共查询到20条相似文献，搜索用时 649 毫秒
1.
The transfer processes within and above a simulated urban street canyon were investigated in a generic manner. Computational
fluid dynamics (CFD) was used to aid understanding and to produce some simple operational parameterisations. In this study
we addressed specifically the commonly met situation where buoyancy effects arising from elevated surface temperatures are
not important, i.e. when mechanical forces outweigh buoyancy forces. In a geophysical context this requires that some suitably
defined Richardson number is small. From an engineering perspective this is interpreted as the important case when heat transfer
within and above urban street canyons is by forced convection. Surprisingly, this particular scenario (for which the heat
transfer coefficient between buildings and the flow is largest), has been less well studied than the situation where buoyancy
effects are important. The CFD technique was compared against wind-tunnel experiments to provide model evaluation. The height-to-width
ratio of the canyon was varied through the range 0.5–5 and the flow was normal to the canyon axis. By setting the canyon’s
facets to have the same or different temperatures or to have a partial temperature distribution, simulations were carried
out to investigate: (a) the influence of geometry on the flow and mixing within the canyon and (b) the exchange processes
within the canyon and across the canyon top interface. Results showed that the vortex-type circulation and turbulence developed
within the canyon produced a temperature distribution that was, essentially, spatially uniform (apart from a relatively thin
near-wall thermal boundary layer) This allowed the temperatures within the street canyon to be specified by just one value
T
can
, the canyon temperature. The variation of T
can
with wind speed, surface temperatures and geometry was extensively studied. Finally, the exchange velocity u
E
across the interface between the canyon and the flow above was calculated based on a heat flux balance within the canyon
and between the canyon and the flow above. Results showed that u
E
was approximately 1% of a characteristic wind velocity above the street canyon. The problem of radiative exchange is not
addressed but it can, of course, be introduced analytically, or computationally, when necessary. 相似文献
2.
Vertical profiles of the structure parameter of temperature C
infT
sup2
in the stable, nocturnal boundary layer (NBL) have been obtained with the analytic models described by Nieuwstadt (1984, 1985) and Sorbjan (1986) and the numerical model of Duynkerke and Driedonks (1987). These theoretical profiles are compared with observed profiles from the meteorological mast at Cabauw, The Netherlands. From the observations, it is found that C
infT
sup2
is large in the surface layer and small at the top of the NBL. Observations during nights with moderate geostrophic winds or during the first few hours of nights with a high geostrophic wind show a continuous decrease of C
infT
sup2
from the surface layer to the top of the NBL. Observations made later on nights with a high geostrophic wind show the development of a maximum of C
infT
sup2
at about three quarters of the NBL. From the comparison with the models, we conclude that the observed profiles are most satisfactorily described by the model of Duynkerke and Driedonks. 相似文献
3.
Turbulence Structure of the Unstable Atmospheric Surface Layer and Transition to the Outer Layer 总被引：4，自引：4，他引：0
K.G. McNaughton 《Boundary-Layer Meteorology》2004,112(2):199-221
We present a new model of the structure of turbulence in the unstable atmospheric surface layer, and of the structural transition between this and the outer layer. The archetypal element of wall-bounded shear turbulence is the Theodorsen ejection amplifier (TEA) structure, in which an initial ejection of air from near the ground into an ideal laminar and logarithmic flow induces vortical motion about a hairpin-shaped core, which then creates a second ejection that is similar to, but larger than, the first. A series of TEA structures form a TEA cascade. In real turbulent flows TEA structures occur in distorted forms as TEA-like (TEAL) structures. Distortion terminates many TEAL cascades and only the best-formed TEAL structures initiate new cycles. In an extended log layer the resulting shear turbulence is a complex, self-organizing, dissipative system exhibiting self-similar behaviour under inner scaling. Spectral results show that this structure is insensitive to instability. This is contrary to the fundamental hypothesis of Monin--Obukhov similarity theory. All TEAL cascades terminate at the top of the surface layer where they encounter, and are severely distorted by, powerful eddies of similar size from the outer layer. These eddies are products of the breakdown of the large eddies produced by buoyancy in the outer layer. When the outer layer is much deeper than the surface layer the interacting eddies are from the inertial subrange of the outer Richardson cascade. The scale height of the surface layer, z
s, is then found by matching the powers delivered to the creation of emerging TEAL structures to the power passing down the Richardson cascade in the outer layer. It is z
s = u
*
3
/ks, where u
* is friction velocity, k is the von Kármán constant and s is the rate of dissipation of turbulence kinetic energy in the outer layer immediately above the surface layer. This height is comparable to the Obukhov length in the fully convective boundary layer. Aircraft and tower observations confirm a strong qualitative change in the structure of the turbulence at about that height. The tallest eddies within the surface layer have height z
s, so z
s is a new basis parameter for similarity models of the surface layer. 相似文献
4.
