共查询到20条相似文献，搜索用时 22 毫秒
1.
带耗能腋撑竖向不规则短肢剪力墙结构减震性能分析 总被引：2，自引：0，他引：2
在不影响建筑使用空间前提下,提出在抗侧构件不连续处设置耗能腋撑以改善竖向不规则结构抗震性能。以底部大空间短肢剪力墙结构为研究对象,利用大型通用有限元程序ETABS研究耗能器类型与场地土对耗能腋撑工作性能和竖向不规则结构受力性能的影响。研究表明,黏滞型耗能腋撑对文中分析模型各楼层地震反应有较好的控制效果,对转换层处层间位移角与层剪力最大值减幅最大,分别为40.14%和15.66%,对顶层加速度与基底剪力峰值的最大减幅分别为16.06%和23.57%,黏滞型耗能腋撑最大能耗散输入结构能量的42%,而黏弹型耗能腋撑对结构的控制效果不理想;当地震震级较大、震中距较小时,耗能腋撑对坚硬与软弱场地土的模型结构控制作用相差不大,减震位移比在转换层处达到最小值0.76;随着震级减小或震中距增大,耗能腋撑对该模型结构的控制作用随场地土变硬而逐渐增强,其减震位移比介于0.68～0.74之间。 相似文献
2.
摩擦型与软钢屈服型耗能器的性能与减振效果的试验比较 总被引：20，自引：5，他引：20
本文通过两类四种百余个耗能器（其中摩擦类型的两种，普遍摩擦型和Ｐａｌｌ摩擦型；软钢屈服类型的两种：Ｘ钢板和三角钢板屈服型）的静力反复加载和低周疲劳试验，进一步了解这些耗能器的滞回特性和疲劳性能。其次，通过分别安装上述四种耗能器的单层剪切型钢框架模型在输入地震动分别为ＥＩＣｅｎｔｒｏ、Ｔａｆｔ和天津记录等五十余种工况下的振动台试验，较全面地揭示了这些耗能器的减振效果。最后，在试验的基础上较好地建立了 相似文献
3.
Ioannis Politopoulos 《地震工程与结构动力学》2008,37(3):447-465
In this paper the question of possible adverse effects of damping in seismic isolation because of higher mode response is investigated by means of simple models with a few degrees of freedom (DOF). In particular the second mode response of a 2 DOF system is examined in detail for both viscous and hysteretic (e.g. friction or elastoplastic) damping devices. Qualitative and approximate quantitative estimates are obtained by neglecting the influence of the modal coupling terms, due to viscous damping or friction forces, on the first mode response. It is shown that additional viscous damping has a diminishing effect on base displacement, storey shear force and floor spectra values in the vicinity of the first mode resonance. However, a significant amplification of the floor spectra values near the higher mode frequencies may occur. In accordance with the results of previous works, compared with the viscous damping case, hysteretic damping amplifies moderately the first storey shear force and significantly the upper storeys shear force. It also results, in a much more pronounced amplification of the floor spectral values than viscous damping, in the vicinity of the higher eigenfrequencies. However, the higher modes' response is milder if a realistic velocity dependence of the friction coefficient is taken into account. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
4.
提出一种组合型减震结构,由钢框架、节点阻尼器和原结构连接组成,外附钢框架将节点阻尼器连接在原混凝土框架结构上形成的增设节点阻尼器的外附钢框架结构,节点阻尼器的剪切滞回变形可以减小结构自身需要消耗的能量,从而提高原结构抗震性能。对原混凝土结构和增设节点阻尼器的组合型结构进行了的振动台试验。通过分析结构在不同地震波激励下的加速度和位移响应,得出楼层加速度和层位移的减震效果。研究结果表明:该结构体系在小震作用下通过提高结构刚度来增强其抗震性能;在大震作用下则可借助节点阻尼器的变形耗能来提升结构耗能能力,结构加速度减震系数达到53%,层间位移减震系数高达72%,验证了增设节点阻尼器的外附钢框架结构的减震效果。 相似文献
5.
