首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Deep cement mixing (DCM) technique is a deep in-situ stabilization technique by mixing cement powder or slurry with soft soils below the ground surface to improve their properties and behavior. Some of DCM treated soft soil grounds are approximately in a plane-strain condition; for example, a fill embankment on DCM improved ground. In this study, a plane-strain physical model was created with instrumentation and used to investigate the bearing capacity and failure mode of a soft soil improved by an end-bearing DCM column group. This study focuses on the observed wedge-shaped shear failure of the model ground and attempts to give an account of the failure. Two different methods are used to calculate the bearing capacity of the model ground, and the computed values are compared with the measured ones. It is found that the simple Brom's method gives a better estimate of the bearing capacity of the present model ground. It is also found that measured data of pore water pressures at different locations in the soft soil indicate coupling between failure of columns and consolidation of the soft soil. This study has presented the first time that a wedge-shaped block failure was observed for pattern of DCM treated soil ground.  相似文献   

2.
Undrained bearing capacity of spudcan under combined loading   总被引：1，自引：0，他引：1  
The bearing capacities of spudcan foundation under pure vertical (V),horizontal (H),moment (M) loading and the combined loading are studied based on a series of three-dimensional finite element analysis.The effects of embedment ratio and soil non-homogeneity on the bearing capacity are investigated in detail.The capacities of spudcan under different pure loading are expressed in non-dimensional bearing capacity factors,which are compared with published results.Ultimate limit states under combined loading are presented by failure envelopes,which are expressed in terms of dimensionless and normalized form in three-dimensional load space.The comparison between the presented failure envelopes and available published numerical results reveals that the size and shape of failure envelopes are dependent on the embedment ratio and the non-homogeneity of the soil.  相似文献   

3.
High energy dynamic compaction (HEDC) is adopted in a coastal reclamation area because the grain size of backfilled soil mostly ranges between 20 cm and 100 cm. The in situ tests for evaluating the effectiveness of HEDC were performed on the backfilled soil ground. The crater depth per drop and the whole test zone elevations before and after HEDC were measured and analyzed. Dynamic penetration tests and spectral analysis of surface wave (SASW) tests were used for investigating the improvement depth. Furthermore, the allowable bearing capacity of HEDC treated ground was determined based on the results of plate-load tests. It was found that HEDC did not cause the ground surface heave during construction, and was more effective than low energy dynamic compaction (LEDC) in terms of applied energy utilization. Based on the test results, the improvement depth of HEDC at this site was not less than 14 m, and there was no obvious weak layer within the range of improvement depth. The allowable bearing capacities were larger than 160 kPa. The investigation results indicate that the HEDC technique is an effective way for improving backfilled coarse-grained soil in coastal reclamation areas. This technique helps to achieve both greater improvement depths and higher ground bearing capacities as compared with LEDC.  相似文献   

4.
利用室内半模试验和颗粒流数值模拟,揭示多层砂土地基扩底桩单桩抗压承载特性及变形特征。结果表明,通过对比分析极限承载力与H_h/D(持力层厚度与扩大头直径之比)的关系可以看出,单桩的抗压极限承载力随H_h/D逐渐增加,当H_h/D超过2.0时,极限承载力基本不再增加,此时的单桩抗压极限承载力稳定在300.01~303.25 N,是H_h/D=0.5时极限承载力(183.83 N)的1.65倍。扩大头下部土体发生局部压缩-剪切破坏,破坏面从扩大头底面边缘向斜下方扩展,在水平方向影响范围达到最大后逐渐向桩内侧收缩;荷载作用越大,地基破坏区域越大,相应的极限抗压承载力也越大;持力层厚度增加,扩大头分担的荷载比例增大,分担的荷载达到稳定需要的桩顶位移也越大,H_h=0.5 D试验扩大头分担的荷载比例稳定时为60%,对应的桩顶位移约为29 mm;桩顶位移达到33 mm后,H_h=1.0~3.0 D试验稳定在63%~65%之间;通过细观颗粒流理论对砂土移动特性的研究发现,持力层厚度从0.5 D增大至2.0 D,破坏面的起始扩展角度从31°增大至42°。数值模拟研究结果与模型试验数据吻合效果良好,证明该方法分析多层砂土地基扩底桩单桩抗压荷载传递机理是可行的。  相似文献   

