共查询到20条相似文献，搜索用时 15 毫秒
1.
关于结构振型参与系数和振型贡献的分析 总被引：1，自引：0，他引：1
采用振型分解反应谱法求解多自由度弹性体系的地震反应时,为了在满足所需计算精度的前提下减少工作量,需要对振型数量进行合理的选择,而振型数的确定主要取决于结构各阶振型对总体反应的贡献。通过数学推导,对振型贡献及振型数量的选择问题进行了研究。首先,讨论了振型参与系数的性质,在此基础上给出了能够反映结构振型贡献参数的数学表达式,对这些参数的力学含义进行了解释,并给出了相关证明;其次,对有效质量法、振型位移控制法等基于不同振型贡献标准的确定振型数的方法进行了分析比较,指出了其合理性和不足。本文研究对进一步理解结构振型贡献和振型数的选择问题具有一定的理论意义。 相似文献
2.
为研究结构平面规则性的界定方法,首先分析了平面规则结构的振型序列特征并验证了其稳定性。以L型结构为例,通过将规则结构的振型序列特征与L型结构的振型序列特征对比,得到了不同L型结构的平面规则性界定曲线,指出了凸出部分的横向长度与横向总长度之比、凸出部分的纵向长度与纵向总长度之比和结构高度是影响L型结构平面规则与否的重要因素,并建议平面不规则结构位移比限值取1.3。提出了基于振型的结构平面规则性界定方法,即:与平面规则结构的振型序列相比,平面不规则结构的振型序列中不利振型（扭转振型、包含扭转的耦合振型及局部振型等需考虑空间效应的振型）会提前。通过对一实际结构进行计算分析,验证了基于振型的结构平面规则性界定方法的优越性和正确性。 相似文献
3.
基于两阶段稳定图的随机子空间识别结构模态参数 总被引：4，自引：1，他引：3
基于振动的结构健康监测的前提是从振动测试信号中提取结构模态参数。随机子空间方法是近年来发展起来的一种线性系统辨识方法,可以有效地从环境激励的结构响应信号中提取结构模态参数。在随机子空间识别方法中,确定系统的阶数是该方法的关键工作,稳定图方法是一种比较新颖的确定系统阶次的方法。但是随机子空间方法容易产生虚假模态,这也是随机子空间方法的一个主要缺陷。因此针对于这一缺陷提出了一种基于两阶段稳定图的随机子空间识别结构模态参数方法,该方法的基本思想是将在现场采集的结构的输出信号进行分段,将各段信号用随机子空间结合稳定图进行识别,然后将所有各段所识别的模态参数再一次用稳定图方法进行分析,得出结构的模态参数。最后用一三跨连续梁的数值模型对该方法进行验证,结果表明该方法具有良好的识别效果。 相似文献
4.
An efficient methodology is presented which uses modal analysis implemented in the frequency domain to obtain the structural response of a system with soil-structure interaction. The interaction effects are represented using a free-field ground motion modification factor, derived for each mode of vibration and used in the determination of structural response. Applying this algorithm, the advantages of the modal superposition method are fully exploited, and the interaction problem can be solved easily and effectively within the framework of the conventional frequency domain analysis for a fixed-base structure. In addition, this method produces accurate approximation with less computational effort due to consideration of only the first few vibration modes of the structure. 相似文献
5.
Studies of structural responses and damage to high-frequency blast motion are very limited. Current practice uses some empirical allowable ground vibration limits in assessing structural performance. These empirical limits overlook the physical parameters that govern structural response and damage, such as the ground motion characteristics and inherent structural properties. This paper studies the response of RC frame structures to numerically simulated underground blast-induced ground motions. The structural response and damage characteristics of frame structures to ground motions of different frequencies are investigated first. The effects of blast ground motion spatial variations and soil–structure interaction on structural responses are also studied. A suitable discrete model that gives accurate response prediction is determined. A damage index defined based on the accumulated plastic hinge rotation is used to predict structural damage level. Numerical results indicated that both the low structural vibration modes (global modes) and the first elemental vibration mode (local) might govern the dynamic structural responses depending on the ground motion frequency and structural response parameters under consideration. Both ground motion spatial variations and soil–structure interaction effects are prominent. Neglecting them might yield inaccurate structural response prediction. The overall structural response and damage are highly ground motion frequency dependent. Numerical results of structural damage are also compared with some test results obtained in a previous study and with code specifications. Discussions on the adequacy of the code allowable ground vibration limits on RC frame structures are also made. 相似文献
6.
