共查询到20条相似文献，搜索用时 265 毫秒
1.
Recently derived (Webster et al., 2011), simplified higher-level Green–Naghdi equations (GN-3, GN-5 and GN-7) are used in this work to simulate the transformation of two-dimensional, shallow-water wave problems. The spatial derivatives are discretized through a five-point difference scheme. A new algorithm is developed to solve the resulting block-pentadiagonal matrix. These high-level GN equations are then utilized to develop a numerical wave tank. A wave-maker is placed at the forcing boundary of the tank that uses the stream-function theory to generate nonlinear incident waves. The numerical wave tank is used to analyze the effects of large-amplitude waves passing over a submerged bar. A damping zone is placed near the wave-maker (up-wave side) to absorb the reflected waves from the front side of the submerged bar. Another damping zone is placed at the down-wave side of the computational domain to absorb the radiated waves. In the first test case, the front and back slopes of the bar are both mild (Luth et al., 1994). The waves that evolved over the bar are simulated by using the GN-3, GN-5 and GN-7 equations. The GN-3 equations provide time histories that compare well with the experimental data at different wave gauges, except at the ones behind the bar. The results of the GN-5 and GN-7 equations compare very well with all the experimental data considered here. In the second test case, the front and back slopes of the bar are both steep (Ohyama et al., 1995). The GN-5 equations predict the wave elevation well. In the third test case, the front and back slopes of the bar alternate, one of them being mild and the other one being steep (Zou et al., 2010). Again, the predictions of the GN-5 equations agree with the experimental data well. In all the test cases considered in this work, there are some differences between the GN-3 and GN-5 results after the crest of the bar. Numerical results obtained by the GN-5 and GN-7 equations are almost the same along the wave flume, but the GN-7 equations require more computational time. Therefore, the GN-5 results are accepted here as the converged GN theory results. The numerical validations show that the GN-5 equations can simulate the strongly nonlinear and dispersive waves observed behind the submerged bar crest satisfactorily. 相似文献
2.
1 .IntroductionApile supportedplatesubmergedatacertaindepthunderseasurfacewasdevelopedasanewtypeofunderwaterbreakwaterfortheprotectionofcoastlinesandharbors .Thisisbecauseitdoesnothinderthewaterexchangebetweentheopenseaandtheprotectedareanordoesithindertheviewovertheopensea .Besides,itislessdependentonthegeotechnicalconditionsoftheseabottomwherethestructureistobeinstalled ;however,itscostishigh ,particularlyinrelativelydeepwaters .Formanyapplicationsitispossibletoreducethewavemotionintheprotec… 相似文献
3.
In actual sea states, damage to offshore floating structures is usually caused by a few extreme waves or wave groups in an irregular wave train. Accurate simulation of the irregular wave trains can lay a solid foundation for understanding the local flow field and impact loads that would potentially cause such damage. This paper describes how the generation of a single extreme wave was investigated. Determination of the wave-maker motion for generating specified irregular wave trains is the key to this work. First, an experimental irregular wave train was decomposed into a certain number of small-amplitude waves. Fourier series expansion was performed to determine the amplitude and the initial phase angle of each wave component. Then a hydrodynamic transfer function was used to calculate the amplitude of the wave-maker motion associated with each wave component. Superposition was made on all the wave components to get the final wave-maker motion. During the numerical simulation, calculated horizontal velocity profiles of the extreme wave at different moments were analyzed and compared with experimental results, and a satisfactory agreement was obtained. In the simulation, VOF method was employed to capture the free surface, and a dissipation zone was used to deal with wave reflection. 相似文献
4.
The unsteady, two-dimensional Navier–Stokes equations and the exact free surface boundary conditions were solved to study the interaction of a solitary wave and a submerged dike. A piston-type wavemaker was set up in the computational domain to produce the incident solitary waves. The incident wave and the associated boundary layer flow in a wave tank with a flat bed were compared with the analytical solutions to verify the accuracy of this numerical scheme. Effects of the incident wave height and the size of the dike on the wave transformation, the flow fields, and the drag forces on the dike were discussed. Our numerical results showed that even though the induced local shear stress on the top surface of the dike is large at some particular locations, the resultant pressure drag is much larger than the friction drag. The primary vortex generated at the lee side of the dike and the secondary vortex at the right toe of the dike may scour the bottom and cause a severe problem for the dike. 相似文献
5.
The performance of coastal vertical seawalls in extreme weather events is studied numerically, aiming to provide guidance in designing and reassessing coastal structures with vertical wall. The extreme wave run-up and the pressure on the vertical seawall are investigated extensively. A time-domain higher-order boundary element method (HOBEM) is coupled with a mixed Eulerian-Lagrangian technique as a time marching technique. Focused wave groups are generated by a piston wave-maker in the numerical wave tank using a wave focusing technique for accurately reproducing extreme sea states. An acceleration-potential scheme is used to calculate the transient wave loads. Comparisons with experimental data show that the extended numerical model is able to accurately predict extreme wave run-ups and pressures on a vertical seawall. The effects of the wave spectrum bandwidth, the wall position and the wave nonlinearity on the wave run-up and the maximum wave load on the vertical seawall are investigated by doing parametric studies. 相似文献
6.
