首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 359 毫秒
1.
The recent use of marine electromagnetic technology for exploration geophysics has primarily focused on applying the controlled source electromagnetic method for hydrocarbon mapping. However, this technology also has potential for structural mapping applications, particularly when the relative higher frequency controlled source electromagnetic data are combined with the lower frequencies of naturally occurring magnetotelluric data. This paper reports on an extensive test using data from 84 marine controlled source electromagnetic and magnetotelluric stations for imaging volcanic sections and underlying sediments on a 128‐km‐long profile. The profile extends across the trough between the Faroe and Shetland Islands in the North Sea. Here, we focus on how 2.5D inversion can best recover the volcanic and sedimentary sections. A synthetic test carried out with 3D anisotropic model responses shows that vertically transverse isotropy 2.5D inversion using controlled source electromagnetic and magnetotelluric data provides the most accurate prediction of the resistivity in both volcanic and sedimentary sections. We find the 2.5D inversion works well despite moderate 3D structure in the synthetic model. Triaxial inversion using the combination of controlled source electromagnetic and magnetotelluric data provided a constant resistivity contour that most closely matched the true base of the volcanic flows. For the field survey data, triaxial inversion of controlled source electromagnetic and magnetotelluric data provides the best overall tie to well logs with vertically transverse isotropy inversion of controlled source electromagnetic and magnetotelluric data a close second. Vertical transverse isotropy inversion of controlled source electromagnetic and magnetotelluric data provided the best interpreted base of the volcanic horizon when compared with our best seismic interpretation. The structural boundaries estimated by the 20‐Ω·m contour of the vertical resistivity obtained by vertical transverse isotropy inversion of controlled source electromagnetic and magnetotelluric data gives a maximum geometric location error of 11% with a mean error of 1.2% compared with the interpreted base of the volcanic horizon. Both the model study and field data interpretation indicate that marine electromagnetic technology has the potential to discriminate between low‐resistivity prospective siliciclastic sediments and higher resistivity non‐prospective volcaniclastic sediments beneath the volcanic section.  相似文献   

2.
Time‐domain marine controlled source electromagnetic methods have been used successfully for the detection of resistive targets such as hydrocarbons, gas hydrate, or marine groundwater aquifers. As the application of time‐domain marine controlled source electromagnetic methods increases, surveys in areas with a strong seabed topography are inevitable. In these cases, an important question is whether bathymetry information should be included in the interpretation of the measured electromagnetic field or not. Since multi‐dimensional inversion is still not common in time‐domain marine controlled source electromagnetic methods, bathymetry effects on the 1D inversion of single‐offset and multi‐offset joint inversions of time‐domain controlled source electromagnetic methods data are investigated. We firstly used an adaptive finite element algorithm to calculate the time‐domain controlled source electromagnetic methods responses of 2D resistivity models with seafloor topography. Then, 1D inversions are applied on the synthetic data derived from marine resistivity models, including the topography in order to study the possible topography effects on the 1D interpretation. To evaluate the effects of topography with various steepness, the slope angle of the seabed topography is varied in the synthetic modelling studies for deep water (air interaction is absent or very weak) and shallow water (air interaction is dominant), respectively. Several different patterns of measuring configurations are considered, such as the systems adopting nodal receivers and the bottom‐towed system. According to the modelling results for deep water when air interaction is absent, the 2D topography can distort the measured electric field. The distortion of the data increases gradually with the enlarging of the topography's slope angle. In our test, depending on the configuration, the seabed topography does not affect the 1D interpretation significantly if the slope angle is less or around 10°. However, if the slope angle increases to 30° or more, it is possible that significant artificial layers occur in inversion results and lead to a wrong interpretation. In a shallow water environment with seabed topography, where the air interaction dominates, it is possible to uncover the true subsurface resistivity structure if the water depth for the 1D inversion is properly chosen. In our synthetic modelling, this scheme can always present a satisfactory data fit in the 1D inversion if only one offset is used in the inversion process. However, the determination of the optimal water depth for a multi‐offset joint inversion is challenging due to the various air interaction for different offsets.  相似文献   

