共查询到19条相似文献，搜索用时 156 毫秒
1.
硬悬挂钻井隔水管涡激振动特性研究 总被引：1，自引：0，他引：1
针对深水钻井过程中遭遇强台风,基于安全性考虑要求钻井平台悬挂隔水管提前撤离的问题,采用软件SHEAR7针对HYSY981钻井平台硬悬挂隔水管系统避台风撤离作业过程中,受南海一年一遇海流作用时诱发涡激振动(VIV)的情况,研究航速与悬挂长度对VIV特性的影响。研究表明,浮力块覆盖率越高,隔水管系统张力越小;浮力块分布对隔水管系统VIV响应影响较大,25%交错布置方案VIV响应最弱。隔水管并非越短越好,要综合考虑洋流剖面、隔水管配置和平台航行的影响;在不同悬挂长度及航行条件下的VIV响应,在撤离作业前应尽量避免在高流速区布置浮力单根,撤离作业时应尽量采用顺流而避免平台逆流航向。 相似文献
2.
动力定位钻井平台已逐步被广泛应用于深水和超深水油气资源的勘探开发。由于面临复杂的海洋环境和作业环境,钻井平台可能会出现动力定位失效移位的紧急情况。文章在分析井口作业指南发展历史的基础上,基于国际上对井口作业指南的要求,研究钻井平台动力定位失效移位模式并对其进行分析,建立钻井平台井口作业指南红色界限值的计算方法,并自主开发相应计算软件;该软件可对钻井平台红色界限值、黄色界限值和警告界限值进行全面计算,完善井口作业指南,保证深水动力定位钻井平台的作业安全。 相似文献
3.
针对在南海海域频发的台风自然灾害,考虑海况随机性、结构随机性以及作业参数的随机性,采用梯度投影确定取样点的响应面法,分别建立P2D、D2P和P2P(P指生产立管,D指钻井立管)三种作业模式下TLP串行立管系统的结构极限状态方程。并在建立立管可靠性分析模型的基础上,确定一种立管可靠度计算方法。算例结合南海某TLP平台给出了上述方法的具体应用。研究表明,10年一遇台风情况下,P2D、D2P和P2P三种工况中生产立管系统的失效概率均小于0.001%,钻井立管系统的可靠度分别为0.016%和0.113%。在大于200年一遇的强台风情况下,P2P工况时的上下游生产立管系统失效概率均大于0.32%和0.018%。因此建议10年一遇台风情况下,停止钻井立管作业;在大于200年一遇的强台风情况下,停止生产立管作业。研究结果可为南海TLP立管系统可靠度评估及安全作业技术支持。 相似文献
4.
5.
研究深海顶张力立管(TTR)的固有振动特性.通过考虑两种不同的分析模型,研究沿水深变化的轴力以及张紧环运动对于立管固有振动频率和振型的影响.考虑立管顶端动边界条件及立管轴力随水深变化,提出了计算深水顶张力立管固有振动频率的方法,给出考虑浮体升沉及张紧环运动时顶张力立管的固有振动特性.结果表明,考虑变轴力和张紧环的影响是计算立管固有频率需要考虑的;立管浮体的运动,导致立管频率显著变化,从而改变立管的共振特性. 相似文献
6.
张力腿平台(TLP)水下丛式井口布局设计关系到立管服役期间的安全性,是含有丛式井口平台设计过程中考虑的主要因素。根据TLP立管安装、钻井以及防碰等要求,考虑尾流效应对丛式立管的影响,研究水下丛式井口布局设计准则,对丛式井口—立管系统进行碰撞分析以确定水下井口间距阈值,提出水下丛式井口圆形布局方法和相应的布局设计流程。通过算例对计算方法进行了具体运用。研究表明:与目前采用的"等边三角形网格"方法相比,水下丛式井口圆形布局方法可允许水下整体基盘安装位置误差达到水下井口间距阈值的20%,立管的最大倾角可达到0.5°,安装作业窗口增加1倍以上。本方法对水下整体基盘安装位置误差的容错能力强,能有效扩大丛式立管钻井和安装作业窗口,提高丛式立管作业安全性,研究结果可为TLP丛式井口的设计提供参考。 相似文献
7.