Uncertainty analysis of strain modal parameters by Bayesian method using frequency response function
Structural strain modes are able to detect changes in local structural performance, but errors are inevitably intermixed in the measured data. In this paper, strain modal parameters are considered as random variables, and their uncertainty is analyzed by a Bayesian method based on the structural frequency response function (FRF). The estimates of strain modal parameters with maximal posterior probability are determined. Several independent measurements of the FRF of a four-story reinforced concrete frame structural model were performed in the laboratory. The ability to identify the stiffness change in a concrete column using the strain mode was verified. It is shown that the uncertainty of the natural frequency is very small. Compared with the displacement mode shape, the variations of strain mode shapes at each point are quite different. The damping ratios are more affected by the types of test systems. Except for the case where a high order strain mode does not identify local damage, the first order strain mode can provide an exact indication of the damage location. 相似文献
7.
Partial‐strength composite steel–concrete moment‐resisting (MR) frame structures represent an open research field in seismic design from both a theoretical and an experimental standpoint. Among experimental techniques, vibration testing is a well‐known and powerful technique for damage detection, localization and quantification, where actual modal parameters of a structure at different states can be determined from test data by using system identification methods. However, the identification of semi‐rigid connections in framed structures is limited, and hence this paper focuses on a series of vibration experiments that were carried out on a realistic MR frame structure, following the application of pseudo‐dynamic and quasi‐static cyclic loadings at the European laboratory for structural assessment of the Joint Research Centre at Ispra, Italy, with the scope of understanding the structural behaviour and identifying changes in the dynamic response. From the forced vibration response, natural frequencies, damping ratios, modal displacements and rotations were extracted using the circle fitting technique. These modal parameters were used for local and global damage identification by updating a 3D finite element model of the intact structure. The identified results were then correlated with observations performed on the structure to understand further the underlying damage mechanisms. Finally, the latin hypercube sampling technique, a variant of the Monte Carlo method, was employed in order to study the sensitivity of the updated parameters of the 3D model to noise on the modal inputs. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
8.
Structural identification with incomplete output‐only data and independence of measured information for shear‐type systems 
下载免费PDF全文
下载免费PDF全文 Structural identification is the inverse problem of estimating physical parameters of a structural system from its vibration response measurements. Incomplete instrumentation and ambient vibration testing generally result in incomplete and arbitrarily normalized measured modal information, often leading to an ill‐conditioned inverse problem and non‐unique identification results. The identifiability of any parameter set of interest depends on the amount of independent available information. In this paper, we consider the identifiability of the mass and stiffness parameters of shear‐type systems in output‐only situations with incomplete instrumentation. A mode shape expansion‐cum‐mass normalization approach is presented to obtain the complete mass normalized mode shape matrix, starting from the incomplete non‐normalized modes identified using any operational modal analysis technique. An analysis is presented to determine the minimum independent information carried by any given sensor set‐up. This is used to determine the minimum necessary number and location of sensors from the point of view of minimum necessary information for identification. The different theoretical discussions are illustrated using numerical simulations and shake table experiments. It is shown that the proposed identification algorithm is able to obtain reliably accurate physical parameter estimates under the constraints of minimal instrumentation, minimal a priori information, and unmeasured input. The sensor placement rules can be used in experiment design to determine the necessary number and location of sensors on the monitored system. John Wiley & Sons, Ltd. 相似文献
9.
Two approximate methods for decomposing complicated inelastic dynamic responses of wall buildings into simple modal responses are presented. Both methods are based on the equivalent linear concept, where a non‐linear structure is represented by a set of equivalent linear models. One linear model is used for representing only one vibration mode of the non‐linear structure, and its equivalent linear parameters are identified from the inelastic response time histories by using a numerical optimizer. Several theoretical relations essential for the modal decomposition are derived under the framework of complex modal analysis. Various numerical examinations have been carried out to check the validity of the proposed modal decomposition methods, and the results are quite satisfactory in all cases. Fluctuating bending moment and shear at any location along the wall height contributed by each individual vibration mode can be obtained. Modal contributions to shear and flexural strength demands, as well as the corresponding modal properties, under various seismic loading conditions can also be identified and examined in detail. Furthermore, the effects of higher vibration modes on seismic demands of wall buildings are investigated by using the modal decomposition methods. Several new insights into the complicated inelastic dynamics of multi‐story wall buildings are presented. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
10.