3.
This paper presents the first controlled‐source electromagnetic survey carried out in the German North Sea with a recently developed seafloor‐towed electrical dipole–dipole system, i.e., HYDRA II. Controlled‐source electromagnetic data are measured, processed, and inverted in the time domain to estimate an electrical resistivity model of the sub‐seafloor. The controlled‐source electromagnetic survey targeted a shallow, phase‐reversed, seismic reflector, which potentially indicates free gas. To compare the resistivity model to reflection seismic data and draw a combined interpretation, we apply a trans‐dimensional Bayesian inversion that estimates model parameters and uncertainties, and samples probabilistically over the number of layers of the resistivity model. The controlled‐source electromagnetic data errors show time‐varying correlations, and we therefore apply a non‐Toeplitz data covariance matrix in the inversion that is estimated from residual analysis. The geological interpretation drawn from controlled‐source electromagnetic inversion results and borehole and reflection seismic data yield resistivities of ～1 Ωm at the seafloor, which are typical for fine‐grained marine deposits, whereas resistivities below ～20 mbsf increase to 2–4 Ωm and can be related to a transition from fine‐grained (Holocene age) to unsorted, coarse‐grained, and compacted glacial sediments (Pleistocene age). Interface depths from controlled‐source electromagnetic inversion generally match the seismic reflector related to the contrast between the different depositional environments. Resistivities decrease again at greater depths to ～1 Ωm with a minimum resistivity at ～300 mbsf where a seismic reflector (that marks a major flooding surface of late Miocene age) correlates with an increased gamma‐ray count, indicating an increased amount of fine‐grained sediments. We suggest that the grain size may have a major impact on the electrical resistivity of the sediment with lower resistivities for fine‐grained sediments. Concerning the phase‐reversed seismic reflector that was targeted by the survey, controlled‐source electromagnetic inversion results yield no indication for free gas below it as resistivities are generally elevated above the reflector. We suggest that the elevated resistivities are caused by an overall decrease in porosity in the glacial sediments and that the seismic reflector could be caused by an impedance contrast at a thin low‐velocity layer. Controlled‐source electromagnetic interface depths near the reflector are quite uncertain and variable. We conclude that the seismic interface cannot be resolved with the controlled‐source electromagnetic data, but the thickness of the corresponding resistive layer follows the trend of the reflector that is inclined towards the west.  相似文献   

4.
Accurate well ties are essential to practical seismic lithological interpretation. As long as the geology in the vicinity of the reservoir is not unduly complex, the main factors controlling this accuracy are the processing of the seismic data and the construction of the seismic model from well logs. This case study illustrates how seismic data processing to a near-offset stack, quality control of logs and petrophysical modelling improved a well tie at an oil reservoir. We demonstrate the application of a predictive petrophysical model in the preparation and integration of the logs before building the seismic model and we quantify our improvements in well-tie accuracy. The data for the study consisted of seismic field data from a 3D sail line through a well in a North Sea oilfield and a suite of standard logs at the well. A swathe of fully processed 3D data through the well was available for comparison. The well tie in the shallow section from first-pass seismic data processing and a routinely edited sonic log was excellent. The tie in a deeper interval containing the reservoir was less satisfactory: the phase errors within the bandwidth of the seismic wavelet were of the order of 20°, which we consider too large for subsequent transformation of the data to seismic impedance. Reprocessing the seismic data and revision of the well-log model reduced these phase errors to less than 10° and improved the consistency of the deep and shallow well ties. The reprocessing included densely picked iterative velocity analysis, prestack migration, beam-forming multiple attenuation, stacking the near-offset traces and demigration and remigration of the near-offset data. The petrophysical model was used to monitor and, where necessary, replace the P-wave sonic log with predictions consistent with other logs and to correct the sonic log for mud-filtrate invasion in the hydrocarbon-bearing sand. This editing and correction of the P-wave transit times improved the normal-incidence well tie significantly. The recordings from a monopole source severely underestimated the S-wave transit times in soft shale formations, including the reservoir seal, where the S-wave velocity was lower than the P-wave velocity in the drilling mud. The petrophysical model predicted an S-wave log that matched the valid recordings and interpolated between them. The subsequent seismic modelling from the predicted S-wave log produced a class II AVO anomaly seen on the CDP gathers around the well.  相似文献   

