共查询到20条相似文献，搜索用时 31 毫秒
1.
We describe experiments with multi-directional focused waves interacted with a vertical circular cylinder in a 3D wave basin. The focus of this study is on the run-up of multi-directional focused waves, wave forces, and wave pressures on the cylinder. Part I, the study on wave run-up, has already been presented by Li et al. (2012). In this paper, the analysis of the wave force on the vertical cylinder is presented.In this experiment, a cylinder with 0.25 m in diameter was adopted and different wave parameters, such as focused wave amplitude, peak frequency, frequency bandwidth and directional spreading index, are considered. The model scale kpa (kp is the wave number corresponding to peak frequency, a is the radium of the cylinder) varies from 0.32 to 0.65. The maximum forces of multi-directional focused wave on cylinder were measured and investigated. The results showed that the wave parameters have a significant influence on the wave force, and that the spatial profile of the surface of multi-directional focused wave can also affect its force on the cylinder, which is different from two-dimensional wave. In addition, the ‘secondary loading cycle’ phenomenon was also observed and discussed. In our experiments, the ‘secondary loading cycles’ occur when kA > 0.36 for all cases. While in some referred small scale experiments, the secondary load cycles are observed even for kA = 0.2, when the waves are longer enough. To larger model scale, the pronounced secondary load cycle occurs with larger wave steepness waves. 相似文献
2.
The wave transmission, reflection, and energy dissipation of the double rows of vertical piles suspending horizontal steel C shaped bars are experimentally and theoretically studied under normal regular waves. Different wave and structural parameters are investigated e.g. the wave length, the C shaped bars draft and spacing, the supporting piles diameter and spacing, and the space between the double rows. Also, the theoretical model based on an eigenfunction expansion method is developed to study the hydrodynamic breakwater performance. In order to examine the validity of the theoretical model, the theoretical results are compared with the experimental and theoretical results obtained by different authors. Comparison between experiments and predictions showed that theoretical model provides a good estimate to the different hydrodynamic coefficients when the friction factors of the upper and the lower parts are fU = 1.5 and fL = 0.75. The present breakwater physical model gives efficiency near other similar systems of different shapes. 相似文献
3.
The formation time of alongshore morphological variability in surf zone sand bars has long been known to differ from one beach to the other and from one post-storm period to another. Here we investigate whether the type of sea state, i.e. distant swell waves or locally generated short period wind sea, affects the formation time of the emerging alongshore topographic variability.A numerical modeling approach is used to examine the emergence of alongshore variability under different shore-normal wave forcing. A research version of Delft3D, operating on the time-scale of wave groups, is applied to a schematised bathymetry with a single bar. The model is then used to investigate several wave scenarios, examining the impact of peak period, frequency spread and directional spread on the formation time of alongshore variability.Results show that an increase in wave period has a large effect, changing the formation time up to O (250%) in case the wave period is changed from a representative value for the Dutch coast (Tp ~ 5–6 s) to an Australian South East coast value (Tp ~ 10–12 s). In contrast, modifications in the directional and frequency spread of the wave field result only in a minor change in the formation time.Examination of hydrodynamics and potential sediment transport shows that the variations in formation time are primarily related to changes in the magnitude of the time-averaged flow conditions. Variations in the magnitude of very low frequency (f < 0.004 Hz) or infragravity (0.004 < f < 0.04 Hz) surf zone flow velocities do not affect the mean sediment transport capacity. Consequently the formation speed of patterns is primarily governed by positive feedback between mean flow and morphology, and low frequency flow fluctuations are of minor importance.These findings indicate that the development of alongshore topographic variability may be faster at swell dominated open coasts, primarily due to the occurrence of longer period swell. Also, at a given site, the arrival of a long wave period swell after a storm can accelerate the emergence of variability. 相似文献
4.
