共查询到18条相似文献，搜索用时 125 毫秒
1.
基于能量平衡原理,对多层钢筋混凝土框架结构的地震输入能量的分布及耗散规律进行了研究。选用8条天然地震波和2条人工波,运用Perform-3D软件,对多层钢筋混凝土框架结构模型在7度罕遇地震作用下的弹塑性能量进行数值仿真计算。计算了钢混框架结构在不同地震波下的地震总输入能量、滞回耗能、阻尼耗能以及滞回耗能占总耗能的比例时程,分析了地震能量在各分量中的分布及分配规律;分析了阻尼比和延性比对地震输入能量的影响,确定了滞回耗能随阻尼比和延性比的变化规律;研究了钢筋混凝土框架结构梁柱构造和竖向侧移刚度变化对地震输入能及其分量的影响,确定了多层钢筋混凝土框架结构滞回耗能沿竖向的分布规律及沿横向在框架构件中的分配,研究了框架结构存在薄弱层情况下的滞回耗能的分布规律。揭示了多自由度钢筋混凝土框架结构地震输入能量及其分布规律,可为基于能量平衡原理的抗震设计理论在工程实际中的运用提供有益的参考。 相似文献
2.
利用有限元软件SAP2000建立了某公路简支梁桥的有限元模型，以7条典型强震记录为输入，研究了公路简支梁桥的地震能量响应及其分配规律。结果表明:①地基柔性效应对公路简支梁桥的地震能量响应及其分配规律的影响较小；②当场地土质变软时，地震总输入能、结构阻尼耗能和结构阻尼耗能比均呈递增趋势，而结构滞回耗能和结构滞回耗能比则不断减小，即地基土体作为桥梁动力系统的一部分，增大了系统阻尼，并分担了部分非弹性变形；③随着PGA增大，输入结构的地震能量也增加，导致塑性铰的非弹性变形增加，即结构滞回耗能和结构阻尼耗能增大。 相似文献
3.
本文通过能量法研究了钢筋混凝土筒体结构的抗震性能。文中采用振型分解法按等效单自由度体系求解筒体结构的滞回输入能;用pushover法分析了滞回耗能在结构层间的分布规律及结构自身的耗能能力;根据楼层滞回耗能与弹塑性层间位移的关系求出了薄弱层的弹塑性位移。对一高层钢筋混凝土框架-筒体结构在7度罕遇地震下的抗震性能进行了评估,通过与非线性动力时程分析的对比,证明了方法的可行性。 相似文献
4.
本文通过能量法研究了钢筋混凝土简体结构的抗震性能。文中采用振型分解法按等效单自由度体系求解简体结构的滞回输入能；用pushover法分析了滞回耗能在结构层间的分布规律及结构自身的耗能能力；根据楼层滞回耗能与弹塑性层间位移的关系求出了薄弱层的弹塑性位移。对一高层钢筋混凝土框架-简体结构在7度罕遇地震下的抗震性能进行了评估，通过与非线性动力时程分析的对比，证明了方法的可行性。 相似文献
5.
6.
以17个钢框架-钢筋混凝土剪力墙混合结构为样本,选取结构自振周期T和结构刚度特征值λ作为分析参数,分析它们在不同类型地震动下的地震能量反应。研究表明,混合结构体系在地震作用下总输入能的大小主要与结构的自振周期以及地震动类型有关,剪力墙与钢框架之间的刚度关系对总输入能影响不大;总输入能等效速度谱的形态受地震动类型的影响很大,同一地震动作用下,幅值与等效速度谱值之间基本能够维持线性增长的关系,但随着结构塑性发展的加剧,这种线性增长关系的离散度会变大;在结构自振周期不变化的前提下,结构的滞回耗能比以及底部剪力墙承担滞回耗能的比例都会随结构刚度比的增大而减小。 相似文献
7.
本文研究配有高强钢筋的高强混凝土框架结构的耗能性能与抗震能力.对2层2榀1/2比例的模型结构进行了拟动力试验,分析了高强钢筋的高强混凝土框架结构在地震作用下的滞回反应和耗能能力,探讨了结构在地震作用下的破坏机理,滞回特性及薄弱环节或部位.结构的延性系数达到4.0以上,等效阻尼系数达到0.055以上.试验结果表明,此类结... 相似文献
8.
近年来,能量分析方法在结构抗震设计中的应用问题受到国内外地震工程界的普遍关注,被认为是今后结构抗震设计理论的发展方向之一.以一钢框架-钢筋混凝土剪力墙混合结构为对象,通过逐渐增大框架底层柱截面,分析它们在不同类型地震波下的地震能量反应,结果表明,加强钢框架底层柱使结构总输入能基本不发生变化,结构滞回耗能在总输入能中的比例ν和底部剪力墙滞回耗能占结构总滞回耗能的比例μ均随结构刚度特征值λ的增大而减小,因此,加强钢框架底层柱能够提高外钢框架-内混凝土剪力墙结构体系的抗震能力,降低其在强震作用下的损伤程度. 相似文献
9.
