共查询到19条相似文献，搜索用时 156 毫秒
1.
自升式钻井平台插桩是地基土在桩靴荷载作用下发生连续的塑性破坏的动态过程,当地基极限承载力等于桩靴荷载时插桩完成。经典土力学极限承载力理论对土体潜在滑动面做了假设,无法有效分析土体内部的破坏过程。本研究应用有限元法（FEM ）对插桩过程进行了模拟,得到地基土的破坏机制以及中间荷载下土体的应力、应变情况,通过和各理论公式计算的极限承载力进行对比分析,分析影响地基极限承载力的因素。研究表明,基础宽度与硬土层厚度的比值 B/H越大,下卧软土层越容易发生塑性破坏,极限承载力明显下降,当B/H＜0．286时,可以忽略下卧软土层对地基承载力的影响。 相似文献
2.
利用砂土中扩底抗拔桩的模型试验,研究从开始加载到破坏时扩底抗拔桩地基动态变形全过程的承载特性。试验结果表明:半模试验得到的极限荷载和破坏面均略小于全模试验结果,采用半模试验测量地基变形过程与破坏模式有明显优势,用半模试验代替全模试验是可行的;随着桩顶荷载的增加,扩大头上方的土体由压缩变形逐渐发展为局部的压缩—剪切破坏;扩大头对其上部的桩侧摩阻力有增强作用,对其下部的桩侧摩阻力有削弱作用;扩大头在工作荷载、极限荷载和破坏荷载作用时分担的荷载比例为15%~20%。 相似文献
3.
4.
变截面劲性水泥土桩承载特性室内模型试验研究 总被引：1，自引：0，他引：1
研究变截面劲性水泥土桩的几何特征对承载特性的影响,结果表明:具有1个扩大盘或2个扩大盘间距较大的变截面桩,盘下部的土体发生压缩和局部剪切破坏现象,上部的土体则发生梨形滑落;盘间距较小时,上下两盘之间的土体与两盘成为一体;变截面桩的桩侧荷载分担值均远大于桩端荷载分担值,盘的数量及间距对桩侧及桩端荷载分担值影响不大;1个盘时,其位置对承载力有一定的影响;2个等间距盘的变截面桩,盘位置越高承载力越高;盘间距对承载力影响不显著;3个盘的承载力大于2个盘的承载力,但结果相差不大;变截面桩的承载力得到显著提高,其承载力不小于与扩大盘直径相等的等截面桩;随着桩顶荷载的增大,盘承担的荷载增加显著,盘以下桩身的轴力因盘承担大部分而骤减,其降低幅度与盘的数量、位置及间距有关. 相似文献
5.
离岸深水全直桩码头承载性能有限元分析 总被引：1，自引：0，他引：1
全直桩码头是适于软土地基上离岸深水海域的新型高桩码头结构型式,其承载机理与传统高桩码头存在较大差异,且软土地基循环软化效应显著。建立全直桩码头结构与地基相互作用三维弹塑性有限元模型,基于二次开发采用拟静力法对土体循环软化效应进行模拟。通过有限元模型研究全直桩码头的承载特性与破坏模式,并探讨水平极限承载力的影响因素。研究表明水平荷载作用下,基桩的塑性破坏是结构失稳的控制因素,地基土体的承载力对结构水平极限承载力不起决定性作用;竖向荷载作用下,结构竖向极限承载力由地基土体强度决定。研究范围内入土深度对结构水平极限承载力影响不大,但桩壁厚度减小或考虑土体软化后,结构水平极限承载力明显降低。设计中,增加入土深度可有效减小土体软化引起的水平极限承载力降低程度,且应考虑结构腐蚀和土体软化对水平极限承载力的双重降低效应,为钢管桩预留足够的腐蚀富裕量。 相似文献
6.
API规范推荐的p-y曲线是由均质土体得到的,并未考虑土层间相互作用,Georgiadis基于柔性桩提出了等效深度法修正p-y曲线,把均质土p-y曲线延伸到了成层土体中。为了研究p-y曲线和等效深度法对于大直径单桩在成层土体中的适用性,取4种典型地质条件:成层砂土、砂土-黏土-砂土、成层黏土和黏土-砂土-黏土,通过L-PILE软件计算了6 m直径单桩基础的p-y曲线、桩顶水平荷载-位移曲线、桩身位移和弯矩。并与ABAQUS建立的单桩基础三维有限元模型计算结果进行比较。结果表明等效深度法对于成层砂土影响不大;对于成层黏土影响较大;对于中间为软弱土层的成层土体,在荷载较大时影响显著,等效深度法计算结果更加接近FEM结果。在成层土体中,p-y曲线应用于大直径单桩对于砂土高估了初始刚度,低估了极限抗力;对于黏土则低估了初始刚度和极限抗力。 相似文献
7.