大气边界层阵风相干结构的产生条件 总被引：1，自引：0，他引：1
壁湍流相干结构的发现是近代湍流研究的重大进展之一,从20世纪50年代开始,在大气边界层湍流中也发现了相干结构——对流云街,并进行了系统的研究。近些年来,人们发现在近地层湍流中也存在相干结构。利用北京325 m气象塔对城市下垫面中大风和小风天气的风速分析,发现较有规律的周期3~6 min的阵风,且有明显的相干结构,而对不同下垫面的阵风研究,均发现存在这种相干结构,这种阵风相干结构对通量输送有不可忽视的作用。本文利用2012年4月甘肃省民勤县巴丹吉林沙漠观测塔的超声风速和平均场风速、温度观测资料,对阵风相干结构的产生条件进行了分析。采用傅立叶变换,将三维超声风速按频率分成基流(周期10分钟以上)、阵风扰动(周期1到10分钟)、湍流脉动(周期小于1分钟)三部分,结合平均场的资料分析发现:阵风相干结构出现在静力中性、不稳定甚至略微稳定的条件下,或者说机械作用主导的大气边界层,阵风区就会出现相干结构,热力作用对其有抑制和干扰的作用。从而,阵风的相干结构和壁面相干结构都出现在中性条件下,是机械湍流的现象,都主导着动量能量的输运。阵风区的相干结构并不等同于对流云街,他们出现在不同的大气稳定度条件下且尺度不同。 相似文献
5.
利用杭瑞高速公路洞庭湖大桥北岸测风塔的梯度风观测资料、三维超声风温仪资料以及岳阳气象站提供的逐小时气溶胶浓度和能见度观测资料,对湖南岳阳2017年1月28日的一次重度霾天气中的重污染过程的近地层物理量变化特征进行了分析,结果表明:（1）重污染来临前约130 min即28日01:50（北京时间,下同）,水平风速、垂直风速、高低层风切变都出现零值,大气处于静稳状态。重污染结束前180 min即28日09:00,上述物理量和高低层温度切变出现零值。（2）湍流强度在重污染来临前有强烈异常信号,其中水平纵向湍流强度异常信号最明显,于重污染发生前130 min出现异常峰值4.15,重污染结束前180 min出现异常峰值3.24。（3）湍流动能和动量通量都在重污染来临前130 min接近0.0 m2/s2,即湍流交换最弱,有利于污染物在近地面的持续堆积和重污染过程的发生。近地层的平均物理量和湍流特征量的异常信号的出现时间有较好的一致性,即出现在重污染来临前的130 min和结束前的180 min。揭示了重度霾污染天气的近地层物理量时间变化规律,着重分析了霾污染的生成、发展、消亡全过程的边界层湍流异常的前期信号,为深入认识霾污染天气进行有益的探索并为这类天气的预测预警提供科学依据。 相似文献
6.