This paper presents an innovative set of high‐seismic‐resistant structural systems termed Advanced Flag‐Shaped (AFS) systems, where self‐centering elements are used with combinations of various alternative energy dissipation elements (hysteretic, viscous or visco‐elasto‐plastic) in series and/or in parallel. AFS systems is developed using the rationale of combining velocity‐dependent with displacement‐dependent energy dissipation for self‐centering systems, particularly to counteract near‐fault earthquakes. Non‐linear time‐history analyses (NLTHA) on a set of four single‐degree‐of‐freedom (SDOF) systems under a suite of 20 far‐field and 20 near‐fault ground motions are used to compare the seismic performance of AFS systems with the conventional systems. It is shown that AFS systems with a combination in parallel of hysteretic and viscous energy dissipations achieved greater performance in terms of the three performance indices. Furthermore, the use of friction slip in series of viscous energy dissipation is shown to limit the peak response acceleration and induced base‐shear. An extensive parametric analysis is carried out to investigate the influence of two design parameters, λ1 and λ2 on the response of SDOF AFS systems with initial periods ranging from 0.2 to 3.0 s and with various strength levels when subjected to far‐field and near‐fault earthquakes. For the design of self‐centering systems with combined hysteretic and viscous energy dissipation (AFS) systems, λ1 is recommended to be in the range of 0.8–1.6 while λ2 to be between 0.25 and 0.75 to ensure sufficient self‐centering and energy dissipation capacities, respectively. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
6.
Choice between series and parallel connections of hysteretic system and viscous damper for seismic protection of structures 
下载免费PDF全文
下载免费PDF全文 Supplemental viscous damping devices are generally envisioned to be connected in parallel to the inelastic parent structure or hysteretic damping devices. This gives rise to higher base shear, and often greater ductility demand of the hysteretic system. The series connection of the viscous and hysteretic system (the inelastic structure or a damper) is an alternative approach. In this paper, comparisons between the series and parallel connections of the hysteretic system and viscous dampers are done through response spectra analyses of single degree of freedom structures. Ductility demand of the hysteretic system and the total base shear are chosen as the response quantities. For the series model, a semi‐implicit solution scheme for classical Maxwell model is modified to include the inelasticity of the time‐independent hysteretic spring. It is observed that the series connection of the 2 dampers gives lower base shear than does the parallel connection. For long‐period and low‐damping structures, the ductility demand of the hysteretic system in series connection is higher than that in parallel connection. Increasing the viscous damping in series connection reduces the ductility demand substantially, lower than that obtained in parallel connection. Practical methods for implementing the series and parallel connections, in line with roof isolation, are also suggested. 相似文献
7.
对巨型框架-耗能支撑结构新体系进行了罕遇地震作用下的弹塑性时程分析,研究该体系的减震性能和耗能支撑的不同布置方式对结构的减震效果。结果表明:如果耗能支撑布置位置得当,可以用较少的耗能支撑个数达到较好的减震效果;巨型框架-耗能支撑结构不但可以减少原巨型框架-支撑结构的层间侧移,还可以减少其底部剪力和顶层加速度反应的峰值。 相似文献
8.
The concentrically braced frame (CBF) structure is one of the most efficient steel structural systems to resist earthquakes. This system can dissipate energy during earthquakes through braces, which are expected to yield in tension and buckle in compression, while all other elements such as columns, beams and connections are expected to behave elastically. In this paper, the performance of single‐storey CBFs is assessed with nonlinear time‐history analysis, where a robust numerical model that simulates the behaviour of shake table tests is developed. The numerical model of the brace element used in the analysis was calibrated using data measured in physical tests on brace members subjected to cyclic loading. The model is then validated by comparing predictions from nonlinear time‐history analysis to measured performance of brace members in full scale shake table tests. Furthermore, the sensitivity of the performance of the CBF to different earthquake ground motions is investigated by subjecting the CBF to eight ground motions that have been scaled to have similar displacement response spectra. The comparative assessments presented in this work indicate that these developed numerical models can accurately capture the salient features related to the seismic behaviour of CBFs. A good agreement is found between the performance of the numerical and physical models in terms of maximum displacement, base shear force, energy dissipated and the equivalent viscous damping. The energy dissipated and, more particular, the equivalent viscous damping, are important parameters required when developing an accurate displacement‐based design methodology for CBFs subjected to earthquake loading. In this study, a relatively good prediction of the equivalent viscous damping is obtained from the numerical model when compared with data measured during the shake table tests. However, it was found that already established equations to determine the equivalent viscous damping of CBFs may give closer values to those obtained from the physical tests. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
9.
