共查询到19条相似文献，搜索用时 140 毫秒
1.
可液化场地大直径扩底桩-土动力相互作用p-y曲线研究对扩底桩抗震设计具有重要意义。基于有限差分程序FLAC~(3D),分别建立扩底桩和等直径桩的三维有限差分模型,通过在模型底部输入正弦波,得到可液化场地中不同埋深下扩底桩与等直径桩的桩-土动力相互作用p-y曲线,对两者的动力p-y曲线特征进行对比分析。结果表明:正弦波输入下扩底桩动力p-y曲线多呈倒"S"形,随着埋深增加,动力p-y曲线滞回圈面积及面积增长速度逐渐减小,斜率逐渐增大;扩底桩与等直径桩动力p-y曲线所围成的图形相似,两者动力p-y曲线斜率均随埋深增加逐渐增大,扩底桩动力p-y曲线滞回圈面积及面积增长速度在各埋深处均大于等直径桩,利于能量耗散,抗震性能更好。 相似文献
2.
桩-液化土相互作用p-y关系分析 总被引：2，自引：0，他引：2
基于多工况的桩-液化土体动力相互作用振动台试验,研究地震荷载作用下液化土层中桩土间侧向相互作用力p与桩身和土体间侧向相对位移y之间的关系。将试验得到的实际p-y曲线与采用拟静力法和以API规范为基础的折减系数法计算出的p-y曲线进行对比,结果表明:(1)液化土层中试验得到的桩真实p-y响应及由拟静力法和折减系数法得到的结果都呈非线性变化,三者极限状态有接近一致的趋势,但变化过程差异明显;(2)采用拟静力法和折减系数法都会使液化土层桩基础侧向反力迅速增长,很快达到屈服极限,远远超过实际情况,会导致相当保守的结果;(3)液化进程中控制桩p-y响应的是土体位移而非惯性力,因而拟静力法和折减系数法的原理不适合桩-液化土体动力相互作用分析,不能用于液化土层中桩基础地震响应的计算。 相似文献
3.
当前桩基础的抗震设计仅采取构造措施来保证其抗震性能,有可能会过高或过低地估计桩基础的抗震性能。针对某桥梁桩基础的抗震设计,建立全桥的三维有限元模型,计算在桩-土-结构共同工作情况下桩基础的地震响应,通过输入不同地震波来进行对比分析,并对结果进行复核,得出:(1)桩身内力响应与所输入地震动的频谱特性有关,桩身沿横桥方向的内力最大;(2)对于该场地的桥梁桩基础,桩-土-结构共同工作的有限元分析结果与m法结果差别不大;(3)当承台埋深为0时,桩身内力基本都偏大,要对承台侧土体做相应的加固处理。 相似文献
4.
《地震工程与工程振动》2021,41(5)
基于OpenSees计算软件建立液化微倾场地群桩-土动力相互作用有限元模型,分析液化微倾场地饱和砂土p-y曲线特性,系统研究了场地倾斜角度、桩径、地震作用幅值和基桩位置对饱和砂土动力p-y曲线特性影响。研究表明:土体即将液化时,桩基土反力达到峰值;土体液化后,土体表现出了流体特性;土反力峰值、桩土相对位移峰值和初始刚度随场地倾斜角度增加而增大;桩径越大,液化砂土的耗能效应越明显;随着地震作用幅值的增加,桩土相对位移峰值和土反力峰值也随之增加;液化微倾场地上坡桩受到的土体侧向流动力大于下坡桩。 相似文献
5.
6.
冲刷造成桩周土体的剥蚀将会削弱土体对桩基的侧向支撑能力,冲刷效应会对桥梁桩基的地震易损性产生影响,因此有必要对冲刷和地震共同作用下桥梁桩基的易损性进行研究。利用SAP2000软件建立三维桥梁有限元模型,通过非线性时程分析得到桥梁桩基地震响应峰值。采用概率性地震需求分析方法,建立不同冲刷深度下桥梁桩基地震易损性模型,在地震易损性函数假设为对数正态分布函数的基础上,通过回归分析得到概率模型中的参数,进而得到不同冲刷深度下桥梁桩基在不同破坏状态所对应的地震易损性曲线,并分析冲刷深度对桩基破坏概率的影响。研究结果表明:随着冲刷深度的增加,桥梁桩基在地震作用下的破坏概率显著增加。 相似文献
7.
