共查询到20条相似文献，搜索用时 31 毫秒
1.
Eroded sediment may have significant effects on the hydraulics of overland flow, but few studies have been performed to quantify these effects on steep slopes. This study investigated the potential effects of sediment load on Reynolds number, Froude number, flow depth, mean velocity, Darcy–Weisbach friction coefficient, shear stress, stream power, and unit stream power of overland flow in a sand‐glued hydraulic flume under a wide range of hydraulic conditions and sediment loads. Slope gradients were varied from 8·7 to 34·2%, unit flow rates from 0·66 to 5·26×10?3 m2 s?1, and sediment loads from 0 to 6·95 kg m?1 s?1. Both Reynolds number (Re) and Froude number (Fr) decreased as sediment load increased, implying a decrease in flow turbulence. This inverse relationship should be considered in modeling soil erosion processes. Flow depth increased as sediment load increased with a mean value of 1·227 mm, caused by an increase in volume of sediment‐laden flow (contribution 62·4%) and a decrease in mean flow velocity (contribution 37·6%). The mean flow velocity decreased by up to 0·071 m s?1 as sediment load increased. The Darcy–Weisbach friction coefficient (f) increased with sediment load, showing that the total energy consumption increased with sediment load. The effects of sediment load on f depended on flow discharge: as flow discharge increased, the influence of sediment load on f decreased due to increased flow depth and reduced relative roughness. Flow shear stress and stream power increased with sediment load, on average, by 80·5% and 60·2%, respectively; however, unit stream power decreased by an average of 11·1% as sediment load increased. Further studies are needed to extend and apply the insights obtained under these controlled conditions to real‐world overland flow conditions. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
2.
Surface flow and suspended sediment discharge from the head hollow of the Jozankei Experimental Watershed in Hokkaido, northern Japan, were measured to clarify the implications of subsurface hydrology for soil movement. Subsurface discharges during the extremely large storms of 1993 to 1994 were measured in a V-notch weir installed at a natural spring near the bottom of the head hollow, and shallow groundwater levels were observed in the wells excavated in the hollow. Sediment samples whose particle size range from 0·001 to 0·1 mm were manually and automatically collected at 15 to 60 min intervals, by use of 1 or 21 polyethylene bottles. Maximum concentration and flux of suspended sediment during the storms preceded the peak discharge of subsurface flow by several hours. Neither the changes in concentration (mg l−1) nor flux (mg s−1) of suspended sediment coincided with those in subsurface discharge (l s−1). Furthermore, sediment concentration was poorly correlated with the rate of change in subsurface discharge (l s−2) during the rising limb of the hydrograph. Suspended sediment flux during the acceleratory limb, however, was closely correlated with the rate of change in subsurface discharge. The relationship between suspended sediment flux and rate of change in subsurface discharge were in inverse proportion to initial subsurface discharge before the storm runoff and they represented rare seasonal variation. Subsurface hydraulic erosion and transport of suspended sediment resulting from changes in rate of change in subsurface discharge actively occur during the acceleratory rising limb of the hydrograph. Accordingly, subsurface hydraulic erosion during the acceleratory rising limb of the hydrograph can be physically understood by analysing suspended sediment flux associated with rate of change in subsurface discharge and initial subsurface discharge. © 1997 John Wiley & Sons, Ltd. 相似文献
3.
Motivated by field studies of the Ems estuary which show longitudinal gradients in bottom sediment concentration as high as O(0.01 kg/m4), we develop an analytical model for estuarine residual circulation based on currents from salinity gradients, turbidity gradients, and freshwater discharge. Salinity is assumed to be vertically well mixed, while the vertical concentration profile is assumed to result from a balance between a constant settling velocity and turbulent diffusive flux. Width and depth of the model estuary are held constant. Model results show that turbidity gradients enhance tidally averaged circulation upstream of the estuarine turbidity maximum (ETM), but significantly reduce residual circulation downstream, where salinity and turbidity gradients oppose each other. We apply the condition of morphodynamic equilibrium (vanishing sediment transport) and develop an analytical solution for the position of the turbidity maximum and the distribution of suspended sediment concentration (SSC) along a longitudinal axis. A sensitivity study shows great variability in the longitudinal distribution of suspended sediment with the applied salinity gradient and six model parameters: settling velocity, vertical mixing, horizontal dispersion, total sediment supply, fresh water flow, and water depth. Increasing depth and settling velocity move the ETM upstream, while increasing freshwater discharge and vertical mixing move the ETM downstream. Moreover, the longitudinal distribution of SSC is inherently asymmetric around the ETM, and depends on spatial variations in the residual current structure and the vertical profile of SSC. 相似文献
4.