5.
Based on the geotechnical investigation data of artificial island at Dalian Offshore Airport, the spatial distribution of the physical and mechanical properties of deposit soils was statistically analyzed. The field investigation revealed that the deposit soils could be subdivided into three strata, i.e., the top marine deposit stratum, middle marine-continental deposit stratum, and deep continental deposit stratum. Field and laboratory test results demonstrated that the marine deposit soils had high water content (31.2% < wn < 63.10%), large void ratio (0.88 < e0 < 1.75), low permeability (kv < 10?6 cm/s), flow-plastic state (IL > 1), under consolidated (OCR < 1), high compressibility (Es < 4 MPa), low shear strength (11.7 kPa < cu < 43.7 kPa), and low bearing capacity (0 < fak < 120 kPa), they could not be used as natural foundation. The marine-continental and continental deposits were normally consolidated to over-consolidated (OCR ≥ 1), medium compressibility (4 MPa < Es < 20 MPa), high shear strength (29.7 kPa < cu < 73.7 kPa), and high bearing capacity (fak > 120 kPa). In addition, regression analysis results showed that the compression ratio was positively correlated with the natural water content, the coefficient of vertical consolidation was negatively correlated with the plasticity index, and the coefficient of vertical permeability was positively correlated with the initial void ratio. The results of the field and laboratory tests were synthesized to provide a basis for reclamation design.  相似文献   

6.
  相似文献   

7.
A centrifugal model test was performed for an embankment backfilled with lime-stabilized soil on an undisturbed marine clay foundation. During the test, in-flight photographs were captured, settlements were measured by displacement sensors, and displacement contours were obtained from the markers installed on the front face of the model foundation. These test data were analyzed and discussed in this paper. The test results show that the embankment was stable at 2 m height but ruptured during the loading from 2 to 4 m height. The ratio of the maximum horizontal displacement increment to the ground settlement increment at the embankment centerline suddenly increased during the loading from 4 to 6 m height, indicating the failure of the foundation. This result is in agreement with the observation of the centrifugal test and the calculated Terzaghi ultimate bearing capacity under an undrained condition. Considering the brittle behavior and low tensile strength of the lime-stabilized soil, it is recommended that the lime-stabilized soil should only be used for a low embankment with a height less than 2 meters.  相似文献   

8.
Piling procedure may disturb the surrounding soil, due to the installation particularly for cast-in-place piles. It causes a reduction in the soil strength parameters and, consequently, pile capacity. To overcome shortcomings and also for improving piles’ capacity, postgrouting as a compensation method is recognized and more developed in recent years. Helical piles, those are used widely in marine and land projects, although, are driven by torque implementation, but soil disturbance is noticed, where number of the helices become up to 3 and more. In this paper, an experimental study program is performed by frustum-confined vessel (FCV) to investigate bearing capacity of model helical piles and also postgrouted cases’ performance. FCV has been used because of its linear distribution of vertical and horizontal stresses from zero at top to maximum at bottom which simulates real field stress conditions. Through experimental study, small-scale helical model piles were made of 4-mm-thick steel plate and have been used with a length of 750?mm. The shaft and helix diameters of model piles have been 32 and 89?mm, respectively. So, the helix-to-shaft ratio (wing ratio) was about 2.8. The helical model piles installed in fine-grained sand as a surrounding soil and then axial loading tests before and after grouting were performed to achieve ultimate pile capacity. Results indicated postgrouting can improve both ratios of toe and frictional soil–pile interactions including upgrading β and Nt factors. In addition, the post grouting phenomena can change the pile geometry due to treated soil bond, resulting better functioning. Therefore, it is a proper method to improve helical piles performance and compensate installation effects in capacity mobilization.  相似文献   