We examine the unsteady response of a neutral atmospheric boundary layer (ABL) of depth h and friction velocity u * when a uniform surface heat flux is applied abruptly or decreased rapidly over a time scale t<inf>θ</inf> less than about h /(10u *). Standard Monin–Obukhov (MO) relationships are used for the perturbed eddy viscosity profile in terms of the changes to
the heat flux and mean shear. Analytical solutions for changes in temperature, mean wind and shear stress profile are obtained
for the surface layer, when there are small changes in h /|LMO| over the time scale tMO~|L MO|/(10u*) (where L MO and t MO are the length and time scales, respectively). They show that a maximum in the wind speed profile occurs at the top of the
thermal boundary layer for weak surface cooling, i.e. a wind jet, whereas there is a flattening of the profile and no marked
maximum for weak surface heating. The modelled profiles are approximately the same as those obtained from the U.K. Met Office
Unified Model when operating as a mesoscale model at 12-km horizontal resolution. The theoretical model is modified when strong
surface heating is suddenly applied, resulting in a large change in h /|L MO| (>>1), over the time scale t MO. The eddy structure is predicted to change significantly and the addition of convective turbulence increases the shear turbulence
at the ground. A low-level wind jet can form, with convective turbulence adding to the mean momentum of the flow. This was
verified by our laboratory experiment and direct numerical simulations. Additionally, it is shown that the effects of Coriolis
acceleration diminish (rather than as suggested in the literature, amplify) the formation of the wind jets in the situations
considered here. Hence, only when the surface heat flux changes over time scales greater than 1/f (where f is the Coriolis parameter) does the ABL adjust monotonically between its equilibrium states. These results are also applicable
to the ABL passing over spatially varying surface heat fluxes. 相似文献
7.
We present a scheme for parameterising scalar transfer in the urban boundary layer, which is divided into an inertial layer and a roughness layer. The latter is further divided into a shear layer and a canyon layer. In the inertial layer, scalar transfer is determined by turbulence related to canyon macroscopic features, while in the roughness layer, it is determined by shear-generated turbulence, canyon vortex and vortex-generated turbulence. We first describe a conceptual model for the canyon flow and the aerodynamic resistance network, and then estimate the resistances from the point of view of drag partition and vortex advection. The results are compared with the measurements from wind-tunnel experiments. It is found that for small canyon aspect ratio, σc, the transfer velocity increases with σc, reaching a maximum at around σc=0.5 and then decreases with σc. We also show that the scheme is not sensitive to adjustable parameters 相似文献
8.
The atmospheric stable boundary layer (SBL) with a low-level jet is simulated experimentally using a thermally stratified
wind tunnel. The turbulence structure and flow characteristics are investigated by simultaneous measurements of velocity and
temperature fluctuations and by flow visualization. Attention is focused on the effect of strong wind shear due to a low-level
jet on stratified boundary layers with strong stability. Occasional bursting of turbulence in the lower portion of the boundary
layer can be found in the SBL with strong stability. This bursting originates aloft away from the surface and transports fluid
with relatively low velocity and temperature upward and fluid with relatively high velocity and temperature downward. Furthermore,
the relationship between the occurrence of turbulence bursting and the local gradient Richardson number (Ri) is investigated.
The Ri becomes larger than the critical Ri, Ricr = 0.25, in quiescent periods. On the other hand, the Ri number becomes smaller than Ricr during bursting events. 相似文献
9.
10.
Zbigniew Sorbjan 《Boundary-Layer Meteorology》2006,119(1):57-79
Forced convection in a quasi-steady atmospheric boundary layer is investigated based on a large-eddy simulation (LES) model.
The performed simulations show that in the upper portion of the mixed layer the dimensionless (in terms of mixed layer scales)
vertical gradients of temperature, humidity, and wind velocity depend on the dimensionless height z/z
i
and the Reech number Rn. The peak values of variances and covariances at the top of the mixed layer, scaled in terms of the interfacial scales, are
functions of the interfacial Richardson number Ri. As a result expressions for the entrainment rates, in the case when the interfacial layer has a finite depth, and a condition
for the presence of moistening or drying regimes in the mixed layer, are derived. Profiles of dimensionless scalar moments
in the mixed layer are proposed to be expressed in terms of two empirical similarity functions F
m
and F
i
, dependent on dimensionless height z/z
i
, and the interfacial Richardson number Ri. The obtained similarity expressions adequately approximate the LES profiles of
scalar statistics, and properly represent the impact of stability, shear, and entrainment. They are also consistent with the
parameterization proposed for free convection in the first part of this paper. 相似文献
11.
