共查询到18条相似文献，搜索用时 312 毫秒
1.
多消浪室局部开孔沉箱防波堤反射特性的迭代解析研究 总被引：1，自引：0，他引：1
基于势流理论，对多消浪室局部开孔沉箱防波堤的反射特性进行解析研究。研究中采用开孔墙处的二次压力损失边界条件，可以直接考虑波高对于开孔墙处能量损失的影响。利用匹配特征函数展开法和迭代方法得到当前问题的解析解。收敛性验证表明，迭代计算和级数解均具有良好的收敛性。该解析解的计算结果与分区边界元的数值计算结果一致，并且与已有的试验结果符合良好。通过算例分析，研究开孔沉箱防波堤反射系数的主要影响因素。结果表明：与单消浪室开孔沉箱防波堤相比，多消浪室开孔沉箱防波堤可以在更宽的波浪频率范围内保持低反射；增大开孔墙的开孔率，有利于降低多消浪室开孔沉箱防波堤的反射系数；当开孔墙的开孔率沿着入射波方向依次递减时，多消浪室开孔沉箱防波堤的反射系数较小。本文所建立的解析模型简单可靠，可用于工程初步设计中分析开孔沉箱防波堤的水动力性能。 相似文献
2.
本文基于雷诺平均的Navier-Stokes方程和k-ε模型求解湍流流动,采用流体体积法(Volume of Fluid,VOF)追踪自由表面运动,建立无反射波浪数值水槽,对多消浪室开孔沉箱的消浪特性进行数值模拟研究。将单消浪室和多消浪室开孔沉箱反射系数和结构前波面分布的数值分析结果与物理模型试验结果进行对比验证,两者符合良好。利用数值算例,研究多消浪室开孔沉箱的反射特性以及开孔结构附近的速度场和湍流强度分布。分析结果表明:波浪与开孔沉箱相互作用时,涡旋和湍动主要分布在开孔墙和消浪室内部自由表面附近;与单消浪室开孔沉箱相比,多消浪室开孔沉箱可以更有效的耗散波浪能量,降低结构的反射系数。本文分析结果可为开孔沉箱结构的工程设计提供参考依据。 相似文献
3.
双消浪室局部开孔沉箱防波堤具有低反射、结构受力小、适宜较大水深和工程造价低等优点。为明确双消浪室局部开孔沉箱水动力特性的主要影响因素,采用理论分析和物理模型试验相结合的方法,对规则波和不规则波作用下双消浪室局部开孔沉箱防波堤的反射特性进行研究。基于势流理论,建立规则波和不规则波对局部开孔沉箱防波堤作用的三维解析解,采用二次压力损失边界条件考虑沉箱开孔墙对波浪运动的影响,利用周期性边界条件考虑防波堤结构沿长度方向的周期性变化。开展相应规则波和不规则波物理模型试验,验证理论模型的合理性。通过算例分析,研究不同波浪要素和结构参数对防波堤反射特性的影响。研究表明:双消浪室局部开孔沉箱相对消浪室宽度取值为0.08~0.20,沉箱前墙开孔率大于后墙开孔率时,防波堤在较大波浪频率范围内消波效果显著;当前后墙的开孔率相等时,防波堤反射系数的最小值随着开孔率增大而减小。 相似文献
4.
基于线性势流假定,对斜向波作用下带横隔板局部开孔沉箱防波堤的水平波浪力进行了理论研究。给出了开孔沉箱法向水平力和横隔板受力的理论计算方法,在极限情况下波浪力的计算结果与文献中的已有结果一致。利用数值算例分析了开孔沉箱总水平力的主要影响因素。开孔沉箱法向总水平力的减小主要集中于结构上半部分波浪影响范围以内。增加单个开孔沉箱的长度有利于减小结构所受总水平波浪力。当波浪入射角或沉箱前开孔墙孔隙影响系数幅值较大时,开孔沉箱横隔板上总水平力的最大值要超过相应的沉箱法向总水平力,此时要注意横隔板的强度问题。 相似文献
5.
由于开孔前墙和消浪室具有强扰动作用,所以开孔沉箱结构具有很好的消浪效果。本文通过日照港岚山港区码头开孔沉箱结构的物理模型试验,研究了沉箱不同开孔位置的消浪效果和水动力特征,分析了不同方案的反射系数和越浪量。结果表明：水位对反射系数的影响较大,开孔位置较高的方案,其消浪性能较好,且越浪量较小。选择反射系数和越浪量均较小的设计方案进行了水动力试验,结果表明：水平力最大时对应的浮托力约为最大浮托力的60%;浮托力最大时对应的水平力约为最大水平力的75%;波浪对开孔沉箱的作用主要集中于外壁迎浪侧,内部结构受到的波浪力很小;第二消浪室波浪力小于第一消浪室。 相似文献
6.
