共查询到20条相似文献，搜索用时 15 毫秒
1.
建立双臂起重船从运输船上起吊大型稳桩施工平台的吊装系统模型,其中,起重船与运输船呈T型布置。首先基于势流理论,采用专业水动力分析软件AQWA开展了双船系统的频域水动力分析,分析双船起吊系统的水动力干扰特性和遮蔽效应,并对双船间隙自由液面进行黏性修正从而提高频域多体水动力分析的精度。进一步采用频域—时域方法对起吊耦合系统进行参数分析,探究起吊速度、波浪周期等对吊索张力和起重船运动的影响规律。分析多个工况下运输船的遮蔽效应对起吊系统的影响。结果表明,对间隙流体施加阻尼自由液面边界条件可以一定程度提高计算模型的精度,在某些周期的迎浪条件下运输船对起重船的遮蔽效应可以降低吊装系统的响应;起吊速度对时域动力响应的影响较小;周期为8 s的规则波引起过大的动力响应。 相似文献
2.
This paper is concerned with the formation control problem of multiple underactuated surface vessels moving in a leader-follower formation.The formation is achieved by the follower to track a virtual target defined relative to the leader.A robust adaptive target tracking law is proposed by using neural network and backstepping techniques.The advantage of the proposed control scheme is that the uncertain nonlinear dynamics caused by Coriolis/centripetal forces,nonlinear damping,unmodeled hydrodynamics and disturbances from the environment can be compensated by on line learning.Based on Lyapunov analysis,the proposed controller guarantees the tracking errors converge to a small neighborhood of the origin.Simulation results demonstrate the effectiveness of the control strategy. 相似文献
3.
This study investigates the coupling effects of six degrees of freedom in ship motion with fluid oscillation inside a three-dimensional rectangular container using a novel time domain simulation scheme. During the time marching, the tank-sloshing algorithm is coupled with the vessel-motion algorithm so that the influence of tank sloshing on vessel motions and vice versa can be assessed. Several factors influencing the dynamic behavior of tank–liquid system due to moving ship are also investigated. These factors include container parameters, environmental settings such as the significant wave height, current velocity as well as the direction of wind, wave and flow current acting on the ship. The nonlinear sloshing is studied using a finite element model whereas nonlinear ship motion is simulated using a hybrid marine control system. Computed roll response is compared with the existing results, showing fair agreement. Although the two hull forms and the sea states are not identical, the numerical result shows the same trend of the roll motion when the anti-rolling tanks are considered. Thus, the numerical approach presented in this paper is expected to be very useful and realistic in evaluating the coupling effects of nonlinear sloshing and 6-DOF ship motion. 相似文献
4.
Seakeeping of two ships in close proximity 总被引：1，自引：0，他引：1
Underway replenishment is an essential component of long-term naval operations. During underway replenishment, two ships travel in close proximity at moderate forward speed. This paper examines the hydrodynamic interactions that can influence seakeeping during such operations. Presented numerical predictions include the influence of interaction effects on hydrodynamic forces for two ships in waves. A scarcity of validation material for numerical predictions prompted new towing tank experiments for two ships in waves. The experiments used semi-captive models, and the numerical code was modified to include restraining forces for specified modes. The numerical predictions and experiments show that the presence of a larger ship can significantly influence the motions of a smaller ship in close proximity. 相似文献
5.
This paper presents a potential based boundary element method for solving a nonlinear free surface flow problem for a ship moving with a uniform speed in finite depth of water. The free surface boundary condition is linearized by the systematic method of perturbation in terms of a small parameter up to third order. The surfaces are discretized into flat quadrilateral elements and the influence coefficients are calculated by Morino's analytical formula. Dawson's upstream finite difference operator is used in order to satisfy the radiation condition. The second order solution gives better result than the first or third order solution. So the present method with the second order solution can be adopted as a powerful tool for the hydrodynamic analysis of the thin ship in finite depth of water. 相似文献
6.
