首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
The use of a single-bowl continuous-flow centrifuge (CFC, Sharples-Pennwalt Model AS-12) for dewatering suspended sediment from large volumes of river water is evaluated. Sediment-recovery efficiency of 86-91 per cent is comparable to that of other types of CFC units. The recovery efficiency is limited by the particle-size distribution of the feed water and by the limiting particle diameter that is retained in the centrifuge bowl. The limiting particle diameter, using the parameters for this study (bowl radius = 10.5cm; bowl length = 71.1 cm; rotational velocity = 16000 r min?1; flow rate = 2 L min?1, and an assumed hydrated particle density = 1.7 gm cm?3), is 370 nm. There seems to be no particle-size fractionation within the centrifuge bowl—the median particle size was the same at the top as at the bottom. Particle electrophoretic mobility plays some role in fractionation of particles within the centrifuge. The mobility ranged from ?1.19 to ?2.01 × 10?8 m2 V?1 s?1, which is typical of clays coated with organic matter, the charge of which is partially neutralized by divalent cations and iron. Contamination by trace metals and organics is minimized by coating all surfaces that come in contact with the sample with either FEP or PFA Teflon and using a removable FEP Teflon liner in the centrifuge bowl. Because of the physical and chemical factors affecting particle fractionation within the centrifuge, care must be exercised in interpreting the environmental consequences of particles collected by continuous-flow centrifugation.  相似文献   

2.
A method for collecting suspended sediment samples has been developed that pumps a discharge-weighted volume of water from fixed depths at four to 40 locations across a river and separates the suspended sediment in the sample using a continuous-flow centrifuge. The efficacy of the method is evaluated by comparing the particle size distributions of sediment collected by the discharge-weighted pumping method with the particle size distributions of sediment collected by depth integration and separated by gravitational settling. The pumping method was found to undersample the suspended sand sized particles (> 63 μm) but to collect a representative sample of the suspended silt and clay sized particles (< 63 μm). The centrifuge separated the silt and clay sized particles (< 63 μm) into three fractions. Based on the average results of processing 17 samples from the Mississippi River and several of its large tributaries in 1990, about 10% of the silt and clay sized material was trapped in a centrifuge bowl-bottom sealing unit containing the nozzle and consisted of mostly medium and coarse silt from 16 to 63 μm. About 74% was retained on a Teflon liner in the centrifuge bowl and consisted of sizes from 0–1 to 63 μm. About 9% was discharged from the centrifuge in the effluent and was finer than 0–1 μm. About 7% was lost during the processes of removing the wet sediment fractions from the centrifuge, drying and weighing. The success of the discharge-weighted pumping method depends on how homogeneously the silt and clay sized particles (< 63 μm) are distributed in the vertical direction in the river. The degree of homogeneity depends on the composition and degree of aggregation of the suspended sediment particles.  相似文献   

3.
This study examines the effect of drawdown on the timing and magnitude of suspended solids and associated phosphorus export from a 12 ha reservoir located in an urbanized watershed in southern Ontario, Canada. Water level in Columbia Lake was lowered by 1·15 m over a 2‐week period in November 2001. The total phosphorus (TP) concentrations ranged from 63 to 486 µg L?1 in Columbia Lake and 71 to 373 µg L?1 at its outflow. All samples exceeded the Provincial Water Quality Objective of 30 µg TP L?1. Outflow concentrations of suspended solids and TP increased significantly with decreasing lake level and were attributed to the resuspension of cohesive bottom sediments that occurred at a critical threshold lake level (0·65 m below summer level). Suspended solids at the outflow consisted of flocculated cohesive materials with a median diameter (D50) of c. 5 µm. Particulate organic carbon accounted for 8·5% of the suspended solids export by mass. A total mass of 18·5 t of suspended solids and 62·6 kg TP was exported from Columbia Lake, which represents a significant pulse of sediment‐associated P to downstream environments each autumn during drawdown. The downstream impacts of this release can be minimized if the water level in Columbia Lake is lowered no more than 0·5 m below summer levels. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