This paper discusses the importance of including the bond‐slip effects in assessing the response under cyclic loads of reinforced concrete frames. The discussion is based on analyses performed using numerical models which are simple, computationally efficient and capable of representing the salient features of reinforced concrete frames under both static and dynamic loads. The numerical models comprise a displacement‐based, reinforced concrete frame element with bond‐slip and a rigid beam column joint element with bond‐slip. Two applications illustrate the model accuracy and show the importance of including bond‐slip. The first application considers a reinforced concrete beam‐column subassemblage experimentally tested under cyclic loads. The second application considers the shaking table test of a two‐story one‐bay reinforced concrete frame In both cases the analytical results correlate well with the experimental results in terms of strength, displacement demands and hysteretic energy dissipation. Furthermore, the paper shows how the analyses that include bond‐slip yield a better correlation with the experimental results with respect to the analyses that assume a perfect bond. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
10.
T. Akiyoshi 《地震工程与结构动力学》1982,10(1):135-148
The interaction between a soil layer and an end bearing pile in vertical vibration induced through the frictional interface is theoretically investigated. The pile is assumed to be vertical and elastic, whereas the soil is considered as a linear visco-elastic layer with hysteretic damping. Slip between the pile and the soil is allowed to occur along the frictional interface, in which the hysteretic frictional stress is linearized to permit modal decomposition. Approximate solutions of the pile and the soil for steady-harmonic loads are obtained in closed form by composing the wave modes of the layer. The displacement amplitudes of the pile and the soil, the critical slip force, the stiffness of the pile head, and the modal stiffness contribution of the soil to the pile are evaluated numerically with respect to the ratio of applied force level to the slip stress level and the slenderness ratio, at various frequencies. 相似文献
11.
This paper explores the influence of linear hysteretic damping on the performance of passive tuned-inerter devices. An inerter is a device that produces a force proportional to the relative acceleration across its two terminals; devices incorporating inerters have received widespread attention in the earthquake engineering community, because they offer the ability to improve the seismic response of structures. However, the majority of this research has assumed that the damping components within the tuned-inerter device exhibit viscous, rather than hysteretic, damping. This restriction imposes an essential question on how the hysteretic damping model will change the performance of the device compared with the viscous damping model. It is shown that the response of viscous and hysteretic inerter systems have significant differences in displacement amplitude due to the frequency dependency of the damping. Therefore, a new formulation for obtaining the optimum loss factor of the hysteretic damping in the inerter system is proposed. Next, the challenges associated with accurately predicting the time-response of a hysteretically damped system are discussed. A numerical time-integration method is extended to address these challenges, using a new formulation that has the benefit of being broadly applicable to multidegree-of-freedom hysteretic linear systems and nonstationary random signals. The results show that the earthquake responses from the hysteretic damping model can differ significantly from the ones obtained via the viscous model. 相似文献
12.
考虑场地类别与强震持时的滞回耗能谱的特征分析 总被引：3，自引：0，他引：3
基于力或位移的结构抗震设计方法大多无法反映地震动持时的影响,而能量设计方法则能较好地弥补其不足。按场地类别和强震持时,将302条Northridge地震记录分为15组,对地震记录的峰值进行规一化处理,采用钢筋混凝土退化三线型恢复力模型,对单自由度体系进行弹塑性时程分析,研究场地类别、强震持时、强度屈服水平以及结构周期等因素对滞回耗能的影响。结果表明:在给定地震记录的峰值和屈服强度水平下,结构的滞回耗能依赖于场地条件和强震持时等因素;滞回耗能随强震持时的增加而增大,随场地特征周期的增加而增大。通过非线性回归分析,建立了与峰值加速度、峰值速度、强震持时相对应的简化滞回耗能谱的计算公式。 相似文献
13.
