共查询到20条相似文献，搜索用时 31 毫秒
1.
KK型管节点是自升式平台桁架式桩腿中的一种管节点，其应力集中系数是影响桩腿疲劳寿命的重要参数。应力集中系数与管节点的几何形式密切相关，为分析KK型管节点应力集中系数对几何参数的敏感性，利用ANSYS软件对某KK型管节点进行几何参数化建模，利用有限元数值模拟方法对各工况下的热点应力进行分析，并分别计算各相应工况下的名义应力，然后将热点应力与名义应力相比得到不同几何参数下的热点应力集中系数。对计算结果进行整理分析，得到了KK型管节点应力集中系数对无量纲几何参数的敏感性规律。结果表明，应力集中系数与撑杆受力状态、管节点结构形式有关，在满足结构布置、建造工艺和其他安全性指标的前提下，分析结果能够为KK型管节点的结构设计和疲劳分析提供技术支撑。 相似文献
2.
以某新型深水半潜式钻井平台为分析对象,依据三维绕射理论计算单位波幅下波浪诱导载荷,通过建立三维有限元模型计算完成了热点应力响应。运用热点应力的谱分析法计算得到危险节点的疲劳寿命,并进一步分析了各个短期海况和不同浪向对节点总的疲劳损伤度的贡献。研究结果表明,危险节点的疲劳寿命都满足设计寿命要求;在各种中低海况下,疲劳损伤主要来自于平均跨零周期在6 s附近,有义波高转大的短期海况;平台关键连接部位的疲劳损伤主要是在横浪和斜浪状态下产生的,并且对某单一方向的波浪非常敏感。此研究对该类型平台的连接处结构设计和疲劳分析方法有参考意义。 相似文献
3.
Chen Tieyun Zhang Huiyuan Proefessor Shanghai Jiao Tong University Shanghai
Engineer Shenzhen Shipbuilding Trading Co. LTD Shenzhen 《中国海洋工程》1993,(4)
- The formulation for the stress concentration matrix of multiplanar tubular joint with braces subjected to combined load is established in this paper. The formulations for SCF values of multiplanar tubular joints are compared with those by Wordsworth and Efthymiou. The stiffening effect and load-interaction effect are discussed. A spatial offshore jacket with braces subjected to combined load is computed as a numerical example. The maximum stress of each multiplanar tubular joint and its location are found through SCF matrix. Finally, the difference between the maximum stresses of multiplanar tubular joints and their corresponding uniplanar tubular joints are discussed. 相似文献
4.
张力腿平台局部节点强度可靠度分析方法 总被引：1，自引：0，他引：1
局部节点可靠度分析对张力腿平台(TLP)整体安全性评估具有重要意义。提出了一个TLP平台局部节点可靠度的分析方法,首先对TLP平台整体进行分析,统计局部节点各种失效模式并得到典型失效模式及对应的典型荷载工况;然后应用改进的子模型技术对TLP平台局部节点进行极限承载能力分析,确定了局部节点在典型荷载工况下的极限承载力;对局部节点极限承载力及南海某区域的波浪荷载进行统计分析,得到其概率统计特性;在此基础上计算了TLP平台局部节点对应典型失效模式下的可靠度指标。通过算例分析表明,该TLP平台各节点可靠度指标值均大于3.1;立柱与浮箱连接节点在不同荷载工况下失效模式不同,而立柱与甲板连接节点易发生管交汇处剪切破坏。为TLP平台的安全性评估提供了一种有效的分析方法,具有一定的理论价值及实用价值。 相似文献
5.
疲劳破坏是海洋结构物发生破坏的一种主要形式,深水半潜平台在海上运输、作业、停滞时会受到交变的风、浪、流载荷作用,进而引起结构关键节点处的疲劳损伤,影响平台安全性。以"海洋石油981"半潜钻井平台为研究对象,利用光纤光栅应变传感器对结构高应力区进行应力监测,获取测点处应力时历数据。将监测位置划分为四个监测板块,采用四点雨流计数法对测点应力进行处理,得到以离散形式给出的应力循环幅度与相应循环周次。参照DNV《海上钢结构疲劳设计规范》推荐的S-N曲线,基于Miner线性疲劳累计损伤原则,得到各个测点处的总体疲劳损伤度。选取具有最大疲劳损伤度的危险测点,并结合海上实测总时长,预测半潜平台的总体疲劳寿命。 相似文献
6.