4.
Laboratory experiments were performed with rain of uniform drop size (2·7 mm, 5·1 mm) impacting flows over non‐cohesive beds of uniform sized sand (0·11–0·9 mm) and coal (0·2–0·9 mm) particles with flow velocities (20 mm s?1, 40 mm s?1) that were insufficient for the flow to entrain the particles without the aid of raindrop impact. Measurement of particle travel distance under rain made up of 2·7 mm drops confirmed a theoretical relationship between settling velocity and the distance particles travel after being disturbed by drop impact. Although, in theory, a relationship between settling velocity and particle travel distance exists, settling velocity by itself was unable to account for the effect of changes in both particle size and density on sediment discharge from beds of uniform non‐cohesive material. Particle density was also a factor. Further study of how particle characteristics influence sediment discharge will aid modelling of the impact of the soil in process‐based models of erosion by rain‐impacted flow. Copyright © 2001 John Wiley & Sons, Ltd.  相似文献   

5.
The performance of a constructed wetland for wastewater treatment was examined for four months (December 1995 to March 1996). The study area, hereby referred to as the Splash wetland, is approximately 0·5 ha, and is located in the southern part of Nairobi city. Splash wetland continuously receives domestic sewage from two busy restaurants. Treated wastewater is recycled for re‐use for various purposes in the restaurants. Both wet and dry season data were analysed with a view of determining the impact of seasonal variation on the system performance. The physical and chemical properties of water were measured at a common intake and at series of seven other points established along the wetland gradient and at the outlet where the water is collected and pumped for re‐use at the restaurants. The physico‐chemical characteristics of the wastewater changed significantly as the wastewater flowed through the respective wetland cells. A comparison of wastewater influent versus the effluent from the wetland revealed the system's apparent success in water treatment, especially in pH modification, removal of suspended solids, organic load and nutrients mean influent pH = 5·7 ± 0·5, mean effluent pH 7·7 ± 0·3; mean influent BOD5 = 1603·0 ± 397·6 mg/l, mean effluent BOD5 = 15·1 ± 2·5 mg/l; mean influent COD = 3749·8 ± 206·8 mg/l, mean effluent COD = 95·6 ± 7·2 mg/l; mean influent TSS = 195·4 ± 58·7 mg/l, mean effluent TSS = 4·7 ± 1·9 mg/l. As the wastewater flowed through the wetland system dissolved free and saline ammonia, NH4+, decreased from 14·6 ± 4·1 mg/l to undetectable levels at the outlet. Dissolved oxygen increased progressively through the wetland system. Analysis of the data available did not reveal temporal variation in the system's performance. However, significant spatial variation was evident as the wetland removed most of the common pollutants and considerably improved the quality of the water, making it safe for re‐use at the restaurants. Copyright © 2001 John Wiley & Sons, Ltd.  相似文献   

6.
Deposition and storage of fine‐grained (<62·5 μm) sediment in the hyporheic zone of gravel bed rivers frequently represents an important cause of aquatic habitat degradation. The particle size characteristics of such fine‐grained bed sediment (FGBS) exert an important control on its hydrodynamic properties and environmental impact. Traditionally, particle size analysis of FGBS in gravel bed rivers has focused on the absolute size distribution of the chemically dispersed mineral fraction. However, recent work has indicated that in common with fluvial suspended sediment, significant differences may exist between the absolute and the in situ, or effective, particle size composition of FGBS, as a result of the existence of aggregates, or composite particles. In the investigation reported in this paper, sealable bed traps that could be remotely opened to sample sediment deposited during specific storm runoff events and a laser back‐scatter probe were used to quantify the temporal and spatial variability of both the absolute and effective particle size composition of FGBS, and the associated suspended sediment from four gravel bed rivers in the Exe Basin, Devon, UK. The absolute particle size distributions of both the FGBS and suspended sediment evidenced c. >95%<62·5 μm sized primary particles and displayed a seasonal winter–summer fining, while the opposite trend was displayed by the effective particle size distribution of the FGBS and suspended sediment. The effective particle size distributions of both were typically highly aggregated, comprising up to 68%>62·5 μm sized particles. Spatial variation in the effective particle size and aggregation parameters was of secondary importance relative to temporal variation. The effective particle size distribution of the FGBS was consistently coarser and more aggregated than the associated suspended sediment and there was evidence of aggregate break‐up in samples of resuspended bed sediment. The implications of these findings for sediment transport modelling are considered. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

