共查询到20条相似文献，搜索用时 31 毫秒
1.
A new integrated suspended sediment monitoring strategy applying direct and indirect technologies is presented.Optical sensors continuously record the turbidity at one point in the channel cross section close to the river bank and are calibrated by water samples taken close to the sensor.Additionally measurements are performed to establish the distribution of suspended sediment in a cross section（bottle samples combined with acoustic devices）.Using correction factors（probe and cross-sectional factor） these monitoring methods are combined and it is,thus,possible to fully document the temporal and spatial variability of the suspended sediment transport and to estimate the suspended sediment load for certain time periods.This monitoring strategy was implemented at various measurement sites in Austria as well as at the Hainburg Road Bridge site on the Danube River.It has already been successfully applied for three years at this measurement site and suspended sediment loads during high discharges up to a 15 year flood event have been monitored.To evaluate the new monitoring methods the results were compared with load estimation methods found in the literature including averaging and ratio estimators as well as rating curves.The results prove that with the new methodology,the temporal variability of the suspended sediment transport can be detected more accurately compared with the other methods.They also demonstrate that the additional consideration of the spatial distribution of the suspended sediment concentration in the cross section is crucial as the mean concentration in the cross section can significantly exceed the concentration near the banks,especially at large rivers like the Danube River. 相似文献
2.
Relationship between bed shear stress and suspended sediment concentration:annular flume experiments
In this study,annular flume experiments were carried out,using the sediment samples collected from the lower part of the inter-tidal zone at Xiaoyangkou,Jiangsu coast,China.The Ariathurai-Partheniades equation was used to determine the bed shear stress,by evaluating variations in the suspended sediment concentration within the water column.The derived relation between the bed shear stress and suspended sediment concentration shows that,at various stages of seabed erosion, suspended sediment concentration increases rapidly when the flow velocity is increased,but the pattern of change in the bed shear stress does not follow suit.At low concentrations,bed shear stress initially increases markedly with increasing flow velocity.However,when the concentration reaches an apparently critical level around 0.55 kg m"3,the rate of change in the bed shear stress abruptly slows down,or becomes almost constant,in response to further increases in the flow velocity.Results of experiments indicate that,from a critical level onward,suspended sediment concentration has a strong influence on the bed shear stress. 相似文献
3.
Haoming FAN Qiangguo CAI Chengjiu GUO Tieliang WANG 《国际泥沙研究》2006,21(3):209-219
1 INTRODUCTION The particle size of sediment eroded from basins can provide basic information about erosion processes (Meyer et al., 1980), which can be divided into sheet wash sediment processes on hill slopes and fluvial sediment processes in rivers. In… 相似文献
4.
A method for collecting suspended sediment samples has been developed that pumps a discharge-weighted volume of water from fixed depths at four to 40 locations across a river and separates the suspended sediment in the sample using a continuous-flow centrifuge. The efficacy of the method is evaluated by comparing the particle size distributions of sediment collected by the discharge-weighted pumping method with the particle size distributions of sediment collected by depth integration and separated by gravitational settling. The pumping method was found to undersample the suspended sand sized particles (> 63 μm) but to collect a representative sample of the suspended silt and clay sized particles (< 63 μm). The centrifuge separated the silt and clay sized particles (< 63 μm) into three fractions. Based on the average results of processing 17 samples from the Mississippi River and several of its large tributaries in 1990, about 10% of the silt and clay sized material was trapped in a centrifuge bowl-bottom sealing unit containing the nozzle and consisted of mostly medium and coarse silt from 16 to 63 μm. About 74% was retained on a Teflon liner in the centrifuge bowl and consisted of sizes from 0–1 to 63 μm. About 9% was discharged from the centrifuge in the effluent and was finer than 0–1 μm. About 7% was lost during the processes of removing the wet sediment fractions from the centrifuge, drying and weighing. The success of the discharge-weighted pumping method depends on how homogeneously the silt and clay sized particles (< 63 μm) are distributed in the vertical direction in the river. The degree of homogeneity depends on the composition and degree of aggregation of the suspended sediment particles. 相似文献
5.
6.
Fine-sediment mineralogy of source rocks and suspended sediment,rother catchment,West Sussex 总被引：1，自引：0，他引：1
Peter A. Wood 《地球表面变化过程与地形》1978,3(3):255-263
The clay and silt mineralogy of the Cretaceous bedrocks of the Rother drainage basin is restricted to seven minerals. The mineralogy of soils and alluvium is similar to the bedrock upon which they are developed although minor variations can be found. The mineralogy of bedrock, soils and alluvium is reflected to some extent in the suspended sediment of rivers draining over them, and three different mineral assemblage zones are identified. Subtle controls of mineralogical variation in suspended sediment may include the ratio of groundwater/surface runoff contribution to river flow, rate of reaction of soil and bedrock to precipitation, preferential settling of non-platy grains in quieter stretches of water, and the precipitation of material from solution as waters equilibriate with the atmosphere. 相似文献
7.