《国际泥沙研究》2022,37(5):619-638
The large confluence between the Yangtze River and the outflow channel of Poyang Lake is receiving attention due to its importance in flood control and ecological protection in the Yangtze River basin. There is a large floodplain along the outflow channel of Poyang Lake, which is submerged during high flow and dry during low flow. The effects of the submergence of this floodplain on sediment and morphological characteristics at this large confluence have not been known. Hence, a field investigation was done in March 2019 (relatively high flow, Survey 3) to complement the previous field studies done in August (high flow, Survey 1) and December 2018 (low flow, Survey 2) to identify the temporal variations of sediment and morphological characteristics considering the submergence of this large floodplain. The predominant sediment transport modes were wash load for Poyang Lake and confluence particles and mixed bedload/suspended load for the Yangtze River particles. The sediment transport processes were largely affected by both the secondary flows and the water density contrast between the tributaries with a lock-exchange sediment rich, denser flow moving across the inclined mixing interface in Surveys 1 and 2. The sediment flux across the mixing interface was weakened in Survey 3 when the density contrast was very small. The stagnation zone near the confluence apex had a low sediment concentration and played a role in preventing the sediment flux exchange between the two flows, and its size, and, thus, its importance as a barrier to sediment mixing were related to the submergence of the floodplain. The bed morphology with the local scour holes at the confluence was largely affected by the large-size helical cells, and this kind of effect was weakened as the secondary flows got restricted in Survey 3. The current results expand the database and knowledge on the sediment transport and morphological features of large river confluences. 相似文献
5.
Vegetation stems and litter cover have different effects on sediment transport capacity under the same experimental conditions, which in essence, may be due to differences in their hydraulic properties, but the availability of comparative studies is limited. This study aimed to compare the hydraulic properties affected by litter and stem cover, compare differences in the drag forces exerted by litter and stems on overland flow, and develop new Manning's n and flow velocity equations for litter cover. Two series of flume experiments were conducted with the same slope gradients (8.8%, 17.6%, 26.8%) and flow discharge rates (0.5, 1.0 × 10−3 m3 s−1). Artificial Gramineae stems with a 0%–30% cover level and Pinus tabulaeformis litter with a 0%–70% cover level were used in series 1 and series 2, respectively. The flow velocity and depth were measured. The results showed that the Froude number and flow velocity affected by stem cover were much lower than those affected by litter cover, while the opposite trend was observed in the relative magnitude of the Reynolds number, flow depth and shear stress. The form resistance caused by stems was 22–57 times greater than that caused by litter for the same cover level, which suggests that stem cover contributes more than litter cover to increasing the flow resistance and reducing the flow's ability for sediment detachment and transport. Two new equations for calculating Manning's n and flow velocity under the influence of litter cover were developed, with R2 and NSE values of 0.96. The results of this study contribute to revealing the mechanisms of the differences of the effects of stem and litter cover on soil erosion. 相似文献
6.
