向正应力、环向正应力影响较大,但对其竖向正应力基本没影响。 相似文献
2.
夹层橡胶隔震支座全刚性性能、回转刚性及高压缩应力性能试验研究 总被引：6，自引：1，他引：5
本文详细地研究了夹层橡胶隔震支座的全刚性性能,同时还研究了夹层 橡胶隔震支座的回刚性,并给出了竖向压力及剪切变形对隔震支座回转刚性的影响结果,文末给出了隔震支座在高压缩应力作用下的基本力学性能,研究结果显示在竖向压缩压力达到30MPa时,隔震支座仍可具有良好的力学性能。 相似文献
3.
低硬度橡胶隔震支座基本力学性能及恢复力特性 总被引：4，自引：2，他引：4
本研究对低硬度橡胶隔震支座的材料性能（主要包括力学性能）进行了系统的试验开发及理论研究。研究用低硬度橡胶隔震支座包括天然橡胶隔震支座及铅芯橡胶隔震支座两大类18种规格总计近30个大直径隔震支座。研究内容涉及橡胶隔震支座竖向刚度、水平刚度及阻尼等基本力学性能；压缩界限，屈曲及极限剪切变形等界限性能；温度、压力、剪切变形、老化和徐变等相关性及长期特性；同时还对橡胶材料其他性能进行了系统的试验研究。本文主要介绍低硬度天然橡胶隔震支座及铅芯橡胶隔震支座的基本力学性能，如竖向、水平刚度和恢复力等特性。 相似文献
4.
中国铅芯夹层橡胶隔震支座各种相关性能及长期性能研究 总被引：5，自引：1，他引：5
本文详细地研究了各种相关因素对中国铅芯橡胶隔震支座力学性能的 影响，同时还研究了中国铅芯夹层橡胶隔震支座的长期性能。研究包括竖向压力、频率、剪切变形循环次数、温度对隔震支座刚度及阻尼等力学性能的影响；隔震支座的耐久性能诸如老化及徐变对隔震器刚度、阻尼特性及极限变形能力的影响。研究还包括水平剪切（200次）及竖向低周疲劳（10万次）试验对隔震器力学性能的影响。 相似文献
5.
方形多铅芯橡胶支座力学性能研究 总被引：7，自引：0，他引：7
本文通过对方形多铅芯橡胶支座竖向压缩性能试验,水平剪切性能试验以及其等效刚度、屈服强度、屈服后刚度、等效阻尼比等水平特征参数与水平剪切应变和竖向压应力的关系,特别是对其在不同方向上压缩剪切变形状态下的性能试验,分析了这种隔震支座各种水平特征参数在不同方向上变化的相关规律。得出在这种类型橡胶隔震支座在双向水平荷载同时作用下,竖向性能和水平性能较为稳定,是较为理想的桥梁结构的减隔震装置。 相似文献
6.
《华南地震》2017,(4)
通过研究三维隔震支座与二维隔震支座力学性能的相关关系,对传统的蝶形弹簧改进,并将改进后的新型蝶形弹簧通过对合叠合的方式组成蝶形弹簧竖向隔震支座,与普通橡胶支座通过串联的方式组合成一个新型的三维隔震支座。对二维天然隔震橡胶支座(LNR)、碟形弹簧竖向隔震支座、三维隔震支座分别进行了水平方向和竖向力学性能试验,分析了独立状态下的二维隔震支座与三维隔震支座相互之间力学性能的关系,并对其规律进行了归纳和总结。试验结果表明:竖向弹簧片支座的竖向刚度随压应力的增加呈线性变化;在低频率情况下频率对其竖向刚度影响不大;三维隔震支座的水平刚度相对于独立状态下的LNR会略有降低;LNR对三维隔震支座的整体竖向刚度的影响不大。 相似文献
7.
8.
9.
10.
