共查询到18条相似文献，搜索用时 296 毫秒
1.
介绍了畸形波生成的方法并对各种线性合成畸形波的效率进行了对比。选用改进的随机波加瞬态波的方法模拟强非线性波———"新年波"的波形。采用微元法对张力腿平台的立柱和浮筒进行离散,编制程序对张力腿平台在强非线性波作用下的耦合动力响应进行了数值模拟,重点比较分析了张力腿平台在随机波及畸形波中所受波浪力、平台动力响应、系泊系统张力特性及浪向角对平台运动的影响。研究表明:在"新年波"作用下,0°浪向时,平台在x和z方向所受波浪力较随机波增长了约1/4,纵荡、垂荡及纵摇响应值分别增加了33%,38%和12%,张力腿张力幅值增加约20%,位于平台四角的张力腿张力有所差异,相邻两根张力腿的张力差别不大,浪向角对平台运动响应、张力腿张力的影响畸形波大于随机波的作用。为今后考虑强非线性波浪影响时张力腿平台的设计提供了借鉴和参考。 相似文献
2.
张力腿平台(TLP)是一种垂直系泊的半顺应半刚度式平台,预报平台的运动响应及锚泊系统的张力是张力腿平台结构设计的重要基础。应用挪威船级社SESAM软件在频域和时域内研究了张力腿平台在随机波浪中的非线性运动响应及系泊系统特性,并在试验室中通过缩尺比为1∶40的模型进行了试验验证。在试验验证的基础上,将仅考虑浪与考虑浪、流联合作用下的张力腿的张力平均值、幅值及标准差作了对比。结果表明,在较低海况时,考虑浪和流时的张力腿与不考虑流的情况变化不大;在较大海况时,流的影响不可忽略,考虑流的张力腿变化幅度要略大于不考虑流的情况。 相似文献
3.
为揭示张力腿平台涡激运动响应规律,采用数值模拟与模型试验相结合的方法研究了全水深系泊张力腿平台涡激运动响应。根据张力腿平台主尺度参数,按照几何相似制作了水池试验模型,在满足运动相似和动力相似的条件下开展了均匀流、剖面流模型试验,并将模型试验结果与数值模拟结果进行了对比,验证了数值模拟与模型试验结果的一致性。分析结果表明在均匀流作用下张力腿平台涡激运动的锁定区间在5.5<Ur<8.5,来流角对涡激运动影响较大。剖面流作用下平台涡激运动规律与均匀流作用基本一致,但剖面流造流引起的能量分散,使平台在XY平面的运动轨迹变得不规律,系泊系统提供的回复力对涡激运动幅值有抑制作用,来流角和流速对张力腿或立管模态影响明显。论文得到结论对于张力腿平台的工程设计有一定借鉴意义。 相似文献
4.
5.
在平台振荡条件下TLP张力腿的涡激非线性响应 总被引：7，自引：0，他引：7
给出了预测张力腿涡激横向振动的时域分析,考虑了波浪、海流、张力腿平台的横漂与垂荡诸因素.张力腿平台的垂荡引起张力周期性变化,对张力腿的涡激横向振动起参数激励的作用,使其动力响应更为复杂.讨论了参数激励下涡激响应的共振条件;以尾流振子模型为基础,发展了分析张力腿在动张力作用下的涡激振动的工程方法,并分析了一座TLP实例,给出了在横漂周期内张力腿上质点的相对位移、弯矩、剪力幅值的时间历程.结果表明,平台垂荡使张力腿的涡激响应幅值升高、高频成分增加,因此它对张力腿的疲劳设计是重要的. 相似文献
6.
延展式张力腿平台是一种适用于深水油气开采的海洋平台结构。提出一种新型平台由四个立柱和一个环形浮箱连接而成,环形浮箱是由四个箱型梁焊接而成。根据给出的南海海域的海况条件和相应的规范计算结构的环境载荷,运用SESAM软件Deep C模块,考虑风、浪、流等环境荷载的作用和张力腿系统的非线性影响,进行了时域耦合分析,得到了平台的运动位移时程、张力腿系统张力时程和张力极值等。模拟波浪破碎作为冲击载荷,得到张力腿平台在冲击荷载作用下的运动位移时程、张力腿系统的张力时程。研究结果表明:该新型平台具有良好的运动响应,张力筋腱应力满足安全要求;在冲击载荷作用下新型平台的运动响应也满足要求。 相似文献
7.
8.