9.
In this study, the dynamic response of pile foundation in dry sandy soil excited by two opposite rotary machines was considered experimentally. A small scale physical model was manufactured to accomplish the experimental work in the laboratory. The physical model consists of two small motors supplied with eccentric mass (0.012?kg) and eccentric distance (20?mm) representing the two opposite rotary machines, an aluminum shaft as the pile, and a steel plate a pile cap. The experimental work was achieved taking the following parameters into considerations: pile embedment depth ratio (L/d, where L is the pile length and d is its diameter) and operating frequency of the rotary machines. All tests were conducted in medium dense fine sandy soil with 60% relative density. Twelve tests were performed to measure the change in load transferred through the pile’s tip to the underlying soil. To predict precisely the dynamic load that will be induced from the rotary machines, a mini load cell with a capacity of 100?kg was mounted between the aluminum plate (the machine base) and the steel plate (pile cap). The results revealed that, before machine operation, the pile tip load was approximately equal to the static load (machine and pile cap), whereas during machines’ operation, the pile tip load decreased for all embedment depth ratios and operating frequencies. This reduction was due to the action of skin friction that was mobilized along the pile during operation, and as a result the factor of safety against pile bearing failure increases. For all operating frequencies and pile lengths, the factor of safety against bearing failure increased during machines’ operation, where the pile tip load became less than its value before starting operation. During operation, the skin friction resistance mobilized along pile length led to decrease the bearing load.  相似文献   

10.
螺旋桩芯劲性复合桩（helix stiffened cement mixing pile,简称HSCM桩）是一种新型复合桩,其成桩工艺会对桩身及其承载性能有较大影响。为验证HSCM桩在软黏土中同步旋进注浆工艺的可行性,并研究其成桩参数对抗压承载性能的影响,设计了2组缩尺模型试验,包括不同叶片数量与钻进速度的HSCM桩与对比螺旋桩。通过在高岭土制备的软黏土中成桩,并进行抗压承载性能及桩身几何尺寸测试,分析HSCM桩的成桩参数与水泥土桩身间的关系。试验结果表明：同步旋进注浆工艺能够在螺旋桩周围形成倒圆台状的水泥土桩身,水泥土桩身的平均黏结直径约为叶片直径的1.17～1.35倍;适当增加叶片数量能够使水泥与土体充分拌和,提高水泥土桩身的完整性与连续性,以改善HSCM桩的成桩质量;钻进速度大幅提高会导致注浆量不足,减小水泥土桩身的黏结直径与刚度;试验条件下HSCM桩的抗压极限承载力是螺旋桩的3.83～3.93倍,桩径扩大提高了侧摩阻力,注浆工艺加固并提高了土体强度,弥补了叶片在旋进过程中扰动土体造成强度降低的问题。  相似文献   

11.
The Yangshan deepwater port is the only container port built in the islands off the mainland of China. Batter piles with a sheet-pile-supported platform bulkhead structure were first used as a new shore-connecting structure to connect the front main wharf structure and the back land. Large-diameter sand columns were also used to reinforce the soft foundation of the shore-connecting structure in the deep water of the open sea. A 3D nonlinear FEM model based on real geological conditions was built to optimize the large-diameter sand columns’ reinforcing scheme and investigate shore-connecting structures’ mechanical properties under different construction conditions. The replacement ratio of 30%, the bottom elevation of the fourth soil layer, and the soft soil just below and directly adjacent to the shore-connecting structure were determined as optimal replacement ratio, reinforcing depths, and reinforcing area of the large-diameter sand columns reinforcement by assessing the force and deformation of the shore-connecting structure. By numerical computing, the maximum displacement of the supported platform was 11.03 cm, which was close to the measured value; and the piles’ maximum stress, displacement and moments were all smaller than the design strength. These indicated that the shore-connecting structure could remain stable by an optimal sand columns reinforcing scheme.  相似文献   