根据基础隔震理论,在钢筋沥青隔震礅的基础上,提出一种新型钢结构隔震礅,设计和制作了缩尺房屋模型,并对其进行振动台试验。通过对隔震结构模型的动力特性、地震响应及能量平衡分析,绘制试验过程中的加速度及能量时程曲线,研究钢隔震礅应用于低层框架结构的减震耗能能力。大量工程实例可以看出该隔震礅隔震效果显著,制作简单、价格低廉、耐久性好,适于在广大村镇地区低层框架结构中推广使用。试验表明:隔震结构模型在不同的地震作用下,加速度折减系数处在0.24~0.51之间,且结构的阻尼耗能在振动台试验中占总输入能量的60%~70%,对结构耗能起主导作用,说明该基础隔震装置不仅具有较好的减震耗能特性能,对于控制隔震层的位移也有好的效果。 相似文献
14.
Geoffrey W. Rodgers John B. Mander J. Geoffrey Chase Kerry J. Mulligan Bruce L. Deam Athol Carr 《地震工程与结构动力学》2007,36(1):77-100
Semi‐active dampers offer significant capability to reduce dynamic wind and seismic structural response. A novel resetable device with independent valve control laws that enables semi‐active re‐shaping of the overall structural hysteretic behaviour has been recently developed, and a one‐fifth scale prototype experimentally validated. This research statistically analyses three methods of re‐shaping structural hysteretic dynamics in a performance‐based seismic design context. Displacement, structural force, and total base‐shear response reduction factor spectra are obtained for suites of ground motions from the SAC project. Results indicate that the reduction factors are suite invariant. Resisting all motion adds damping in all four quadrants and showed 40–60% reductions in the structural force and displacement at the cost of a 20–60% increase in total base‐shear. Resisting only motion away from equilibrium adds damping in quadrants 1 and 3, and provides reductions of 20–40%, with a 20–50% increase in total base‐shear. However, only resisting motion towards equilibrium adds damping in quadrants 2 and 4 only, for which the structural responses and total base‐shear are reduced 20–40%. The spectral analysis results are used to create empirical reduction factor equations suitable for use in performance based design methods, creating an avenue for designing these devices into structural applications. Overall, the reductions in both response and base‐shear indicate the potential appeal of this semi‐active hysteresis sculpting approach for seismic retrofit applications—largely due to the reduction of the structural force and overturning demands on the foundation system. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
15.
球罐作为石油化工行业的重要存储容器,一旦在服役期间发生破坏,不仅将造成重大经济损失,而且易发生重大人员伤亡事故。用ADINA分析软件建立了球罐的设计模型及简化理论模型,并研究了附加粘滞阻尼器的速度指数与配置方案对球形储液罐减震的影响。利用达朗贝尔原理建立动力方程,采用非线性动力方程计算其基底剪力值,与有限元法计算结果对比分析。研究结果表明:当速度指数为0.3的时候,在地震动作用下其结构柱顶的加速度变大;当速度指数大于等于0.7时,滞回曲线明显变扁,耗能减震的效率降低到15%以下。相对于全布置方案,按方案7在布置粘滞性阻尼器,球罐基底剪力、柱顶速度、柱顶位移、拉杆应力及拉杆拉力的控制上,效果能达到全布置方案的60%以上,在波高的控制上能达到70%以上。有限元验算与计算结果较为吻合,可为后续的研究应用提供参考依据。粘滞阻尼器有助于球罐结构减震,但粘滞阻尼器的参数和配置方案应综合考虑工程的实际情况而定。 相似文献
16.