在一定来流条件下,张力腿平台(tension leg platform,简称TLP)的立柱后缘出现周期性的交替旋涡脱落,致使立柱受到垂直于来流方向的升力和平行于来流方向的阻力作用,导致TLP产生大幅度往复运动,显著增加平台结构和系泊系统的负载。目前,关于单柱、多柱结构绕流问题的研究较多,但对于TLP绕流特性的研究较少,机理尚存不明确的地方。为研究TLP的绕流力变化情况和流场特征,开展了数值模拟分析。利用计算流体动力学数值模拟软件,基于雷诺平均(RANS)法和分离涡模拟(DES)法对TLP绕流场进行仿真分析,揭示了TLP的绕流特性。结果表明,在3种来流角度和多个折合速度Vr下,TLP绕流的流体力系数存在明显差异,升力系数时域曲线呈现脉动性。TLP的上、下游立柱间存在明显的相互作用,影响了旋涡的形成与发展。TLP的旋涡脱落大多集中在平台固有频率附近,且在Vr=7,来流角度为0°时,升力系数频谱峰值最大,旋涡脱落集中。 相似文献
9.
张力腿平台内孤立波作用特性数值模拟 总被引：1，自引：1，他引：0
依据三类内孤立波理论KdV、eK dV和MCC的适用性条件,采用Navier-Stokes方程为流场控制方程,以内孤立波诱导上下层深度平均水平速度作为入口边界条件,建立了两层流体中内孤立波对张力腿平台强非线性作用的数值模拟方法。结果表明,数值模拟所得内孤立波波形及其振幅与相应理论和实验结果一致,并且在内孤立波作用下张力腿平台水平力、垂向力及力矩数值模拟结果与实验结果吻合。研究同时表明,张力腿平台内孤立波载荷由波浪压差力、粘性压差力和摩擦力构成,其中摩擦力很小,可以忽略;水平力的主要成分为波浪压差力和粘性压差力,粘性压差力与波浪压差力相比较小却不可忽略,流体粘性的影响较小;垂向力中粘性压差力很小,流体粘性影响可以忽略。 相似文献
10.
11.
Investigated is the coupled response of a tension leg platform (TLP) for random waves. Inferred are the mass matrix, coupling stiffness matrix, damping matrix in the vibration differential equation and external load of TLP in moving coordinating system. Infinitesimal method is applied to divide columns and pontoons into small parts. Time domain motion equation is solved by Runge-Kutta integration scheme. Jonswap spectrum is simulated in the random wave, current is simulated by linear interpolation, and NPD spectrum is applied as wind spectrum. The Monte Carlo method is used to simulate random waves and fluctuated wind. Coupling dynamic response, change of tendon tension and riser tension in different sea conditions are analyzed by power spectral density (PSD). The influence of approach angle on dynamic response of TLP and tendon tension is compared. 相似文献
12.
浮体运动是引起钢悬链式立管(steel catenary riser,简称SCR)动态响应和疲劳损伤的关键因素,目前研究SCR问题时,为简化计算往往仅考虑平台一阶运动,忽略二阶运动影响。而实际上不同浮体结构的二阶运动响应特征明显,拟以SCR服役张力腿平台(tension leg platform,简称TLP)为例,探讨浮体二阶运动对SCR触地区动态响应的影响。建立考虑海床刚度退化的管土作用模型以改进现有的CABLE3D RSI程序,通过编写程序接口,将有限元分析得到的平台实际运动响应导入,研究平台不同运动作用下SCR触地区的位移、动力响应及疲劳分布情况。根据波流作用方向将TLP二阶慢漂运动分为近端和远端漂移两种工况,发现二阶运动下立管与海床的作用范围会增大,且触地区不仅发生高频小幅振荡运动,同时伴随低频大幅运动响应;平台远端漂移时,管内张力敏感程度高,而近端漂移时触地区的弯矩显著增大,都会不同程度提高触地区的疲劳损伤率。研究可为服役不同浮体的SCR响应预测与疲劳分析提供参考和借鉴。 相似文献
13.
A.K. Jain 《Ocean Engineering》1997,24(7):577-592
Among the compliant platforms, the tension leg platform (TLP) is a vertically moored structure with excess buoyancy. The TLP is designed to behave in the same way as any other moored structure in horizontal plane, at the same time inheriting the stiffness of a fixed platform in the vertical plane. Dynamic response analysis of a TLP to deterministic first order wave forces is presented, considering coupling between the degrees-of-freedom surge, sway, heave, roll, pitch and yaw. The analysis considers nonlinearities produced due to changes in cable tension and due to nonlinear hydrodynamic drag forces. The wave forces on the elements of the pontoon structure are calculated using Airy's wave theory and Morison's equation ignoring diffraction effects. The nonlinear equation of motion is solved in the time domain by Newmark's beta integration scheme. The effects of different parameters that influence the response of the TLP are then investigated. 相似文献
14.