7.
S. C. Bird 《水文研究》1987,1(4):321-338
Suspended solids contamination caused by runoff below a working colliery in the Upper Clydach catchment in South Wales, U.K., was investigated in relation to hydrological controls. Field studies over a 16 month period found that concentrations below the colliery ranged from 4 to 8028 mg 1?1. Simple correlation and linear regression analysis of spot and storm event samples taken below the colliery gave a correlation coefficient of 0·39 between flow and suspended solids concentration. Because of the lack of explained variance, a multiple linear regression model of within-storm concentrations was derived using four selected independent variables. X1 the time relation of the sample to the storm peak; log X2 the stormflow at the time of sampling; log X3 the baseflow at the time of sampling; and log X4 an index of the storm intensity. Analysis of the entire dataset gave an R2 of 0·34. When the results from three atypical events were excluded however, the R2 value improved to 0·65. Beta coefficients indicated that rising limb conditions (X1) and intense storms (log X4) along with dry antecedent conditions (log X3) represent the worst combination of hydrological factors for producing suspended solids contamination.  相似文献   

8.
Stream–subsurface exchange strongly influences the transport of contaminants, fine particles, and other ecologically relevant substances in streams. We used a recirculating laboratory flume (220 cm long and 20 cm wide) to study the effects of particle size, overlying velocity, and biofilm formation on stream–subsurface exchange of particles. Sodium chloride was used as a non‐reactive dissolved tracer and 1‐ and 5‐µm fluorescent microspheres were used as particulate tracers. Surface–subsurface exchange was observed with a clean sand bed and a bed colonized by an autotrophic–heterotrophic biofilm under two different overlying velocities, 0·9 and 5 cm s?1. Hydrodynamic interactions between the overlying flow and sand bed resulted in a reduction of solute and particle concentrations in the water column, and a corresponding accumulation of particles in both the sediments and in the biofilm. Increasing overlying velocity and particle size resulted in faster removal from the overlying water due to enhanced mass transfer to the bed. The presence of the biofilm did not affect solute exchange under any flow condition tested. The presence of the biofilm significantly increased the deposition of particles under an overlying velocity of 5 cm s?1, and produced a small but statistically insignificant increase at 0·9 cm?1. The particles preferentially deposited within the biofilm matrix relative to the underlying sand. These results demonstrate that hydrodynamic transport conditions, particle size, and biofilm formation play a key role in the transport of suspended particles, such as inorganic sediments, particulate organic matter, and pathogenic microorganisms in freshwater ecosystems, and should be taken into consideration when predicting the fate and transport of particles and contaminants in the environment. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

9.
The occurrence and fate of six phthalate esters were investigated in the River Seine and two tributaries in the Paris area, at six sites from upstream to downstream, throughout different seasons, with special attention given to a flood episode. At all sites, except the River Marne, whatever the period, diethylhexyl phthalate (DEHP) displayed the highest concentration (0·323–0·779 µg l?1 as mean values), followed by di‐n‐butyl phthalate (DnBP; 0·211–0·526 µg l?1 as mean values), which is consistent with the production pattern. High phthalate concentrations appeared to be related to population density and industrial distribution. The strongest values were located downstream from wastewater treatment plant effluent inputs. Seasonal variations were closely related to river flow and air and water temperature. The annual evolution of phthalates was linked to the hydrological conditions. During the flood episode at Paris, the DEHP concentration displayed a sharp increase (260 to 1123 ng l?1) occurring 9 days before the flood peak. The simultaneous fluctuations of NH4, typical of domestic origin, and of DEHP suggests a similar origin from combined sewer overflows for both compounds. Other elevated values corresponded to the highest precipitation amounts, and demonstrated the contribution of non‐point‐source runoff and wastewater overflow to DEHP inputs. The DEHP concentration relationship with river flow displayed a clockwise hysteresis loop, corresponding to a ‘first‐flush’ effect in which the finite supplies are swept along in the early stage of the flood. Annual fluxes for 2004 at Paris were 2257 kg of DEHP and 1613 kg of DnBP. The flood period seemed to have a minor impact on annual phthalate transport (29·5% and 41% of the total for DEHP and for DnBP, respectively), which is contrary to annual suspended solids transport (69%). Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