A system has been installed to automatically monitor rainfall, streamflow, bedload discharge and suspended sediment concentration in the arid to hyper‐arid setting of Nahal Rahaf, Southern Judean Desert in Israel. The Rahaf gauging station is located in a relatively steep, wide channel with an unsteady bed driven by flash floods. It is an attempt to deploy modern automatic equipment for continuous sediment transport monitoring in harsh, arid fluvial environments. Unit bedload discharges are the highest recorded hitherto, suggesting they may represent an upper end member in the worldwide climate–bedload discharge relationship. Suspended sediment concentration is much higher than is typical of perennial fluvial humid environments. There is high correlation between suspended sediment concentration and water discharge on an event scale, with diverse intra‐event relations. The sediment yield of individual events is large, but the small number of floods limits the mean annual sediment yield to low values in this arid environment. This also has environmental implications, as large‐scale quarrying requires a long period of self‐restoration in such an arid fluvial setting. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
8.
Nicholas J. C. Doriean Andrew P. Brooks Peter R. Teasdale David T. Welsh William W. Bennett 《水文研究》2020,34(16):3426-3438
Gully erosion is a significant source of fine suspended sediment (<63 μm) and associated nutrient pollution to freshwater and marine waterways. Researchers, government agencies, and monitoring groups are currently using monitoring methods designed for streams and rivers (e.g., autosamplers, rising stage samplers, and turbidity loggers) to evaluate suspended sediment in gullies. This is potentially problematic because gullies have several hydrological features and monitoring operational challenges that differ to those of continually flowing streams and rivers (e.g., short and intense flows, high suspended sediment concentrations, and rapid scouring and aggradation). Here we present a laboratory and field-based assessment of the performance of common suspended sediment monitoring techniques applied to gullies. We also evaluate a recently-described method; the pumped active suspended sediment (PASS) sampler, which has been modified for monitoring suspended sediment in gully systems. Discrete autosampling provided data at high temporal resolution, however, it had poor collection efficiency (25 ± 10%) of coarser sediment particles (i.e., sand). Rising stage sampling, while robust and cost-effective, suffered from large amounts of condensation under field conditions (25–35% of sampler volume), due to harsh climatic conditions creating large diurnal temperature differences at the field site, thereby diluting sample concentrations and introducing additional measurement uncertainty. The turbidity logger exhibited a highly variable response when calibrated at each site with physically collected suspended sediment samples (R2 = 0.17–0.83), highlighting that this approach should be used with caution. The modified PASS sampler proved to be a reliable and representative measurement method for gully sediment water quality, however, the time-integrated nature of the method limits its temporal resolution compared to the other monitoring methods. We recommend monitoring suspended sediment in alluvial gully systems using a combination of complementary techniques (e.g., PASS and RS samplers) to account for the limitations associated with individual methods. 相似文献
9.
Sedimentation in the floodplains of the Mekong Delta,Vietnam. Part I: suspended sediment dynamics 
下载免费PDF全文
下载免费PDF全文 Nguyen Nghia Hung José Miguel Delgado Andreas Güntner Bruno Merz András Bárdossy Heiko Apel 《水文研究》2014,28(7):3132-3144
Suspended sediment is the primary source for a sustainable agro‐ecosystem in the Mekong Delta by providing nutrient input for the subsequent cropping season. In addition, the suspended sediment concentration (SSC) plays an important role in the erosion and deposition processes in the Delta; that is, it influences the morphologic development and may counteract the deltaic subsidence and sea level rise. Despite this importance, little is known about the dynamics of suspended sediment in the floodplains of the Mekong Delta. In particular, quantitative analyses are lacking mainly because of data scarcity with respect to the inundation processes in the floodplains. In 2008, therefore, a comprehensive in situ system to monitor the dynamics of suspended sediment in a study area located in the Plain of Reeds was established, aiming at the characterization and quantification of suspended sediment dynamics in the deeply inundated parts of the Vietnamese part of the Mekong Delta. The monitoring system was equipped with seven water quality–monitoring stations. They have a robust design and autonomous power supply suitable for operation on inundated floodplains, enabling the collection of reliable data over a long period of time with a high temporal resolution. The data analysis shows that the general seasonal dynamics of suspended sediment transport in the Delta is controlled by two main mechanisms: the flood wave of the Mekong River and the tidal backwater influences from the coast. In the channel network, SSC decreases exponentially with distance from the Mekong River. The anthropogenic influence on SSC could also be identified for two periods: at the start of the floodplain inundation and at the end of the flood period, when subsequent paddy rice crops are prepared. Based on the results, we recommend an operation scheme for the sluice gates, which intends to distribute the sediment and thus the nutrients equally over the floodplain. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
10.