In this work the analysis of sloshing of water in rectangular open tanks has been extensively carried out. Two mathematical models are employed, respectively the Reynolds Averaged Navier Stokes Equations (RANSE) and the Shallow Water Equations (SWE). The RANSE are solved using a modified form of the well established MAC method (SIMAC) able to treat both the free surface motion and the viscous stresses over the rigid walls accurately. The Shallow Water Equations are solved by means of a simple and powerful algorithm (CE-SE) able to deal with large impacting waves over the tank walls.Successively, in order to validate the mentioned algorithms and for a better understanding of the sloshing phenomenon, experimental tests have been carried out using a 0.5 m breadth rectangular tank in periodic roll motion.It has been shown that RANSE provide more accurate solutions than SWE for small or moderate amplitudes of excitation. In particular in this paper it is proved that the shallow water approximation can be efficiently adopted within liquid depth to tank breadth RATIO = 0.15, when examining the sloshing problem. By increasing the water level inside the tank, results by SWE show large qualitative and quantitative disagreement with experiments. Nevertheless, in the case of large amplitude excitation, when sprays and large breaking waves are expected, SWE provide a fairly good estimate of the sloshing induced waves.Finally a simple baffle configuration inside the tank has been considered. By the analysis of numerical results, it has been observed that the presence of a vertical baffle at the middle of the tank dramatically changes the sloshing response compared to the unbaffled configuration. It produces a jump-like effect, resulting in a weak magnification of the dynamic loads on the vertical walls out of resonance, and a strong reduction of the dynamic loads in the resonance condition. 相似文献
7.
I~IOWNUmerics wave tank is a ~ tOOl by which variouS nonlinear wave - ac interactionpwhleln can be treated in time domain. As the face stage, we f~ our efforts on the devious of an effita saution tee~ of fully nofor waves. aam numtried of water - wavesconnected PwhlemS, es~ in a wave tank, is alwayS comas Of PartS: wave generation, P~ and a~. The effi~ Of a nUm~ wave tankdepends not Only on the qwhty Of the wave abotion tecboaue, which allowS the lOng times~ and keePS finite tank leng… 相似文献
8.
《Coastal Engineering》2006,53(5-6):395-417
This paper is the second part of the work presented by Garcia et al. [Garcia, N., Lara, J.L., Losada, I.J., 2004. 2-D numerical analysis of near-field flow at low-crested breakwaters. Coastal Engineering 51 (10), 991–1020]. In the mentioned paper, flow conditions at low-crested rubble-mound breakwaters under regular wave attack were examined, using a combination of measured data of free surface, bottom pressure and fluid velocities from small-scale experiments and numerical results provided by a VOF-type model (COBRAS) based on the Reynolds-Averaged Navier–Stokes (RANS) equations. This paper demonstrates the capability of the COBRAS model to reproduce irregular wave interaction with submerged permeable breakwaters. Data provided by the numerical model are compared to experimental data of laboratory tests, and the main processes of wave–structure interaction are examined using both experimental and numerical results. The numerical model validation is carried out in two steps. First, the procedure of irregular wave generation is verified to work properly, comparing experimental and numerical data of different cases of irregular wave trains propagating over a flat bottom. Next, the validation of the numerical model for wave interaction with submerged rubble-mound breakwaters is performed through the simulation of small-scale laboratory tests on different incident wave spectra. Results show that the numerical model adequately reproduces the main aspects of the interaction of random waves with submerged porous breakwaters, especially the spectral energy decay at the structure and the spectrum broadening past the structure. The simulations give good results in terms of height envelopes, mean level, spectral shape, root-mean-square height for both free surface displacement and dynamic pressure inside the breakwater. Moreover, large-scale simulations have been conducted, on both regular and irregular incident wave conditions. The overall pattern of the wave interaction with a large-scale submerged breakwater is adequately reproduced by the numerical model. The processes of wave reflection, shoaling and breaking are correctly captured. The good results achieved at a near prototype scale are promising regarding the use of the numerical model for design purposes. 相似文献
9.
The substructures of offshore wind turbines are subjected to extreme breaking irregular wave forces. The present study is focused on investigating breaking irregular wave forces on a monopile using a computational fluid dynamics (CFD) based numerical model. The breaking irregular wave forces on a monopile mounted on a slope are investigated with a numerical wave tank. The experimental and numerical irregular free surface elevations are compared in the frequency-domain for the different locations in the vicinity of the cylinder. A numerical analysis is performed for different wave steepness cases to understand the influence of wave steepness on the breaking irregular wave loads. The wave height transformation and energy level evolution during the wave shoaling and wave breaking processes is investigated. The higher-frequency components generated during the wave breaking process are observed to play a significant role in initiating the secondary force peaks. The free surface elevation skewness and spectral bandwidth during the wave transformation process are analysed and an investigation is performed to establish a correlation of these parameters with the breaking irregular wave forces. The role of the horizontal wave-induced water particle velocity at the free surface and free surface pressure in determining the breaking wave loads is highlighted. The higher-frequency components in the velocity and pressure spectrum are observed to be significant in influencing the secondary peaks in the breaking wave force spectrum. 相似文献
10.