In the present study, the dynamic and fatigue characteristics of two types of stress joints are investigated under ocean environmental condition. Connected with the riser and the platform, stress joint at the vessel hang-off position should be one of the main critical design challenges for a steel catenary riser (SCR) in deepwater. When the riser is under a high pressure and deepwater working condition, the stress state for the joint is more complex, and the fatigue damage is easy to occur at this position. Stress joint discussed in this paper includes two types: Tapered Stress Joint (TSJ) and Sleeved Stress Joint (SSJ), and multiaxial fatigue analysis results are given for comparison. Global dynamic analysis for an SCR is performed first, and then the local boundary conditions obtained from the previous analysis are applied to the stress joint FE model for the later dynamic and multiaxial fatigue analysis. Results indicate that the stress level is far lower than the yield limit of material and the damage induced by fatigue needs more attention. Besides, the damage character of the two types of stress joints differs: for TSJ, the place where the stress joint connects with the riser is easy to occur fatigue damage; for SSJ, the most probable position is at the place where the end of the inner sleeve pipe contacts with the riser body. Compared with SSJ, TSJ shows a higher stress level but better fatigue performance, and it will have a higher material cost. In consideration of various factors, designers should choose the most suitable type and also geometric parameters. 相似文献
7.
This paper presents an analytical solution for the dynamic behavior of both the platform and tethers in the tension leg platform system when the platform system is subjected to the wave-induced surge motion and the flow-induced drag motion. Along with the analysis the coupling problem of a two dimensional tension leg platform interacting with a monochromatic linear wave train in an inviscid and incompressible fluid is being considered. The scattering problem and radiation problem are first solved independently and then combined together to resolve for all unknowns. The dynamic behavior of the platform and tethers was further solved based on these solutions. The material property and the dimensional effect for the tether incorporated in the tension leg platform system are both taken into account in the analytical analysis. Corresponding to the variation of material properties and tether dimensions, it was found that the dynamic behavior of both the tether of tension leg platform and the platform itself is closely related to the material property and the dimension of the tether. 相似文献
8.
Analysis of wave-induced liquefaction in seabed deposits of silt 总被引：1，自引：0，他引：1
The dynamic stress introduced in half elastic space by wave loading is characterized by the equation between the magnitude of half cyclic axial stress and cyclic torsion shear stress and the principal stress,whose direction rotates continuously and compression stress on seabed can be calculated by the use of small amplitude wave theory.With relationship curves of saturated silt of liquefaction cycles and cyclic stress ratios obtained by cyclic triaxial-torsional coupling shear tests and curve fitting method to different data points of relative density,it is suggested that the cyclic stress ratio corresponding to constant liquefaction impedance be taken as the critical cyclic stress ratio which implies liquefaction.There exists a linear relationship between critical cyclic stress ratio and relative density under different relative densities.Empirical formula for critical cyclic stress ratios of seabed liquefaction induced by wave loading under different relative densities is established.The possibility of seabed silt liquefaction and its influence factors are analyzed based on the small-amplitude wave theory and the data acquired in laboratory tests. 相似文献
9.
10.
针对目前小油田早期生产中存在的不足,提出一种适用于浅水海域的新型张力腿式储油处理平台,该平台主要由储油箱、浮箱、吸力桩、系泊链和甲板结构构成,具备原油处理和储存功能。应用非线性时域耦合分析法,研究了有义波高、平均波周期、水深对该平台的运动响应和系泊链张力的影响。计算结果表明,波高对平台动力响应有较大影响,有义波高每增加0.4 m,平台水平位移相应增加0.408 m,而系泊链力随有义波高的增加呈准线性增大;波周期对平台水平运动影响显著,平均波周期从6.5 s逐级变化至8.5 s时,最大水平位移自3.760 m渐增至5.467 m,而波周期对系泊链力影响较小,变化率一般小于10%;该新型平台对水深大于20 m的浅水海域有良好的动力特性,而对水深小于20 m的海域却表现异常。因此,该新型张力腿式平台能满足水深不小于20 m浅海区的油田早期生产需要。 相似文献
11.