12.
Abstract

This article presents the performance of the short-term bearing capacity on soft clay soil treated by Kenaf geotextile under vertical loading via a small-scale modelling test at unit gravity. The ground model was formulated by consolidating kaolin in a rigid testing compartment. In the loading test, the strip footing was represented by a rigid footing. For the treated case, a series of tests were performed to examine the effects of the burial depth of the Kenaf geotextile on the bearing capacity of the soft soil. The Kenaf geotextile was laid beneath the rigid footing (at the ground surface) and at 50, 75 and 100?mm depth from the soil surface. All the measured results of the Kenaf geotextile treated ground were compared with the untreated ground. The incorporation of Kenaf fibre geotextile was observed to enhance the bearing capacity of soft cohesive clay up to 281% depending upon the depth of the installed geotextile. The geotextile at the surface provided the highest bearing capacity and sustained the highest displacement at failure. The outcome of this research will promote the use of natural fibre geotextiles as sustainable earth reinforcement in temporary earthwork applications.  相似文献   

13.
Jack-up platforms of the Ocean engineering structures always withstand the vertical gravity loads which are applied to the seabed by spudcan, so it is important to determine the bearing capacity and the penetration depth of the spudcan for its geometry. In fact, it is up to the deformation law and the failure modes of soil surrounding the spudcan which can calculate the ultimate bearing capacity of the spudcan foundation on the soil seabed. By using the finite element analysis software Abaqus, the deformation law of soil around the spudcan is analyzed in detail, and the failure modes of soil surrounding the spudcan foundation are achieved. At the same time, based on the limit equilibrium theory, by use of static permissible slip-line field, the ultimate bearing capacity of the spudcan foundation is analyzed and the lower limit solution is derived theoretically, and the effect of the spudcan angle on the ultimate bearing capacity is investigated. The numerical results are compared with those obtained by the theoretical formulas deduced in this paper. On the basis of the lower limit solutions in this paper, the effect of the spudcan angle on the ultimate bearing capacity is revealed, and a practical bearing capacity formula is given to take the effect of the spudcan angle into consideration.  相似文献   

14.
This paper presents a case study of dynamic compaction (DC) on backfill ground for planned oil tanks located at Nanjing Bay. The ultra-high energy DC level of 18,000 kN · m was applied in the area tamping phase of the dynamic compaction. In combination with ground replacement technique by forcing crushed stones into the underlain cohesive layer, the high-compressibility of this layer was properly tackled. The construction techniques and ground improvement mechanisms are introduced and discussed. Field evaluations before and after the dynamic compaction, including surface wave test, plate load test, and soil sampling, showed that the ultra-high energy dynamic compaction in combination with ground replacement achieved much greater improvement depth and ground bearing capacity than conventional DC. Results show that dynamic compaction of 18,000 kN · m combined with ground replacement is of great merit in dealing with backfill ground with weak cohesive content in harbor development.  相似文献   

15.
Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results.  相似文献   

16.
Abstract

The performance of steel caisson during and after installation with different penetration velocities in medium dense sand is presented. The applied jacking forces, the amount of formed soil heave and bearing capacity were measured in the model tests. The influence of penetration velocities on jacking forces, soil heave and bearing capacity were also discussed in detail. The results indicated that the jacking forces for caisson in medium dense sands were significantly affected by the penetration velocity. The larger the penetration velocity, the more soil flowed into the caisson cavity during installation. This will lead to larger inner shaft resistance and in turn more jacking forces required for the same penetration depth. The height of soil heave during installation increases with penetration velocity. The m value calculated by the ratio of the volumes of the soil heave to that of the penetrated caisson wall can be used to evaluate the soil heave. The larger the applied velocity, the larger the m value and larger bearing capacity of caisson after installation. The relationship between the m value and penetration velocity can be used to control the soil heave for a steel caisson with a wall thickness to external diameter ratio of 4.2% in medium dense sand by jacking method.  相似文献   