10.
The morphology of suspended sediment particles reflects the origin of the suspended load and any modifying processes that may have occurred during transport and storage in the aquatic system. The objective of this study was to evaluate the use of four fractal dimensions to quantify visually observed changes in the morphology of fluvial suspended sediment particles during baseflow conditions. Samples were collected during summer low flow in a small stream on the Canadian Prairies. Particle morphology data were obtained with a transmitted light microscope, a CCD camera and an image analysis system. The morphology of the particle population was characterized using four fractal dimensions (D, DK, D1 and D2). D was derived from the area–perimeter relationship and showed an increase from 1·26±0·02 on 30 June, to 1·34±0·02 on 4 July, to 1·42±0·01 on 7 July. Visually, the increase in D represented the formation of large particles with intricate shapes and increased perimeters. DK was determined from the area–rank relationship and varied from 1·86±0·01 on 30 June, to 1·90±0·00 on 4 July, to 1·74±0·00 on 7 July. The decrease in DK between 4 July and 7 July would indicate a greater concentration of the particle area over a small number of large particles. Although the decrease in DK is consistent with observed changes in the particle size distributions, DK should be used with the considerable caution because DK varied more than one standard error between replicates. D1 and D2 were determined from the length–perimeter and length–area relationships, respectively. D1 proved to be of little value for quantifying changes in particle morphology as it showed little change with time, despite considerable visual changes. D2 however, was useful, despite some variation between replicates. Over the sampling period, D2 for the composite data sets showed a steady decrease from 1·74±0·02 on 30 June, to 1·68±0·02 on 4 July, to 1·60±0·01 on 7 July. This change in D2 indicates that, through time, the larger particles became longer and thinner relative to the smaller ones. This study shows that temporal changes in D, DK and D2 were consistent with, and allow quantification of, observed changes in particle morphology. D1 did not reflect observed morphological changes, and is therefore of little value for this type of study. The changes in particle morphology coincided with an increase in primary production in the form of algae. © 1997 John Wiley & Sons, Ltd.  相似文献   

11.
Laboratory flume experiments were carried out to evaluate the effect of particle density on bedload transport of sand‐sized particles and the effect of a suspended load of clay particles (kaolinite) on bedload transport of sand‐sized particles in rill flow conditions. Three materials in the range 400–600 µm were selected to simulate bedload transport of primary particles and aggregates: sand (2650 kg/m3), crushed brick (2450 kg/m3) and anthracite (1300–1700 kg/m3). In the two first experiments, two different methods were applied to determine bedload transport capacity of coarse particles for various conditions of flow discharge (from 2 to 15 L/min) and slope (2.2, 3 and 4%). In the third experiment, clear water was replaced with kaolinite–water mixture and bedload transport capacity of crushed brick particles was determined for a 4% slope and different concentrations of kaolinite (0, 7, 41 and 84 g/L). The results showed that bedload transport increased significantly with the decrease in particle density but the effect of particle density on transport rates was much less important than flow discharge. Velocity measurements of clear flow, flow mixed with coarse particles and coarse particles confirmed the existence of a differentiation between suspended load and bedload. In these experimental conditions, suspended load of kaolinite did not affect bedload rates of crushed brick particles. Three transport capacity formulae were tested against observed bedload rates. A calibration of the Foster formula revealed that the shear stress exponent should be greater than 1.5. The Low and the Govers unit stream power (USP) equations were then evaluated. The Low equation was preferred for the prediction of bedload rates of primary particles but it was not recommended in the case of aggregates of low density because of the limited experimental conditions applied to derive this equation. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

12.
The problem of impact–entrainment relationship is one of the central issues in understanding saltation, a primary aeolian transport mode. By using particle dynamic analyser measurement technology the movement of saltating particles at the very near‐surface level (1 mm above the bed) was detected. The impacting and entrained particles in the same impact–entrainment process were identified and the speeds, angle with respect to the horizontal, and energy of the impacting and entrained sand cloud were analysed. It was revealed that both the speed and angle of impacting and entrained particles vary widely. The probability distribution of the speed of impacting and entrained particles in the saltating cloud is best described by a Weibull distribution function. The mean impact speed is generally greater than the mean lift‐off speed except for the 0·1–0·2 mm sand whose entrainment is significantly influenced by air drag. Both the impact and lift‐off angles range from 0° to 180°. The mean lift‐off angles range from 39° to 94° while the mean impact angles range from 40° to 78°, much greater than those previously reported. The greater mean lift‐off and especially the mean impact angles are attributed to mid‐air collisions at the very low height, which are difficult to detect by conventional high‐speed photography and are generally ignored in the existing theoretical simulation models. The proportion of backward‐impacting particles also evidences the mid‐air collisions. The impact energy is generally greater than the entrainment energy except for the 0·1–0·2 mm sand. There exists a reasonably good correlation of the mean speed, angle and energy between the impacting and entrained cloud in the impact–entrainment process. The results presented in this paper deserve to be considered in modelling saltation. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