Felipe Alexander Vargas Bazán Edison Castro Prates de Lima Marcos Queija de Siqueira Elizabeth Frauches Netto Siqueira Carlos Alberto Duarte de Lemos 《Applied Ocean Research》2011,33(4):344-365
In riser structural systems, the region where the riser is connected to the platform is critical due to the development of high stress levels. To reduce the stress concentration in this region, bend stiffeners and stress joints are used in order to provide a gradual stiffness transition between the riser and the platform. The present paper presents an optimization design approach for bend stiffeners and stress joints, using a slender beam procedure for the connection joint analysis and an evolution strategies multi-objective optimization algorithm. This approach produces similar results when compared to a finite element analysis of the complete riser, but with significant reduction of computational costs. Numerical examples are presented, showing the efficiency and robustness of the suggested methodology. 相似文献
12.
Interfacial waves and wave-induced tangential stress are studied for geostrophic small amplitude waves of two-layer .uid with a top free surface and a .at bottom. The solutions were deduced from the general form of linear .uid dynamic equations of two-layer .uid under the f -plane approximation, and wave-induced tangential stress were estimated based on the solutions obtained. As expected, the solutions derived from the present work include as special cases those obtained by Sun et al. (2004. Science in China, Ser. D, 47(12): 1147–1154) for geostrophic small amplitude surface wave solutions and wave-induced tangential stress if the density of the upper layer is much smaller than that of the lower layer. The results show that the interface and the surface will oscillate synchronously, and the in.uence of the earth’s rotation both on the surface wave solutions and the interfacial wave solutions should be considered. 相似文献
13.
A new normal mode spectral analysis method is presented for calculating r.m.s. riser deflections, bending stresses and lower ball joint angles. Forces on the riser consist of: (a) non-linear fluid drag taking account of the relative velocity due to tethered buoyant platform (TBP) motion, riser elastic deflection and wave induced fluid velocity, (b) wave induced fluid acceleration, (c) inertia forces due to TBP acceleration, and (d) buoyancy. The non-linear fluid drag forces are linearized using Tung and Wu's approximation based on the r.m.s. relative fluid velocity and current. A wide range of results is presented for risers in water depths up to 1000 m and it is observed that 6 normal modes are sufficient for calculating bending stresses. A static analysis is also presented for bending stresses due to wave and current induced drag forces and riser offset. 相似文献
14.
Interfacial waves and wave-induced tangential stress are studied for geostrophic small amplitude waves of two-layer fluid with a top free surface and a flat bottom. The solutions were deduced from the general form of linear fluid dynamic equations of two-layer fluid under the f-plane approximation, and wave-induced tangential stress were estimated based on the solutions obtained. As expected, the solutions derived from the present work include as special cases those obtained by Sun et al. (2004. Science in China, Ser. D, 47(12):1147-1154) for geostrophic small amplitude surface wave solutions and wave-induced tangential stress if the density of the upper layer is much smaller than that of the lower layer. The results show that the interface and the surface will oscillate synchronously, and the influence of the earth''s rotation both on the surface wave solutions and the interfacial wave solutions should be considered. 相似文献
15.
浮体运动是引起钢悬链式立管(steel catenary riser,简称SCR)动态响应和疲劳损伤的关键因素,目前研究SCR问题时,为简化计算往往仅考虑平台一阶运动,忽略二阶运动影响。而实际上不同浮体结构的二阶运动响应特征明显,拟以SCR服役张力腿平台(tension leg platform,简称TLP)为例,探讨浮体二阶运动对SCR触地区动态响应的影响。建立考虑海床刚度退化的管土作用模型以改进现有的CABLE3D RSI程序,通过编写程序接口,将有限元分析得到的平台实际运动响应导入,研究平台不同运动作用下SCR触地区的位移、动力响应及疲劳分布情况。根据波流作用方向将TLP二阶慢漂运动分为近端和远端漂移两种工况,发现二阶运动下立管与海床的作用范围会增大,且触地区不仅发生高频小幅振荡运动,同时伴随低频大幅运动响应;平台远端漂移时,管内张力敏感程度高,而近端漂移时触地区的弯矩显著增大,都会不同程度提高触地区的疲劳损伤率。研究可为服役不同浮体的SCR响应预测与疲劳分析提供参考和借鉴。 相似文献
16.