The geomorphology of the southern Yellow Sea（SYS） is characterized by offshore radial sand ridges（RSR）.An offshore tidal channel（KSY Channel） is located perpendicular to the coast,comprised of a main and a tributary channel separated by a submarine sand ridge（KSY Sand Ridge） extending seaward.In order to investigate the interactions among water flow,sediment transport,and topography,current velocity and suspended sediment concentration（SSC） were observed at 11 anchor stations along KSY Channel in RSR during a spring tide cycle.High resolution bottom topography was also surveyed.Residual currents and tidally averaged suspended sediment fluxes were calculated and analyzed by using the decomposition method.Results suggested that the water currents became stronger landward but with asymmetrical current speed and temporal duration of flood and ebb tides.Residual currents showed landward water transport in the nearshore channel and a clockwise circulation around the KSY Sand Ridge.Tidally-averaged SSC also increased landward along the channel.The main mechanisms controlling SSC variations were resuspension and horizontal advection,with spatial and temporal variations in the channel,which also contributed to sediment redistribution between channels and sand ridges.Residual flow transport and the tidal pumping effect dominated the suspended sediment flux in the KSY Channel.The KSY Sand Ridge had a potential southward migration due to the interaction between water flow,sediment transport,and topography. 相似文献
11.
12.
Nicholas J.C. Doriean Peter R. Teasdale David T. Welsh Andrew P. Brooks William W. Bennett 《水文研究》2019,33(5):678-686
The accurate measurement of suspended sediment (<200 μm) in aquatic environments is essential to understand and effectively manage changes to sediment, nutrient, and contaminant concentrations on both temporal and spatial scales. Commonly used sampling techniques for suspended sediment either lack the ability to accurately measure sediment concentration (e.g., passive sediment samplers) or are too expensive to deploy in sufficient number to provide landscape‐scale information (e.g., automated discrete samplers). Here, we evaluate a time‐integrated suspended sediment sampling technique, the pumped active suspended sediment (PASS) sampler, which collects a sample that can be used for the accurate measurement of time‐weighted average (TWA) suspended sediment concentration and sediment particle size distribution. The sampler was evaluated against an established passive time‐integrated suspended sediment sampling technique (i.e., Phillips sampler) and the standard discrete sampling method (i.e., manual discrete sampling). The PASS sampler collected a sample representative of TWA suspended sediment concentration and particle size distribution of a control sediment under laboratory conditions. Field application of the PASS sampler showed that it collected a representative TWA suspended sediment concentration and particle size distribution during high flow events in an urban stream. The particle size distribution of sediment collected by the PASS and Phillips samplers were comparable and the TWA suspended sediment concentration of the samples collected using the PASS and discrete sampling techniques agreed well, differing by only 4% and 6% for two different high flow events. We should note that the current configuration of the PASS sampler does not provide a flow‐weighted measurement and, therefore, is not suitable for the determination of sediment loads. The PASS sampler is a simple, inexpensive, and robust in situ sampling technique for the accurate measurement of TWA suspended sediment concentration and particle size distribution. 相似文献
13.
The sediment carrying capacity is one of the fundamental issues in sediment simulation.It is of great importance both in theory and practice to develop process-based approaches for the sediment carrying capacity for a wider range of silt-sand sediment.The current study focuses on the approach for depth-averaged concentration of silt-sand sediment under non-breaking wave conditions.By integrating process-based suspended sediment concentration(SSC) profiles,new synthetic expressions for depth-aver... 相似文献
14.