An extensive programme of full-scale ambient vibration tests has been conducted to measure the dynamic response of a 542 m (centre span of 274 m) cable-stayed bridge—the Quincy Bayview Bridge in Illinois. A microcomputer-based system was used to collect and analyse the ambient vibration data. A total of 25 modal frequencies and associated mode shapes were identified for the deck structure within the frequency range of 0–2 Hz. Also, estimations were made for damping ratios. The experimental data clearly indicated the occurrence of many closely spaced modal frequencies and spatially complicated mode shapes. Most tower modes were found to be associated with the deck modes, implying a considerable interaction between the deck and tower structure. No detectable levels of motion were evident at the foundation support of the pier. The results of the ambient vibration survey were compared to modal frequencies and mode shapes computed using a three-dimensional finite element model of the bridge. For most modes, the analytic and experimental modal frequencies and mode shapes compare quite well, especially for the vertical modes. Based on the findings of this study, a linear elastic finite element model appears to be capable of capturing much of the complex dynamic behaviour of the bridge with very good accuracy, when compared to the low-level dynamic responses induced by ambient wind and traffic excitations. 相似文献
11.
混凝土框架模型结构参数的识别 总被引：1，自引：1，他引：1
框架结构是常见的建筑结构形式,也是结构损伤诊断的主要研究对象之一。本文以钢筋混凝土框架结构模型的振动测试数据为基础,采用灵敏度分析方法,对结构的物理参数进行识别。有限元分析中,考虑框架结构的节点转动,采用静凝聚方法得到结构刚度矩阵。参数识别结果表明,对于不同的固有频率和振型的测试信息组合所识别的物理参数有所不同。根据已知的概率分布,利用MonteCarlo方法,将模态参数的不确定性传递给物理参数,得到了物理参数的不确定性。 相似文献
12.
The problem of free vibration of non-linear structures is considered initially. It is shown that this problem can be represented as a non-linear eigenvalue problem. Variational principles for non-linear eigenvalue problems are defined. These variational principles are implemented with finite element models to define numerical approximations for the free vibration problem. The solution of these approximate equations provides a set of non-linear modal vectors and natural frequencies which vary with the amplitude of the solution. The non-linear eigenvalue parameters can be used in modal expansion approximations for the non-linear transient or steady state response of structural systems. To demonstrate the proposed techniques the free vibration and steady state vibration characteristics of a geometrically non-linear circular plate are determined. 相似文献
13.
随机子空间方法在桥塔模态参数识别中的应用 总被引：3，自引：0，他引：3
基于环境振动的结构模态参数识别方法正逐渐成为国内外研究的一大热点。环境振动方法就是仅仅利用结构测试的输出信号进行结构的模态参数识别,随机子空间方法就是其中的一种。随机子空间法是近年来发展起来的一种线性系统辩识方法,可以有效地从环境激励的结构响应中获取模态参数。它属于时域的方法,该方法不需要进行FFT变换,它不仅可以识别结构的频率,而且可以识别结构的阻尼和振型。文章首先介绍了随机子空间的理论,然后用该方法对正在施工中的南京长江三桥的南塔进行模态参数识别,通过与其他方法的识别结果进行比较,证明随机子空间方法不失为一种有效的模态参数识别方法。 相似文献
14.
提出了基于经验模式分解（EMD）的环境激励结构模态参数随机子空间识别（SSI）方法。该方法用设置间断频率的EMD将结构环境振动响应原始信号分解成若干个基本模式分量（IMF）,使每一个基本模式分量仅为结构的某一阶固有模态,进而用随机子空间方法进行模态参数识别。实桥环境振动实验分析结果表明,该方法能有效地避免结构各阶模态之间的相互影响,能够更清晰方便地得到结构的模态参数。 相似文献
15.
The dynamic properties of the twenty-two-story, steel-frame San Diego Gas and Electric Company Building in San Diego, California, have been determined experimentally in a series of co-operative tests between the California Institute of Technology and the University of California at Los Angeles. The building was vibrated by two eccentric mass exciters capable of frequencies up to 10 c/sec and forces as much as 5000 Ib each. The natural frequencies, associated mode shapes and the amounts of damping were determined for the first six modes of vibration in each of the two translational directions, and also in torsion. The mode shapes and frequencies showed, in general, the regularity and uniformity that appears typical of many tall buildings, but the three fundamental modes (nominally NS, EW and torsion) of the structure showed a coupling of translational and rotational components to a degree that was unexpected in a building whose structural frame is essentially symmetric. It is believed that this may be a consequence of the exceptionally small differences among the three fundamental frequencies. The damping in the first eighteen modes of the structure varied from 1.6 to 4.4 per cent, with a slight tendency for the larger values to be associated with the higher modes. Of the simpler damping models that might be used for analysis of the building, constant modal damping appears most appropriate and stiffness or mass proportional damping would not be realistic. 相似文献
16.