Nonlinear Random Motion Analysis of A Tension Leg Platform Considering the Set-down Motion of A Floating Body 总被引：1，自引：1，他引：0
The dynamic analysis of a Tension Leg Platform (TLP) in random wave is investigated by considering the set-down of a floating body. The nonlinear restoring stiffness is derived with the set-down motion of a floating body and the coupled motion of the tension leg and platform and the differential equations of the motion are established. The study focuses on the influence of the set-down motion on the nonlinear response of the platform. By considering different significant wave heights and currents, motion responses of the platform are calculated and compared. The analysis shows that the set-down motion significantly increases the heave motion with low frequency and the equilibrium position of the heave motion with the set-down motion is much lower than that without set-down motion. The results in this paper indicate that the set-down motion has a major impact on the safety of the platform inproduction operation, and it is also a threat to the strength of tension legs and risers. 相似文献
17.
The current study focuses on the response analysis of triangular tension leg platform (TLP) for different wave approach angles varying from 0° through 90° and its influence on the coupled dynamic response of triangular TLPs. Hydrodynamic loading is modeled using Stokes fifth-order nonlinear wave theory along with various other nonlinearities arising caused by change in tether tension and change in buoyancy caused by set down effect. Low frequency surge oscillations and high frequency tension oscillations of tethers are ignored in the analysis. Results show that wave approach angle influences the coupled dynamic response of triangular TLP in all degrees of freedom except heave. Response in roll and sway degrees of freedom are activated which otherwise are not present in TLP's response to unidirectional waves. Pitch and roll responses are highly stochastic in nature indicating high degree of randomness. Variation in surge, sway and heave responses are nonlinear and are not proportional to change in wave height for the same period. 相似文献
18.
参考英国的Kincardine风机采用的新式的Semi-Spar概念,结合spar式基础和半潜式基础的特点,提出了一种新式海上浮式风机平台模型,并基于三维势流理论,利用AQWA软件进行水动力计算,验证新式平台可靠性。分析了在风、浪、流荷载联合作用下,锚链竖向夹角、系缆数量对风机浮式平台运动性能和系泊张力的影响,对系泊系统进行优化,并验证极端工况下的可靠性。结果证明风机平台水平运动和纵摇运动幅值较小,但垂荡幅值略大,而通过减小锚链竖向夹角可以控制平台运动响应幅值,增加系缆数量可以同时减小系泊张力大小。计算结果证明了新型Semi-Spar式海上风机平台可行性,为浮式风机平台及系泊系统的设计提供参考。 相似文献
19.
基于3D FEMDEM方法建立三维原型尺度数值模型,模拟波浪荷载作用下斜坡上护面块体内部的应力分布。波浪作用下结构物的水动力荷载采用微幅波理论模拟,护面块体之间的运动、碰撞接触以及块体内部的应力变化采用3D FEMDEM方法模拟。块体之间的接触力采用基于势函数的罚函数法计算,有限元的变形采用中心差分的显式方法求解。应用该数值模型与ANSYS软件程序对自重作用下混凝土扭王字块的内部应力分布特性进行了比较分析,验证了数值模型应力计算的可行性和计算精度。通过数值模拟计算给出了波浪作用下斜坡上护面块体之间的相对运动和块体内部的应力分布及应力历时曲线,探讨了块体内部应力变化特性。 相似文献
20.
The element stiffness matrix of the equivalent beam or pipe element of the deformed leg of the platform is derived by the finite element method. The stresses and displacements of some damaged components are calculated, and the numeri-cal solutions agree well with those obtained by the fine mesh finite element method. Finally, as an application of this method, the stresses of some platform structures are calculated and analyzed. 相似文献