8.
水合物分解对桩基础应力和变形影响的研究 总被引：1，自引：0，他引：1
赋存于海底沉积物中的天然气水合物与固体颗粒相互胶结,增加了沉积物的强度,一旦水合物分解,会引起沉积物剪切强度降低,如果在含有水合物层上面或附近存在桩基础,必然影响其稳定性。本文采用应力释放法,通过数值计算,分别讨论了桩基础底部位于含水合物地层不同深度时,水合物分解对桩基础应力和变形的影响规律。计算结果表明,随着水合物分解过程中的模量软化和强度衰减,桩基础的水平和竖向位移增大,由于地基水平,土体没有驱动剪应力,水平位移增加不大,地基和桩基础主要表现为竖向沉降;桩底部位于水合物层中间的桩基础的沉降变形,比桩底穿过水合物层的桩基础大,在桩基础及其附近的土体产生较大的应力。 相似文献
9.
通过进行大型模型槽足尺模型试验,根据桩身变形和柱身弯矩的试验结果,分析了水平荷载作用下现浇混凝土大直径管桩（以下简称PCC桩）的水平承栽特性和桩-土共同作用性状。采用大型通用有限元软件ABAQUS对PCC桩的水平承载特性进行了数值模拟,计算结果与试验结果符合得较好,并进一步探讨了PCC桩水平承载特性的主要影响因素。结果表明：表层土体的弹性模量对水平受力性状影响较大,表层土体的厚度对桩身水平位移也有较大影响,因此可以通过改良表层土体来控制桩身水平位移,以达到工程设计要求;土体强度参数对水平承载特性也有影响,尤其是内摩擦角和粘聚力较小时更为明显。 相似文献
10.
基于通用软件ABAQUS,建立了扩底抗拔桩三维弹塑性有限元模型,通过对模型的计算与分析,探讨了扩底桩的抗拔承载特性。为验证数值模型的可靠性,将数值计算得到的荷载－位移关系曲线与试桩资料进行比较,两者吻合较好,表明本文所建立的模型可较好地模拟扩底抗拔桩的工作性状。通过计算与分析,探讨了扩底抗拔桩的轴力、侧摩阻力分布特征,桩身和扩大头周围土体变形与塑性应变的发展规律,以及扩大头的挤压作用对扩大头周围土体竖向应力的影响。同时,通过变动参数研究了扩大头的形状、土体的性质对扩底桩抗拔承载力的影响,结果表明,扩大头直径和扩大头周围土体的性质对抗拔承载力的影响较大,而扩底高度的影响相对较小。 相似文献
11.
To explore the seismic performance of a high-rise pile cap foundation with riverbed scour, a finite element model for foundations
is introduced in the OpenSees finite element framework. In the model, a fiber element is used to simulate the pile shaft,
a nonlinear p-y element is used to simulate the soil-pile interaction, and the p-factor method is used to reflect the group effects. A global and local scour model is proposed, in which two parameters,
the scour depth of the same row of piles and the difference in the scour depth of the upstream pile and the downstream pile,
are included to study the influence of scour on the foundation. Several elasto-plastic static pushover analyses are performed
on this finite element model. The analysis results indicate that the seismic capacity (or supply) of the foundation is in
the worst condition when the predicted deepest global scout depth is reached, and the capacity becomes larger when the local
scour depth is below the predicted deepest global scout depth. Therefore, to evaluate the seismic capacity of a foundation,
only the predicted deepest global scout depth should be considered. The method used in this paper can be also applied to foundations
with other soil types. 相似文献
12.