L. Mahrt Dean Vickers Jim Edson James M. Wilczak Jeff Hare Jørgen Højstrup 《Boundary-Layer Meteorology》2001,100(1):47-61
The adjustment of the boundary layer immediately downstream froma coastline is examined based on two levels of eddy correlation data collected on a mast at the shore and six levels of eddy correlation data and profiles of mean variables collected from a mast 2 km offshore during the Risø Air-Sea Experiment. The characteristics of offshore flow are studied in terms of case studies and inter-variable relationships for the entire one-month data set. A turbulent kinetic energy budget is constructed for each case study.The buoyancy generation of turbulence is small compared to shear generation and dissipation. However, weakly stable and weakly unstable cases exhibit completely different vertical structure. With flow of warm air from land over cooler water, modest buoyancy destruction of turbulence and reduced shear generation of turbulence over the less rough sea surface cause the turbulence to rapidly weaken downstream from the coast. The reduction of downward mixing of momentum by the stratification leads to smaller roughness lengths compared to the unstable case. Shear generation at higher levels and advection of stronger turbulence from land often lead to an increase of stress and turbulence energy with height and downward transport of turbulence energy toward the surface.With flow of cool air over a warmer sea surface, a convective internal boundary layer develops downstream from the coast. An overlying relatively thick layer of downward buoyancy flux (virtual temperature flux) is sometimes maintained by shear generation in the accelerating offshore flow. 相似文献
12.
A. G. Goulart B. E. J. Bodmann M. T. M. B. de Vilhena P. M. M. Soares D. M. Moreira 《Boundary-Layer Meteorology》2011,138(1):61-75
Our focus is the time evolution of the turbulent kinetic energy for decaying turbulence in the convective boundary layer.
The theoretical model with buoyancy and inertial transfer terms has been extended by a source term due to mechanical energy
and validated against large-eddy simulation data. The mechanical effects in a boundary layer of height z
i
at a convective surface-layer height z = 0.05z
i
are significant in the time evolution of the vertical component of the spectrum, i.e. they enhance the decay time scale by
more than an order of magnitude. Our findings suggest that shear effects seem to feedback to eddies with smaller wavenumbers,
preserving the original shape of the spectrum, and preventing the spectrum from shifting towards shorter wavelengths. This
occurs in the case where thermal effects only are considered. 相似文献
13.
The Role of Shear in the Morning Transition Boundary Layer 总被引：1，自引：1，他引：0
Robert J. Beare 《Boundary-Layer Meteorology》2008,129(3):395-410
We use large-eddy simulation (LES) to better define the early stages of the morning transition boundary layer. Previous LES
studies relating to the morning transition boundary layer focus on the role of the entraining convective boundary layer (CBL).
By using a combination of different domain sizes and grid lengths, the full evolution from the stable boundary layer (SBL)
to the CBL is modelled here. In the early stages of the morning transition the boundary layer is shown to be a combination
of a shallow mixed layer capped by a significant shear driven stable boundary layer (the so-called mixed CBL–SBL state). The
mixed CBL–SBL state is the key to understanding the sensitivity to shear. Turbulent kinetic energy budgets also indicate that
it is shear driven. The negative flux from the mixed CBL–SBL state extends much further above the minimum than is typically
found for the CBL later in the day, and the depth of penetration scales as w
m
/N
i
, where w
m
is the combined friction and convective velocity scale and N
i
the static stability at the inversion top. 相似文献
14.