基于势流理论,对半圆型开孔潜堤在波浪作用下的水动力特性进行解析研究。利用多极子展开法和分离变量法,在极坐标系下建立半圆型开孔潜堤内外流场的速度势表达式,通过迭代匹配求解开孔板处的非线性压力损失边界条件,确定速度势表示式中的展开系数,计算反射系数、透射系数、波浪力等水动力参数。将水动力参数的解析计算结果与分区边界元法的数值计算结果进行对比,符合良好。通过算例分析,明确了潜堤半径、开孔率等对反射系数,透射系数和波浪力的影响规律。研究结果可为半圆型防波堤的工程设计提供有效指导。 相似文献
7.
开孔率是开孔沉箱波浪反射系数的重要影响因素,迄今为止关于开孔沉箱的物模试验研究成果(包括《防波堤设计与施工规范》)中,开孔率μ通常以线性关系反映在开孔沉箱波浪反射系数的计算关系式中,适用范围为0.2~0.4。但当μ0.2或μ0.4时,开孔率μ对波浪反射系数Kr的影响规律尚需进一步的研究探讨。现借助二维数值波浪水槽,在扩大了的开孔率取值范围内,模拟不规则波与可渗明基床上开孔沉箱的相互作用。结果表明:在0.2≤μ≤0.4的范围内,用线性关系描述开孔率μ对波浪反射系数Kr的影响是合适的;在μ0.4时,数模值和物模试验拟合的经验关系式的趋势是一致的;在μ0.2时,开孔沉箱反射系数K_r随开孔率μ的减小而增大,用物模试验拟合的经验关系式及《防波堤设计与施工规范》中计算公式的线性关系来描述开孔率μ对反射系数K_r的影响是不恰当的。研究成果对开孔沉箱消浪机理的深入认识和开孔沉箱结构的优化设计具有重要意义。 相似文献
8.
开孔沉箱是将传统沉箱的前壁开孔,使沉箱前的入射波浪与反射波浪非同相位叠加,达到消能目的。消浪室是开孔沉箱的重要特征结构,其宽度对开孔沉箱的消浪性能具有重要影响。针对可渗明基床开孔沉箱,赋予消浪室宽度以较大的变化范围,开展专项物模试验,研究探讨了在规则波与不规则波作用下,相对消浪室宽度对可渗明基床开孔沉箱前波高反射系数的影响规律,发现反射系数随相对消浪室宽度的增加呈减小—增大—减小的振荡特性,这一发现有别于前人的研究成果,对工程中开孔沉箱消浪室结构的优化设计具有借鉴意义。同时,对试验工况进行数值模拟和解析计算,以物模试验值为标准,评价两种方法在研究相对消浪室宽度对开孔沉箱波高反射系数影响时的规律把握能力及计算精度,对工程中应用这两种方法给出相关建议。 相似文献
9.
10.
11.
The interaction of diagonal waves with perforated-wall breakwater partially filled with rock fill is studied using the linear potential theory. By means of the matched eigenfunction expansion method, an analytical method is presented to calculate the reflection coefficient and the wave force coefficient of the breakwater. The calculated results of the reflection coefficient for limiting cases are the same to the existing results. The main effect factors of the reflection coefficient and the wave force coefficient are analyzed by numerical examples. With the increasing of thickness of rock fill, the wave force coefficient on the perforated wall generally decreases, while the reflection coefficient increases. With the increasing of the incident angle of the wave, the reflection coefficient of the breakwater first decreases, reaches its minimum, and then increases monotonously. 相似文献
12.
This study examines the hydrodynamic performance of a wave absorbing double curtain-wall breakwater. The breakwater consists of a seaward perforated wall and a shoreward impermeable wall. Both walls extend from above the seawater to some distance above the seabed. Then the below gap allows the seawater exchange, the sediment transport and the fish passage. By means of the eigenfunction expansion method and a least square approach, a linear analytical solution is developed for the interaction of water waves with the breakwater. Then the reflection coefficient, the transmission coefficient and the wave forces acting on the walls are calculated. The numerical results obtained for limiting cases agree very well with previous predictions for a single partially immersed impermeable wall, the double partially immersed impermeable walls and the bottom-standing Jarlan-type breakwater. The predicted reflection coefficients for the present breakwater also agree reasonable with previous experimental results. Numerical results show that with appropriate structure parameters, the reflection and transmission coefficients of the breakwater may be both below 0.5 at a wide range of the relative water depth. At the same time, the magnitude of wave force acting on each wall is small. This is significant for practical engineering. 相似文献
13.