Robust path-following of underactuated ships: Theory and experiments on a model ship 总被引：1，自引：0，他引：1
A method is proposed to design a new global controller that forces an underactuated ship to follow a reference path under disturbances induced by wave, wind and ocean-current. The controller is designed such that the ship moves on the path with an adjustable forward speed and its total velocity is tangential to the path. The ship under consideration is not actuated in the sway axis, and the mass and damping matrices are not assumed to be diagonal. Nonlinear damping terms are also included to cover both low- and high-speed applications. The new result is facilitated by choosing an appropriate origin of the body-fixed frame, designing a suitable filter of sway velocity, several nonlinear coordinate changes, the backstepping technique, and utilizing the ship dynamic structure. Experimental results on a model ship illustrate the effectiveness of the proposed method. 相似文献
7.
8.
Parabolic Approximation of the Weakly Nonlinear Mild Slope Equation with Bottom Friction 总被引：2，自引：0，他引：2
This paper presents a refined parabolic approximation model of the mild slope equation to simu-late the combination of water wave refraction and diffraction in the large coastal region.The bottom frictionand weakly nonlinear term are included in the model.The difference equation is established with the Crank-Nicolson scheme.The numerical test shows that some numerical prediction results will be inaccurate in com-plicated topography without considering weak nonlinearity;the bottom friction will make wave height damp-ing and it can not be neglected for calculation of wave field in large areas. 相似文献
9.
A coupled numerical model considering nonlinear sloshing flows and the linear ship motions has been developed based on a boundary element method. Hydrodynamic performances of a tank containing internal fluid under regular wave excitations in sway are investigated by the present time-domain simulation model and comparative model tests. The numerical model features well the hydrodynamic performance of a tank and its internal sloshing flows obtained from the experiments. In particular, the numerical simulations of the strong nonlinear sloshing flows at the natural frequency have been validated. The influence of the excitation wave height and wave frequency on ship motions and internal sloshing has been investigated. The magnitude of the internal sloshing increases nonlinearly as the wave excitation increases. It is observed that the asymmetry of the internal sloshing relative to still water surface becomes more pronounced at higher wave excitation. The internal sloshing-induced wave elevation is found to be amplitude-modulated. The frequency of the amplitude modulation envelope is determined by the difference between the incident wave frequency and the natural frequency of the internal sloshing. Furthermore, the coupling mechanism between ship motions and internal sloshing is discussed. 相似文献
10.
M. Taylan 《Ocean Engineering》1999,26(11):255
Mathematical modeling of the nonlinear roll motion of ships is one subject widely dealt with in nonlinear ship dynamics. This paper investigates setting up a form of nonlinear roll motion model and developing its periodic solution by the generalized Krylov–Bogoliubov asymptotic method in the time domain. In this model, nonlinearities are introduced through damping and restoring terms. The restoring term is approximated as a third-order odd polynomial whereas the quadratic term is favored to represent the nonlinear damping. The ship is assumed to be under the influence of a sinusoidal exciting force. Although the method is expressible to contain any order of the perturbing term, a single degree is chosen to avoid cumbersome mathematical complexity. In order to improve the solution a first-order correction term is also included. Moreover, a numerical example is carried out for a small vessel in order to validate the solution scheme. 相似文献
11.
S. Sutulo 《Ocean Engineering》2010,37(10):947-958
The method of boundary integral equation developed by the authors was applied for computing inertial and damping characteristics of ship sections for the cases of multi-stepped and inclined bottoms. Comparative calculations for three typical ship hull sections were performed and analyzed. The frequency-dependent data computed for these ship sections can be used to assess the bottom geometry's influence onto the ship motions in waves by means of the strip theory. Limiting values of the same characteristics corresponding to the close-to-zero frequency can also be used for estimation of hydrodynamic forces in manoeuvring over shallow and confined waterways. 相似文献
12.
A time-domain analysis is used to predict wave loading and motion responses for a ship traveling at a constant speed in regular oblique waves. Considered as a distribution of normal velocities on the wetted hull surface, the combined diffraction and radiation perturbations caused by the forward moving ship and her motions are determined simultaneously. This way, the ship-hull boundary condition is exactly fulfilled. The 3-D time domain Green's function is used to express the combined diffraction/radiation potential in terms of impulsive and memory potentials. Application of the Bernoulli equation yields the pressure distribution and accordingly, the necessary hydrodynamic forces. The equations of motion of the ship are then developed and solved in the time domain.Forces and motions at forward speed are predicted for a Wigley ship-hull in head waves and for a catamaran-ferry in oblique waves. Comparison is made with published theoretical and experimental results for the Wigley ship-hull, and the agreement is good. For the catamaran, a self-propelled model is built and tested both in a large towing tank and in a seakeeping basin in order to measure the six-degrees-of-freedom forces, moments and motions at forward speed in regular waves of different directions. For the longitudinal motions, the agreement between measurements and predictions is generally good. For the transverse motions, however, acceptable discrepancy exists. The discrepancy is thought to be mainly due to the exclusion from the analysis of the rudder forces and viscous damping. The inclusion of such nonlinear effects in the time domain simulation involves complex analysis and this problem is left to a future research. 相似文献
13.