A deep understanding of turbulence structure is important for investigating the characteristics of the atmospheric boundary layer, especially over heterogeneous terrain. In the present study, turbulence intensity and turbulent kinetic energy (TKE) parameters are analyzed for different conditions with respect to stability, wind direction and wind speed over a valley region of the Loess Plateau of China during December 2003 and January 2004. The purpose of the study is to examine whether the observed turbulence intensity and TKE parameters satisfy Monin-Obukhov similarity theory (MOST), and analyze the wind shear effect on, and thermal buoyancy function of, the TKE, despite the terrain heterogeneity. The results demonstrate that the normalized intensity of turbulence follows MOST for all stability in the horizontal and vertical directions, as well as the normalized TKE in the horizontal direction. The shear effect of the wind speed in the Loess Plateau region is strong in winter and could enhance turbulence for all stability conditions. During daytime, the buoyancy and shear effect together constitute the generation of TKE under unstable conditions. At night, the contribution of buoyancy to TKE is relatively small, and mechanical shearing is the main production form of turbulence. 相似文献
15.
The effect of topographical slope angle and atmospheric stratification on turbulence intensities in the unstably stratified surface layer have been parameterized using observations obtained from a three-dimensional sonic anemometer installed at 8 m height above the ground at the Seoul National University (SNU) campus site in Korea for the years 1999–2001. Winds obtained from the sonic anemometer are analyzed according to the mean wind direction, since the topographical slope angle changes significantly along the azimuthal direction. The effects of the topographical slope angle and atmospheric stratification on surface-layer turbulence intensity are examined with these data. It is found that both the friction velocity and the variance for each component of wind normalized by the mean wind speed decrease with increase of the topographical slope angle, having a maximum decreasing rate at very unstable stratification. The decreasing rate of the normalized friction velocity (u
* /U) is found to be much larger than that of the turbulence intensity of each wind component due to the reduction of wind shear with increase in slope angle under unstable stratification. The decreasing rate of the w component of turbulence intensity (σ
w
/U) is the smallest over the downslope surface whereas that of the u component (σ
u
/U) has a minimum over the upslope surface. Consequently, σ
w
/u
* has a maximum increasing rate with increase in slope angle for the downslope wind, whereas σ
u
/u
* has its maximum for the upslope wind. The sloping terrain is found to reduce both the friction velocity and turbulence intensity compared with those on a flat surface. However, the reduction of the friction velocity over the sloping terrain is larger than that of the turbulence intensity, thereby enhancing the turbulence intensity normalized by the friction velocity over sloping terrain compared with that over a flat surface. 相似文献
16.
Sergej Zilitinkevich 《Boundary-Layer Meteorology》1994,70(1-2):51-78
During the last two decades, different scalings for convective boundary layer (CBL) turbulence have been proposed. For the shear-free regime, Deardorff (1970) introduced convective velocity and temperature scales based on the surface potential temperature flux,Q
s
, the buoyancy parameter, , and the time-dependent boundary-layer depth,h. Wyngaard (1983) has proposed decomposition of turbulence into two components, bottom-up (b) and top-down (t), the former characterized byQ
s
, the latter, by the potential temperature flux due to entrainment,Q
h
. Sorbjan (1988) has devised height-dependent velocity and temperature scales for both b- and t-components of turbulence.Incorporating velocity shear, the well known similarity theory of Monin and Obukhov (1954) has been developed for the atmospheric surface layer. Zilitinkevich (1971, 1973) and Betchov and Yaglom (1971) have elaborated this theory with the aid of directional dimensional analysis for a particular case when different statistical moments of turbulence can be alternatively attributed as being of either convective or mechanical origin.In the present paper, we attempt to create a bridge between the two approaches pointed out above. A new scaling is proposed on the basis of, first, decomposition of statistical moments of turbulence into convective (c), mechanical (m) and covariance (c&m) contributions using directional dimensional analysis and, second, decomposition of these contributions into bottom-up and top-down components using height-dependent velocity and temperature scales. In addition to the statistical problem, the scaling suggests a new approach of determination of mean temperature and velocity profiles with the aid of the budget equations for the mean square fluctuations.Notation ATL
alternative turbulence layer
- CBL
convective boundary layer
- CML
convective and mechanical layer
- FCL
free convection layer
- MTL
mechanical turbulence layer 相似文献
17.