13.
Use of a Zeiss Micro-Videomat electronic image analyzer for routine measurements of size distributions of particles found in natural waters greater than 0.3 μm has been investigated. Staining of particles with a solution of Gentiana-violet eliminated the multiple-count problem which has frustrated earlier attempts to use image analyzers for quantitative phytoplankton work. Concentration of samples from the lake water column was successfully achieved with an impact centrifuge. Losses of inorganic particles indicate that the centrifuge method must be evaluated on an individual case basis. Precision and accuracy of the Zeiss Micro-Videomat using either sedimentation (Utermöhl) or centrifugation for sample concentration were satisfactory for particles larger than 1 μm. The system appears promising for routine surveillance of raw water quality at water treatment plants, and performance of unit processes used for particulate removal, as well as for specific investigations of ecological phenomena in natural waters.  相似文献   

14.
Fine‐grained (<62·5 µm) suspended sediment transport is a key component of the geochemical flux in most fluvial systems. The highly episodic nature of suspended sediment transport imposes a significant constraint on the design of sampling strategies aimed at characterizing the biogeochemical properties of such sediment. A simple sediment sampler, utilizing ambient flow to induce sedimentation by settling, is described. The sampler can be deployed unattended in small streams to collect time‐integrated suspended sediment samples. In laboratory tests involving chemically dispersed sediment, the sampler collected a maximum of 71% of the input sample mass. However, under natural conditions, the existence of composite particles or flocs can be expected to increase significantly the trapping efficiency. Field trials confirmed that the particle size composition and total carbon content of the sediment collected by the sampler were representative statistically of the ambient suspended sediment. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

15.
Investigating the transport of suspended solids by water sampling usually leads to an underestimation of loads and an unrealistically high sampling frequency is required to properly characterize temporal trends. An alternative method is to use in situ optical turbidimeters to estimate the suspended solids concentration; however, the relationship between turbidity and suspended solids concentration is potentially confounded by variations in particle size, particle composition and water colour. Field measurements, and laboratory measurements using the type of natural material suspended in streamwater, were made to quantify the influences of these factors on nephelometric turbidity (Hach 2100A) and attenuance turbidity (Partech 7000 3RP MKII). The attenuance turbidity was approximately 2.5 times higher than nephelometric turbidity. The turbidity instruments were most sensitive to dispersions with a median diameter of 1.2-1.4γm. Particle size variation can cause the turbidity to vary by a factor of four for the same concentration of suspended solids. However, the numerous close correlations between turbidity and suspended solids concentration reported previously suggests that either the particle size variations are not usually great, or that particle size variations are often associated with variations in suspended solids concentration. For the same concentration and particle size, organic particles gave attenuance turbidity values two to three times higher than mineral particles. However, shortterm temporal variations from purely organic to purely mineral particle loads are rare in nature, so variations in the percentage of organic matter in the paniculate load will not confound turbidity to this extent. Coloured dissolved organic matter is unlikely to alter the turbidity reading by more than 10%. An adequate relationship between turbidity measured in the field and suspended solids concentration should be expected in most situations. Some variance can be tolerated because a continuous estimate of suspended solids concentration overcomes the problem of infrequent sampling, which is the greatest source of error in the estimation of stream sediment loads.  相似文献   

16.
  相似文献   

17.
Field‐ and laboratory‐scale rainfall simulation experiments were carried out in an investigation of the temporal variability of erosion processes on interrill areas, and the effects of such variation upon sediment size characteristics. Poorly aggregated sandy soils from the semi‐arid environment of Senegal, West Africa, were used on both a 40 m2 field plot and a 0·25 m2 laboratory plot; rainfall intensity for all experiments was 70 mm h?1 with a duration of 1 to 2 hours. Time‐series measurements were made of the quantity and the size distribution of eroded material: these permitted an estimate of the changing temporal balance between the main erosion processes (splash and wash). Results from both spatial scales showed a similar temporal pattern of runoff generation and sediment concentration. For both spatial scales, the dominant erosional process was detachment by raindrops; this resulted in a dynamic evolution of the soil surface under raindrop impact, with the rapid formation of a sieving crust followed by an erosion crust. However, a clear difference was observed between the two scales regarding the size of particles detached by both splash and wash. While all measured values were lower than the mean weight diameter (MWD) value of the original soil (mean 0·32 mm), demonstrating the size‐selective nature of wash and splash processes, the MWD values of washed and splashed particles at the field scale ranged from 0·08 to 0·16 mm and from 0·12 to 0·30 mm respectively, whereas the MWD values of washed and splashed particles at the laboratory scale ranged from 0·13 to 0·29 mm and from 0·21 to 0·32 mm respectively. Thus only at the field scale were the soil particles detached by splash notably coarser than those transported by wash. This suggests a transport‐limited erosion process at the field scale. Differences were also observed between the dynamics of the soil loss by wash at the two scales, since results showed wider scatter in the field compared to the laboratory experiments. This scatter is probably related to the change in soil surface characteristics due to the size‐selectivity of the erosion processes at this spatial scale. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