为研究钻井船插桩对邻近平台群桩相互作用的影响,采用耦合欧拉拉格朗日(CEL)方法对桩靴贯入黏土层时邻近群桩中各桩荷载分担比、桩头附加位移及两桩相互作用系数进行了分析。首先通过对缩尺模型试验的数值分析,验证了CEL方法的可行性;然后进一步分析了桩靴贯入黏土层时对邻近群桩相互作用的影响;最后探讨了净间距、桩间距对群桩相互作用的影响。结果表明,在桩靴贯入中,前桩的荷载分担比大于后桩,且桩靴贯入至一定深度后,当净间距越小或桩间距越大时,前桩的荷载分担比越大、后桩的荷载分担比越小,但各桩的荷载分担比随桩靴贯入深度增加时的变化规律不变;净间距越大,桩头附加位移及相互作用系数越小;在桩靴贯入时,由于受群桩遮拦效应的影响,桩头附加位移及相互作用系数随桩间距的变化规律同插桩前有所不同,当桩间距大于3倍桩径时,随桩间距的增加而减小,当桩间距小于3倍桩径时,随桩间距的增加而增大。 相似文献
8.
为改善海上风电大直径钢管桩的水平承载性能,基于ABAQUS有限元软件对单桩改进形式的加翼桩结构进行了系统研究,计算分析了软黏土地基中加翼桩在水平荷载作用下桩身弯矩、应力、位移、桩身泥面处倾斜率和极限承载力,研究了加翼桩面积、形状、埋深和刚度等翼板参数对加翼桩水平承载性能的影响规律,根据加翼桩的桩-土作用机理,参考现行规范模式提出适用于软黏土地基大直径钢管桩的P-Y曲线。研究结果表明,加翼桩通过在泥面处设置翼板可降低桩基泥面处倾斜率50%、提高桩基极限承载力60%以上,加翼桩水平承载性能明显优于单桩。 相似文献
9.
10.
工程中常涉及到地基承载力特征值fa及桩端阻力qpa,作为同量纲的地基指标,对同一土层后者往往要比前者高得多。运用梅耶霍夫地基极限承载力理论,分析了随基础埋深的加大地基土破坏形式的变化,对浅基础及桩基础破坏形式、地基承载力特征值fa与桩端承载力特征值qpa作了对比。研究结果将有利于建立及区别地基承载力特征值及桩端端阻力特征值的物理概念,对实际工程具有指导意义。 相似文献
11.
Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results. 相似文献
12.
《中国海洋工程》2021,(3)
The low side friction of piles in coral sand results in the low bearing capacity of foundations. In this paper, expansive concrete pile is utilized to improve the bearing capacity of pile foundations in coral sand. Both model tests and numerical simulation are performed to reveal the bearing mechanism of expansive concrete pile in coral sand.Results showed that the lateral earth pressure near pile increases obviously and the side friction of piles is improved,after adding expansion agent to the concrete. The horizontal linear expansion is 1.11% and the bearing capacity increased 41% for the pile, when 25% expansion agent is added. Results in finite element numerical simulation also show that ultimate bearing capacity increases with the increase of the linear expansion ratio. Besides, the area for obvious increase in side friction is below the surface of soil about three times the pile diameter, and the expansion leads to a high side friction sharing of the pile. Therefore, the cast-in-place expansive concrete pile is effective in improving the bearing capacity of piles in coral sand. 相似文献
13.
For the static pressure pile, the most important is to determine the standard value of ultimate bearing capacity of single pile. At present, the bearing capacity of pile foundation is usually determined by the cone penetration test (CPT) test. The empirical formula was used in practice, but the effect of excess pore water pressure generated in the penetration on the measured cone-tip resistance and side friction is neglected. In this study, based on the field test results at Fengyu playground at Yancheng Institute of Technology by CPT and CPTU methods, the bearing capacity of pile was predicted by the standardized methods, the LCPC (France method) and CPTU direct prediction methods. The prediction was also compared with the results by the static load test method. The prediction accuracy of the CPTU method was then discussed as well. The results reveal that the accuracy of the CPTU method was the highest, which was consistent with the results obtained by the static load test method. It is the best method and worthy of being applied for predicting bearing capacity of piles in engineering applications. 相似文献
14.
Vertical uplift static loading tests of single model pile were conducted in the in-lab calcareous sand and quartz sand by emulating practical condition of full-size piles in site. The settlement, lateral deflection, axial force, and friction distribution of the pile are analyzed for each physical test. The pile behaviors in calcareous sand and quartz sand are compared. From the test results, it can be found that the pile top displacement of uplift pile in calcareous sand can be divided into two stages: the pile–sand synchronous stage and pile–sand asynchronous (relative displacement) stage. Data from uplift tests show that the heave of calcareous sand around pile top is very small, which is resulted from the mutually restraint of surface particle. The mutual restriction of surface particle leads to “bottleneck effect” and strengthens ultimate side friction of upper pile segment. In addition, the shear dilatancy and particle breakage of calcareous sand lead to the upper harden and the lower soften of side friction, respectively. Cases of calcareous sand and quartz sand show different responses to pile forming methods, which due to the sands’ different characteristics of particle breakage when compressed as well as plastic deformation under loading–unloading conditions. 相似文献
15.