Qianhua Shi Wenlong Wang Mingming Guo Zhuoxin Chen Lanqian Feng Man Zhao Hai Xiao 《水文研究》2020,34(3):718-729
Headcut erosion is associated with major hydraulic changes induced by the gully head of concentrated flow. However, the variation in the hydraulic characteristics of the headcut erosion process is still not clear in the gully region of the Loess Plateau. A series of rainfall combined scouring experiments (flow discharges ranging from 3.6 to 7.2 m3 hr−1, with 0.8 mm min−1 rainfall intensity) were conducted on experimental plots to clarify the variation in the hydraulic parameters induced by gully head and erosion processes under different flow discharges. The results showed that concentrated flows in the catchment area and gully bed were turbulent (Reynolds number ranging from 1,876 to 6,693) and transformed between supercritical and subcritical (Froude number ranging from 0.96 to 3.73). The hydraulic parameters, such as the flow velocity, Reynolds number, shear stress, stream power, Darcy–Weisbach friction factor, and unit stream power in the catchment area were 0.45–0.59 m s−1, 2086–6693, 1.96–5.33 Pa, 0.89–2.86 W m−2, 0.08–0.16, and 0.023–0.031 m s−1, respectively. When the concentrated flows dropped from the gully head, the hydraulic parameters in the gully bed decreased by 3.39–26.07%, 1.49–29.99%, 65.19–67.14%, 67.25–74.96%, 28.53–61.31%, and 67.82–77.14%, respectively, which contributed to the flow energy consumption at the gully head. As flow discharge increased, Reynolds number, shear stress, and stream power increased, while flow velocity, Froude number, unit stream power, and Darcy–Weisbach friction factor did not. The flow energy consumption at the gully head was 9.66–10.13, 13.25–13.74, 15.68–16.41, and 19.28–20.25 J s−1, respectively, under different flow discharges and accounted for 60.58–68.50% of the flow energy consumption of the experimental plots. Generally, the sediment discharges increased rapidly at the initial stage, then increased slowly, and finally reached a steady state condition, which showed a significant declining logarithmic trend with experimental duration (P<.01) and increased with increasing flow discharge. Accordingly, the flow energy consumption was significantly correlated with the sediment yield. These findings could improve our understanding of the hydraulic properties and flow energy characteristics of headcut erosion. 相似文献
7.
Water flow velocity is an important hydraulic variable in hydrological and soil erosion models, and is greatly affected by freezing and thawing of the surface soil layer in cold high-altitude regions. The accurate measurement of rill flow velocity when impacted by the thawing process is critical to simulate runoff and sediment transport processes. In this study, an electrolyte tracer modelling method was used to measure rill flow velocity along a meadow soil slope at different thaw depths under simulated rainfall. Rill flow velocity was measured using four thawed soil depths (0, 1, 2 and 10 cm), four slope gradients (5°, 10°, 15° and 20°) and four rainfall intensities (30, 60, 90 and 120 mm·h−1). The results showed that the increase in thawed soil depth caused a decrease in rill flow velocity, whereby the rate of this decrease was also diminishing. Whilst the rill flow velocity was positively correlated with slope gradient and rainfall intensity, the response of rill flow velocity to these influencing factors varied with thawed soil depth. The mechanism by which thawed soil depth influenced rill flow velocity was attributed to the consumption of runoff energy, slope surface roughness, and the headcut effect. Rill flow velocity was modelled by thawed soil depth, slope gradient and rainfall intensity using an empirical function. This function predicted values that were in good agreement with the measured data. These results provide the foundation for a better understanding of the effect of thawed soil depth on slope hydrology, erosion and the parameterization scheme for hydrological and soil erosion models. 相似文献
8.