5.
We conducted a laboratory study of the joint elastic‐electrical properties of sixty‐three brine‐saturated sandstone samples to assess the likely impact of differential pressure (confining minus pore fluid pressures) in the range 8–60 MPa on the joint interpretation of marine seismic and controlled‐source electromagnetic survey data. The samples showed a wide range of petrophysical properties representative of most sandstone reservoirs. We found that a regression equation comprising both a constant and an exponential part gave a good fit to the pressure dependence of all five measured geophysical parameters (ultrasonic P‐ and S‐wave velocity, attenuation and electrical resistivity). Electrical resistivity was more pressure‐sensitive in clay‐rich sandstones with higher concentrations of low aspect ratio pores and micropores than in clean sandstones. Attenuation was more pressure‐sensitive in clean sandstones with large open pores (macropores) than in clay‐rich sandstones. Pore shape did not show any influence on the pressure sensitivity of elastic velocity. As differential pressure increases, the effect of the low aspect ratio pores and micropores on electrical resistivity becomes stronger than the effect of the macropores on attenuation. Further analysis of correlations among the five parameters as a function of pressure revealed potentially diagnostic relationships for geopressure prediction in reservoir sandstones.  相似文献   

6.
We developed a new marine controlled‐source electromagnetic receiver for detecting methane hydrate zones and oil and gas reservoirs on the seafloor, which is not imaged well by seismic reflection surveys. To determine the seafloor structure, the electromagnetic receiver should have low noise, power consumption, clock drift error, and operating costs while being highly reliable. Because no suitable receiver was available in our laboratory, we developed a new marine controlled‐source electromagnetic receiver with these characteristics; the receiver is equipped with acoustic telemetry modem and an arm‐folding mechanism to facilitate deployment and recovering operations. To demonstrate the applicability of our new receiver, we carried out a field experiment offshore of Guangzhou in the South China Sea, where methane hydrates have been discovered. We successfully obtained controlled‐source electromagnetic data along a profile about 13 km long. All six new receivers were recovered, and high‐quality electromagnetic data were obtained. Relatively high apparent resistivity values were detected. The results of the offshore field experiment support the claim that the electromagnetic data obtained using the new receiver are of sufficient quality for the survey target.  相似文献   

7.
We present results of synthetic time‐lapse and real repeatability multi‐transient electromagnetic surveys over the North Sea Harding field. Using Archie's law to convert porosity and fluid saturation to resistivity we created 3D isotropic models of the reservoir resistivity at different stages of production from the initial state in 1996 through to complete hydrocarbon production by 2016 and, for each stage, we simulated an east‐west transient electromagnetic survey line across Harding. Unconstrained 1D full‐waveform Occam inversions of these synthetic data show that Harding should be detectable and its lateral extent reasonably well‐defined. Resistivity changes caused by hydrocarbon production from initial pre‐production state to production of the oil rim in 2011 are discernible as are significant changes from 2011–2016 during the modelled gas blowdown phase. The 2D repeatability surveys of 2007 and 2008 tied two wells: one on and the other off the structure. Between the two surveys the segment of the field under investigation produced 3.9 million barrels of oil – not enough to generate an observable time‐lapse electromagnetic anomaly with a signal‐to‐noise ratio of 40 dB. Processing of the 2007 and 2008 data included deconvolution for the measured source current and removal of spatially‐correlated noise, which increased the signal‐to‐noise ratio of the recovered impulse responses by about 20 dB and resulted in a normalized root‐mean‐square difference of 3.9% between the data sets. 1D full‐waveform Occam inversions of the real data showed that Harding was detectable and its lateral extent was also reasonably well‐defined. The results indicate that the multi‐transient electromagnetic method is suitable for exploration, appraisal and monitoring hydrocarbon production.  相似文献   