深海浮式平台与其系泊系统的耦合作用显著,在数值分析中,需要合理确定二者耦合边界的模拟方法。本文以深水半潜式钻井平台及其系泊系统为研究对象,将浮体与系泊之间复杂的连接边界简化为固接、铰接和弹簧连接三种边界约束模型,提出了弹簧连接中相关参数的确定方法,并将不同边界约束下系缆张力的计算结果与模型试验数据进行对比验证。通过算例分析,探讨不同边界约束对平台运动、系缆张力及其疲劳损伤的影响,给出设计分析的选择建议。 相似文献
8.
研究了涡激力作用导致顶张力立管基于双频激励的参量共振机理。随着海洋油气开发走向深水,参量共振成为深海立管设计面临的挑战之一。立管系统一旦发生参量共振,将因应力过大或疲劳损伤而发生破坏,造成油气泄漏从而带来环境污染和重大经济损失。顶张力立管受涡激力作用产生横向运动,引起轴向张力波动,满足一定条件时,立管将发生参量共振。目前研究多以单频外激励探讨立管的马修不稳定性,而实际激励为多频叠加,因此双频外激励被提出并被应用于对立管参量稳定性的探讨。研究建立了顶张力立管非线性耦合的运动方程,并推导了多频激励马修方程,采用布勃诺夫-伽辽金法求解有阻尼马修方程,对比分析了单频和双频激励对顶张力立管参量稳定性的影响,探讨了双频激励马修方程设计深海顶张力立管参量稳定性的应用。研究表明:涡激致顶张力立管产生轴向应力波动,进而导致立管系统发生参量共振的现象值得设计人员关注;此外,实际工程设计中激励函数的选取,对被研究系统参量稳定性特性以及阻尼特性的预测具有决定性影响。 相似文献
9.
为保证深水钻井作业过程中锚泊系统的安全性,降低事故发生率,提高事故应急处置能力,基于故障树、工作安全分析等风险分析方法,并结合锚泊系统自身特性,设计深水半潜式平台锚泊系统风险分析流程。依据钻井作业周期顺序,从抛锚、钻井作业及起锚阶段设计锚泊系统作业风险分析流程。搜集统计锚泊系统常见事故类型,设计走锚风险分析流程,建立走锚事故应急程序。结果表明:所设计的锚泊系统风险分析流程能够弥补现有锚泊系统风险分析的不足,为开展锚泊系统全生命周期内的风险分析提供理论指导,为其它锚泊系统风险相关研究提供参考。 相似文献
10.
水下井口的疲劳完整性是海洋油气田长期安全开采的前提。工业界往往采用贴应变片直接测量水下井口应变来计算弯矩和疲劳损伤，但水下井口应变片粘贴困难且不能长时间连续工作。采用对水下井口监测方法，基于隔水管—防喷器组—水下井口的运动和力学特性，考虑防喷器组惯性力矩建立系统耦合动力学方程，最终形成基于监测数据的水下井口循环弯矩计算方法。以南海某深水水下井口为例，建立隔水管—防喷器组—水下井口系统有限元模型并进行动态分析，提取隔水管底部张力、转角、防喷器组加速度及转角等参数，代入所建立的系统耦合动力学模型，得到水下井口弯矩与有限元计算结果吻合良好。研究表明只需通过在线监测获得所需的输入数据，无需监测水下井口应变即可获取水下井口循环弯矩。建立的系统耦合动力学模型可为水下井口疲劳完整性评估提供理论依据。 相似文献
11.
12.