18.
This paper examines a variety of recirculation flow patterns that develop in the groyne fields on rivers. A comprehensive data set was obtained from flume experiments at Delft University of Technology and field measurements performed on the Elbe River in Germany. The analysis focuses on patterns of velocity, scour and deposition, and corresponding change of riverbed morphology. The results show that velocity patterns in the groyne fields depend mainly on the aspect ratio between groyne length and length of groyne field. When the aspect ratio is greater than 0·5, a one‐gyre pattern of recirculation develops, while at groyne fields with aspect ratios less than 0·5 a two‐gyre recirculation pattern emerges. The spatial distribution of fine‐sediment deposition between the groynes coincides with the locations of gyres. Moreover, the thickness of the fine‐sediment layer decreases toward the gyre margins where recirculation velocities are greatest. Although the total concentration of suspended sediment in the river does not change considerably as the flow moves through the groyne field, the biological and gravimetrical composition of the suspended material changes substantially within the groyne field. These changes are due to preferential deposition of coarse mineral particles and the replacement of those minerals with finer organic material. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

19.
This study concerns the problem of water erosion in the Sahel. Surface water and sediment yields (suspended matter and bedload) were monitored for 3 years (1998–2000) at the outlet of a small grazed catchment (1·4 ha) in the northern part of Burkina Faso. The catchment consists of about 64% sandy deposits (DRY soil surface type), which support most of the vegetation, and about 34% of crusted bare soils (ERO soil surface type). The annual solid‐matter export is more than 90% suspended sediment, varying between 4·0 and 8·4 t ha?1. The bedload represents less than 10% of soil losses. In a single flood event (10 year return period), the sediment yield can reach 4·2 t ha?1. During the period studied, a small proportion (20 to 32%) of the floods was thus responsible for a large proportion (80%) of the solid transport. Seasonal variation of the suspended‐matter content was also observed: high mean values (9 g l?1) in June, decreasing in July and stabilizing in August (between 2 and 4 g l?1). This behaviour may be a consequence of a reorganization of the soil surfaces that have been destroyed by trampling animals during the previous long dry season, vegetation growth (increase in the protecting effect of the herbaceous cover) and, to a lesser extent, particle‐supply limitation (exhaustion of dust deposits during July). The particle‐size distribution in the suspended matter collected at the catchment outlet is 60% made up of clay: fraction ≤2 µ m. The contribution of this clay is maximum when the water rises and its kaolinite/quartz ratio is then close to that of the ERO‐type surfaces. This indicates that these surfaces are the main source of clay within the catchment. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

20.
Most of the existing data on the effective particle size characteristics of fluvial suspended sediment derive from instantaneous sampling methods that may not be representative of the overall suspended sediment loads. This presents difficulties when there is a need to incorporate effective particle size data into numerical models of floodplain sedimentation and sediment‐associated contaminant transfer. We have used a field‐based water elutriation apparatus (WEA) to assemble a large (36 flood) database on the time‐integrated nature of the effective and absolute particle size characteristics of suspended sediment in four subcatchments of the River Exe basin of southwest England. These catchments encompass a wide range of terrains and fluvial environments that are broadly representative of much of the UK and temperate, low relief northwest Europe. The WEA provides important data on the physical characteristics of composite particles that are not attainable using other methods. This dataset has allowed, for the first time, detailed interbasin comparisons of the time‐integrated particle size characteristics of suspended sediment and reliable estimates of the contribution of five effective size classes to the mean annual suspended sediment load of the study catchments. The suspended sediment load of each river is dominated by composite rather than primary particles, with, for example, almost 60% (by mass) of the sediment load of the River Exe at Thorverton transported as composite particles > 16 µm in size. All the effective size classes contain significant clay components. A key outcome of this study is the recognition that each catchment has a distinctive time‐integrated effective particle size signature. In addition, the time‐integrated effective particle size characteristics of the suspended loads in each of the catchments display much greater spatial variability than the equivalent absolute particle size distributions. This indicates that the processes producing composite particles vary significantly between these catchments, and this has important implications for our understanding of the dynamics of suspended sediment properties. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号