Ricardo N. Szupiany Cecilia Lopez Weibel Massimo Guerrero Francisco Latosinski Molly Wood Lucas Dominguez Ruben Kevin Oberg 《地球表面变化过程与地形》2019,44(6):1295-1308
Quantifying sediment flux within rivers is a challenge for many disciplines due, mainly, to difficulties inherent to traditional sediment sampling methods. These methods are operationally complex, high cost, and high risk. Additionally, the resulting data provide a low spatial and temporal resolution estimate of the total sediment flux, which has impeded advances in the understanding of the hydro-geomorphic characteristics of rivers. Acoustic technologies have been recognized as a leading tool for increasing the resolution of sediment data by relating their echo intensity level measurements to suspended sediment. Further effort is required to robustly test and develop these techniques across a wide range of conditions found in natural river systems. This article aims to evaluate the application of acoustic inversion techniques using commercially available, down-looking acoustic Doppler current profilers (ADCPs) in quantifying suspended sediment in a large sand bed river with varying bi-modal particle size distributions, wash load and suspended-sand ratios, and water stages. To achieve this objective, suspended sediment was physically sampled along the Paraná River, Argentina, under various hydro-sedimentological regimes. Two ADCPs emitting different sound frequencies were used to simultaneously profile echo intensity level within the water column. Using the sonar equation, calibrations were determined between suspended-sand concentrations and acoustic backscatter to solve the inverse problem. The study also analyzed the roles played by each term of the sonar equation, such as ADCP frequency, power supply, instrument constants, and particle size distributions typically found in sand bed rivers, on sediment attenuation and backscatter. Calibrations were successfully developed between corrected backscatter and suspended-sand concentrations for all sites and ADCP frequencies, resulting in mean suspended-sand concentration estimates within about 40% of the mean sampled concentrations. Noise values, calculated using the sonar equation and sediment sample characteristics, were fairly constant across evaluations, suggesting that they could be applied to other sand bed rivers. © 2018 John Wiley & Sons, Ltd. 相似文献
15.
Few hyperpycnal flows have ever been observed in marine environments although they are believed to play a critical role in sediment dispersal within estuarine and deltaic depositional systems. The paper describes hyperpycnal flows observed in situ off the Huanghe (Yellow River) mouth, their relationship to tidal cycles, and the mechanisms that drive them. Simultaneous observations at six mooring stations during a cruise off the Huanghe mouth in the flood season of 1995 suggest that hyperpycnal flows observed at the river mouth are initiated by high concentrations of sediment input from river and modulated by tides. Hyperpycnal flows started near the end of ebb tides, when near‐bottom suspended sediment concentration (SSC) increased rapidly and salinity decreased drastically (an inverse salt wedge). The median grain size of suspended particles within the hyperpycnal layer increased, causing strong stratification of the suspended sediments in the water column. Towards the end of flood tides, the hyperpycnal flow attenuated due to frictions at the upper and lower boundaries of the flow and tidal mixing, which collapsed the stratification of the water column. Both sediment concentration and median grain size of suspended particles within the bottom layer significantly decreased. The coarser sediment particles were deposited and the hyperpycnal flows stopped. The intra‐tidal behaviors of hyperpycnal flows are closely associated with the variations of SSC, salinity, and stratification of the water column. As nearly 90% of riverine sediment is delivered to the sea during the flood seasons when hyperpycnal flows are active, hyperpycnal flows at the Huanghe mouth and the river's high sediment loads have caused rapid accretion of the Huanghe delta. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
16.
《水文科学杂志》2013,58(6):899-915
Abstract The results are described of 16 years operation of a measuring station for the automatic recording of water discharge, bed load and suspended sediment transport in the Rio Cordon catchment, a small alpine basin (5 km2) located in northeastern Italy. Hillslope erosion processes were investigated by surveying individual sediment sources repeatedly. Annual and seasonal variations of suspended sediment load during the period 1986–2001 are analysed along with their contribution to the total sediment yield. The results show that suspended load accounted for 76% of total load and that most of the suspended sediment transport occurred during two flood events: an extreme summer flash flood in September 1994 (27% of the 16-years total suspended load) and a snowmelt-induced event in May 2001 accompanied by a mud flow which fed the stream with sediments. The role of active sediment source areas is discussed in relation to the changes in flood peak—suspended load trends which became apparent after both the 1994 and the 2001 events. 相似文献
17.
