首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
赵丽娟 《海洋学报》2010,32(9):6219-6223
搭建了光纤布里渊频移测量系统,实现了色散位移光纤20 ℃到820 ℃布里渊频移的测量,并对测量数据进行拟合. 在环境温度大范围变化时,目前采用的布里渊频移-温度一阶线性关系式对测量数据分析误差较大,针对这个问题,本文从纯石英光纤的结构特点和材料的物性系数出发,在分析光纤的热膨胀系数、光纤密度、折射率、弹性模量和泊松比与宽范围温度关系的基础上,根据布里渊频移与各物性参数的关系式理论推导了宽范围温度变化与布里渊频移之间的二次项关系式. 理论推导结果与实验数据基本符合,验证了理论分析的正确性,从而为光纤宽范围布  相似文献   

2.
王晶  王项南 《海洋技术学报》2006,25(2):21-22,72
文章从理论上分析了布里渊散射光的频移和强度与海水温度和应力的关系,针对分布式布里渊散射光纤传感器测量海水温度和压力的测量原理进行了论述,对该测量系统的构成以及测量的实现进行了探讨。  相似文献   

3.
关致和 《海洋测绘》2002,22(5):45-45
海军海洋测绘研究所与无锡海鹰加科公司协作研制的HY12 0 0系列声速剖面仪 ,于 2 0 0 2年 8月通过海军装备部门组织的技术鉴定。声速剖面仪是一种测量声波在水中传播速度的精密水声仪器。它采用环鸣法直接测量声信号在固定距离内的传播时间得到声速 ,同时通过温度及压力传感器测量温度和垂直湿度。能快速、有效、方便地为测深仪等声纳设备校正测量误差 ,提供实时的声速剖面数据。该系列声速剖面仪有两个类型 :A型为电缆式 (水深 10 0m以内 ) ,可选计算机或掌上机作为水上终端 ;B型为自容式 (2 0 0m ,可扩展 ) ,内装不挥发存储器 ,可存…  相似文献   

4.
印尼海啸区附近海域沉积物声速测量及声学特性分析   总被引:3,自引:2,他引:1  
介绍了沉积物柱状样超声透射法测量方法和原理.对印尼海啸区附近海域沉积物柱状样进行了现场测量,通过测量数据的处理和分析,给出了沉积物的垂向声速剖面.讨论了声速与频率的关系,指出声速具有随频率的0.1次方增大的频散特性.分析沉积深度、结构以及生物扰动等方面的因素对声学测量结果的影响,结果表明海底地震引起的沉积物变迁、沉积物结构扰动、气体的混入等对声速的测量结果均产生影响.  相似文献   

5.
开展多波束水深测量应同步进行声速剖面探测。因海上作业条件恶劣、作业时间受限及设备性能局限等影响,在深远海海域常获取不到全深度的实测声速剖面。尽管利用温盐场模型可将声速剖面直接延拓至实地水深的最大深度,但这种气候态平均声速剖面与实际的声速剖面间存在不可控的系统性偏差,会给声速改正及水深测量成果带来质量隐患。给出了一种提高深远海全深度声速剖面重构精度的方法,即利用有效探测深度附近的实测温度盐度值,对大于有效探测深度的各水层的模型温度盐度值施加程度不一的约束控制。结果表明,经优化后全深度声速剖面的重构精度得到明显提高,其中2个XCTD站点声速剖面的互差SSPD分别由-2.5~1.0 m/s优化为0.0~1.0 m/s、0.0~2.6 m/s优化为-1.5~0.0 m/s; 2个CTD站点声速剖面的互差SSPD分别由-0.5~1.7 m/s优化为-0.4~0.3 m/s、-2.15~0.8 m/s优化为-1.4~0.8 m/s。  相似文献   

