共查询到20条相似文献，搜索用时 31 毫秒
1.
A Novel Mechanical Gas-Tight Sampler for Hydrothermal Fluids 总被引：1，自引：0，他引：1
Ying Chen Shijun Wu Yingjun Xie Canjun Yang Jiafan Zhang 《Oceanic Engineering, IEEE Journal of》2007,32(3):603-608
A new mechanical gas-tight sampler has been designed to collect hydrothermal fluids at the seafloor. A key feature of the sampler is the novel sample valve which is pressure balanced under deep sea, and actuated by the ram on a submersible's manipulator. The sampler is designed to be deployed at the seafloor 3000 m underwater and can be used to sample hydrothermal fluid with temperature up to 400degC. Compressed gas is used to compensate for pressure reduction of sample fluids. Simulation of the flow system was conducted to estimate the fill rate. The sampler has been tested successfully in the first Sino-American Cooperative Deep Submergence Project from August 13 to September 3, 2005. 相似文献
2.
The paper presents the design and preliminary test results of a corer used for hard seafloor sediments sampling.Generally the sediment cores are provided by either gravity-type coring or deep-ocean drilling for a range of studies.However,in consideration of the operability and available sample length in collecting hard sediments,these methods exhibit no advantages.In this paper,a new corer which can exploit both hydrostatic energy and gravity energy for hard sediments coring is presented.The hydrostatic energy is provided by pressure differential between ambient seawater pressure and air pressure in an empty cavity.During sampling process,the corer penetrates into the sediment like a gravity corer and then automatically shifts to the percussion mode.The experiments in the laboratory indicate that the corer can complete 40 cycles in the sea with a cycle time of 2.8 seconds in percussion mode and impact the sample tube with the velocity of 0.2 m/s during each cycle.Besides,its adjustable falling velocity can make the corer achieve the maximum efficiency in coring different sediments. 相似文献
3.
An energy conversion system based on deep-sea pressure 总被引：1，自引：0，他引：1
A novel seawater pressure energy conversion system that utilizes seawater pressure to generate electricity has been studied in this paper. The energy conversion system utilizes the pressure difference between the pressurized seawater and the empty pressure container to drive hydraulic motor and the coaxially coupled generator to generate electric power. The output electric energy is recorded by the data logger throughout the process. In the current study, technical analysis is performed with the emphasis on conversion efficiency between seawater pressure energy and output electric energy. The analysis is conducted at various pressure differences through the throttle valve so as to obtain maximum conversion efficiency. Research shows that the optimum pressure difference through the throttle valve and the maximum conversion efficiency can be theoretically calculated when the properties of the conversion system are given. Simulation results have demonstrated the influence of pressure difference on conversion efficiency. The test apparatus has been designed, built and tested in 2004. It successfully generated electric energy of approximately 0.85 kW h at the depth of 2400 m with empty pressure container's holding capacity of 200 L in the voyage “DY105-16” in South China Sea on June 12, 2004. The actual conversion efficiency from seawater pressure energy to electric energy reaches as high as 63.8% which is attractive for underwater equipments. The success of the experiment has tested the feasibility of utilizing seawater pressure energy and brings a new power supply way for long-term in-situ underwater equipments. 相似文献
4.
《Deep Sea Research Part I: Oceanographic Research Papers》2002,49(1):189-196
A new gas-tight isobaric sampler for the collection of hydrothermal fluids venting at the seafloor has been designed, constructed, and tested at a ridge-crest vent site. The new device is constructed of chemically inert titanium, is gas-tight to 450 bar and can be used to sample fluids with temperatures up to 400°C. Compressed gas is used to maintain the sample at seafloor pressure before and during sample withdrawal onboard ship, allowing subsampling without degassing the fluid remaining in the sampler. This feature eliminates the need to collect separate gas-tight and major element samples since a single fluid sample can be analyzed quantitatively for major, trace, semi-volatile, and volatile components. The sampler fill rate is regulated to minimize entrainment of ambient seawater during collection of fluids from environments characterized by low fluid flow such as diffuse hydrothermal vents. In addition to deployment at the ridge-crest, the samplers can be used to collect gas-tight samples from other subseasurface environments such as hydrocarbon seeps, areas of methane-gas hydrate formation, cold seeps associated with serpentinites, regions of groundwater egress to the oceans, and the water column. 相似文献
5.