This work proposes nonlinear parallel spring-damper scalar elements in series with a rigid beam element to represent drilling riser tensioner behavior during an emergency disconnection scenario in global riser analysis. The software package used was Orcaflex. This is a simpler approach than the more complex, full hydraulic-pneumatic-mechanic dynamic simulation modelling of the tensioning system, commonly used in literature, which can be time consuming and numerically more sensitive. The model can also be used to represent top tension variation in global riser analysis, allowing for more complex and precise simulations, especially for fatigue life and overpull estimations. The results show adequate agreement with the researched bibliography. 相似文献
13.
A static three-dimensional analytical method for drilling risers experiencing large displacements and slip at the top joint is presented. The riser is described in cylindrical coordinates as a three-dimensional tensioned string, without bending or torsional stiffness. The vertical vessel displacement is not taken into account. The equilibrium configuration is obtained from the stationary condition of the total potential energy functional. Kinematic boundary conditions are introduced for the radial displacement only. The riser orientation at the top directly follows from the natural boundary conditions based on the variational treatment of the energy functional. 相似文献
14.
The flexible riser top connection is a critical region for lifetime assessment due to large tension/curvature variations and modeling uncertainties. The bend stiffener polyurethane mechanical response not only presents a nonlinear loading rate and temperature dependency but is also subjected to weather ageing during operation, which may affect its mechanical behavior over time. The top tension, employed for riser local cross-section stress calculation, is usually obtained from global dynamic analyses performed under selected environmental conditions, if direct measurement is not available. As a consequence, both the bend stiffener effect on the curvature distribution and the top tension time series present inherent uncertainties for riser lifetime (re)assessment. In the present work, a proposed monitoring approach composed by gyrometers installed along flexible riser/bend stiffener top connection system length combined with an inverse problem methodology is numerically investigated to estimate the following parameters: (i) polyurethane hyperelastic response and (ii) effective top tension. The top connection system is modeled using a large deflection beam bending model and the parameters are estimated using a damped least-square minimization approach with the Levenberg–Marquardt algorithm. For the preliminary feasibility investigation, the gyrometer experimental data is numerically estimated through Monte Carlo simulations. A case study is carried out to investigate the influence that the number of sensors, sensors arrangement, loading conditions and top connection model have on the inverse parameters estimation. The results indicate that the proposed monitoring approach and inverse parameter estimation methodology may effectively reduce flexible riser lifetime calculation uncertainties. 相似文献
15.
复杂海洋环境中，顶张力立管顶部平台受到不同分量叠加的波浪作用，导致其轴向张力与多个频率相关，系统产生多频参激与涡激的联合振动，其动力学行为变得更为复杂，尤其是分岔和混沌等非线性振动特性有待进一步分析。首先，基于欧拉—伯努利梁理论，引入范德波尔尾流振子，建立和推导受多频参激—涡激联合作用下立管的动力学模型及其运动微分方程；接着，利用伽辽金法得到离散后的常微分方程组，采用多尺度法得到系统共振响应的调谐方程；最后，通过数值算例探究系统在多源和多频载荷联合作用下的共振响应。结果表明：对于多频参数激励，其中一个参数激励幅值在立管振动中起主导作用，而另一个会引起分岔的位置、数量和性质发生改变；随质量—阻尼参数增大，系统共振响应幅值整体先增大后减小，各分岔点出现的位置整体先向泄涡频率较大处移动，随后向泄涡频率较小处移动；质量—阻尼参数的变化还可能诱使系统发生倍周期分岔和混沌现象，危害结构安全。此外，采用直接数值积分求解微分方程组，验证近似分析结果，两者吻合较好。 相似文献
16.