A lift based cycloidal wave energy converter (WEC) was investigated using potential flow numerical simulations in combination with viscous loss estimates based on published hydrofoil data. This type of wave energy converter consists of a shaft with one or more hydrofoils attached eccentrically at a radius. The main shaft is aligned parallel to the wave crests and submerged at a fixed depth. The operation of the WEC as a wave-to-shaft energy converter interacting with straight crested waves was estimated for an actual ocean wave climate. The climate chosen was the climate recorded by a buoy off the north-east shore of Oahu/Hawaii, which was a typical moderate wave climate featuring an average annual wave power PW = 17 kWh/m of wave crest. The impact of the design variables radius, chord, span and maximum generator power on the average annual shaft energy yield, capacity factor and power production time fraction were explored. In the selected wave climate, a radius R = 5 m, chord C = 5 m and span of S = 60 m along with a maximum generator power of PG = 1.25 MW were found to be optimal in terms of annual shaft energy yield. At the design point, the CycWEC achieved a wave-to-shaft power efficiency of 70%. In the annual average, 40% of the incoming wave energy was converted to shaft energy, and a capacity factor of 42% was achieved. These numbers exceeded the typical performance of competing renewables like wind power, and demonstrated that the WEC was able to convert wave energy to shaft energy efficiently for a range of wave periods and wave heights as encountered in a typical wave climate. 相似文献
5.
An intra-annual investigation of the fugacity of CO2 (fCO2) has been conducted in surface waters of the north-eastern shelf of the Gulf of Cádiz (SW Iberian Peninsula) in four cruises made in 2006 and 2007. Intra-annual variability of fCO2 was assessed and is discussed in terms of mixing, temperature and biology. In the study area of the shelf, thermodynamic control over fCO2 predominates from early May to late November, and this is opposite and similar in magnitude to the net biological effect. However, biological control over fCO2 predominates during winter. The results suggest that surface waters in the coastal area are under-saturated with respect to atmospheric CO2 during most of the year; therefore they represent a sink for atmospheric CO2 between November and May (? 1.0 mmol m? 2 day? 1), but a weak source in June (1.3 mmol m? 2 day? 1). In contrast, the coastal ecosystems studied (the lower estuary of Guadalquivir Estuary and Bay of Cádiz) acted as a weak sink for atmospheric CO2 during February (? 1.3 mmol m? 2 day? 1) and as a source between May and November (2.6 mmol m? 2 day? 1). The resulting mean annual CO2 flux in the north-eastern shelf of the Gulf of Cádiz was ? 0.07 mol m? 2 year? 1 (? 0.2 mmol m? 2 day? 1), indicating that the area acts as a net sink on an annual basis. 相似文献
7.
We have employed laboratory and numerical experiments in order to investigate propagation of waves in both long and short-crested wave fields in deep water. For long-crested waves with steepness, ϵ = kcac = 0.1 (a fairly extreme case), reliable prediction can be performed with the modified nonlinear Schrödinger equation up to about 40 characteristic wavelengths. For short-crested waves the accuracy of prediction is strongly reduced with increasing directional spread. 相似文献
8.
Based on the linear potential flow theory and matching eigen-function expansion technique, an analytical model is developed to investigate the hydrodynamics of two-dimensional dual-pontoon floating breakwaters that also work as oscillating buoy wave energy converters (referred to as the integrated system hereafter). The pontoons are constrained to heave motion independently and the linear power take-off damping is used to calculate the absorbed power. The proposed model is verified by using the energy conservation principle. The effects of the geometrical parameters on the hydrodynamic properties of the integrated system, including the reflection and transmission coefficients and CWR (capture width ratio, which is defined as the ratio of absorbed wave power to the incident wave power in the device width). It is found that the natural frequency of the heave motion and the spacing of the two pontoons are the critical factors affecting the performance of the integrated system. The comparison between the results of the dual-pontoon breakwater and those of the single-pontoon breakwater shows that the effective frequency range (for condition of transmission coefficient KT < 0.5 and the total capture width ratio ηtotal > 20%) of the dual-pontoon system is broader than that of the single-pontoon system with the same total volume. For the two-pontoon system, the effective frequency range can be broadened by decreasing the draft of the front pontoon within certain range. 相似文献
9.