Fixed offshore platforms supported by pile foundations are required to resist dynamic lateral loading due to wave forces. The response of a jacket offshore tower is affected by the flexibility and nonlinear behaviour of the supporting piles. For offshore towers supported by clusters of piles, the response to environmental loads is strongly affected by the pile–soil–pile interaction. In the present study, the response of fixed offshore platforms supported by clusters of piles is investigated. The soil resistance to the pile movement is modelled using dynamic p–y curves and t–z curves to account for soil nonlinearity and energy dissipation through radiation damping. The load transfer curves for a single pile have been modified to account for the group effect. The wave forces on the tower members and the tower response are calculated in the time domain using a finite element package (ASAS). Several parameters affecting the dynamic characteristics of the platform and the platform response have been investigated. 相似文献
13.
Owing to their simplicity and reasonable accuracy, Beam on Nonlinear Winkler Foundation (BNWF) models are widely used for the analysis of laterally loaded piles. Their main drawback is idealizing the soil continuum with discrete uncoupled springs representing the soil reactions to pile movement. Static p–y curves, obtained from limited full-scaled field tests, are generally used as a backbone curve of the model. However, these empirically derived p–y curves could not incorporate the effects of various pile properties and soil continuity. The strain wedge method (SWM) has been improved to assess the nonlinear p–y curve response of laterally loaded piles based on a three-dimensional soil–pile interaction through a passive wedge developed in front of the pile. In this paper, the SWM based p–y curve is implemented as the backbone curves of developed BNWF model to study the nonlinear response of single pile under cyclic lateral loading. The developed nonlinear model is capable of accounting for various important soil–pile interaction response features such as soil and pile yielding, cyclic degradation of soil stiffness and strength under generalized loading, soil–pile gap formation with soil cave-in and recompression, and energy dissipation. Some experimental tests are studied to verify the BNWF model and examine the effect of each factor on the response of laterally loaded pile embedded in sand and clay. The experimental data and computed results agree well, confirming the model ability to predict the response of piles under one-way and two-way cyclic loading. The results show that the developed model can satisfactorily simulate the pile stiffness hardening due to soil cave in and sand densification as observed in the experiment. It is also concluded from the results that the gap formation and soil degradation have significant effects on the increase of lateral pile-head deflection and maximum bending moment of the pile in cohesive soils. 相似文献
14.
Hu Yi-li Xu Jun Duan Yong-kong Xu Zhao-yong Yang Run-hai Zhao Jin-ming 《地震学报(英文版)》2004,17(6):725-734
A new method of detecting the vertical bearing capacity for single-pile with high strain is discussed in this paper. A heavy
hammer or a small type of rocket is used to strike the pile top and the detectors are used to record vibration graphs. An
expression of higher degree of strain (deformation force) is introduced. It is testified theoretically that the displacement,
velocity and acceleration cannot be obtained by simple integral acceleration and differential velocity when long displacement
and high strain exist, namely when the pile phase generates a whole slip relative to the soil body. That is to say that there
are non-linear relations between them. It is educed accordingly that the force P and displacement S are calculated from the amplitude of wave train and (dynamic) P-S curve is drew so as to determine the yield points. Further, a method of determining the vertical bearing capacity for single-pile
is discussed. A static load test is utilized to check the result of dynamic test and determine the correlative constants of
dynamic-static P(Q)-S curve.
Foundation item: Key projects of the tenth Five-year Plan of Yunnan Province (documented Yunnan district [2002]54-02-02) and Geophysical
Society of Yunnan Province. 相似文献
15.
Numerical simulations of shake-table experiment for dynamic soil-pile-structure interaction in liquefiable soils 总被引：5，自引：4，他引：1
A shake-table experiment on pile foundations in liquefi able soils composed of liquefi able sand and overlying soft clay is studied. A three-dimensional(3D) effective stress fi nite element(FE) analysis is employed to simulate the experiment. A recently developed multi-surface elasto-plastic constitutive model and a fully coupled dynamic inelastic FE formulation(u-p) are used to model the liquefaction behavior of the sand. The soil domains are discretized using a solid-fl uid fully coupled(u-p) 20-8 noded brick element. The pile is simulated using beam-column elements. Upon careful calibration, very good agreement is obtained between the computed and the measured dynamic behavior of the ground and the pile. A parametric analysis is also conducted on the model to investigate the effect of pile-pinning, pile diameter, pile stiffness, ground inclination angle, superstructure mass and pile head restraints on the ground improvement. It is found that the pile foundation has a noticeable pinning effect that reduces the lateral soil displacement. It is observed that a larger pile diameter and fi xed pile head restraints contribute to decreasing the lateral pile deformation; however, a higher ground inclination angle tends to increase the lateral pile head displacements and pile stiffness, and superstructure mass seems to effectively infl uence the lateral pile displacements. 相似文献
16.