6.
提出最大差、中误差和全程平均差作为声速剖面曲线比较的精度指标。使用CNSVPGets软件对218条实测声速剖面曲线与软件获取剖面曲线进行对比计算,统计了比对曲线的最大水深、最大差、中误差、全程平均差;全部对比曲线的平均水深为1231.36m,平均最大差为6.74m/s,平均中误差为2.68m/s,全程平均差为1.72m/s。全程平均差小于5m/s的对比剖面对占95.4%,由此推论软件获取声速剖面的全程平均差极限误差为5m/s,中误差为2.5m/s;用软件获取声速剖面取代实测剖面用于水深测量计算,对测深精度的影响比海道测量规定的深度测量极限误差低1个数量级,因此可以使用软件获取声速剖面用于海道测量的深度测量声速改正。基于软件获取声速剖面的效率和重要性提出了建立和维护中国的全球声速剖面模型的建议。  相似文献   

7.
对夏威夷檀香山岛的两个站(H3和H4)钙质沉积物进行了20~100kHz的原位纵波声速和声衰减测量.它们均有轻微的频散.随频率的增加H3站位声速从1691m/s增加到1708m/s,H4站位的声速从1579m/s增加到1585m/s.随频率的增加H3站位的有效衰减从15dB/m增加到75dB/m,H4站位的有效衰减从22dB/m增加到62dB/m.运用Biot-Stoll模型对所测得的纵波速度和声衰减数据进行了Biot模型未知参数反演,发现粒径较大的H3站的沉积物(孔隙率为45%)比粒径较小的H4站的沉积物(孔隙率为56%)具有曲率小和渗透率及孔隙半径都大的性质.  相似文献   

8.
海缆作为连接海上风电场和陆上集中控制中心的“纽带”,承担着整个风电场的电力传输和通信任务。本文以实时监测海缆运行状态、提高海缆故障诊断效果为目标,构建计及复杂海洋环境适应性的海缆敷设故障特征提取模型。本文基于复杂海洋环境对海缆敷设的影响,分析布里渊频移与电缆温度、应变的关系,构建三者之间的线性方程;结合拉曼散射信号的温...  相似文献   

9.
为了研究西太平洋声散射层的垂向分布特征和日变化规律,分析了多波束测深系统的水体影像数据。观测结果表明,西太平洋存在着两个声散射层,一个声散射层位于0~200 m,另一个声散射层位于500~700 m,两个声散射层散射强度具有明显的日变化特征,上层散射层的散射强度呈现白天弱,夜晚强的特征,而下层散射层的散射强度日变化规律与上层相反,并且发现深散射层的厚度也存在日变化特征;分析了此种方法的优缺点,对以后声散射层的观测分析提供了新的思路。此外,利用同时下放的声速仪(SVP)的温度和深度数据对下放式声学多普勒流速剖面仪(LADCP)的观测结果进行了修正,得到了更为精确的声散射层垂向位置分布。  相似文献   

10.
根据2014年在南中国海开展声学试验的定深爆炸宽带声信号数据进行海底地声参数反演.考虑到不同海底声参数对不同声场物理参数的敏感程度不同以及不同海底声参数对不同反演方法的敏感程度亦不同,综合应用2种反演方法得到不同底质声参数:(1)根据接收的直达波和海底反射波计算得到关注海域的海底反射系数进而反演得到海底声阻抗;(2)实验海区的海底地形为大陆坡,选取Hamilton总结的关于沉积物声速与沉积物密度关系的经验公式,结合沉积物声阻抗与沉积物声速、沉积物密度的关系,进而反演得到沉积物声速和沉积物密度.沉积物声学参数的取样测量是在实验室条件下进行的,温度为23℃,大气压1×105Pa,由于沉积物孔隙海水是决定沉积物声速的关键且受温度压强变化的影响显著,本研究利用沉积物声速与孔隙海水声速的比值即使在温度压强变化的情况下较稳定的特点,可对沉积物声速在实验室条件和海底原位条件进行校正.校正到海底温度和压强后,反演结果与沉积物取样的实测结果和Hamilton总结的结果吻合得相当好:(1)声阻抗的反演结果为2.065 6×10~5g/(cm2·s),修正后的沉积物取样结果则为2.046 0×10~5g/(cm~2·s),Hamilton总结的结果为2.238 0×10~5g/(cm~2·s);(2)声速的反演结果为1 482.6m/s,修正后的沉积物取样结果为1 467.5 m/s,Hamilton总结的结果为1 502.8 m/s;(3)密度的反演结果为1.393 2 g/cm3,沉积物取样结果为1.400 0 g/cm~3,Hamilton总结的结果为1.489 0 g/cm3.  相似文献   