《Marine Geology》2007,236(1-2):15-26
The South American coast between Brazil and Venezuela is affected by longshore migrating mud banks derived from the fine-grained Amazon sediment discharge. Onshore mud migration prevails over shallow ‘bank’ areas alternating alongshore with deeper ‘inter-bank’ areas. The transport on the inner shelf, and attachment to the shoreline, of this migrating mud has been attributed mainly to wind waves. However, the lack of in situ data on waves hampers understanding of the relationship between waves and mud dynamics. A 44-yr record (1960–2004) of the ERA-40 wave dataset generated by the European Centre for Medium-Range Weather Forecasts (ECMWF) was used, in conjunction with field investigations in French Guiana, to define both event-scale and longer-term patterns of mud mobilisation induced by waves. The ratio H03 / T2, combining wave height H and period T, and the angle of wave incidence α, were singled out as the most relevant parameters for describing wave forcing. Typical ‘bank’ and ‘inter-bank’ profiles and corresponding mud densities, and a 3-month record of changes in the thickness of the fluid mud layer in an estuarine navigation channel were monitored by echo-sounding from October 2002 to January 2003. An 80-day record of bed-level changes in the intertidal zone was obtained from August to November 2004 using a pressure transducer. The results on the wave regime of French Guiana confirm a distinctly seasonal pattern, and highlight an increase in H03 / T2 over the 44-yr period related to an increase in trade-wind velocities determined from corresponding trends in Atlantic wind pseudo-stress off the South American coast. Wave forcing over bank areas leads to the liquefaction of a 1–3 m-thick layer of mud that is transported onshore (and alongshore by the longshore component of wave energy). The episodic nature of high wave energy events generally results in the formation of mud bar features from the shoreward mobilisation of gel-like fluid mud. The effect of waves on mud is particularly marked following long periods of low energy, and especially at the onset of the high wave energy season (October to May), when even moderate wave energy events can lead to significant mobilisation of mud.Significant phases of increased wave energy are attended by higher long-term (annual) rates of longshore mud bank migration but the correlation is rather poor between the wave forcing parameter H03 / T2 and migration rates because stronger wave forcing is generally associated with low angles of wave incidence. This suggests a complementary role of other hydrodynamic mechanisms, such as geostrophic and tidal currents, in longshore mud bank migration. 相似文献
10.
《Deep Sea Research Part I: Oceanographic Research Papers》2005,52(6):1001-1019
This study explores the changes in the surface water fugacity of carbon dioxide (fCO2) and biological carbon uptake in two Southern Ocean iron fertilisation experiments with different hydrographic regimes. The Southern Ocean Iron Release Experiment (SOIREE) experiment was carried out south of the Antarctic Polar Front (APF) at 61°S, 141°E in February 1999 in a stable hydrographic setting. The EisenEx experiment was conducted in a cyclonic eddy north of the APF at 48°S, 21°E in November 2000 and was characterised by a rapid succession of low to storm-force wind speeds and dynamic hydrographic conditions. The iron additions promoted algal blooms in both studies. They alleviated algal iron limitation during the 13-day SOIREE experiment and probably during the first 12 days of EisenEx. The fCO2 in surface water decreased at a constant rate of 3.8 μatm day−1 from 4 to 5 days onwards in SOIREE. The fCO2 reduction was 35 μatm after 13 days. The evolution of surface water fCO2 in the iron-enriched waters (or ‘patch’) displayed a saw tooth pattern in EisenEx, in response to algal carbon uptake in calm conditions and deep mixing and horizontal dispersion during storms. The maximum fCO2 reduction was 18–20 μatm after 12 and 21 days with lower values in between. The iron-enriched waters in EisenEx absorbed four times more atmospheric CO2 than in SOIREE between 5 and 12 days, as a result of stronger winds. The total biological uptake of inorganic carbon across the patch was 1389 ton C (±10%) in SOIREE and 1433 ton C (±27%) in EisenEx after 12 days (1 ton=106 g). This similarity probably reflects the comparable size of the iron additions, as well as algal growth at a similar near-maximum growth rate in these regions. The findings imply that the different mixing regimes had less effect on the overall biological carbon uptake across the iron-enriched waters than suggested by the evolution of fCO2 in surface water. 相似文献
11.
Investigation of the bottom slope effects on the nonlinear transformation of irregular waves, which are generated based on JONSWAP spectra, is carried out in a physical wave flume with three slopes (β = 1/15, 1/30, 1/45). The slope effects on the estimation of representative wave height are examined first. To obtain a better estimation of wave height, the slope effect should be considered when slope is larger than 1/30. The nonlinear parameters (bicoherence, skewness and asymmetry) are estimated by using the wavelet-based bispectrum, and the empirical formulae regarding these nonlinear parameters as a function of the local Ursell number are derived based on the present data measured on each slope. The results indicate that the slopes have a negligible effect on the variations of the skewness. The fitted coefficients of the formulae for the other parameters on slope β = 1/15 are clearly different from the results on the slopes β = 1/30 and 1/45, indicating that slope influence on the parameterization cannot be ignored when β > 1/30. Hence, new formulae considering the slope effect are presented. Furthermore, the empirical formulae for the data in surf zone are recommended. 相似文献
12.