Suspended sediment concentrations (SSCs) in rivers are variable in time due to interacting soil erosion and sediment transport processes. While many hydro-meteorological variables are correlated to SSCs, interpretation of these correlations in terms of driving processes requires in-depth knowledge of the catchment. Detailed sediment source information is needed to establish the causal linkages between driving processes and variations in SSC. This study innovatively combined sediment fingerprinting with multivariate statistical analyses of hydro-meteorological data to investigate how differential contributions of sediment sources control SSC in response to hydro-meteorological variables during high-flow events in rivers. Applied to the River Aire (UK), five sediment sources were classified: grassland topsoil in three lithological areas (limestone, millstone grit and coal measures), eroding riverbanks, and street dust. A total of 159 suspended sediment samples were collected during 14 high-flow events (2015–2017). Results show substantial variation in sediment sources during high-flow events. Limestone grassland and street dust, the dominant contributors to the suspended sediment, show temporal variations consistent with variations in total SSC, and are correlated with precipitation and discharge shortly prior and during high-flow events (i.e. fast mobilization to and within river). Contrarily, contributions from millstone and coals grassland appear to be driven by antecedent hydro-meteorological conditions (i.e. lag-time between soil erosion and sediment delivery). Riverbank material is poorly correlated to hydro-meteorological variables, possibly due to weak source discrimination or the infrequent nature of its delivery to the channel. Differences in source-specific drivers and process interactions for sediment transport demonstrate the difficulty in generalizing sediment transport patterns and developing targeted suspended sediment management strategies. While more research is essential to address different uncertainties emerging from the approach, the study demonstrates how empirical data on sediment monitoring, fingerprinting, and hydro-meteorology can be combined and analysed to better understand sediment connectivity and the factors controlling SSC. © 2019 John Wiley & Sons, Ltd. © 2019 John Wiley & Sons, Ltd. 相似文献
18.
In laboratory experiments, the influence of inflow and outflow sequences on the behavior of fine sedi-ment was investigated. The experimental set-up consisted of two interconnected rectangular basins, between which water was moved back and forth. Suspended sediment concentration in the main basin as well as the sediment exchange rates were derived from turbidity measurements.The suspended sediment ratio, SSR, and sediment exchange rates (influx sediment rate, ISR, and evacuated sediment rate, ESR) were measured. In twenty test runs, a parametric study on the magnitude and frequency of inflow and outflow cycles, the relative duration between inflow and outflow sequences, the initial sediment concentration, and the intake position was done. An initial test with stagnant water described the set-tling behavior of fine sediment and served as a reference scenario.The test results show that settling of fine particles near the intake/outlet structure can be considerably reduced by the nature of the inflow and outflow sequences. High cycle magnitude and frequency lead to maximum suspended sediment ratio in the system. For low discharges, the evolution of suspended sediment concentration cannot be directly correlated to the inflow and outflow cycles. However, compared to"no operation"conditions, the suspended sediment ratio could be increased by 10%to 40%locally. For high discharge, the evolution of suspended sediment concentration correlated with discharge cycles and suspended sediment ratios between 50%and 80%higher than for stagnant water could be achieved. Similar ratios could be obtained when the intake is located closer to the bottom or to the free water surface.Meanwhile, the overall sediment balance remained in equilibrium over the test period, indicating that the influx and evacuated sediment rates are not significantly influenced by the inflow and outflow cycles. 相似文献
19.
One year of instantaneous suspended sediment concentration, C, and instantaneous discharge, Q, data collected at Ngarradj downstream of the Jabiluka mine site indicate that the use of a simple C–Q rating curve is not a reliable method for estimating suspended sediment loads from the Ngarradj catchment. The C–Q data are not only complicated by hysteresis effects within the rising and falling stages of individual events, but also by variable depletion of available suspended sediment through multipeaked runoff events. Parameter values were fitted to an event‐based suspended sediment load–Q relationship as an alternative to the C–Q relationship. Total suspended sediment load and Q data for 10 observed events in the Ngarradj stream catchment were used to fit parameter values to a suspended sediment load–Q relationship, using (a) log–log regression and (b) iterative parameter fitting techniques. A more reliable and statistically significant prediction of suspended sediment load from the Ngarradj catchment is obtained using an event‐based suspended sediment load–Q relationship. Fitting parameters to the event‐based suspended sediment load–Q relationship using iterative techniques better predicts long‐term suspended sediment loads compared with log–log regression techniques. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
20.
Jiongxin Xu 《地球表面变化过程与地形》2002,27(7):749-758
Based on the data from alluvial rivers in China, the complex mechanical behaviour of sediment‐carrying streamflow of natural rivers has been observed. Channel geometry also exhibits complex behaviour in response to variation in suspended concentration. With the increase in suspended concentration, channel width : depth ratio increases, reaches a maximum and then decreases. The inverse is true for channel sinuosity. When suspended concentration is low, a meandering pattern is dominant. The increase in suspended concentration leads to a transformation from a meandering to a braided pattern. But when the suspended concentration increases further and enters the range of hyperconcentrated flows, the meandering pattern appears. The complex behaviour of channel pattern change may be regarded as a reflection of the complex behaviour of sediment‐carrying streamflows at the river reach scale. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献