8.
In order to perform resistivity imaging, seismic waveform tomography or sensitivity analysis of geophysical data, the Fréchet derivatives, and even the second derivatives of the data with respect to the model parameters, may be required. We develop a practical method to compute the relevant derivatives for 2.5D resistivity and 2.5D frequency-domain acoustic velocity inversion. Both geophysical inversions entail the solution of a 2.5D Helmholtz equation. First, using differential calculus and the Green's functions of the 2.5D Helmholtz equation, we strictly formulate the explicit expressions for the Fréchet and second derivatives, then apply the finite-element method to approximate the Green's functions of an arbitrary medium. Finally, we calculate the derivatives using the expressions and the numerical solutions of the Green's functions. Two model parametrization approaches, constant-point and constant-block, are suggested and the computational efficiencies are compared. Numerical examples of the derivatives for various electrode arrays in cross-hole resistivity imaging and for cross-hole seismic surveying are demonstrated. Two synthetic experiments of resistivity and acoustic velocity imaging are used to illustrate the method.  相似文献   

9.
We measured in the laboratory ultrasonic compressional and shear‐wave velocity and attenuation (0.7–1.0 MHz) and low‐frequency (2 Hz) electrical resistivity on 63 sandstone samples with a wide range of petrophysical properties to study the influence of reservoir porosity, permeability and clay content on the joint elastic‐electrical properties of reservoir sandstones. P‐ and S‐wave velocities were found to be linearly correlated with apparent electrical formation factor on a semi‐logarithmic scale for both clean and clay‐rich sandstones; P‐ and S‐wave attenuations showed a bell‐shaped correlation (partial for S‐waves) with apparent electrical formation factor. The joint elastic‐electrical properties provide a way to discriminate between sandstones with similar porosities but with different clay contents. The laboratory results can be used to estimate sandstone reservoir permeability from seismic velocity and apparent formation factor obtained from co‐located seismic and controlled source electromagnetic surveys.  相似文献   

10.
Improvements in the joint inversion of seismic and marine controlled source electromagnetic data sets will require better constrained models of the joint elastic‐electrical properties of reservoir rocks. Various effective medium models were compared to a novel laboratory data set of elastic velocity and electrical resistivity (obtained on 67 reservoir sandstone samples saturated with 35 g/l brine at a differential pressure of 8 MPa) with mixed results. Hence, we developed a new three‐phase effective medium model for sandstones with pore‐filling clay minerals based on the combined self‐consistent approximation and differential effective medium model. We found that using a critical porosity of 0.5 and an aspect ratio of 1 for all three components, the proposed model gave accurate model predictions of the observed magnitudes of P‐wave velocity and electrical resistivity and of the divergent trends of clean and clay‐rich sandstones at higher porosities. Using only a few well‐constrained input parameters, the new model offers a practical way to predict in situ porosity and clay content in brine saturated sandstones from co‐located P‐wave velocity and electrical resistivity data sets.  相似文献   

11.
Z‐axis tipper electromagnetic and broadband magnetotelluric data were used to determine three‐dimensional electrical resistivity models of the Morrison porphyry Cu–Au–Mo deposit in British Columbia. Z‐axis tipper electromagnetic data are collected with a helicopter, thus allowing rapid surveys with uniform spatial sampling. Ground‐based magnetotelluric surveys can achieve a greater exploration depth than Z‐axis tipper electromagnetic surveys, but data collection is slower and can be limited by difficult terrain. The airborne Z‐axis tipper electromagnetic tipper data and the ground magnetotelluric tipper data show good agreement at the Morrison deposit despite differences in the data collection method, spatial sampling, and collection date. Resistivity models derived from individual inversions of the Z‐axis tipper electromagnetic tipper data and magnetotelluric impedance data contain some similar features, but the Z‐axis tipper electromagnetic model appears to lack resolution below a depth of 1 km, and the magnetotelluric model suffers from non‐uniform and relatively sparse spatial sampling. The joint Z‐axis tipper electromagnetic inversion solves these issues by combining the dense spatial sampling of the airborne Z‐axis tipper electromagnetic technique and the deeper penetration of the lower frequency magnetotelluric data. The resulting joint resistivity model correlates well with the known geology and distribution of alteration at the Morrison deposit. Higher resistivity is associated with the potassic alteration zone and volcanic country rocks, whereas areas of lower resistivity agree with known faults and sedimentary units. The pyrite halo and ≥0.3% Cu zone have the moderate resistivity that is expected of disseminated sulphides. The joint Z‐axis tipper electromagnetic inversion provides an improved resistivity model by enhancing the lateral and depth resolution of resistivity features compared with the individual Z‐axis tipper electromagnetic and magnetotelluric inversions. This case study shows that a joint Z‐axis tipper electromagnetic–magnetotelluric approach effectively images the interpreted mineralised zone at the Morrison deposit and could be beneficial in exploration for disseminated sulphides at other porphyry deposits.  相似文献   