《Deep Sea Research Part I: Oceanographic Research Papers》2006,53(3):449-473
Mode-1 internal tides were observed the western North Atlantic using an ocean acoustic tomography array deployed in 1991–1992 centered on 25°N, 66°W. The pentagonal array, 700-km across, acted as an antenna for mode-1 internal-tides. Coherent internal-tide waves with O(1 m) displacements were observed traveling in several directions. Although the internal tides of the region were relatively quiescent, they were essentially phase locked over the 200–300 day data record lengths. Both semidiurnal and diurnal internal waves were detected, with wavenumbers consistent with those calculated from hydrographic data. The M2 internal-tide energy flux was estimated to be about 70 W m−1, suggesting that mode-1 waves radiate 0.2 GW of energy, with large uncertainty, from the Caribbean island chain at this frequency. A global tidal model (TPXO 5) suggested that 1–2 GW is lost from the M2 barotropic tide over this region, but the precise value was uncertain because the complicated topography makes the calculation problematic. In any case, significant conversion of barotropic to baroclinic tidal energy does not occur in the western North Atlantic basin. It is apparent, however, that mode-1 internal tides have very weak decay and retain their coherence over great distances, so that ocean basins may be filled up with such waves. Observed diurnal amplitudes were an order of magnitude larger than expected. The amplitude and phase variations of the K1 and O1 constituents observed over the tomography array were consistent with the theoretical solutions for standing internal waves near their turning latitude. The energy densities of the resonant diurnal internal waves were roughly twice those of the barotropic tide at those frequencies. 相似文献
13.
Ocean surface gravity waves play a major role in many engineering and environmental problems, both in the open ocean and in coastal zones. Therefore, it is essential to improve our knowledge on spatial and temporal variability of wave climate. This study aims at investigating this variability in the North-East Atlantic Ocean (25°W–0°W and 30°N–60° N), using a 57-year hindcast (1953–2009) obtained with a spectral wave model forced with reanalysis wind fields. The hindcast analysis reveals firstly strong seasonal fluctuations of wave climate, with winters characterized by large and long-period waves of mean direction spreading from south-west to north-west, and summers characterized by smaller and shorter-period waves originating from norther directions. From northern (55°N) to southern (35°N) latitudes, the significant wave height (Hs) decreases by roughly 40%, the mean wave direction (Mwd) rotates clockwise by about 25% while the peak period (Tp) only grows by 5%. These three parameters also exhibit a strong inter-annual variability, particularly when winter-means (from 1st of December to 1st of April) are considered. Linear trend analysis over the studied period shows spatially variable long-term trends, with a significant increase of Hs (up to 0.02 m yr?1) and a counterclockwise shift of Mwd (up to ?0.1° yr?1) at northern latitude, contrasting with a fairly constant trend for Hs and a clockwise shift of Mwd (up to +0.15° yr?1) at southern latitudes. Long-term trends of Tp are less significant, with still a slight increase in the north-eastern part of the study area (up to +0.01 s yr?1). Eventually, a comparison between the inter-annual variability of the winter-means of the three selected wave parameters and the North Atlantic Oscillation (NAO) reveals: (1) a strong positive correlation between Hs and the NAO index at northern latitudes (correlation coefficient up to R = 0.91) and a significant negative correlation at southern latitudes (up to R = ?0.6); (2) no significant correlation for Mwd north of 40°N and a clear positive correlation southward of 40°N (up to R = 0.8) and (3) a northward increasing correlation for Tp (up to R = 0.8). Long-term trends for Hs, Mwd and Tp are finally explained by a significant increase in the NAO index over the studied period. 相似文献
14.
Using Boussinesq scaling for water waves while imposing no constraints on rotationality, we derive and test model equations for nonlinear water wave transformation over varying depth. These use polynomial basis functions to create velocity profiles which are inserted into the basic equations of motion keeping terms up to the desired Boussinesq scaling order, and solved in a weighted residual sense. The models show rapid convergence to exact solutions for linear dispersion, shoaling, and orbital velocities; however, properties may be substantially improved for a given order of approximation using asymptotic rearrangements. This improvement is accomplished using the large numbers of degrees of freedom inherent in the definitions of the polynomial basis functions either to match additional terms in a Taylor series, or to minimize errors over a range. Explicit coefficients are given at O(μ2) and O(μ4), while more generalized basis functions are given at higher order. Nonlinear performance is somewhat more limited as, for reasons of complexity, we only provide explicitly lower order nonlinear terms. Still, second order harmonics may remain good to kh ≈ 10 for O(μ4) equations. Numerical tests for wave transformation over a shoal show good agreement with experiments. Future work will harness the full rotational performance of these systems by incorporating turbulent and viscous stresses into the equations, making them into surf zone models. 相似文献
15.