Chendi Zhang Mengzhen Xu Marwan A. Hassan Shawn M. Chartrand Zhaoyin Wang Zewei Ma 《地球表面变化过程与地形》2020,45(2):280-294
Exceptional flood events with a return period of about 50 years can be destructive to step-pool channel segments. However, field investigations and flume experiments have not examined the hydraulic and morphological feedbacks of step-pool morphology during unsteady hydrographs of exceptional flood events. We performed a series of flume experiments with a manually constructed step model, perturbed with three hydrographs that varied in the rate of water supply change. The bed texture, topography, flow regimes, surface flow field and water depth were characterized and measured as the flow rate was increased during the experiments. A distinct pool feature emerged downstream of the manually constructed step when the flow rate exceeded the threshold scaled to the peaks of ordinary flood events in well-graded mountain streams. The pool feature was modified in several different ways with flow rate increase. The bed surface steadily coarsened, micro-bedforms developed and became more pronounced, the bed topography became more spatially complex based on analysis using the Hurst exponent, and last, pool depth steadily increased. Pool modification was also linked to the flow regime: the impinging jet regime led to grain size segmentation in the pool while the jump regime contributed to decelerating flow velocity. The steeper rising limb of hydrograph led to a less developed pool feature, with smaller sized micro-bedforms in the pool bottom to outlet, and higher discharge threshold for distinct coarsening and scouring in the pool. The estimated energy dissipation within the step-pool unit decreased as a power function from low to high flow, quantified as the ratio hc/HS, where hc is the critical water depth and HS is scour depth. Our results highlight the interaction between morphology, hydraulics, and energy dissipation of step-pool unit and the crucial role of hydrograph shape on the interaction during flow increase © 2019 John Wiley & Sons, Ltd. 相似文献
9.
Suspended sediment is a major source of pollution in irrigation‐dominated watersheds. However, little is known about the process and mechanisms of suspended sediment transport in drain channels directly connected to agricultural fields. This paper explains sediment dynamics using averaged 5 min flow discharge Q (m3 s?1) and suspended sediment concentration C (mg l?1) collected during one crop season in a small catchment containing a first‐order drain channel and its connected six agricultural fields within the Salton Sea watershed. The statistical properties and average trends of Q and C were investigated for both early (i.e. November) and late (i.e. January) stages of a crop season. Further in‐depth analysis on sediment dynamics was performed by selecting two typical single‐field irrigation events and two multiple‐field irrigation events. For each set of irrigation events, the process of suspended sediment transport was revealed by examining hydrograph and sediment graph responses. The mechanisms underlying suspended sediment transport were investigated by analysing the types of corresponding hysteresis loop. Finally, sediment rating curves for both hourly and daily data at early and late stages and for the entire crop season were established to seek possible sediment‐transport predictive model(s). The study suggests that the complicated processes of suspended sediment transport in irrigation‐dominated watersheds require stochastic rather than deterministic forecasting. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
10.
Wave-induced, steep vortex ripples are ubiquitous features in shallow coastal seas and it is therefore important to fully understand and model the sediment transport processes that occur over them. To this end, two two-dimensional vertical (2DV) models have been critically tested against detailed velocity and sediment concentration measurements above mobile ripples in regular asymmetric oscillatory flow. The two models are a k–ω turbulence-closure model and a discrete-vortex, particle-tracking (DVPT) model, while the data are obtained in the Aberdeen oscillatory flow tunnel (AOFT). The models and the data demonstrate that the time-dependent velocity and suspended sediment concentration above the ripple are dominated by the generation of lee-side vortices and their subsequent ejection at flow reversal. The DVPT model predicts the positions and strengths of the vortices reasonably well, but tends to overpredict the velocity close to the ripple surface. The k–ω model, on the other hand, underpredicts the height to which the vortices are lifted, but is better able to predict the velocity close to the bed. In terms of the cycle- and ripple-averaged horizontal velocity, both models are able to reproduce the observed offshore flow close to and below the ripple crest and the DVPT model is able to produce the onshore flow higher up. In the vicinity of the vortices, the DVPT model better represents the concentration (because of its better prediction of vorticity). The k–ω model, on the other hand, better represents the concentration close to the ripple surface and higher up in the flow (because of the better representation of the near-bed flow and background turbulence). The measured and predicted cycle- and ripple-averaged suspended sediment concentrations are in reasonable agreement and demonstrate the expected region of exponential decay. The models are able to reproduce the observed offshore cycle- and ripple-averaged suspended sediment flux from the ripple troughs upwards, and as a result, produce net offshore suspended sediment transport rates that are in reasonable agreement. The net measured offshore suspended transport rate, based on the integration of fluxes, was found to be consistent with the total net offshore transport measured in the tunnel as a whole once the onshore transport resulting from ripple migration was taken into account, as would be expected. This demonstrates the importance of models being able to predict ripple-migration rates. However, at present neither of the models is able to do so. 相似文献
11.