Variability Of The Stable And Unstable Atmospheric Boundary-Layer Height And Its Scales Over A Boreal Forest 总被引：3，自引：2，他引：1
S. M. Joffre M. Kangas M. Heikinheimo S. A. Kitaigorodskii 《Boundary-Layer Meteorology》2001,99(3):429-450
Radiosondes releases during the NOPEX-WINTEX experiment carried out in late winter in Northern Finland were analysed for the determination of the height h of the atmospheric boundary layer. We investigate various possible scaling approaches, based on length scales using micrometeorological turbulence surface measurements and the background atmospheric stratification above h. Under stable conditions, the three previously observed turbulence regimes delineated by values of z/L (L is the Obukhov length) appears as a blueprint for understanding the departures found for the suitability of the Ekman scaling based on LE = u/f (u is the friction velocity and f the Coriolis parameter). The length scale LN = u/N (where N is the Brunt–Väisälä frequency) appears to be a useful scale under most stable conditions, especially in association with L. Under unstable conditions, shear production of turbulence is still significant, so that the three scales L, LN and LE are again relevant and the dimensionless ratios N = LN/L and LN/LE = N/f describe well the WINTEX data. Furthermore, in the classical scaling framework, the unstable domain may also be divided into three regimes as reflected by the dependence ofu/f on instability (z/L). 相似文献
18.
Impact of the Diurnal Cycle of the Atmospheric Boundary Layer on Wind-Turbine Wakes: A Numerical Modelling Study 总被引：1，自引：1，他引：0
The wake characteristics of a wind turbine for different regimes occurring throughout the diurnal cycle are investigated systematically by means of large-eddy simulation. Idealized diurnal cycle simulations of the atmospheric boundary layer are performed with the geophysical flow solver EULAG over both homogeneous and heterogeneous terrain. Under homogeneous conditions, the diurnal cycle significantly affects the low-level wind shear and atmospheric turbulence. A strong vertical wind shear and veering with height occur in the nocturnal stable boundary layer and in the morning boundary layer, whereas atmospheric turbulence is much larger in the convective boundary layer and in the evening boundary layer. The increased shear under heterogeneous conditions changes these wind characteristics, counteracting the formation of the night-time Ekman spiral. The convective, stable, evening, and morning regimes of the atmospheric boundary layer over a homogeneous surface as well as the convective and stable regimes over a heterogeneous surface are used to study the flow in a wind-turbine wake. Synchronized turbulent inflow data from the idealized atmospheric boundary-layer simulations with periodic horizontal boundary conditions are applied to the wind-turbine simulations with open streamwise boundary conditions. The resulting wake is strongly influenced by the stability of the atmosphere. In both cases, the flow in the wake recovers more rapidly under convective conditions during the day than under stable conditions at night. The simulated wakes produced for the night-time situation completely differ between heterogeneous and homogeneous surface conditions. The wake characteristics of the transitional periods are influenced by the flow regime prior to the transition. Furthermore, there are different wake deflections over the height of the rotor, which reflect the incoming wind direction. 相似文献
19.
Formation of horizontal convective rolls in urban areas 总被引：6，自引：0，他引：6
The formation of horizontal convective rolls (HCRs) in urban areas is investigated in this paper using observations and fine-scale numerical simulations. Cloud streets organized parallel to the mean boundary-layer wind (a manifestation of HCRs) are seen in the Fengyun-2C satellite imagery around local noon in Beijing. Observed vertical velocity and horizontal wind fields from an urban wind profiler suggest that the time scale for alternating updraft and downdraft in the boundary layer is about 30 min, and the length of the updraft/downdraft is about 9 km. Numerical simulations show that most HCRs occur in the urban areas with − zi / L < 25 (zi: the boundary-layer depth, L: the Monin–Obukhov length). Sensitivity tests reveal that HCRs are common in urban boundary layers, while rural areas are more conducive to forming cellular convection; the aspect ratio of HCRs in urban areas is smaller than the typical value over natural landscapes. 相似文献