桩-筒组合基础是将单桩基础与筒型基础组合的一种新型海上风电基础形式,其受力模式不同于传统桩基基础,优点是可通过合理减小桩长、桩壁厚等途径提高承载性能。基于极限地基反力法,提出单层黏土中桩-筒组合基础受力模式及水平承载力的计算方法。利用力加载和位移加载两种控制方法进行数值分析,研究水平承载性能的影响因素。结果表明,在一定范围内,桩-筒组合基础水平承载性能随桩入土深度、桩壁厚、筒外径的增大而提高。基于实际工程,对等用钢量的单桩基础与组合基础进行比较计算,结果表明,桩-筒组合基础可有效降低基础倾斜度和位移,提高承载性能。 相似文献
16.
AbstractPile foundation is the most popular option for the foundation of offshore wind turbines. The degradation of stiffness and bearing capacity of pile foundation induced by cyclic loading will be harmful for structure safety. In this article, a modified undrained elastic–plastic model considering the cyclic degradation of clay soil is proposed, and a simplified calculation method (SCM) based on shear displacement method is presented to calculate the axial degradated capacity of a single pile foundation for offshore wind turbines resisting cyclic loadings. The conception of plastic zone thickness Rp is introduced to obtain the function between accumulated plastic strain and displacement of soil around pile side. The axial ultimate capacity of single piles under axial cyclic loading calculated by this simplified analysis have a good consistency with the results from the finite element analysis, which verifies the accuracy and reliability of this method. As an instance, the behavior of pile foundation of an offshore wind farm under cyclic load is studied using the proposed numerical method and SCM. This simplified method may provide valuable reference for engineering design. 相似文献
17.
Amirhossein Mohammadi Abolfazl Eslami Sjoerd E. A. T. M. van der Zee 《Marine Georesources & Geotechnology》2013,31(2):164-179
ABSTRACTOil and its derivatives contaminate many soils and not only affect their chemical and biological properties but also their geotechnical properties. As oil contamination may deteriorate the functioning of piles, this paper addresses the effects of oil contamination on soil–pile interactions. Axial compressive bearing capacities of two close-ended, instrumented piles were investigated in different oil-contaminated sand using frustum confining vessel. Three different oils (gasoil, crude oil, and used motor oil) at different contamination levels were considered and using some strain gauges, the toe, shaft, and the net total bearing capacity of piles, as well as load distributions along the pile length, were derived. The results show that the presence of oil between soil particles has considerable adverse effects on bearing capacities of model piles, especially the shaft bearing capacity. The oil viscosity and percentage, as well as the contaminated sand bed thickness around the piles, are the most influential parameters. The higher the oil viscosity and oil content, the lower the values of the piles’ bearing capacities in comparison to the uncontaminated sand. With some modifications on the bearing capacity parameters of CFEM method, a good agreement was observed between measured and calculated bearing capacity values. 相似文献
18.
近海海床表层多为软黏土或淤泥质土,为探究海床表层软土对海上风电宽浅式筒型基础承载特性的影响,以中国广东某海域风电场为背景,通过有限元分析的方法,研究竖向、水平、弯矩荷载作用下软土层厚度和土体强度对基础极限承载力、破坏模式以及筒基土压力分布的影响。研究结果表明:当软土层厚度小于H/2(H为筒裙高度)时,单向荷载作用下宽浅式筒型基础极限承载力随软土层厚度的增加呈线性减小的趋势;当软土层厚度大于H/2后,承载力降低速率逐渐增大。表层软土的存在,使得塑性区范围缩小,软土层内土体塑性破坏更加明显。竖向荷载作用下,随软土层厚度的增大,筒顶承载先减小后增大,筒内侧摩阻力先增大后减小;水平荷载和弯矩作用下,筒侧被动土压力的降低是引起软土覆盖地基中基础承载能力降低的主要因素。 相似文献
19.
Jia-jin Zhou Kui-Hua Wang Ri-Hong Zhang Tian-Long Yan 《Marine Georesources & Geotechnology》2016,34(3):293-301
A static drill rooted nodular pile is a new type of composite pile foundation with high bearing capacity, and mud emissions can be largely reduced using the static drill rooted method. This report presents a model test on the behavior of this composite pile in a test box. The load-displacement response, axial force, skin friction, and mobilized base load are discussed in the report; in particular, the force in the cemented soil was investigated based on the measured data. Moreover, the finite element software ABAQUS was used to help investigate this behavior more thoroughly. It was determined that the function of the cemented soil around the pile shaft was different from that at the enlarged pile base; the stress in the cemented soil around the shaft increased suddenly when nearing the pile base; the ultimate skin friction obtained in the model test was larger than that estimated in the field test; and the relative displacement between the precast nodular pile and the cemented soil could be ignored during the loading process, which corresponded to the result of the field test and demonstrated that the nodular pile and cemented soil act as one entity during the loading process. 相似文献