The objective of this case study was to calibrate and verify detailed transport model of sediment in a 4‐kilometre stretch of the middle Elbe floodplains in Germany. The hydraulic RMA‐2 model and the SED2d‐WES sediment transport model were used. These models were calibrated and validated by detailed measurement of the surface water elevations, the velocities at six profiles, and the suspended sediment concentration and deposition (by means of 10 sediment traps). The flow was modelled for three steady‐state discharges. The surface water elevations were calculated to an accuracy of less than 5 cm compared to measurements. The differences between the calculated and measured velocities were with one exception smaller than 0.2 m/s (measured range 0.1…?1.0 m/s). An average sediment input of 35 g/(m2 d) was calculated for the flood event studied. The highest calculated sedimentation rates of 700 g/(m2 d) (dry density 90 kg/m3) occurred in quiescent zones and abandoned channels. Twenty‐five percent of the deposited sediment settled in the quiescent zones (which only account for 13% of the area). The most sensitive parameters of the sediment transport model were the settling velocity and critical shear stress. The modelling techniques used allowed sediment deposition on the floodplains of the Elbe to be realistically depicted. 相似文献
12.
Flume experiments were conducted in order to monitor changes in flow turbulence intensity and suspended sediment concentration at seven stages across the ripple–dune transition and at three different positions above the bed surface. Three‐dimensional velocity measurements were obtained using an acoustic Doppler velocimeter (ADV). Suspended sediment concentration (SSC) was monitored indirectly using ADV signal amplitude. Although limited to time‐averaged parameters, the analysis reveals that SSC varies significantly with stage across the transition and with sampling height. The statistical analysis also reveals an apparent uniformity of suspended sediment concentration with height above the bed in the lower half of the flow depth at the critical stage in the transition from ripples to dunes. This is also the stage at which turbulence intensity is maximized. Statistically significant correlations were also observed between suspended sediment concentrations and root‐mean‐square values of vertical velocity fluctuations. These correlations reflect the various levels of shear‐layer activity and the distinct turbulent flow regions across the transition. Conversely, time‐averaged values of Reynolds shear stress exhibit a very weak relationship with suspended sediment concentrations. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
13.
Saltmarsh vegetation significantly influences tidal currents and sediment deposition by decelerating the water velocity in the canopy. In order to complement previous field results, detailed profiles of velocity and turbulence were measured in a laboratory flume. Natural Spartina anglica plants were installed in a 3 m length test section in a straight, recirculating flume. Different vegetation densities, water depths and surface velocities were investigated. The logarithmic velocity profile, which existed in front of the vegetation, was altered gradually to a skimming-flow profile, typical for submerged saltmarsh vegetation. The flow reduction in the denser part of the canopy also induced an upward flow (the current was partially deflected by the canopy). The skimming flow was accompanied by a zone of high turbulence co-located with the strongest velocity gradient. This gradient moved upward and the turbulence increased with distance from the edge of the vegetation. Below the skimming flow, the velocity and the turbulence were low. The structure of the flow in the canopy was relatively stable 2 m into the vegetation. The roughness length (z0) of the vegetation depends only on the vegetation characteristics, and is not sensitive to the current velocity or the water depth. Both the reduced turbulence in the dense canopy and the high turbulence at the top of the canopy should increase sediment deposition. On the other hand, the high turbulence zone just beyond the vegetation edge and the oblique upward flow may produce reduced sedimentation; a phenomenon that was observed near the vegetation edge in the field. 相似文献
14.