As drilling operations move into remote locations and extreme water depths, recoil analysis requires more careful considerations and the incidence of emergency disconnect is increased inevitably. To accurately capture the recoil dynamics of a deep-water riser in an emergency disconnect scenario, researchers typically focus on modelling the influential subsystems (e.g., the tensioner, the mud discharge and seawater refilling process) which can be solved in the preprocessing, and then the determined parameters are transmitted into an existing global riser analysis software. Distinctively, the current study devotes efforts into the coupling effects resulting from that the suspended riser reacts the platform heave motion via the tensioner system in the course of recoil and the discharging fluid column follows the oscillation of the riser in the mud discharge process. Four simulation models are established based on lumped mass method employing different formulas for the top boundary condition of the riser and the discharging flow acceleration. It demonstrates that the coupling effects discussed above can significantly affect the recoil behavior during the transition phase from initial disconnect to the final hang-off state. It is recommended to develop a fully- coupled integrated model for recoil analysis and anti-recoil control system design before extreme deep-water applications. 相似文献
17.
This paper deals with a numerical study of the transient effect of tendon disconnection on global performance of an extended tension leg platform (ETLP) during harsh environmental conditions of Gulf of Mexico (GoM). The ETLP has twelve tendons with twelve production top-tensioned risers (TTRs) and one drilling riser. The risers are attached by hydro-pneumatic tensioners. A time-domain nonlinear global-motion-analysis program for floating hulls coupled with risers/mooring lines is developed to model the transient effects associated with tendon disconnection at the top or the bottom. The sudden disconnection of one or more tendons causes the change of stiffness and natural periods, the imbalance of forces and moments of the total system, and possibly large transient overshoots in tension at the moment of disconnection. The breakage at the top and the unlatch at the bottom also make different impacts on the system. The transient responses and tensions are compared and discussed in the viewpoint of the robustness of the system. The survivability of a TLP with the loss of one or two tendons by accident during a lesser-than-extreme environment can also be checked by this kind of time-domain simulation technique. 相似文献
18.
南海海域台风频发,对于深水浮式钻井平台,常规避台模式要求回收所有隔水管,但是在深水、超深水海域,这种应对台风的方案有其局限性。据测算,水深超过1 500 m时,台风准备时间(回收所有隔水管、处理井口的作业时间)超过4天,而目前天气预报的水平只能提前4～5天,因此常规避台难度极大,经常会遭遇到还没有起完隔水管,台风已经逼近平台位置的情况,悬挂隔水管成为一种不得不面对的防台避台方案。硬悬挂和软悬挂是目前悬挂隔水管两种常见的模式,由于软悬挂能够补偿和缓解钻井船升沉施加在悬挂隔水管上的动态载荷,因此业内普遍认为软悬挂模式在提高悬挂隔水管对海洋环境的适应能力方面具有一定的优势,但是常规的软悬挂模式作业程序复杂,而且实施过程中存在伸缩节、张力器液缸等相关设备冲程超标的风险。通过对隔水管悬挂状态下横向和轴向的动力响应进行分析,确定了限制隔水管悬挂安全的主要因素,针对隔水管应力超标和转角过大、干涉等风险,设计了一种具有加装扶正器的锥形悬挂短节;针对悬挂隔水管的轴向压缩风险,研制了一种具有补偿功能的隔水管悬挂装置,降低了悬挂隔水管动态载荷产生轴向压缩和动态应力超标的风险。定量评估表明使用新型隔水管悬挂系统,可以将常规的悬挂窗口由不足10年一遇波流环境条件提高到满足100年一遇的波流环境条件,大大提高了悬挂隔水管的安全性。 相似文献
19.
Dynamic Characteristics of Marine Risers Conveying Fluid 总被引：10，自引：0，他引：10
The lateral vibration differential equation for a marine riser conveying fluid is derived by useof the small deflection theory.and the effect of internal flow velocity and top tension on the natural fre-quency of the riser is studied by use of FEM.At the same time,the preliminary relationship between thenatural frequency and riser span under different internal flow velocities is obtained,the effect of riser sup-ports on the vibration frequency is computed.It is found that the natural frequency of the marine riser in-creases with the increase of top tension.however decreases with the increase of internal flow velocity.In ad-dition,the frequency decreases drastically with the increase of riser span. 相似文献