运用能量分析法对并联复合隔震体系的地震耗能机制和能量响应进行了分析和探讨。首先,以层间剪切模型的多自由度运动微分方程为基础,建立了并联复合隔震体系的能量平衡方程。其次,引入状态空间法对并联复合隔震体系进行时程分析得到体系的地震响应,并以此为基础计算了各项能量。最后,以7质点多自由度体系为仿真对象,对并联复合隔震体系的耗能机制及其主要隔震层参数和不同特性地震动对能量响应的影响进行了分析。结果表明,并联复合隔震体系地震总输入能主要由滞回耗能和阻尼耗能承担;摩擦承压比和摩擦系数对能量响应有重要影响,存在最优取值区间;地震能量响应受地震动特性影响较大。 相似文献
10.
通过对5种不同支座布置方案的组合基础隔震结构施加不同场地条件下的双向水平地震波,研究了场地类别和地震波加速度峰值及支座布置方式对结构总输入能量的影响,并进行了耗能分析。结果表明,随着地震波峰值的增大,结构总输入能量增大;相同地震峰值条件下,场地土越软,总的输入能量越大;组合隔震结构应用于软土场地时隔震层滞回耗能比更大,隔震效果更好;组合隔震结构两种支座中选择分散布置方案时,隔震层耗能比更大,隔震效果优于支座集中布置方案。 相似文献
11.
K. K. Wijesundara R. Nascimbene T. J. Sullivan 《Bulletin of Earthquake Engineering》2011,9(5):1535-1558
The direct displacement based seismic design procedure utilises equivalent viscous damping expressions to represent the effect
of energy dissipation of a structural system. Various expressions for the equivalent viscous damping of different structural
systems are available in the literature, but the structural systems examined in the past have not included concentrically
braced frame structures. Thus, this study describes the development of an equivalent viscous damping equation for concentrically
braced frame structures based on the hysteretic response of 15 different single storey models. Initially, equivalent viscous
damping is calculated based on the area based approach and then corrected for the earthquake excitation. An iterative procedure
is adopted to calibrate the equivalent viscous damping expression to the results of inelastic time history analyses using
a number of spectrum-compatible real accelerograms. From the results of this research, a new damping expression is developed
as a function of the ductility and the non dimensional slenderness ratio. 相似文献
12.
本文对具有旗帜型滞回模型的单自由度自复位体系提出了设计能量谱的构造方法,包括设计输入能量谱和设计滞回耗能比谱。首先按中国规范场地类别选取360条实际强震记录进行时程分析,对影响单自由度自复位体系输入能量谱和滞回耗能比谱的参数,包括地震波类型、滞回模型、阻尼比、延性系数等进行研究。在此基础上分别建议了设计输入能量谱和设计滞回耗能比谱及其曲线参数的确定方法,并与实际强震记录计算结果进行比较。结果表明结构滞回模型对能量谱影响明显;阻尼比和延性系数对输入能量谱的影响在整个周期范围内有显著差异,但均有明显的削峰作用。建议的两种设计能量谱综合考虑了结构参数、地震波参数和中国场地类别的影响,可以较好的拟合实际情况,并对弹塑性单自由度自复位体系在地震作用下的耗能需求做出较准确的估计。 相似文献
13.
Dynamic damaging potential of ground motions must be evaluated by the response behaviour of structures, and it is necessary to indicate what properties of ground motions are most appropriate for evaluation. For that purpose, the behaviour of energy input process and hysteretic energy dissipation are investigated in this study. It is found that the momentary input energy that is an index for the intensity of input energy is related to the characteristics of earthquakes such as cyclic or impulsive, and to the response displacement of structures immediately. On the basis of these results, a procedure is proposed to predict inelastic response displacement of structures by corresponding earthquake input energy to structural dissipated damping and hysteretic energy. In this procedure the earthquake response of structures is recognized as an input and dissipation process of energy, and therefore structural properties and damaging properties of ground motions can be taken into account more generally. Lastly, the studies of the pseudodynamic loading test of reinforced concrete structure specimens subjected to ground motions with different time duration are shown. The purpose of this test is to estimate the damaging properties of ground motions and the accuracy of the proposed prediction procedure. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
14.