Hubert Chanson 《地球表面变化过程与地形》2011,36(2):180-189
In an open channel, a sudden rise in water level induces a positive surge, or bore, that may develop as a hydraulic jump in translation. When the surge propagates against an adverse slope, it decelerates until it becomes a stationary hydraulic jump. Both hydraulic jumps and decelerating surges induce some intense turbulent mixing and have some major impact on the sediment transport in natural systems. Herein, a physical investigation was conducted in a relatively large rectangular channel. Hydraulic jumps and surges were generated by the rapid closure of a gate at the channel downstream end. The turbulent shear stresses were measured with high temporal and spatial resolution (200 Hz sampling rate) in the jump flow. A comparison between the stationary hydraulic jump, hydraulic jump in translation and decelerating surge measurements showed some marked differences in terms of turbulent mixing. The results highlighted some intense mixing beneath the jump front and roller for all configurations. The levels of turbulent stresses were one to two orders of magnitude larger than a critical threshold for sediment motion. The findings provide some insights into the hydraulic jump migration processes in mobile bed channels, and the complex transformation from a moving jump into a stationary jump. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
15.
This paper illustrates how the acoustic Doppler current profiler （ADCP） and single-beam echo-sounder （SBES） recordings can be used for the calibration of existing software to assist in generalizing the morphodynamic processes in large rivers at key sites such as bifi.trcations and confluences. Calibration of the MIKE21C numerical model by the Danish Hydraulic Institute at the 25-km-long reach of Lower Paran~ near Rosario （Argentina） is presented. This reach includes two downstream confluences and two bifurcations. The model simulates a 2-D depth-averaged flow velocity and the related sediment fluxes to predict the bifurcation morphodynamics that affects the Paranh waterway. To investigate the river channel bathymetry, roughness, flow discharge allocation at bifurcations, suspended sediment concentration and grain size distributions, several instruments were used. These instruments included two ADCPs by Teledyne RDI working at frequencies of 600 and 1,200 kHz, a Sontek ADCP working at a frequency of 1,000 kHz and a SBES. The method to assess suspended sediment concentration and grain size distributions has been previously described. This paper focuses primarily on investigating dune morphology （by means of SBES depth measurements） and friction velocity （by means of ADCP profiling） to determine the river channel bed-roughness. The 2-D model results agree with observed values of bed-roughness, flow velocity and suspended sediment concentration distributions at the investigated sections, known data of water slope and total load of bed sediment are in good agreement with model results. 相似文献
16.
Grain-size distributions of suspended load over a sand-gravel bed at two different flow velocities were studied in a laboratory flume.The experiments had been performed to study the influence of flow velocity and suspension height on grain-size distribution in suspension over a sand-gravel bed.The experimental findings show that with an increase of flow velocity,the grain-size distribution of suspended load changed from a skewed form to a bimodal one at higher suspension heights.This study focuses on the determination of the parameter β_n which is the ratio of the sediment diffusion coefficient to the momentum diffusion coefficient of n th grain-size.A new relationship has been proposed involving β_n,the normalizing settling velocity of sediment particles and suspension height,which is applicable for widest range of normalizing settling velocity available in literature so far.A similar parameter β for calculating total suspension concentration is also developed.The classical Rouse equation is modified with β_n and β and used to compute grain-size distribution and total concentration in suspension,respectively.The computed values have shown good agreement with the measured values of experimental data. 相似文献
17.
Suspended sediment is conventionally regarded as that sediment transported by a fluid that it is fine enough for turbulent eddies to outweigh settling of the particles through the fluid. Early work in the fluvial field attributed suspension to turbulence, and led to the notion of a critical threshold for maintaining sediment in suspension. However, research on both turbulence structures and the interactions between suspended sediment and bedforms in rivers has shown a more complex story and, although there appear to have been no studies of the impact of bedforms on aeolian suspended sediment concentrations, turbulent flow structures and transport rates of saltating particles have been shown to be affected. This research indicates that suspended sediment neither travels with the same velocity as the flow in which it is suspended, nor is it likely to remain in suspension in perpetuity, even under conditions of steady flow or in unsteady flow the where dimensionless critical threshold is permanently exceeded. Rather, like bedload, it travels in a series of hops, and is repeatedly deposited on the bed where it remains until it is re‐entrained. Is there, therefore, a qualitative difference between suspended and saltating sediment, or is it just a quantitative difference in the size of the jump length and the frequency of re‐entrainment? It is our contention that the distinction of suspension as a separate class of sediment transport is both arbitrary and an unhelpful anthropocentric artefact. If we recognize that sediment transport is a continuum and applies to any fluid medium rather than split into different “processes” based on arbitrary thresholds and fluids, then recognizing the continuity will enable development of an holistic approach sediment transport, and thus sediment‐transport models that are likely to be viable across a wider range of conditions than hitherto. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
18.