11.
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.  相似文献   

12.
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.  相似文献   

13.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.  相似文献   

14.
15.
《海洋学报(英文版)》2014,(9):F0003-F0003
<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,  相似文献   

16.
The relationship between the flux of exotic benthic foraminiferal tests (i.e. tests which are supplied from open-sea sources alone) in a tidal inlet and that of bulk sediment was analysed, which can be expressed as two first-order linear equations. According to this relationship, in order to determine net sediment transport directions in the entrance, the test concentration in surficial sediments of the tidal basin can be compared against a ‘ critical level ’. The critical level is determined for the conditions that no net transport of bulk sediment is present within the entrance. If the observed concentration (averaged over the tidal basin) is higher than the simulated critical level, then the net sediment transport is directed to landward. This method is applied to the analysis of net sand transport at Christchurch Harbour, a tidal inlet system located in southern England. In this investigation, concentrations of exotic foraminiferal tests in the surficial sediments of the tidal basin and ebb tidal delta area were obtained from the analysis of sea-bed sediment samples. A series of probable critical levels were calculated based upon the data sets with regard to: (1) sediment discharge from the rivers; (2) magnitude of sediment discharge within the entrance during the ebb; (3) the test concentration outside the harbour; (4) the thickness of the moving layer; and (5) two parameters associated with dispersive processes. The results show that the concentration in the tidal basin sediment is higher than a number of simulated critical concentrations for representative cases. Consequently, the high level of the concentration of exotic benthic foraminiferal tests within the harbour should be explained as a result of landward net transport of sands within the entrance.  相似文献   

17.
Coastal inundation associated with extreme sea levels is the main factor which leads to the loss of life and property whenever a severe tropical cyclonic storm hits the Indian coasts. The Andhra and Orissa coasts are most vulnerable for coastal inundation due to extreme rise in sea levels associated with tropical cyclones. Loss of life may be minimized if extreme sea levels and associated coastal flooding is predicted well in advance. Keeping this in view, location specific coastal inundation models are developed and applied for the Andhra and Orissa coasts of India. Several numerical experiments are carried out using the data of past severe cyclones that struck these regions. The simulated inland inundation distances are found to be in general agreement with the reported flooding.  相似文献   

18.
19.
Grain size and water content in box-core sediments from the Clarion-Clipperton fracture zone (C-C zone) in the northeast equatorial Pacific were analyzed in detail to understand the downcore variations across a hiatus between Quaternary and Tertiary layers. Grain-size distributions in the topmost core sediments show two modes: a coarse mode (peaked at 50 μm) and a fine mode (at 2-25 μm). The coarse mode disappears gradually with depth accompanied by the dissolution of siliceous fossil tests, whereas the fine mode coarsens due to the formation of authigenic minerals. Water content increases abruptly across a color boundary between an upper pale brown layer and a lower dark brown layer that is the hiatus between Quaternary and Tertiary layers. Abundant smectites and microvoid molds, which are created by the prolonged fossil dissolution in the underlying sediment, are attributed for the abrupt downcore variation of water content. Overall variations in grain size and water content in the topmost core sediments in the western C-C zone are possibly constrained by the dissolution of biogenic siliceous fossils. Variations in geotechnical properties related to these changes must be considered in the design of nodule collectors.  相似文献   

20.
This article concerns an interrelation between the sea levels and the western boundary flow near a tectonic boundary in a local zone in the Northwestern Pacific. In this zone, sea level variations at stations located on the coast facing the Pacific are studied to find the interrelation between variations of the Kurosio flow as an index of the distance of the flow axis off a specific coast. The result is discussed after data processing of the monthly means of the sea levels, and a notice is taken of variations caused by active crustal upheavals during a seismic event, a local earthquake.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号