Jingqiang Wang Baohua Liu Guangming Kan Zhiwen Sun Xiangmei Meng 《Marine Georesources & Geotechnology》2018,36(5):515-521
The mechanical structure, the function modules, the working principles, and a sea trial of the newly developed ballast in situ sediment acoustic measurement system are reported in this study. The system relies on its own weight to insert transducers into seafloor sediments and can accurately measure the penetration depth using a specially designed mechanism. The system comprises of an underwater position monitoring and working status judgment module and has two operation modes: self-contained measurement and real-time visualization. The designed maximum working water depth of the system is 3,000?m, and the maximum measured depth of seafloor sediment is 0.8?m. The system has one transmitting transducer with the transmitting frequency band of 20–35?kHz and three receiving transducers. The in situ acoustic measurement system was tested at 15 stations in the northern South China Sea, and repeated measurements in seawater demonstrated good working performance. Comparison with predictions from empirical equations indicated that the measured speed of sound and attenuation fell within the predicted range and that the in situ measured data were reliable. 相似文献
6.
7.
原位测量技术在黄海沉积声学调查中的应用 总被引：8，自引：3，他引：8
介绍了最新研制的基于液压驱动贯入的自容式海底沉积声学原位测量系统及其在南黄海中部海底沉积声学调查中的应用。该系统可以实现对海底沉积物声速和声衰减系数进行原位测量,通过液压驱动装置将四根声学探杆匀速贯入到海底沉积物中,减少了对沉积物的扰动,可按照预设的工作参数在海底全自动工作,无需甲板上人员实时控制,采集的声波信号自容式存储于存储单元。系统工作水深为500 m,测量深度为1 m,测量频率为30 kHz,采样频率为10 MHz。使用该系统在南黄海中部获得了40个站位不同类型沉积物的声学特性原位测量数据,并使用CTD剖面仪对该系统声速测量进行了标定,相对误差均小于0.5%,表明该系统测量数据准确、可靠。 相似文献
8.
为准确建立海底地声模型,本文探讨地声模型的基本组成和基本结构。通过样品实验室测量,分析南海海底表层沉积物的密度、孔隙度与声速随着埋深变化的关系,得出海底实际存在的低声速表面–声速缓慢变化类型、低声速表面–声速增大类型、高声速表面–声速缓慢变化类型和高声速表面–声速增大类型4种典型地声结构;对比钻探测量,分析黄海海底沉积物的密度、孔隙度与声速随埋深变化关系,得出海底地声模型分层特征与地声结构组合特征。研究表明,地声模型可以归结为4种基本地声结构的组合,通过与底层海水声速、同层内声速剖面以及与上层海底沉积物下表面声速的比较,可以建立各种海底地声模型;基于实验室测量法建立的地声模型可以作为参考地声模型,但需要考虑实际海底温度和压力梯度以及海底沉积物的频散特性等,借助于声速比校正法和频散性理论模型进行计算及修正。 相似文献
9.
10.
Takeshi Naganuma Masanori Kyo Tatsuhiko Ueki Kazuhiko Takeda Jun-ichiro Ishibashi 《Journal of Oceanography》1998,54(3):241-246
A new hydrothermal fluid sampler has been developed to provide more maneuverability in underwater operation. The sampler characteristically
employs a shape-memory alloy, which senses high temperature and actuates the suction mechanism. A shape-memory alloy is also
used to switch the intake valve of the sampler, the intention being to avoid missampling when the inlet is in low temperature
water. Prototype samplers were designed to collect the fluids hotter than 80°C. Test sampling was performed at hydrothermal
vents (1372–1374 m deep) in the submarine volcano, Suiyo Seamount, Izu-Bonin Arc, northwestern Pacific. Observed fluid temperature
was between 138 and 298°C, while the ambient seawater temperature was 3.1°C. Each prototype collected about 100 ml fluid as
designed. The magnesium concentration in the samples indicated a seawater content of 47.5–90.8%, which indicates the entrainment
of ambient seawater. Microscopic observatinn revealed the occurrence of microorganisms in the sample fluids at a population
density of 105 to 106 cells ml−1, which is 2–3 orders of magnitude higher than those in seawater at that depth. The use of the newly developed fluid sampler
will greatly facilitate the collection of vent-associated microorganisms, which are of potential biological and biotechnological
interest. 相似文献
11.
There has been much recent activity on developing and testing high-frequency seafloor volume scattering models and on the related high-resolution characterization of seafloor volumes. This paper will address another plausible volume scattering mechanism that has not yet received much attention-distributions of broken shell fragments in sediment (commonly referred to as shell hash). The shell fragments are modeled as nonaggregating spherical scatterers, and the spatial distribution of the shell pieces is determined using the Percus-Yevick packing factor. Computer simulations of the multiple scattering and a single scattering model are used to study the power backscattered by shell hash sediments as a function of the volume of scatterers and the frequency of the incident wave (10-100 kHz). Parameter values for simulations are obtained by stereological analysis of x-ray computed tomography scans of sediment cores. 相似文献
12.
