共查询到19条相似文献，搜索用时 359 毫秒
1.
2.
基于有限深两层流体KdV(Korteweg-de Vries)、eKdV(extended KdV)和MCC(Miyata-Choi-Camassa)理论,以内孤立波诱导上下层深度平均水平速度为入口边界条件,采用理想流体完全非线性欧拉方程,建立了两层流体中内孤立波生成的CFD(Computational Fluid Dynamics)数值模拟方法。以系列数值模拟结果为依据,结合内孤立波非线性和色散参数的组合条件,给出了选择合适内孤立波理论解作为CFD数值模拟入口边界条件的方法,从而实现了振幅与波形可控的内孤立波完全非线性数值模拟。 相似文献
3.
基于MCC理论的内孤立波数值模拟 总被引：3，自引：0，他引：3
基于MCC(Miyata-Choi-Camassa)理论,将内孤立波诱导上下层深度平均水平速度为入口条件,结合理想流体完全非线性欧拉方程,建立了两层流体中内孤立波生成与传播的CFD(Computational Fluid Dynamics)数值水槽方法。在系列数值模拟基础上,获得了内孤立波设计振幅与数值模拟振幅之间的相关关系,实现了在振幅可控条件下的内孤立波数值模拟。结果表明,在极限振幅范围内,数值模拟所得内孤立波波形均与MCC理论解吻合良好,而KdV(Korteweg-de Vries)和mKdV(modi-fied KdV)理论解只适用于小振幅的情况。同时,利用CFD数值模拟结果,对内孤立波诱导流速场特性进行了分析,结果表明内孤立波诱导水平速度在上层及波面下方流体层中垂向衰减很小,但在内界面与波面之间流体层中垂向衰减明显。 相似文献
4.
在RNGk-ε湍流模型下,基于Fluent平台中的DEFINE-SOURCE宏,结合KdV与eKdV理论编写相应程序,从粘性不可压缩流体的N-S方程出发,进行了基于质量源造波法的内孤立波数值模拟,并将所得模拟结果与物理实验结果、理论值及速度入口法与平板拍击法数值模拟结果进行了对比和分析。结果表明:质量源造波法所得波形与物理实验结果、理论值及速度入口法与平板拍击法数值模拟结果吻合较好,验证了本文所述质量源造波方法的可行性和有效性,且该方法对振幅水深比小于0.1和大于0.1的内孤立波均具有较好的适用性。此外,质量源造波法避免了动网格的使用、可用于研究速度边界未知的情况、耗时短、效率高、适应性强等优点为进一步研究内孤立波与海洋结构物的相互作用问题提供了一种新的实现方案。 相似文献
5.
6.
以三类内孤立波理论(Kd V、e Kd V和MCC)的适用性条件为依据,采用Morison和傅汝德-克雷洛夫公式分别计算Spar平台内孤立波水平力和垂向力,结合时域有限位移运动方程,建立了有限深两层流体中内孤立波与带分段式系泊索Spar平台相互作用的理论模型。以东沙群岛某海域实测内孤立波为对象,数值分析了在内孤立波作用下某经典式Spar平台的内孤立波动态载荷、运动响应及其系泊张力的变化特性。研究表明,内孤立波不仅会对Spar平台产生突发性冲击载荷,使其产生大幅度水平漂移运动,而且还会使其系泊张力显著增大。因此,在Spar平台等深海平台的设计应用中,内孤立波的影响不可忽视。 相似文献
7.
基于FLUENT的海洋内孤立波数值水槽模拟 总被引：3，自引：0，他引：3
基于FLUENT商业软件及其二次开发功能,在标准κ-ε湍流模型下,采用VOF方法追踪两层流体内界面,通过给定入口速度和水位的设置造波边界法,建立了可有效模拟弱非线性内孤立渡的分层流数值水槽,并与仿物理的双板造波方法进行了比较.采用设置边界法所造的波形与理论值符合较好,这为数值分析内孤立渡与海洋结构物相互作用问题提供了一条更加有效的途径. 相似文献
8.
张力腿平台内孤立波作用特性数值模拟 总被引：1，自引：1，他引：0
依据三类内孤立波理论KdV、eK dV和MCC的适用性条件,采用Navier-Stokes方程为流场控制方程,以内孤立波诱导上下层深度平均水平速度作为入口边界条件,建立了两层流体中内孤立波对张力腿平台强非线性作用的数值模拟方法。结果表明,数值模拟所得内孤立波波形及其振幅与相应理论和实验结果一致,并且在内孤立波作用下张力腿平台水平力、垂向力及力矩数值模拟结果与实验结果吻合。研究同时表明,张力腿平台内孤立波载荷由波浪压差力、粘性压差力和摩擦力构成,其中摩擦力很小,可以忽略;水平力的主要成分为波浪压差力和粘性压差力,粘性压差力与波浪压差力相比较小却不可忽略,流体粘性的影响较小;垂向力中粘性压差力很小,流体粘性影响可以忽略。 相似文献
9.