厚层铅芯橡胶支座具有同时隔离水平地震动和竖向地震动的三维隔震性能,其竖向刚度是影响厚层橡胶支座竖向隔震性能的关键因素。基于厚层铅芯橡胶支座三维有限元模型,研究铅芯对厚层铅芯橡胶支座竖向刚度的影响,模型分析中考虑铅芯与周边边界的不同约束情况,研究铅芯的边界约束条件对支座竖向刚度的影响,分析结果表明,铅芯单元边界约束考虑法向可分离、切向可滑移且边界接触摩擦系数取0.9时较为符合支座实际情况。研究了铅芯直径对支座竖向刚度的影响,结果表明,铅芯对支座竖向刚度的贡献除铅芯材料自身刚度及其边界约束条件外,尚应考虑铅芯直径的影响。同时进行了支座性能试验,通过有限元分析结果与试验结果的比较,验证有限元分析方法的有效性及铅芯边界约束条件定义的合理性。 相似文献
11.
Because a conventional isolation system with constant isolation frequency is usually a long‐period dynamic system, its seismic response is likely to be amplified in earthquakes with strong long‐period wave components, such as near‐fault ground motions. Seismic isolators with variable mechanical properties may provide a promising solution to alleviate this problem. To this end, in this work sliding isolators with variable curvature (SIVC) were studied experimentally. An SIVC isolator is similar to a friction pendulum system (FPS) isolator, except that its sliding surface has variable curvature rather being spherical. As a result, the SIVC's isolation stiffness that is proportional to the curvature becomes a function of the isolator displacement. By appropriately designing the geometry of the sliding surface, the SIVC is able to possess favorable hysteretic behavior. In order to prove the applicability of the SIVC concept, several prototype SIVC isolators, whose sliding surfaces are defined by a sixth‐order polynomial function, were fabricated and tested in this study. A cyclic element test on the prototype SIVC isolators and a shaking table test on an SIVC isolated steel frame were all conducted. The results of both tests have verified that the prototype SIVC isolators do indeed have the hysteretic property of variable stiffness as prescribed by the derived formulas in this study. Moreover, it is also demonstrated that the proposed SIVC is able to effectively reduce the isolator drift in a near‐fault earthquake with strong long‐period components, as compared with that of an FPS system with the same friction coefficient. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
12.
《地震工程与工程振动(英文版)》2021,(3)
The scrap tire rubber pad(STRP) made by natural or synthetic rubber and high strength reinforcing cords exhibits substantial vertical stiffness and horizontal flexibility, and these properties can be regarded as suitable for seismic isolators for structures. The use of environmentally burdensome scrap tires as STRP isolators might be convenient as an efficient and low-cost solution for the implementation of aseismic design philosophy for low-to-medium rise buildings, especially in developing countries. Finite element analyses of unbonded square and strip-shaped STRP isolators subjected to a combination of axial and lateral loads are conducted to investigate its lateral deformation performance under seismic loading. The rubber of the isolator is modelled with Mooney-Rivlin hyperelastic and Prony viscoelastic materials, including the Mullins material damage effect. The influence of the length-to-width ratio and bearing height on the isolator performance is assessed in terms of the force-displacement relationship, horizontal stiffness, damping, and isolation periods. It is shown that the dependence of stiffness on the length-to-width ratio is significant in the longitudinal direction and minor in the transverse direction. The STRP isolators following the proposed design criteria are shown to satisfy the performance requirement at different levels of seismic demand specified by the ASCE/SEI 7-2010 seismic provisions. 相似文献
13.
The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
14.
Evaluation of simplified methods of analysis for structures with triple friction pendulum isolators 总被引：1，自引：0，他引：1
Michael C. Constantinou 《地震工程与结构动力学》2010,39(1):5-22
Triple friction pendulum isolators, that exhibit behavior with amplitude‐dependent strength and instantaneous stiffness, represent a new development in seismic isolation. The application of simplified methods of analysis for this type of seismically isolated structures requires development of tools of simplified analysis and demonstration of their accuracy. This paper describes these tools and presents validation studies based on a large number of nonlinear response history analysis results. It is shown that simplified methods of analysis systematically provide good and often conservative estimates of isolator displacement demands and good estimates of isolator peak velocities. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
15.