12.
The measured geophysical response of sand – shale sequences is an average over multiple layers when the tool resolution (seismic or well log) is coarser than the scale of sand – shale mixing. Shale can be found within sand – shale sequences as laminations, dispersed in sand pores, as well as load bearing clasts. We present a rock physics framework to model seismic/sonic properties of sub-resolution interbedded shaly sands using the so-called solid and mineral substitution models. This modelling approach stays consistent with the conceptual model of the Thomas–Stieber approach for estimating volumetric properties of shaly sands; thus, this work connects established well log data-based petrophysical workflows with quantitative interpretation of seismic data for modelling hydrocarbon signature in sand – shale sequences. We present applications of the new model to infer thickness of sand – shale lamination (i.e., net to gross) and other volumetric properties using seismic data. Another application of the new approach is fluid substitution in sub-resolution interbedded sand–shale sequences that operate directly at the measurement scale without the need to downscale; such a procedure has many practical advantages over the approach of “first-downscale-and-then-upscale” as it is not very sensitive to errors in estimated sand fraction and end member sand/shale properties and remains stable at small sand/shale fractions.  相似文献   

13.
利用测井资料所获得的基本参数进行岩石物理参数敏感性分析,可以较大提高含烃岩石的识别能力。本文讨论了对地震属性敏感性高的参数的选择及其使用方法,以便提高流体和岩性的识别能力。为了更好的与地震数据解释相结合,我们在敏感性参数空间构造了研究区的岩石物理模板,用以指导实际地震数据定量解释。  相似文献   

14.
To advance and optimize secondary and tertiary oil recovery techniques, it is essential to know the areal propagation and distribution of the injected fluids in the subsurface. We investigate the applicability of controlled‐source electromagnetic methods to monitor fluid movements in a German oilfield (Bockstedt, onshore Northwest Germany) as injected brines (highly saline formation water) have much lower electrical resistivity than the oil within the reservoir. The main focus of this study is on controlled‐source electromagnetic simulations to test the sensitivity of various source–receiver configurations. The background model for the simulations is based on two‐dimensional inversion of magnetotelluric data gathered across the oil field and calibrated with resistivity logs. Three‐dimensional modelling results suggest that controlled‐source electromagnetic methods are sensitive to resistivity changes at reservoir depths, but the effect is difficult to resolve with surface measurements only. Resolution increases significantly if sensors or transmitters can be placed in observation wells closer to the reservoir. In particular, observation of the vertical electric field component in shallow boreholes and/or use of source configurations consisting of combinations of vertical and horizontal dipoles are promising. Preliminary results from a borehole‐to‐surface controlled‐source electromagnetic field survey carried out in spring 2014 are in good agreement with the modelling studies.  相似文献   

15.
A towed streamer electromagnetic system capable of simultaneous seismic and electromagnetic data acquisition has recently been developed and tested in the North Sea. We introduce a 3D inversion methodology for towed streamer electromagnetic data that includes a moving sensitivity domain. Our implementation is based on the 3D integral equation method for computing responses and Fréchet derivatives and uses the re‐weighted regularized conjugate gradient method for minimizing the objective functional with focusing regularization. We present two model studies relevant to hydrocarbon exploration in the North Sea. First, we demonstrate the ability of a towed electromagnetic system to detect and characterize the Harding field, a medium‐sized North Sea hydrocarbon target. We compare our 3D inversion of towed streamer electromagnetic data with 3D inversion of conventional marine controlled‐source electromagnetic data and observe few differences between the recovered models. Second, we demonstrate the ability of a towed streamer electromagnetic system to detect and characterize the Peon discovery, which is representative of an infrastructure‐led shallow gas play in the North Sea. We also present an actual case study for the 3D inversion of towed streamer electromagnetic data from the Troll field in the North Sea and demonstrate our ability to image all the Troll West Oil and Gas Provinces and the Troll East Gas Province. We conclude that 3D inversion of data from the current generation of towed streamer electromagnetic systems can adequately recover hydrocarbon‐bearing formations to depths of approximately 2 km. We note that by obviating the need for ocean‐bottom receivers, the towed streamer electromagnetic system enables electromagnetic data to be acquired over very large areas in frontier and mature basins for higher acquisition rates and relatively lower cost than conventional marine controlled‐source electromagnetic methods.  相似文献   