A. Warn-Varnas J. Hawkins K.G. Lamb S. Piacsek S. Chin-Bing D. King G. Burgos 《Ocean Modelling》2010,31(1-2):9-27
A high resolution modeling study is undertaken, with a 2.5-dimensional nonhydrostatic model, of the generation of internal waves induced by tidal motion over the ridges in Luzon Strait. The model is forced by the barotropic tidal components K1, M2, and O1. These tidal components, along with the initial density field, were extracted from data and models. As the barotropic tide moves over the Luzon Strait sills, there is a conversion of barotropic tidal energy into baroclinic tidal energy. Depressions are generated that propagate towards the Asian Seas International Acoustics Experiment (ASIAEX) test site on the Chinese continental shelf. Nonlinear effects steepen the depressions, frequency and amplitude dispersion set in, and disintegration into large amplitude solitary waves occurs. The effects of varying the initial density field, tidal component magnitudes, as well as adding a steady background current to represent the occasional excursions of the Kuroshio Current into the strait, are considered.Depressions are generated at each of the two sills in Luzon Strait which radiate away, steepening and evolving into internal solitary wave trains. Baroclinic fluxes of available potential energy, kinetic energy and linear are calculated for various parameter combinations. The solitary wave trains produced in the simulations generally consist of large amplitude wave trains alternating with small amplitude wave trains. During strong tidal flow, Kelvin–Helmholtz type instabilities can develop over the taller double-humped sill. The solitary waves propagating towards the ASIAEX test site have been observed to reach amplitudes of 120–250 m, depending on the tidal strength. ASIAEX observations indicate amplitudes up to 150 m and the Windy Island Experiment (WISE) measurements contain magnitudes over 200 m. The model results yield solitary wave amplitudes of 70–300 m and half widths of 0.60–3.25 km, depending on parameter values. These are in the range of observations. Measurements by Klymak et al. (2006), in the South China Sea, exhibit amplitudes of 170 m, half widths of 3 km and phase speeds of 2.9 m s?1. Model predictions indicate that the solitary waves making up the wave packet each experience different background currents with strong near surface shear.The energy in the leading soliton of the large amplitude wave trains ranges between 1.8 and 9.0 GJ m?1. The smaller value, produced using barotropic tidal currents based on the Oregon State University data base, is the same as the energy estimated to be in a solitary wave observed by Klymak et al. (2006). Estimates of the conversion of barotropic tidal energy into radiating internal wave energy yield conversion rates ranging between 3.6% and 8.3%. 相似文献
16.
A fully nonlinear Boussinessq-type model with several free coefficients is considered as a departure point. The model is monolayer and low order so as to simplify numerical solvability. The coefficients of the model are here considered functions of the local water depth. In doing so, we allow to improve the dispersive and shoaling properties for narrow banded wave trains in very deep waters. In particular, for monochromatic waves the dispersion and shoaling errors are bounded by ~ 2.8% up to kh = 100, being k the wave number and h the water depth. The proposed model is fully nonlinear in weakly dispersive conditions, so that nonlinear wave decomposition in shallower waters is well reproduced. The model equations are numerically solved using a fourth order scheme and tested against analytical solutions and experimental data. 相似文献
17.
《Coastal Engineering》2006,53(9):781-792
This paper presents results of a series of detailed measurements of geometric and migrating characteristics of ripples superimposed upon sandwaves under the action of combined waves and currents. Velocity measurements within the fluid, surface wave characteristics and 3D mapping of the bottom were recorded with an Acoustic Doppler Velocimeter (ADV), an acoustic water level sensor and a 32 composite element array of sub-aquatic acoustic sensors, respectively. Bottom records were statistically analyzed to obtain height, length and migration rates of ripples. Experiments examined ripple heights and wavelengths for the mobility factors (as defined in Eq. (4)) and the Reynolds wave number within the ranges 10 < ψ < 88 and 16 × 103 < Rew < 5 × 105, respectively. Measured values were compared with laboratory and field data together with semi-empirical and analytical formulae from the literature. Good correlation was obtained when plotting measured ripple length and length in dimensionless form as a function of the Reynolds wave number Rew. Under a given hydraulic condition, it was observed that ripples with different geometric characteristics may coexist at different locations over the sandwave. Ripple steepness is presented as a function of the Shields parameter although characterized with rather large scatter. Finally, average ripple migration speed is presented as a function of the Shields parameter and the mobility number. 相似文献
18.