In this study, a mathematical model has been developed that can compute various hydrodynamic characteristics of a multiple-row curtainwall-pile breakwater. To examine the validity of the developed model, laboratory experiments have been conducted for double- and triple-row breakwaters with various combinations of drafts of curtain walls, porosities between piles, and distances between rows. Comparisons between measurement and prediction show that the mathematical model adequately reproduces most of the important features of the experimental results. As a whole, the transmission coefficient decreases with an increase in relative water depth, whereas the reflection coefficient, normalized run-up and force exhibit an opposite trend in their variations. With fixed values of the draft of the curtain wall and the porosity of lower perforated part of the first row of a double-row breakwater, as these values of the second row increase and decrease, respectively, the transmission coefficient decreases, as expected. On the other hand, their effects on wave reflection, run-up, and wave force change with the relative depth. As for the distance between the rows, the transmission coefficient becomes a maximum when it is about one half of the wave length, suggesting that this condition should be avoided to achieve the advantage of the breakwater in reducing wave transmission. It is shown that for prototype breakwaters, on an average, the transmission coefficient would be smaller than 0.3 for wave periods less than 6.0 s, and it would be about 0.45 even for the wave period of 9.0 s, although there would be a variation depending on the geometry of the breakwater. It is also shown that wave transmission is significantly reduced by multiple-row breakwaters compared with a single-row breakwater, while the difference between double-row and triple-row breakwaters is marginal. Finally, engineering monograms are provided for double-row breakwaters to be used in practical engineering applications of the breakwaters. 相似文献
14.
Wave interaction with a perforated wall breakwater with a submerged horizontal porous plate 总被引：1，自引：0，他引：1
This study examines the hydrodynamic performance of a new perforated-wall breakwater. The breakwater consists of a perforated front wall, a solid back wall and a submerged horizontal porous plate installed between them. The horizontal porous plate enhances the stability and wave-absorbing capacity of the structure. An analytical solution based on linear potential theory is developed for the interaction of water waves with the new proposed breakwater. According to the division of the structure, the whole fluid domain is divided into three sub-domains, and the velocity potential in each domain is obtained using the matched eigenfunction method. Then the reflection coefficient and the wave forces and moments on the perforated front wall and the submerged horizontal porous plate are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a perforated-wall breakwater with a submerged horizontal solid plate [Yip, T.L., Chwang, A.T., 2000. Perforated wall breakwater with internal horiontal plate. Journal of Engineering Mechanics ASCE 126 (5), 533–538] and a vertical wall with a submerged horizontal porous plate [Wu, J.H., Wan, Z.P., Fang, Y., 1998. Wave reflection by a vertical wall with a horizontal submerged porous plate. Ocean Engineering 25 (9), 767–779]. Numerical results show that with suitable geometric porosity of the front wall and horizontal plate, the reflection coefficient will be always rather small if the relative wave absorbing chamber width (distance between the front and back walls versus incident wavelength) exceeds a certain small value. In addition, the wave force and moment on the horizontal plate decrease significantly with the increase of the plate porosity. 相似文献
15.
Wang Jianyi Senior Engineer River Harbour Department Nanjing Hydraulic Research Institute Nanjing 《中国海洋工程》1992,(1)
This paper describes the design of a perforated caisson breakwater and presents the results of model test. Tests with regular and irregular waves have demonstrated that the perforated caisson breakwater has the advantages of low reflection coefficient, good wave-absorbing performance, relatively small wave height in front of the breakwater, and small amount of overtopping. Analyses have been made of the coefficient of reflection, wave height in front of the breakwater, and wave overtopping. Relevant figures and tables are presented for reference. 相似文献
16.
17.
波浪作用下方箱-水平板浮式防波堤时域水动力分析 总被引：1，自引：0，他引：1
在线性化势流理论范围内求解方箱-水平板浮式防波堤的波浪绕射和辐射问题,从时域角度分析了浮式防波堤的水动力特性.采用格林函数法将速度势定解问题的控制微分方程变换成边界上的积分方程进行数值求解,浮式防波堤的运动方程采用四阶Runge-Kutta方法求解.对不同层数水平板的浮式防波堤的波浪透射系数、运动响应和锚链受力进行了计算分析,结果表明方箱相对宽度对方箱-水平板浮式防波堤的波浪透射作用有重要的影响,透射系数随着方箱相对宽度的增加而减小.对于方箱加二层水平板的浮式防波堤,在本研究的计算条件下,当方箱相对宽度从0.110增加至0.295时,透射系数从0.88减小至0.30.水平板有利于增加浮式防波堤对波浪的衰减作用,但随着水平板层数从0增加至2,这种波浪衰减作用增加的程度趋弱.方箱-水平板的浮式防波堤的运动量小于单一方箱防波堤的运动量.与此对应,方箱-水平板防波堤的锚链受力小于单一方箱防波堤的锚链受力. 相似文献
18.
LIU Yong LI Yucheng TENG Bin MA Baolian 《海洋学报(英文版)》2007,26(3):129-141
The reflection of regular and irregular waves from a partially perforated caisson breakwater with a rock-filled core is examined. The present mathematical model is developed by means of the matched eigenfunction method. Numerical results of the present model are compared with the experimental data of different researchers. Numerical examples are given to examine the effect of rock fill on the reflection coefficient. The differences between regular and irregular waves are also investigated by means of theoretical and experimental results. It is found that the minimum reflection coefficient of irregular waves is larger than that of corresponding regular waves, but the contrary is the case for the maximum reflection coefficient. 相似文献