ABSTRACTThe presence of aquatic vegetation in riverine and lacustrine environments alters the mean and turbulent flow structure and thus impacts the fate and transport of sediment and contaminants. Turbulent flows through Vallisneria natans (V. natans) and Potamogeton malaianus (P. malaianus) were investigated in a laboratory flume. The impact of plant morphology on mean velocity profile and turbulence distribution was analysed and discrepancies in flow alteration caused by different types of macrophyte were highlighted. Results show that a dense canopy of submerged macrophyte leads to a velocity profile featuring a counter velocity gradient in the lower part of the canopy. Negative Reynolds stress and its local maximum were observed there. Discrepancies in flow structure caused by different morphologies of both tested plants were further identified. With smaller frontal area in the lower part of the canopy, P. malaianus causes a much bigger gradient and local maximum in the velocity profile, and thus a larger local stress maximum than V. natans. The mean velocity gradient around the top of canopy, the Reynolds stress and the turbulence kinetic energy at the canopy interface are smaller than for the flow through the V. natans canopy. Larger reduction of the mean velocity within the V. natans canopy makes the suspended sediment of fine particles more easily deposited than in the P. malaianus canopy. 相似文献
19.
Carmelo Conesa-García José Luis Sánchez-Tudela Pedro Pérez-Cutillas Francisco Martínez-Capel 《水文科学杂志》2018,63(1):114-135
This study focuses on the spatial variations in vegetative roughness associated with morphological channel adjustments due to the presence of check dams in Mediterranean torrential streams. Manning’s n values were estimated using methods established by previous studies of submerged and non-submerged vegetation in laboratory flume experiments and field work. The results showed a linear decrease in shrub density and rate of variation of the roughness coefficient versus degree of submergence with increasing distance upstream from the check dam, while downstream, the filling of the check dam and the bed incision had the most influence. A regression analysis was applied by fitting the data to different models: relationships between Manning’s n and the flow velocity were found to be of the power type for shrubs in all upstream sections, while relationships of flow velocity versus hydraulic radius in the sections closest to check dams showed a good fit to second-order polynomial equations. 相似文献
20.
Hugh G. Smith 《水文研究》2008,22(16):3135-3148
Historically upland headwater catchments in south‐eastern Australia have undergone extensive gully erosion that has removed large amounts of sediment to lowlands. Recent research suggests these upland areas may continue to dominate fine sediment loads in lowland rivers. Improved understanding of sediment transfer through upland headwater catchments may have implications for interpreting downstream sediment supply. In this study a nested catchment design was utilized to examine suspended sediment yields and delivery from a small tributary sub‐catchment (1·64 km2) to the study catchment outlet (53·5 km2). Monitoring of suspended sediment concentration and discharge was undertaken for a period of nearly two years and used to estimate suspended sediment loads. Estimated total suspended sediment exports over the period of monitoring were 24·16 t from the sub‐catchment and 550·3 t from the catchment, which are generally less than previous reported small catchment yields in south‐eastern Australia. The extent of sediment delivery was examined using between‐site ratios of specific sediment yield per unit area and incised channel length. Sediment delivery was high under average rainfall conditions, but seasonally dependent. Both suspended sediment yields and the extent of delivery peaked over spring months, supplemented by remobilization of sediment stored during summer months in the main catchment channel. The findings of this study suggest much of the suspended sediment exported from small incised upland sub‐catchments (1–2 km2) may be delivered to downstream reaches under average rainfall conditions, which, in conjunction with the findings of previous research supports the potential importance of contributions from these areas to suspended sediment loads in lowland rivers during high flow periods. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献