Coupled Dynamic Response Analysis of A Multi-Column Tension-Leg-Type Floating Wind Turbine 总被引：4，自引：3，他引：1
This paper presents a coupled dynamic response analysis of a multi-column tension-leg-type floating wind turbine (WindStar TLP system) under normal operation and parked conditions. Wind-only load cases, wave-only load cases and combined wind and wave load cases were analyzed separately for the WindStar TLP system to identify the dominant excitation loads. Comparisons between an NREL offshore 5-MW baseline wind turbine installed on land and the WindStar TLP system were performed. Statistics of selected response variables in specified design load cases (DLCs) were obtained and analyzed. It is found that the proposed WindStar TLP system has small dynamic responses to environmental loads and it thus has almost the same mean generator power output under operating conditions as the land-based system. The tension mooring system has a sufficient safety factor, and the minimum tendon tension is always positive in all selected DLCs. The ratio of ultimate load of the tower base fore-aft bending moment for the WindStar TLP system versus the land-based system can be as high as 1.9 in all of the DLCs considered. These results will help elucidate the dynamic characteristics of the proposed WindStar TLP system, identify the difference in load effect between it and land-based systems, and thus make relevant modifications to the initial design for the WindStar TLP system. 相似文献
15.
Analyzing the dynamic response and calculating the tendon tension of the mooring system are necessary for the structural design of a tension leg platform （TLP）. The six-degree-of-freedom dynamic coupling responses and the mooring characteristics of TLP under random waves are studied by using a self-developed program. Results are verified by the 1：40 scaling factor model test conducted in the State Key Laboratory of Ocean Engineering at Shanghai JiaoTong University. The mean, range, and standard deviation of the numerical simulation and model test are compared. The influences of different sea states and wave approach angles on the dynamic response and tendon tension of the mooring system are investigated. The acceleration in the center and corner of the deck is forecasted. 相似文献
16.
Abstract This article discusses a possible alternate foundation system for a tension leg platform (TLP) in deep water. It was developed through Tecnomare S.p.A. for Agip S.p.A. during a feasibility study of a site located in the southern Adriatic Sea having a water depth of 827 m. The system is a combination of a pile‐gravity foundation, with relatively short (?20 m) steel piles of very large diameter (6 to 12 m) called “superpiles,”; which are closed at the top and open at the bottom. The superpiles are installed in soft soil under the effect of self‐weight and active suction. Permanent tension of the TLP tendons is equilibrated by self‐weight only; tension due to wave action is equilibrated by the weight of the soil inside the superpiles. In fact, a pulsating tension applied to the superpiles generates a suction in the pore water that tends to keep the soil plug inside the cylinder and prevents the cylinder as a whole from being extracted from the (impervious) foundation soil. The results of analyses of the installation and in service behavior of superpiles are described on conventional principles of soil mechanics and related to a typical profile at the Adriatic site. Installation problems are briefly discussed; then the stability in service is examined to evaluate the capacity of superpiles in compression and tension and the associated factors of safety. Finally, considering the pore pressure gradient generated by the applied tension inside the soil plug, the flow rate and related deformations during storms and during the entire expected life of the TLP are evaluated. The proposed superpile system appears to be feasible, simple to install, and economical. Further study and experimental research are justified to optimize the system. 相似文献
17.
Among compliant platforms, the tension leg platform (TLP) is a hybrid structure. With respect to the horizontal degrees of freedom, it is compliant and behaves like to a floating structure, whereas with respect to the vertical degrees of freedom, it is stiff and resembles a fixed structure and is not allowed to float freely. The greatest potential for reducing costs of a TLP in the short term is to go through previously applied design approaches, to simplify the design and reduce the conservatism that so far has been incorporated in the TLP design to accommodate for the unproven nature of this type of platform. Dynamic analysis of a triangular model TLP to regular waves is presented, considering the coupling between surge, sway, heave, roll, pitch and yaw degrees of freedom. The analysis considers various nonlinearities produced due to change in the tether tension and nonlinear hydrodynamic drag force. The wave forces on the elements of the pontoon structure are calculated using Airy's wave theory and Morison's equation, ignoring the diffraction effects. The nonlinear equation of motion is solved in the time domain using Newmark's beta integration scheme. Numerical studies are conducted to compare the coupled response of a triangular TLP with that of a square TLP and the effects of different parameters that influence the response are then investigated. 相似文献
18.
钢悬链线立管(SCR)在安装过程中,通常会表现出复杂的动态特性,加强其安装技术及分析方法的研究具有重要意义。基于SCR-Spar生产系统,对深水SCR的安装方法进行研究,给出SCR典型安装步骤和各步骤中的关键问题。采用有限元软件OrcaFlex对海底提升和穿越拖拉安装进行了分析。基于整体时域分析,给出SCR安装操作方案和模拟分析方法,分析了控制安装操作的关键参数及其对SCR安装的影响。研究结果表明,SCR提升操作宜在空管状态下进行,初始提升速度和提升结束时吊头最终位置是控制管线应力/应变水平的主要因素。对于穿越拖拉操作,减小吊头与Spar的初始和最终间距,适当减小穿越拖拉缆长度对控制应力/应变水平是有利的,收/放缆速度对安装影响较小。 相似文献