This work presents an application of stochastic inverse method for the determination of nonlinear roll damping moment of a ship at zero forward speed. Nonlinear roll damping moment was estimated from the measured dynamic responses through stochastic inverse model. It is shown that this method enables nonlinear characteristic of the roll damping to be estimated without any assumption on its form of nonlinearity, including its confidence intervals given noisy data. The accuracy and practicability were assessed with laboratory tests related to both free-decay and forced rolling motions. The estimation results of the nonlinear damping moment show good agreement in all cases. 相似文献
14.
The coupling and interactions between ship motion and inner-tank sloshing are investigated by a time-domain simulation scheme. For the time-domain simulation, the hydrodynamic coefficients and wave forces are obtained by a potential-thoery-based three-dimensional (3D) diffraction/radiation panel program in frequency domain. Then, the corresponding simulations of motions in time domain are carried out using convolution integral. The liquid sloshing in a tank is simulated in time domain by a Navier–Stokes solver. A finite difference method with SURF scheme is applied for the direct simulation of liquid sloshing. The computed sloshing force and moment are then applied as external excitations to the ship motion. The calculated ship motion is in turn inputted as the excitation for liquid sloshing, which is repeated for the ensuing time steps. For comparison, we independently developed a coupling scheme in the frequency domain using a sloshing code based on the linear potential theory. The hydrodynamic coefficients of the inner tanks are also obtained by a 3D panel program. The developed schemes are applied to a barge-type FPSO hull equipped with two partially filled tanks. The time-domain simulation results show similar trend when compared with MARIN's experimental results. The most pronounced coupling effects are the shift or split of peak-motion frequencies. It is also found that the pattern of coupling effects between vessel motion and liquid sloshing appreciably changes with filling level. The independent frequency-domain coupled analysis also shows the observed phenomena. 相似文献
15.
System identification provides an effective way to predict the ship manoeuvrability. In this paper several measures are proposed to diminish the parameter drift in the parametric identification of ship manoeuvring models. The drift of linear hydrodynamic coefficients can be accounted for from the point of view of dynamic cancellation, while the drift of nonlinear hydrodynamic coefficients is explained from the point of view of regression analysis. To diminish the parameter drift, reconstruction of the samples and modification of the mathematical model of ship manoeuvring motion are carried out. Difference method and the method of additional excitation are proposed to reconstruct the samples. Using correlation analysis, the structure of a manoeuvring model is simplified. Combined with the measures proposed, support vector machines based identification is employed to determine the hydrodynamic coefficients in a modified Abkowitz model. Experimental data from the free-running model tests of a KVLCC2 ship are analyzed and the hydrodynamic coefficients are identified. Based on the regressive model, simulation of manoeuvres is conducted. Comparison between the simulation results and the experimental results demonstrates the validity of the proposed measures. 相似文献
16.
In this paper, using a second-order steady-state approach and a three-dimensional (3D) pulsating source distribution method derives the nonlinear hydrodynamic forces on a ship advancing in waves. The nonlinear hydrodynamic forces considered here consist of the mean lateral drifting force and the added resistance, which can be expressed as products of the ship-motion responses, the radiation potential, diffraction potential and the incident-wave potential. All related velocity potentials applied in the calculations are in 3D form. The Series 60 and Marine ship hulls are used for numerical calculations and the results are compared with existing experimental data and two-dimensional (2D) solutions. The comparisons show that the results obtained in the paper generally agree with experimental data well. It is also found that the nonlinear hydrodynamic forces obtained based on the present 3D source distribution methods are indeed improved in some calculations compared with the 2D method, especially for the mean lateral drifting force. 相似文献
17.