利用单波束测深仪和蚌式取样器进行了日照石臼港扩建码头西侧约50km~2海域1:2 000~1:10 000的水深地形测绘和底质分析工作。调查结果表明,日照港西部海域可分4个水深区,其地形和沉积特征如下:1)航道区,浅水航道区等深线平行于码头岸线,水深11m,经过疏浚已形成向南倾斜的四级阶梯地形,疏浚中心处水深24m。航道区底质以分选中等的砾砂为主;2)港池区,水深6 m,等深线与港池岸线平行,水深向南渐增,海底地形平坦,坡降比3‰。底质以分选较好的粉砂和砂质粉砂为主,近岸有少量分选较差的泥质砂质砾;3)涛雒-付疃河口区,水下三角洲地形明显,5m以浅等深线呈弧形向东南方向凸出,坡降比最大可达14.2‰,底质类型为分选极好的砂和粉砂质砂;4)浅海区,海底地形平坦,平均坡降比1.9‰,6~10m等深线呈NE-SW向平行向外海增大,近南扩码头端向东偏转,底质类型为分选好的砂质粉砂和粉砂,并呈平行于海岸线向深水区呈粗-细-粗的带状分布。底质类型分布与水深条件基本吻合,但深水区出现的底质粗化现象,分析认为可能与南扩码头的挑流作用有关,海底沉积物呈向南运移趋势。 相似文献
13.
基于海底表层沉积物声速特征的南海地声模型 总被引：1，自引：1，他引：0
在由垂直声速梯度建立的地声模型基础上,通过引入沉积物与海水声速比和沉积物压缩波与切变波声速比两个表征沉积物声学特征参数得到更全面和有实际指导意义的地声模型。在沉积物声波传播FCMCM模型基础上,基于热作用和重力作用下沉积物两相介质的应力应变分析,建立TFCMCM和DFCFCM模型,运用模型校正表层沉积物声速特征来计算和解释地声模型。根据海底表层沉积物存在低声速和高声速两种类型,结合沉积物沿纵深孔隙度不变和变化两种类型,得到南海海底沉积物的两类四种典型地声模型:低声速孔隙度不变型、低声速孔隙度减小型、高声速不变型和高声速孔隙度减小型。运用这四种典型地声模型的组合解释了卢博提出的南海三种典型声速结构。认知声速结构将为南海声学探测海底、划分海底区域提供模型支持。 相似文献
14.
为满足对远洋环境进行长时间、大范围监测的实际需求,设计提出一种波浪动力滑翔机,该设备是一种无需携带能源即可实现自主航行的新型海洋监测平台,其主体结构由水面母船、水下牵引机和柔性缆绳三大部分组成。平台通过即时获取海洋中的波浪能、太阳能、风能作为行走的动力源,克服了传统海洋监测设备在能源供应上存在的短板。为进一步提升水下牵引机对波浪能的利用率,采用Ansys软件中的Fluent模块对水下牵引机进行水动力仿真研究,分析了侧翼板形状、侧翼板工作最大摆动角度以及侧翼板安装分布间距对滑翔机总体行走效率的影响。结果表明:NACA翼型侧翼板具有更好的水动力性能;随着最大摆动角度的增加,水下牵引机的推进效率先增大后减小,最大摆角在20°左右时,推进效果最佳;随着侧翼板分布间距的增大,水下牵引机的推进效率逐渐减小,分布间距在80 mm左右时,推进效果最佳。 相似文献
15.
Lei Sun Xiangmei Meng Guanbao Li Guangming Kan Baohua Liu 《Marine Georesources & Geotechnology》2020,38(5):595-603
AbstractThe high-frequency acoustic properties of seafloor sediments are very significant in seafloor study and underwater acoustic study field. In order to measure the sound speed and the attenuation for the small-scale sediment cores more accurately, this study developed a water coupled acoustic laboratory measurement system based on Richardson-Briggs technique. This method used the correlation comparison of waveforms received in sediment core and in identical reference tubes filled with water to measure sound speed and attenuation. The sound speed and attenuation of a clayey silt sediment sample were measured using the water coupled acoustic laboratory measurement system. This frequency dependence of the sound speed and attenuation showed that the clayey silt sediment has a weak positive sound speed dispersion, while the attenuation increases with a strong positive gradient within the measurement frequency range. This study also noted that the measured sound speed ratio match well with the empirical equations from literature. The measured attenuation factor data can fall in the Hamilton’s empirical prediction range. 相似文献
16.