K. K. Wijesundara R. Nascimbene T. J. Sullivan 《Bulletin of Earthquake Engineering》2011,9(5):1535-1558
The direct displacement based seismic design procedure utilises equivalent viscous damping expressions to represent the effect
of energy dissipation of a structural system. Various expressions for the equivalent viscous damping of different structural
systems are available in the literature, but the structural systems examined in the past have not included concentrically
braced frame structures. Thus, this study describes the development of an equivalent viscous damping equation for concentrically
braced frame structures based on the hysteretic response of 15 different single storey models. Initially, equivalent viscous
damping is calculated based on the area based approach and then corrected for the earthquake excitation. An iterative procedure
is adopted to calibrate the equivalent viscous damping expression to the results of inelastic time history analyses using
a number of spectrum-compatible real accelerograms. From the results of this research, a new damping expression is developed
as a function of the ductility and the non dimensional slenderness ratio. 相似文献
17.
基于能量平衡原理,对多层钢筋混凝土框架结构的地震输入能量的分布及耗散规律进行了研究。选用8条天然地震波和2条人工波,运用Perform-3D软件,对多层钢筋混凝土框架结构模型在7度罕遇地震作用下的弹塑性能量进行数值仿真计算。计算了钢混框架结构在不同地震波下的地震总输入能量、滞回耗能、阻尼耗能以及滞回耗能占总耗能的比例时程,分析了地震能量在各分量中的分布及分配规律;分析了阻尼比和延性比对地震输入能量的影响,确定了滞回耗能随阻尼比和延性比的变化规律;研究了钢筋混凝土框架结构梁柱构造和竖向侧移刚度变化对地震输入能及其分量的影响,确定了多层钢筋混凝土框架结构滞回耗能沿竖向的分布规律及沿横向在框架构件中的分配,研究了框架结构存在薄弱层情况下的滞回耗能的分布规律。揭示了多自由度钢筋混凝土框架结构地震输入能量及其分布规律,可为基于能量平衡原理的抗震设计理论在工程实际中的运用提供有益的参考。 相似文献
18.
A combined energy dissipation system is developed in this paper. In this system lead rubber dampers and their parallel connection with oil dampers are used in the braces of a structural frame. A dynamic analysis method of the system, including the modelling of the lead rubber damper and the oil damper, is proposed. In the analysis method, the restoring force characterestics of the lead rubber damper is simulated by the Bouc–Wen hysteretic model, and the behaviour of the oil damper is simulated by a velocity and displacement‐related model in which the contributions of the oil damper to the damping force and stiffness of the system are considered. A series of shaking table tests of a three‐storey steel frame with the combined energy dissipation system are carried out to evaluate the performance of the system and to verify the analysis method. The test and analysis show that the performance of the combined energy dissipation system is quite satisfactory and there is a good agreement between the analysis and test results, which indicates that the analysis method proposed in this paper is valid and suitable for the dynamic analysis of the combined energy dissipation system. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
19.
Geoffrey W. Rodgers Kevin M. Solberg J. Geoffrey Chase John B. Mander Brendon A. Bradley Rajesh P. Dhakal Luoman Li 《地震工程与结构动力学》2008,37(13):1549-1564
Ductile‐jointed connections, which generally require some form of supplementary energy dissipation to alleviate displacement response, typically employ mild steel energy dissipation devices. These devices run the risk of low‐cycle fatigue, are effective only for peak cycles that exceed prior displacements, are prone to buckling, and may require replacement following an earthquake. This study presents an experimental investigation employing an alternative to mild steel: a high force‐to‐volume (HF2V) class of damper‐based energy dissipation devices. Tests are performed on a near full‐scale beam–column joint subassembly utilizing externally mounted compact HF2V devices. Two configurations are considered: an exterior joint with two seismic beams and one gravity beam framing into a central column, and a corner joint with only one seismic beam and one gravity beam framing into a column. Quasi‐static tests are performed to column drifts up to 4%. The experiments validate the efficacy of the HF2V device concept, demonstrating good hysteretic energy dissipation, and minimal residual device force, allowing ready re‐centring of the joint. The devices dissipate energy consistently on every cycle without the deterioration observed in the yielding steel bar type of devices. The effectiveness of the HF2V devices on structural hysteretic behavior is noted to be sensitive to the relative stiffness of the anchoring elements, indicating that better efficiency would be obtained in an embedded design. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献