The paper studies the parametric stochastic roll motion in the random waves. The differential equation of the ship parametric roll under random wave is established with considering the nonlinear damping and ship speed. Random sea surface is treated as a narrow-band stochastic process, and the stochastic parametric excitation is studied based on the effective wave theory. The nonlinear restored arm function obtained from the numerical simulation is expressed as the approximate analytic function. By using the stochastic averaging method, the differential equation of motion is transformed into Ito's stochastic differential equation. The steady-state probability density function of roll motion is obtained, and the results are validated with the numerical simulation and model test. 相似文献
18.
The 6 degrees of freedom (DOF) model with a high degree of complexity for capturing ship dynamics is generally able to track the nonlinear and coupling dynamics of ships. However, the 6 DOF model makes challenges in estimating model coefficients and designing the model-based control. Therefore, simplified ship dynamic models within allowed accuracy are essential. This paper simplified the 6 DOF nonlinear dynamic model of ships into two decoupled models including the speed model and the steering model through reasonable assumptions. Those models were tested through maneuvering simulations of a container ship with a 4 DOF dynamic model. Support vector machines (SVM) optimized by the artificial bee colony algorithm (ABC) was used to identify parameters of speed and steering models by analyzing the rudder angle, propeller shaft speed, surge and sway velocities, and yaw rate from simulated data extracted from a series of maneuvers made by the container ship. Comparisons with the first order linear and nonlinear Nomoto models show that the simplified nonlinear steering model can capture more complicated dynamics and performs better. Additionally, comparisons among three different parameter identification methods demonstrate similar identification results but the different performance involving the applicability and effectiveness. SVM optimized by ABC is relatively convenient and effective for parameter identification of ship simplified dynamic models. 相似文献
19.
S. A. Ermakov I. A. Kapustin O. V. Shomina 《Izvestiya Atmospheric and Oceanic Physics》2014,50(2):204-212
Investigation of damping of gravity-capillary waves (GCWs) in the presence of turbulence is a classical hydrodynamic problem which has important geophysical applications, one of which is related with the problem of forming a radar and optical image of a ship wake on wavy water surface. In this work a new method for the laboratory study of surface wave damping in turbulized liquid is described and the results are presented. The damping of standing GCWs by turbulence on the water surface in a tank mounted on a vibration table is studied. GCWs and turbulence are excited using a two-frequency mode of vibration table oscillations. A high-frequency small amplitude signal is used for parametric GCW excitation; a low-frequency large amplitude signal is used for generating turbulence due to water flowing through a fixed perforated grid submerged into the tank. The coefficient of GCW damping is determined by measured threshold of parametric excitation of the waves; turbulence characteristics are determined by the PIV and PTV techniques. Dependences of GCW damping coefficients on their frequency at different turbulence intensities are obtained, estimates for turbulent viscosity are presented, and a comparison with empirical models proposed earlier is performed. 相似文献
20.
As known, the rolling motion characteristics, amplitudes and accelerations, greatly influence the ability of a ship to operate and survive in bad weather. On the other hand, traditional computer codes for seakeeping calculations fail the forecasting of large amplitude rolling. There is a great need of using semi-empirical damping models and coefficients. This stresses the importance of campaigns of measurements as described in the paper, to get a deeper insight into the physical-mathematical modelling of the different contributions to rolling equation.Experimental tests on nonlinear rolling in a regular beam sea of a Ro-Ro ship model have been conducted by varying both the wave steepness and the wave frequency. The use of a parameter estimation technique, based on the least squares fitting of the stationary numerical solution of the nonlinear rolling motion differential equation, allowed to obtain informations on the damping model and on the linear and nonlinear damping coefficients. These exhibit a quite strong dependence on frequency that reduces the efficiency of constant coefficients rolling equation to simulate large amplitude nonlinear rolling. The results indicate that a good quality prediction model of nonlinear rolling cannot be based on constant coefficients time domain simulations. These can infact lead to incorrect estimates of rolling amplitudes even when the parameters have been obtained through high level parameter estimation procedures based on experimental data. The analysis indicates also a marked dependence of the effective wave slope coefficient on wave amplitude. The introduction of both these dependences on the rolling equation allows to reproduce the experimental results with great accuracy even at large amplitudes. 相似文献