In recent years, interface waves such as the Scholte wave have become important tools in the study of the geoacoustic properties of near-bottom seafloor sediments. Traditionally, these waves have been generated by explosive or pneumatic sources deployed at or near the seafloor and monitored by ocean-bottom seismographs or geophone arrays. While these sources generate the requisite interface waves, they also produce higher frequency compressional waves in the water and sediment that tend to contaminate the surface wave and make inversion of the data difficult in the near field. In this paper, a new source consisting of a freely falling projectile instrumented with an accelerometer is described. When the projectile impacts the bottom, the exact time history of the vertical force applied to the sediment is known and therefore may be convolved with the transfer function of a sediment geoacoustic model to produce accurate synthetic seismograms. Moreover, the vertical force applied to the seafloor is very efficient in generating surface wave motion while producing very little compressional wave energy so that the near-field signals are much more easily analyzed. An example of the use of the new source is presented including inversion of the received signals to obtain shear-wave velocity and attenuation as a function of depth in the near bottom sediments at a shallow-water site 相似文献
17.
Reducing overall power consumption is core issue in low power, high sampling rate, large storage data loggers necessary for long-term underwater acoustics research and other applications. A low-power microprocessor MSP430 offers a solution for the development of long-term deployment remote systems. In this paper, we present a multi-MSP430, master-slave architecture to resolve the power limitation issue. The proposed design is scalable in nature. For every additional slave unit installed in the array, the data sampling and streaming rate can be increased proportionally. We demonstrate the advantages of this concept using a multi-channel underwater acoustic recorder with a 100 kHz sampling rate. The performance of the system is demonstrated by a field acoustic experiment in which the reflection coefficient of the seafloor is measured. The proposed architecture will be applicable to many underwater long-term deployment systems. With its flexibility in configuration and synchronization of multi-channel sampling, it also provides a simple architecture for the construction of hydrophone arrays. 相似文献
18.
近23年的调查研究，使我们认识到分布于洋中脊、弧后盆地、岛弧和热点等环境的海底热液活动发育在多种围岩类型之上，包括超基性岩石、基性岩石、中性岩石、酸性岩石和沉积物。海底热液活动经历了岩浆去气作用、流体-岩石/沉积物相互作用和流体-海水混合，获取了岩浆、岩石、海水和沉积物的物质，构成了热液循环，产生了高温、低氧、高或低pH值、富含Fe、Mn、Cu、Zn、Pb、Hg、As等元素以及气体组分（甲烷、氢等）的喷口流体，影响了海水、沉积、岩石和生物环境，形成了热液柱、硫化物、含金属沉积物和蚀变岩石等热液产物，组成了海底热液系统。未来，促进海底热液活动探测技术和热液产物测试方法的发展，对海底热液区的岩石、喷口流体、热液柱、硫化物、含金属沉积物以及热液循环、生物活动的持续观测与研究，无疑将为人类探知海底地质过程及生命活动、保护海底热液环境和合理开发利用海底资源提供有力的工作支撑。 相似文献
19.
海底观测网因其实时、长期、连续、高精度时钟同步及原位等优势而逐渐成为人类研究海洋的新型平台,建设规模和应用水深都在不断扩大。海底观测网系统建设中,深水设备的精准定点布放及湿插拔作业是施工的难点。针对国内海底观测网精准定位布放作业存在的困难和问题,结合国内现有施工条件,提出一种大深度海底设备精准定点布放安装方法,实现南海深海海底观测网试验系统深水设备精准定位布放与ROV湿插拔作业,对未来大规模海底观测网及其它深水工程中设备的精准定点布放和安装,具有参考和借鉴意义。 相似文献
20.
Guanbao Li Jingqiang Wang Xiangmei Meng Baohua Liu Guangming Kan Guozhong Han Qingfeng Hua Yanliang Pei Lei Sun 《海洋学报(英文版)》2021,40(4):65-73
Building empirical equations is an effective way to link the acoustic and physical properties of sediments. These equations play an important role in the prediction of sediments sound speeds required in underwater acoustics.Although many empirical equations coupling acoustic and physical properties have been developed over the past few decades, further confirmation of their applicability by obtaining large amounts of data, especially for equations based on in situ acoustic measurement techniques, is required. A sediment acoustic survey in the South Yellow Sea from 2009 to 2010 revealed statistical relationships between the in situ sound speed and sediment physical properties. To improve the comparability of these relationships with existing empirical equations, the present study calculated the ratio of the in situ sediment sound speed to the bottom seawater sound speed, and established the relationships between the sound speed ratio and the mean grain size, density and porosity of the sediment. The sound speed of seawater at in situ measurement stations was calculated using a perennially averaged seawater sound speed map by an interpolation method. Moreover, empirical relations between the index of impedance and the sound speed and the physical properties were established. The results confirmed that the existing empirical equations between the in situ sound speed ratio and the density and porosity have general suitability for application. This study also considered that a multiple-parameter equation coupling the sound speed ratio to both the porosity and the mean grain size may be more useful for predicting the sound speed than an equation coupling the sound speed ratio to the mean grain size. 相似文献