《中国海洋大学学报(自然科学版)》2016,(10)
本文选用RNGk-ε湍流模型封闭二维不可压缩N-S方程组,选用KdV、mKdV理论作为输入条件进行内孤立波造波模拟。运用流体模拟软件Fluent建立二维内波数值水槽,用动网格手段实现网格变形模拟物理边界造波法,用VOF方法进行密度分层流体的内界面追踪,对不同非线性强度的二相流内孤立波进行了数值模拟。并将数值模拟结果与KdV、mKdV理论波形以及内波试验水槽所造内孤立波进行对比,验证了此套造波方法在Fluent中进行内孤立波模拟的可行性。 相似文献
10.
将置于大尺度密度分层水槽上下层流体中的两块垂直板反方向平推,以基于MCC理论解的内孤立波诱导上下层流体中的层平均水平速度作为其运动速度,发展了一种振幅可控的双推板内孤立波实验室造波方法,并对内孤立波作用下浮式生产储油系统(FPSO)的载荷特性开展了系列实验。结果表明,无因次内孤立波水平力和力矩幅值均与先导内孤立子无因次振幅之间呈线性关系,其斜率与上下层流体深度比有关;在各种上下层流体深度比下,无因次内孤立波垂向力幅值与先导内孤立子振幅之间近似呈幂函数关系。 相似文献
11.
内孤立波具有振幅尺度大、能量集中的特点,其引起流场和密度场的迅速变化可能对海洋工程结构物以及水下潜体造成严重威胁。因此研究不同造波条件下生成的内孤立波运动的流场特征具有重要的学术意义和实际应用价值。采用直接数值模拟方法和给定的初始密度场密度跃迁函数,对重力塌陷激发内孤立波的运动过程进行研究,探讨了不同造波条件下,激发产生的内孤立波波型、涡度、振幅和水平速度等流场特征。结果表明:(1)直接模拟数值方法能够模拟内孤立波传播过程中的密度界面波型反转现象;(2)从定性和定量的角度,证实了不稳定内孤立波传播过程中存在能量的向后传递;(3)对于相同的台阶深度(水闸两侧初始密度界面的高度差),初始涡流保持相同,但是随着上下层水深比的减小,其强度下降显著;(4)台阶深度对初始涡流的垂直结构的影响要大于上下层水深比,且台阶深度对内孤立波的振幅、水平速度的影响显著。 相似文献
12.
Internal inlet for wave generation and absorption treatment 总被引：1，自引：0，他引：1
A new method of implementing, in two-dimensional (2-D) Navier–Stokes equations, a numerical internal wave generation in the finite volume formulation is developed. To our knowledge, the originality of this model is on the specification of an internal inlet velocity defined as a source line for the generation of linear and non-linear waves. The use of a single cell to represent the source line and its transformation to an internal boundary condition proved to be an interesting alternative to the common procedure of adding a mass source term to the continuity equation within a multi-cell rectangular region. Given the reduction of the source domain to a one-dimensional region, this simple new type of source introduced less perturbation than the 2-D source type. This model was successfully implemented in the PHOENICS code (Parabolic Hyperbolic Or Elliptic Numerical Integration Code Series). In addition, the volume of fluid (VOF) fraction was used to describe the free surface displacements. A friction force term was added to the momentum transport equation in the vertical direction, in order to enhance wave damping, within relatively limited number of cells representing the sponge layers at the open boundaries. For monochromatic wave, propagating on constant water depth, numerical and analytical results showed good agreements for free surface profiles and vertical distribution of velocity components. For solitary wave simulation, the wave shape and velocity were preserved; while, small discrepancy in the tailing edge of the free surface profiles was observed. The suitability of this new numerical wave generation model for a two source lines extension was investigated and proven to be innovative. The comparisons between numerical, analytical and experimental results showed that the height of the merging waves was correctly reproduced and that the reflected waves do not interact with the source lines. 相似文献
13.
Solitary waves have been commonly used as an initial condition in the experimental and numerical modelling of tsunamis for decades. However, the main component of a tsunami waves acts at completely different spatial and temporal scales than solitary waves. Thus, use of solitary waves as approximation of a tsunami wave may not yield realistic model results, especially in the coastal region where the shoaling effect restrains the development of the tsunami wave. Alternatively, N-shaped waves may be used to give a more realistic approximation of the tsunami wave profile. Based on the superposition of the sech2(*) waves, the observed tsunami wave profile could be approximated with the N-shaped wave method, and this paper presents numerical simulation results based on the tsunami-like wave generated based on the observed tsunami wave profile measured in the Tohoku tsunami. This tsunami-like wave was numerically generated with an internal wave source method based on the two-phase incompressible flow model with a Volume of Fluid (VOF) method to capture the free surface, and a finite volume scheme was used to solve all the governing equations. The model is first validated for the case of a solitary wave propagating within a straight channel, by comparing its analytical solutions to model results. Further, model comparisons between the solitary and tsunami-like wave are then made for (a) the simulation of wave run-up on shore and (b) wave transport over breakwater. Comparisons show that use of these largely different waveform shapes as inputs produces significant differences in overall wave evolution, hydrodynamic load characteristics as well as velocity and vortex fields. Further, it was found that the solitary wave uses underestimated the total energy and hence underestimated the run-up distance. 相似文献
14.