16.
We develop a semi‐empirical model which combines the theoretical model of Xu and White and the empirical formula of Han, Nur and Morgan in sand–clay environments. This new model may be used for petrophysical interpretation of P‐ and S‐wave velocities. In particular, we are able to obtain an independent estimation of aspect ratios based on log data and seismic velocity, and also the relationship between velocities and other reservoir parameters (e.g. porosity and clay content), thus providing a prediction of shear‐wave velocity. To achieve this, we first use Kuster and Toksöz's theory to derive bulk and shear moduli in a sand–clay mixture. Secondly, Xu and White's model is combined with an artificial neural network to invert the depth‐dependent variation of pore aspect ratios. Finally these aspect ratio results are linked to the empirical formula of Han, Nur and Morgan, using a multiple regression algorithm for petrophysical interpretation. Tests on field data from a North Sea reservoir show that this semi‐empirical model provides simple but satisfactory results for the prediction of shear‐wave velocities and the estimation of reservoir parameters.  相似文献   

17.
The accurate estimation of sub‐seafloor resistivity features from marine controlled source electromagnetic data using inverse modelling is hindered due to the limitations of the inversion routines. The most commonly used one‐dimensional inversion techniques for resolving subsurface resistivity structures are gradient‐based methods, namely Occam and Marquardt. The first approach relies on the smoothness of the model and is recommended when there are no sharp resistivity boundaries. The Marquardt routine is relevant for many electromagnetic applications with sharp resistivity contrasts but subject to the appropriate choice of a starting model. In this paper, we explore the ability of different 1D inversion schemes to derive sub‐seafloor resistivity structures from time domain marine controlled source electromagnetic data measured along an 8‐km‐long profile in the German North Sea. Seismic reflection data reveal a dipping shallow amplitude anomaly that was the target of the controleld source electromagnetic survey. We tested four inversion schemes to find suitable starting models for the final Marquardt inversion. In this respect, as a first scenario, Occam inversion results are considered a starting model for the subsequent Marquardt inversion (Occam–Marquardt). As a second scenario, we employ a global method called Differential Evolution Adaptive Metropolis and sequentially incorporate it with Marquardt inversion. The third approach corresponds to Marquardt inversion introducing lateral constraints. Finally, we include the lateral constraints in Differential Evolution Adaptive Metropolis optimization, and the results are sequentially utilized by Marquardt inversion. Occam–Marquardt may provide accurate estimation of the subsurface features, but it is dependent on the appropriate conversion of different multi‐layered Occam model to an acceptable starting model for Marquardt inversion, which is not straightforward. Employing parameter spaces, the Differential Evolution Adaptive Metropolis approach can be pertinent to determine Marquardt a priori information; nevertheless, the uncertainties in Differential Evolution Adaptive Metropolis optimization will introduce some inaccuracies in Marquardt inversion results. Laterally constrained Marquardt may be promising to resolve sub‐seafloor features, but it is not stable if there are significant lateral changes of the sub‐seafloor structure due to the dependence of the method to the starting model. Including the lateral constraints in Differential Evolution Adaptive Metropolis approach allows for faster convergence of the routine with consistent results, furnishing more accurate estimation of a priori models for the subsequent Marquardt inversion.  相似文献   