A nonlinear p–y element was provided which can simply model the behavior of a pile group foundation subjected to lateral loading. Its elasto-plastic side soil is expressed as a Winkler-type distributed model. Despite the simplification involved in modeling such a complex phenomenon the proposed nonlinear soil model can reproduce the system behavior as computed by more rigorous 3D finite element methods. The numerical results are also compared with those from available physical model data to confirm that our simulations can predict the behavior of pile groups with good accuracy. 相似文献
17.
Calibration of dynamic analysis methods from field test data 总被引：3，自引：0，他引：3
In view of the heterogeneity of natural soil deposits and approximations made in analysis methods, in situ methods of determining soil parameters are highly desirable. The problem of interest here is the nonlinear dynamic behavior of pile foundations. It is shown in this paper that soil parameters needed for simplified dynamic analysis of a single pile may be back-calculated from the dynamic response of the pile measured in the field. A pile was excited by applying a large horizontal dynamic force at the pile-head level, and the response measured. In this paper, two different (simplified) methods of modeling the dynamic response of the pile are considered. One of the methods is based on the Winkler foundation approach, with the spring constant characterized by the so-called nonlinear p–y springs. The second method is based on the equivalent-linear finite element approach, with the nonlinearity of shear modulus and damping accounted for by employing the so-called degradation relationships. In the latter, the effect of interface nonlinearity is also considered. Starting with best estimates of soil parameters, the experimental data on the response of pile is used to fine-tune the values of the parameters, and thereby, to estimate parameters that are representative of in situ soil conditions. 相似文献
18.
Development and validation of p‐y modeling approach for seismic response predictions of highway bridges 
下载免费PDF全文
下载免费PDF全文 This study aims to realistically simulate the seismic responses of typical highway bridges in California with considerations of soil–structure interaction effects. The p‐y modeling approaches are developed and validated for embankments and pile foundations of bridges. The p‐y approach models the lateral and vertical foundation flexibility with distributed p‐y springs and associated t‐z and q‐z springs. Building upon the existing p‐y models for pile foundations, the study develops the nonlinear p‐y springs for embankments based on nonlinear 2D and 3D continuum finite element analysis under passive loading condition along both longitudinal and transverse directions. Closed‐form expressions are developed for two key parameters, the ultimate resistant force pult and the displacement y50, where 0.5pult is reached, of embankment p‐y models as functions of abutment geometry (wall width and height, embankment fill height, etc.) and soil material properties (wall‐soil friction angle, soil friction angle, and cohesion). In order to account for the kinematic and site responses, depth‐varying ground motions are derived and applied at the free‐end of p‐y springs, which reflects the amplified embankment crest motion. The modeling approach is applied to simulate the seismic responses of the Painter Street Bridge and validated through comparisons with the recorded responses during the 1992 Petrolia earthquake. It is demonstrated that the flexibility and motion amplification at end abutments are the most crucial modeling aspects. The developed p‐y models and the modeling approach can effectively predict the seismic responses of highway bridges. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
19.
传统通过p-y曲线法分析强震状态下黄土中桩基动力性状时未进行桩基结构模拟,获取的强震状态下黄土中桩基动力的相关动力参数不准确。本文提出新的强震状态下黄土中桩基动力性状分析方法,依据HS硬化模型设计HSS本构模型,通过模型获取强震状态下黄土中桩基动力的相关参数,以此为基础采用PLAXIS软件构建黄土中桩基有限元模型;通过两种模型从耦合荷载作用下的桩基桩身水平位移响应、桩身内力响应两方面对强震状态下黄土桩基动力性状展开实验分析。实验结果表明,所提方法可对强震状态下黄土中桩基动力性状进行准确分析。 相似文献