基于弱二维的KP方程，并结合南中国海东沙群岛附近内孤立波的观测资料，模拟了内孤立波的波-波相互倌用0数值结果较好的反应了内孤立波的二维特征，同时体现两个内孤立波波-波相互作用的非线性特征，即两波相交处相速随振幅的增大而变大。相比于一维的KdV方程，KP在内孤立波的仿真反演方面具有更大的优势。 相似文献
15.
安达曼海是内孤立波生成最多的海域之一,目前对其研究大多基于卫星遥感,缺乏基于现场观测资料的相关研究。本文通过2016年至2017年布放在安达曼海中部的锚系潜标对该海域内孤立波的方向和强度进行研究,结果表明在研究区域内孤立波主要向东北方向传播,最大振幅可达100 m。应用彻体力理论预测了研究海域内孤立波波源的分布,与遥感统计结果基本一致,并且波源位置更精确,可直观地给出不同波源激发内孤立波的能力。本文分别用浅水方程、深水方程和有限深方程对安达曼海中部内孤立波相速度进行模拟,结合卫星遥感分析发现该海域内孤立波的产生符合Lee波机制,在三种方程中有限深方程的模拟效果与潜标观测最相符。 相似文献
16.
The South China Sea (SCS) is a hot spot for oceanic internal solitary waves due to many factors, such as the complexity of the terrain environment. The internal solitary waves in the northern SCS mainl... 相似文献
17.
本文运用基于自适应网格的流体动力学开源软件Gerris,来建立基于Boussinesq近似下的二维不可压缩Euler方程组的数值模型,以模拟不同层化条件下稳定状态的完全非线性大振幅内孤立波。文中比较了完全非线性的用Gerris实现的Euler模型与弱非线性的KdV理论模型在刻画大振幅内孤立波结构及特征参数上的差异,说明在模拟大振幅内孤立波时,高阶非线性不应忽略。Euler模型模拟结果表明,完全非线性大振幅内孤立波的等密度面半宽度随深度变化,这使得基于KdV方程解析解、利用卫星SAR(Synthetic Aperture Radar)图像提取内孤立波极值间距来反演内波振幅的可行性存疑,需要重新评估。此外,本文用两组实测数据验证了用Gerris实现的Euler模型模拟大振幅内波的有效性。 相似文献
18.
Nonlinear internal waves(NIWs) are ubiquitous around the Kara Sea, a part of the Arctic Ocean that is north of Siberia. Three hot spot sources for internal waves, one of which is the Kara Strait, have been identified based on Envisat ASAR. The generation and evolution of the NIWs through the interactions of the tide and topography across the strait is studied based on a nonhydrostatic numerical model. The model captures most wave characteristics shown by satellite data. A typical inter-packets distance on the Barents Sea side is about 25 km in summer, with a phase speed about 0.65 m/s. A northward background current may intensify the accumulation of energy during generation, but it has little influence on the other properties of the generated waves. The single internal solitary wave(ISW) structure is a special phenomenon that follows major wave trains, with a distance about 5–8 km. This wave is generated with the leading wave packets during the same tidal period. When a steady current toward the Kara Sea is included, the basic generation process is similar, but the waves toward the Kara Sea weaken and display an internal bore-like structure with smaller amplitude than in the control experiment. In winter, due to the growth of sea ice, stratification across the Kara Strait is mainly determined by the salinity, with an almost uniform temperature close to freezing. A pycnocline deepens near the middle of the water depth(Barents Sea side), and the NIWs process is not as important as the NIWs process in summer. There is no fission process during the simulation. 相似文献
19.
In this paper, a modified dynamic coherent eddy model (DCEM) of large eddy simulation is applied to study internal solitary waves in a numerical flume. The model was verified by physical experiment and applied to investigate the potential influence factors on internal wave amplitude. In addition, we discussed the energy loss of internal solitary wave as well as hydrodynamics in the propagation. The results of our study show that (1) Step-depth is the most sensitive factor on wave amplitude for the “step-pool” internal wave generation method and the wave amplitudes obey a linear increase with step depth, and the increase rate is about 0.4. (2) Wave energy loss obeys a linear decrease with the propagation distance and its loss rate of large amplitude waves is smaller than that of small amplitude waves. (3) Loss of kinetic energy in wave valley is larger than that near the interface due to relative high fluctuating frequency. (4) Discovered boundary jet-flow can intensify the bottom shear, which might be one of the mechanisms of substance transportation, and the boundary layers of jet flows are easily influenced by the adjacent waves. 相似文献