For the purpose of estimating the earthquake response, particularly the story drift demand, of reinforced concrete (R/C) buildings with proportional hysteretic dampers, an equivalent single‐degree‐of‐freedom (SDOF) system model is proposed. Especially in the inelastic range, the hysteretic behavior of an R/C main frame strongly differs from that of hysteretic dampers due to strength and stiffness degradation in R/C members. Thus, the proposed model, unlike commonly used single‐spring SDOF system models, differentiates the restoring force characteristics of R/C main frame and hysteretic dampers to explicitly take into account the hysteretic behavior of dampers. To confirm the validity of the proposed model, earthquake responses of a series of frame models and their corresponding equivalent SDOF system models were compared. 5‐ and 10‐story frame models were studied as representative of low‐ and mid‐rise building structures, and different mechanical properties of dampers—yield strength and yield deformation—were included to observe their influence on the effectiveness of the proposed model. The results of the analyses demonstrated a good correspondence between estimated story drift demands using the proposed SDOF system model and those of frame models. Moreover, the proposed model: (i) led to better estimates than those given by a single‐spring SDOF system model, (ii) was capable of estimating the input energy demand and (iii) was capable of estimating the total hysteretic energy and the participation of dampers into the total hysteretic energy dissipation, in most cases. Results, therefore, suggest that the proposed model can be useful in structural design practice. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
15.
Seismic performance and damage evaluation of a reinforced concrete frame with hysteretic dampers through shake‐table tests 
下载免费PDF全文
下载免费PDF全文 Passive energy dissipation devices are increasingly implemented in frame structures to improve their performance under seismic loading. Most guidelines for designing this type of system retain the requirements applicable to frames without dampers, and this hinders taking full advantage of the benefits of implementing dampers. Further, assessing the extent of damage suffered by the frame and by the dampers for different levels of seismic hazard is of paramount importance in the framework of performance‐based design. This paper presents an experimental investigation whose objectives are to provide empirical data on the response of reinforced concrete (RC) frames equipped with hysteretic dampers (dynamic response and damage) and to evaluate the need for the frame to form a strong column‐weak beam mechanism and dissipate large amounts of plastic strain energy. To this end, shake‐table tests were conducted on a 2/5‐scale RC frame with hysteretic dampers. The frame was designed only for gravitational loads. The dampers provided lateral strength and stiffness, respectively, three and 12 times greater than those of the frame. The test structure was subjected to a sequence of seismic simulations that represented different levels of seismic hazard. The RC frame showed a performance level of ‘immediate occupancy’, with maximum rotation demands below 20% of the ultimate capacity. The dampers dissipated most of the energy input by the earthquake. It is shown that combining hysteretic dampers with flexible reinforced concrete frames leads to structures with improved seismic performance and that requirements of conventional RC frames (without dampers) can be relieved. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
16.
本文提出了一个近似分析具有滞迟耗能装置的高层建筑的方法。结果被模拟为一个有滞迟非线性支座的悬壁梁。其控制方程由Ｒｉｔｚ法导出，用等效线性化方法分析。 相似文献
17.
消能减震结构设计参数研究与试验验证 总被引：10，自引：1，他引：9
本文就消能减震结构设计参数,即消能部件的支撑刚度、层间最大阻尼力与结构层间屈服力比值等恢复力模型参数的选取进行了讨论。通过对消能装置的耗能特性理论分析,导出了消能装置产生的层间等效阻尼比与这些参数的关系曲线,建议了这些参数的合理取值范围。同时通过对两个消能减震试验结果的分析,验证了本文建议的参数取值的合理性。 相似文献
18.
Changhai Zhai Duofa Ji Weiping Wen Cuihua Li Weidong Lei Lili Xie 《地震工程与工程振动(英文版)》2018,17(2):277-291
Structures located in seismically active regions may be subjected to mainshock-aftershock (MSAS) sequences. Strong aftershocks significantly affect the hysteretic energy demand of structures. The hysteretic energy, EH,seq, is normalized by mass m and expressed in terms of the equivalent velocity, VD,seq, to quantitatively investigate aftershock effects on the hysteretic energy of structures. The equivalent velocity, VD,seq, is computed by analyzing the response time-history of an inelastic single-degree-of-freedom (SDOF) system with a varying vibration period subjected to 309 MSAS sequences. The present study selected two kinds of MSAS sequences, with one aftershock and two aftershocks, respectively. The aftershocks are scaled to maintain different relative intensities. The variation of the equivalent velocity, VD,seq, is studied for consideration of the ductility values, site conditions, relative intensities, number of aftershocks, hysteretic models, and damping ratios. The MSAS sequence with one aftershock exhibited a 10% to 30% hysteretic energy increase, whereas the MSAS sequence with two aftershocks presented a 20% to 40% hysteretic energy increase. Finally, a hysteretic energy prediction equation is proposed as a function of the vibration period, ductility value, and damping ratio to estimate hysteretic energy for mainshock-aftershock sequences. 相似文献