18.
In this paper we present a case history of seismic reservoir characterization where we estimate the probability of facies from seismic data and simulate a set of reservoir models honouring seismically‐derived probabilistic information. In appraisal and development phases, seismic data have a key role in reservoir characterization and static reservoir modelling, as in most of the cases seismic data are the only information available far away from the wells. However seismic data do not provide any direct measurements of reservoir properties, which have then to be estimated as a solution of a joint inverse problem. For this reason, we show the application of a complete workflow for static reservoir modelling where seismic data are integrated to derive probability volumes of facies and reservoir properties to condition reservoir geostatistical simulations. The studied case is a clastic reservoir in the Barents Sea, where a complete data set of well logs from five wells and a set of partial‐stacked seismic data are available. The multi‐property workflow is based on seismic inversion, petrophysics and rock physics modelling. In particular, log‐facies are defined on the basis of sedimentological information, petrophysical properties and also their elastic response. The link between petrophysical and elastic attributes is preserved by introducing a rock‐physics model in the inversion methodology. Finally, the uncertainty in the reservoir model is represented by multiple geostatistical realizations. The main result of this workflow is a set of facies realizations and associated rock properties that honour, within a fixed tolerance, seismic and well log data and assess the uncertainty associated with reservoir modelling.  相似文献   

19.
Expanding the frequency spectrum in marine CSEM applications   总被引：1，自引：0，他引：1  
In this paper we show how marine controlled source electromagnetic data interpretation can be improved if the data are acquired with an expanded frequency spectrum. Especially in the case of targets located at a wide range of depths, both high- and low-frequency data can provide useful information for improving the risk analysis associated with different prospects with variable size and depth. We discuss an application to a real data set acquired in deep water offshore Nigeria using two values of fundamental frequency: 0.05 Hz and 0.25 Hz. Both frequencies, together with higher frequency harmonics, have been used for multi-frequency and multi-dimensional modelling and inversion with excellent results.
At the end of the interpretation work, areas with different electric and magnetic anomalies were mapped and quantitatively interpreted in terms of resistivity distribution in the 3D space. Relatively high-frequency data (0.25 Hz and the first two harmonics) were useful for constraining the shallowest part of the resistivity models, including the presence of thin resistive layers, such as the gas sand recognized in correspondence of the well previously drilled in the NW portion of the block.
Low-frequency data (0.05 Hz) were useful for constraining the deepest portion of the models (from 2 km to 4 km below sea floor) and for characterizing the resistivity of the background.
From an exploration point of view, the whole workflow based on multi-frequency data analysis of this electromagnetic data set was very useful for further de-risking the different prospects previously individuated in the area using seismic information.  相似文献   

20.
Due to the complicated geophysical character of tight gas sands in the Sulige gasfield of China, conventional surface seismic has faced great challenges in reservoir delineation. In order to improve this situation, a large‐scale 3D‐3C vertical seismic profiling (VSP) survey (more than 15 000 shots) was conducted simultaneously with 3D‐3C surface seismic data acquisition in this area in 2005. This paper presents a case study on the delineation of tight gas sands by use of multi‐component 3D VSP technology. Two imaging volumes (PP compressional wave; PSv converted wave) were generated with 3D‐3C VSP data processing. By comparison, the dominant frequencies of the 3D VSP images were 10–15 Hz higher than that of surface seismic images. Delineation of the tight gas sands is achieved by using the multi‐component information in the VSP data leading to reduce uncertainties in data interpretation. We performed a routine data interpretation on these images and developed a new attribute titled ‘Centroid Frequency Ratio of PSv and PP Waves’ for indication of the tight gas sands. The results demonstrated that the new attribute was sensitive to this type of reservoir. By combining geologic, drilling and log data, a comprehensive evaluation based on the 3D VSP data was conducted and a new well location for drilling was proposed. The major results in this paper tell us that successful application of 3D‐3C VSP technologies are only accomplished through a synthesis of many disciplines. We need detailed analysis to evaluate each step in planning, acquisition, processing and interpretation to achieve our objectives. High resolution, successful processing of multi‐component information, combination of PP and PSv volumes to extract useful attributes, receiver depth information and offset/ azimuth‐dependent anisotropy in the 3D VSP data are the major accomplishments derived from our attention to detail in the above steps.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号