Optimized earthquake response of multi‐storey buildings with seismic isolation at various elevations
The response of multi‐storey structures can be controlled under earthquake actions by installing seismic isolators at various storey levels. By vertically distributing isolation devices at various elevations, the designer is provided with numerous options to appropriately adjust the seismic performance of a building. However, introducing seismic isolators at various storey levels is not a straightforward task, as it may lead to favourable or unfavourable structural behaviour depending on a large number of factors. As a consequence, a rather chaotic decision space of seismic isolation configurations arises, within which a favourable solution needs to be located. The search for favourable isolators' configurations is formulated in this work as a single‐objective optimization task. The aim of the optimization process is to minimize the maximum floor acceleration of the building under consideration, while constraints are specified to control the maximum interstorey drift, the maximum base displacement and the total seismic isolation cost. A genetic algorithm is implemented to perform this optimization task, which selectively introduces seismic isolators at various elevations, in order to identify the optimal configuration for the isolators satisfying the pre‐specified constraints. This way, optimized earthquake response of multi‐storey buildings can be obtained. The effectiveness of the proposed optimization procedure in the design of a seismically isolated structure is demonstrated in a numerical study using time‐history analyses of a typical six‐storey building. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
16.
Mohammed Ismail 《地震工程与结构动力学》2015,44(7):1115-1137
The ability of a recently proposed seismic isolation system, with inherent self‐stopping mechanism, to mitigate or even eliminate seismic pounding of adjacent structures is investigated under severe near‐fault earthquakes. The isolation system is referred to as roll‐in‐cage (RNC) isolator. It is a rolling‐based isolator that provides in one unit the necessary functions of vertical rigid support, horizontal flexibility with enhanced stability, hysteretic energy dissipation, and resistance to minor vibration loads. In addition, the RNC isolator is distinguished by a self‐stopping (buffer) mechanism to limit the bearing displacement under excitations stronger than a design earthquake or at limited seismic gaps, and a linear gravity‐based self‐recentering mechanism to prevent permanent bearing displacement without causing vertical fluctuation of the isolated structure. A previously developed multifeature SAP2000 model of the RNC isolator is improved in this paper to account for the inherent buffer mechanism's damping. Then, the effectiveness of the isolator's buffer mechanism in limiting peak bearing displacements is studied together with its possibly arising negative influence on the isolation efficiency. After that, the study investigates how to alleviate or even eliminate those possibly arising drawbacks, due to the developed RNC isolator's inner pounding as a result of its buffer activation, to achieve efficient seismic isolation with no direct structure‐to‐structure pounding, considering limited seismic gaps with adjacent structures and near‐fault earthquakes. The results show that the RNC isolator could be an efficient solution for aseismic design in near‐fault zones considering limited seismic gaps. Earthquake Engineering and Structural Dynamics. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
17.
18.
Murat Dicleli 《地震工程与结构动力学》2008,37(6):935-954
In this paper, the efficiency of providing elastic‐gap devices (EGDs) to improve the performance of seismic‐isolated bridges (SIBs) in near‐fault (NF) zones is investigated. The device is primarily made of an assembly of circular rubber bearings and steel plates to provide additional elastic stiffness to the SIB upon closure of a gap. The EDG is intended to function at two performance levels under service and maximum considered design level (MCDL) NF earthquakes to reduce isolator displacements while keeping the substructure forces at reasonable levels. A parametric study, involving more than 500 nonlinear time history analyses of realistic and simplified structural models of typical SIBs, is conducted using simulated and actual NF ground motions to investigate the applicability of the proposed solution. It is found that providing EGD is beneficial for reducing the isolator displacements to manageable ranges for SIBs subjected to MCDL NF ground motions regardless of the distance from the fault and characteristics of the isolator. It is also found that providing EGD resulted in an improved performance of the isolators in terms of the reduction of heat generated by the isolators. Further analyses conducted using a realistic structural model of an existing bridge and five NF earthquakes confirmed that EGD may be used to reduce the displacement of the isolators while keeping the substructure base shear forces at reasonable ranges for SIBs located in NF zones. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献