Vibration-based structural identification is an essential technique for assessing structural conditions by inferring information from the dynamic characteristics of structures. However, the robustness of such techniques in monitoring the progressive damage of real structures has been validated with only a handful of research efforts, largely due to the paucity of monitoring data recorded from damaged structures. In a recent experimental program, a mid-rise cold-formed steel building was constructed at full scale atop a large shake table and subsequently subjected to a unique multi-hazard scenario including earthquake, post-earthquake fire, and finally post-fire earthquake loading. Complementing the simulated hazard events, low-amplitude vibration tests, including ambient vibrations and white noise base excitation tests, were conducted throughout the construction and the test phases. Using the vibration data collected during the multi-hazard test program, this paper focuses on understanding the modal characteristics of the cold-formed steel building in correlation with the construction and the structural damage progressively induced by the simulated hazard events. The modal parameters of the building (i.e., natural frequencies, damping ratios, and mode shapes) are estimated using two input–output and two output-only time-domain system identification techniques. Agreement between the evolution of modal parameters and the observations of the progression of physical damage demonstrates the effectiveness of the vibration-based system identification techniques for structural condition monitoring and damage assessment. 相似文献
17.
Based on the Hilbert–Huang spectral analysis, a method is proposed to identify multi‐degree‐of‐freedom (MDOF) linear systems using measured free vibration time histories. For MDOF systems, the normal modes have been assumed to exist. In this method, the measured response data, which are polluted by noises, are first decomposed into modal responses using the empirical mode decomposition (EMD) approach with intermittency criteria. Then, the Hilbert transform is applied to each modal response to obtain the instantaneous amplitude and phase angle time histories. A linear least‐square fit procedure is proposed to identify the natural frequency and damping ratio from the instantaneous amplitude and phase angle for each modal response. Based on a single measurement of the free vibration time history at one appropriate location, natural frequencies and damping ratios can be identified. When the responses at all degrees of freedom are measured, the mode shapes and the physical mass, damping and stiffness matrices of the structure can be determined. The applications of the proposed method are illustrated using three linear systems with different dynamic characteristics. Numerical simulation results demonstrate that the proposed system identification method yields quite accurate results, and it offers a new and effective tool for the system identification of linear structures in which normal modes exist. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
18.
建立有限元模型是核电厂建筑结构模态分析的重要前提。本文以某高温气冷堆核电厂建筑结构为原型，在分析方法相同的前提下，建立2种不同模型（Solid模型和Shell模型），并对这2种模型进行模态分析。重点分析、对比2种模型的自振频率和振型图，计算分析表明:Solid模型与Shell模型相比，计算得到的结构自振频率值较高，但两者的差异很小，前30阶自振频率相对误差小于3.4%；2种模型的计算结构振型基本一致。研究结果可为核电厂抗震性能分析和设计提供参考。 相似文献
19.
Georges R. Darbre 《地震工程与结构动力学》1984,12(5):703-707
The modal base forces in structures having a straight-line mode of vibration are investigated. Making use of the orthogonality relationship between the different modes, a relation between the modal base shears and base moments is found in all but the straight-line mode. This relation states that the contribution of the inertia forces to the modal overturning moments referred to the centre of rotation of the straight-line mode is identically null. The contributions of the vertical forces and lateral constraints must, however, be accounted for. For the special case of the straight-line mode being proportional to the height of each storey, the centre of rotation coincides with the base of the structure. For the case of the straight-line mode being a uniform displacement, the centre of rotation is at infinity and the contribution of the inertia forces to the modal base shears identically disappears in all but the straight-line mode. 相似文献
20.
Output‐only modal identification is needed when only structural responses are available. As a powerful unsupervised learning algorithm, blind source separation (BSS) technique is able to recover the hidden sources and the unknown mixing process using only the observed mixtures. This paper proposes a new time‐domain output‐only modal identification method based on a novel BSS learning algorithm, complexity pursuit (CP). The proposed concept—independent ‘physical systems’ living on the modal coordinates—connects the targeted constituent sources (and their mixing process) targeted by the CP learning rule and the modal responses (and the mode matrix), which can then be directly extracted by the CP algorithm from the measured free or ambient system responses. Numerical simulation results show that the CP method realizes accurate and robust modal identification even in the closely spaced mode and the highly damped mode cases subject to non‐stationary ambient excitation and provides excellent approximation to the non‐diagonalizable highly damped (complex) modes. Experimental and real‐world seismic‐excited structure examples are also presented to demonstrate its capability of blindly extracting modal information from system responses. The proposed CP is shown to yield clear physical interpretation in modal identification; it is computational efficient, user‐friendly, and automatic, requiring little expertise interactions for implementations. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献