Probability distribution of wave heights attenuated by salt marsh vegetation during tropical cyclone
Zero-crossing wave heights, obtained from the field measurement of random waves propagating through salt marsh vegetation (Spartina alterniflora) during a tropical storm, were analyzed to examine their probability distribution. Wave data (significant wave heights up to 0.4 m in 0.8 m depth) were collected over a two-day period along a 28 m transect using three pressure transducers sampling at 10 Hz. Wave height distribution was observed to deviate from the Rayleigh distribution. The observed probability densities of the larger wave heights were reduced significantly by vegetation, producing wave heights lower than those predicted by the Rayleigh distribution. Assuming Rayleigh distributed wave heights for the incident waves to the vegetation patch, existing vegetation-induced wave attenuation formulations are used to derive a special form of two-parameter Weibull distribution for wave heights in the inundated wetland. The scale parameter of the distribution is theoretically shown to be a function of the shape parameter, which agrees with the measurements, effectively reducing the proposed distribution to a one-parameter type. The derived distribution depends on the local parameters only and fits well to the observed distribution of wave heights attenuated by vegetation. Empirical relationships are developed to estimate the shape parameter from the local wave parameters. 相似文献
19.
《Coastal Engineering》2005,52(9):745-770
New experiments were carried out in the Large Oscillating Water Tunnel of WL|Delft Hydraulics (scale 1:1) using asymmetric 2nd-order Stokes waves. The main aim was to gain a better understanding of size-selective sediment transport processes under oscillatory plane-bed/sheet-flow conditions. The new data show that for uniform sand sizes between 0.2 < D < 1.0 mm, measured net transport rates are hardly affected by the grain size and are proportional to the third-order velocity moment. However for finer grains (D = 0.13 mm) net sand transport rates change from the ‘onshore’ direction into the ‘offshore’ direction in the high velocity range. A new measuring technique for sediment concentrations, based on the measurement of electro-resistance (see [McLean, S.R., Ribberink, J.S., Dohmen-Janssen, C.M. and Hassan, W.N.M., 2001. Sediment transport measurements within the sheet flow layer under waves and currents. J. Waterw., Port, Coast., Ocean Eng., ISSN 0733-950X]), was developed further for the improved measurement of sediment dynamics inside the sheet-flow layer. This technique enabled the measurements of particle velocities during the complete wave cycle. It is observed that for long period waves (T = 12.0 s), time-dependent concentrations inside the sheet-flow layer are nearly in phase with the time-dependent flow velocities. As the wave period decreases, the sediment entrainment from the bed as well as the deposition process back to the bed lags behind the wave motion more and more. The new data show that size-gradation has almost no effect on the net total transport rates, provided the grain sizes of the sand mixture are in the range of 0.2 < D < 1.0 mm. However, if very fine grains (D = 0.13 mm) are present in the mixture, net total transport rates of graded sand are generally reduced in comparison with uniform sand with the same D50. The transport rates of individual size fractions of a mixture are strongly influenced by the presence of other fractions in a mixture. Fine particles in sand mixtures are relatively less transported than in that uniform sand case, while the opposite occurs for coarse fractions in a mixture. The relative contribution of the coarse grains to the net total transport is therefore larger than would be expected based on their volume proportion in the original sand mixture. This partial transport behaviour is opposite to what is generally observed in uni-directional (e.g. river) flows. This is caused by vertical sorting of grain sizes in the upper bed layer and in the sheet flow and suspension layers. Kinematic sorting is believed to be responsible for the development of a coarse surface layer on top of a relatively fine sub-layer, providing in this way a relatively large flow exposure for the coarser sizes. Furthermore fine grains are suspended more easily than coarse grains to higher elevations in the flow where they are subject to increasing phase-lag effects (settling lags). The latter also leads to reduced net transport rates of these finer sizes. 相似文献