17.
Suction buckets are a promising foundation solution for offshore wind energy systems. The bearing behavior of monopod buckets under drained monotonic loading in very dense and medium dense sand is investigated in this study by means of numerical simulation with the finite element method. Special focus is given to the ultimate capacity and the initial stiffness of the bucket-soil foundation system. The numerical model is validated by comparison with field test results. The bearing behavior of the structure is explained through an evaluation of a reference system. It is shown that the bucket experiences a heave during horizontal loading, which leads to the formation of a gap between the bucket lid and the soil with increasing load. At large loads and rotations close to failure of the system there is no contact between lid and soil, and the whole load is transferred to the soil via the bucket skirt. A parametric study shows how the ultimate capacity and initial stiffness of the system depend on the bucket dimensions and loading conditions, i.e. load eccentricity. Normalized equations for ultimate capacity and initial stiffness are derived from the numerical simulation results, which can be used in the scope of a preliminary design for buckets in sand.  相似文献   

18.
Semi-deep skirted foundations are now considered to be a viable foundation option for a variety of onshore and offshore applications. The capacity under combined vertical, horizontal, and moment loadings must be found to ensure their capability and stability. In this study, undrained bearing capacity subjected to vertical loading, as part of combined loading is determined through stress characteristics and finite element analyses. Circular skirted foundations with different soil strength and geometries considering embedment depth effects have been studied. Stress field, kinematic mechanism accompanying failure, and bearing capacity factors for various embedment ratios are investigated. Acquired vertical failure mechanism has demonstrated the transition from a general shear to a punch shear failure. Comparisons with different research works including conventional methods, upper and lower bound, finite element analyses, physical modeling, experimental, and centrifuge tests have indicated the underestimation of conventional approaches and accuracy of proposed methods in determining bearing capacity. Furthermore, differences between predicted bearing capacities and the results of this study increased with D/B ratio due to ignoring the significant role of skin friction in larger embedment circumference.  相似文献   

19.
Considering the current disadvantages of present offshore wind turbine foundations, a novel anchor foundation with skirt and branches is proposed, called offshore umbrella suction anchor foundation (USAF). A series of experiments and numerical simulations were performed to explore the bearing capacity of the USAF under various kinds of loading modes. The bearing characteristics and the anchor–soil interactions are described in detail for horizontal static loading, horizontal cyclic loading, and an antidrawing (pullout) test in silty soil. In the static loading test, the load–deflection of the anchor under step loading was analyzed and the normalized curve of the load–deflection was obtained to determine the ultimate horizontal bearing capacity of the anchor under normal working conditions. Under horizontal cyclic loading, the relationship between the plastic cumulative deformation and cyclic number was determined. In addition, the responses of USAF were investigated for a low wave frequency and storm surges. In the drawing test, it was found that a “segmentation phenomenon” occurred during the test. Moreover, a method to identify the maximum antidrawing load of USAF was provided based on dynamic mechanics. The numerical results show that the use of anchor branches and skirt can enhance the bearing performance of USAF to a certain degree. However, the anchor branch has a slight positive influence on the bearing performance improvement. The USAF is not only similar to a stiff short pile, but a rotation occurs. The failure envelope under composite loading (V-M) was obtained and the changes associated with changes in the aspect ratio of the internal compartment were clarified.  相似文献   

20.
The low side friction of piles in coral sand results in the low bearing capacity of foundations. In this paper, expansive concrete pile is utilized to improve the bearing capacity of pile foundations in coral sand. Both model tests and numerical simulation are performed to reveal the bearing mechanism of expansive concrete pile in coral sand.Results showed that the lateral earth pressure near pile increases obviously and the side friction of piles is improved,after adding expansion agent to the concrete. The horizontal linear expansion is 1.11% and the bearing capacity increased 41% for the pile, when 25% expansion agent is added. Results in finite element numerical simulation also show that ultimate bearing capacity increases with the increase of the linear expansion ratio. Besides, the area for obvious increase in side friction is below the surface of soil about three times the pile diameter, and the expansion leads to a high side friction sharing of the pile. Therefore, the cast-in-place expansive concrete pile is effective in improving the bearing capacity of piles in coral sand.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号