With growing computational power, the first-order wave-maker theory has become well established and is widely used for numerical wave flumes. However, existing numerical models based on the first-order wave-maker theory lose accuracy as nonlinear effects become prominent. Because spurious harmonic waves and primary waves have different propagation velocities, waves simulated by using the first-order wave-maker theory have an unstable wave profile. In this paper, a numerical wave flume with a piston-type wave-maker based on the second-order wave-maker theory has been established. Dynamic mesh technique was developed. The boundary treatment for irregular wave simulation was specially dealt with. Comparisons of the free-surface elevations using the first-order and second-order wave-maker theory prove that second-order wave-maker theory can generate stable wave profiles in both the spatial and time domains. Harmonic analysis and spectral analysis were used to prove the superiority of the second-order wave-maker theory from other two aspects. To simulate irregular waves, the numerical flume was improved to solve the problem of the water depth variation due to low-frequency motion of the wave board. In summary, the new numerical flume using the second-order wave-maker theory can guarantee the accuracy of waves by adding an extra motion of the wave board. The boundary treatment method can provide a reference for the improvement of nonlinear numerical flume. 相似文献
11.
Wave-induced loads on a submerged plate, representative of submerged breakwater, coastal-bridge deck and a certain type of wave energy converter, in a uniform current are investigated in this study using fully nonlinear numerical wave tanks (NWTs) based on potential flow theory. The coupling effect of wave and current is explored, and the underlying interaction mechanisms of the hydrodynamic forces are described. The presence of a background current modifies the frequency dispersion. It produces changes of the water-surface elevation, and also has an effect on wave-induced loads. Depending on the nonlinearity, higher harmonic wave components are generated above the submerged plate. These contribute to the wave forces. It is found that the horizontal and the vertical force, hence the moment, are affected in the opposite way by the currents. The Doppler shifted effect dominates the vertical force and the moment on the plate. Whereas, the Doppler shifted effect and the generation of higher wave harmonics play opposite roles on the horizontal forces. The contribution of 2nd order harmonics is found to be up to 30% of the linear component. The current-induced drag force, represented by the advection term ρU∂φ/∂x in the pressure equation, is found to lead to a decrease in the moment for the most range of wavelengths considered, and an increase in the moment for a small range of longer waves. 相似文献
12.
In this paper, a numerical model is established for estimating the wave forces on a submerged horizontal circular cylinder. For predicting the wave motion, a set of two-dimensional Navier-Stokes equations is solved numerically with a finite element method. In order to track the moving non-linear wave surface boundary, the Navier-Stokes equations are discretized in a moving mesh system. After each computational time step, the mesh is modified according to the changed wave surface boundary. In order to stabilize the numerical procedure, a three-step finite element method is applied in the time integration. The water sloshing in a tank and wave propagation over a submerged bar are simulated for the first time to validate the present model. The computational results agree well with the analytical solution and the experimental data.Finally, the model is applied to the simulation of interaction between waves and a submerged horizontal circular cylinder.The effects of the KC number and the cylinder depth on the wave forces are studied. 相似文献
13.
The nonlinear diffraction of 2D single and twin hulls are studied by employing a mixed Eulerian–Lagrangian model based on a higher-order cubic-spline boundary element solver. Two types of simulations are considered. In the first, waves are generated by a piston-type wave-maker in a rectangular tank and in the second case a nonlinear incident wave is assumed to exist in the tank in which the body is introduced. For the application of this model, the full nonlinear diffraction problem is recast in terms of a perturbation wave-field. Computations are performed for rectangular and triangular hull geometries. Computed results show significant nonlinearities, particularly in the heave force. The twin hull results show the influence of wave interference on the diffraction forces. This interference influences the surge force considerably, but heave force is less affected. 相似文献
14.
Impact Analysis of Air Gap Motion with Respect to Parameters of Mooring System for Floating Platform
In this paper, the impact analysis of air gap concerning the parameters of mooring system for the semi-submersible platform is conducted. It is challenging to simulate the wave, current and wind loads of a platform based on a model test simultaneously. Furthermore, the dynamic equivalence between the truncated and full-depth mooring system is still a tuff work. However, the wind and current loads can be tested accurately in wind tunnel model. Furthermore, the wave can be simulated accurately in wave tank test. The full-scale mooring system and the all environment loads can be simulated accurately by using the numerical model based on the model tests simultaneously. In this paper, the air gap response of a floating platform is calculated based on the results of tunnel test and wave tank. Meanwhile, full-scale mooring system, the wind, wave and current load can be considered simultaneously. In addition, a numerical model of the platform is tuned and validated by ANSYS AQWA according to the model test results. With the support of the tuned numerical model, seventeen simulation cases about the presented platform are considered to study the wave, wind, and current loads simultaneously. Then, the impact analysis studies of air gap motion regarding the length, elasticity, and type of the mooring line are performed in the time domain under the beam wave, head wave, and oblique wave conditions. 相似文献
15.
Numerical simulations using momentum source wave-maker applied to RANS equation model 总被引：2，自引：0，他引：2
For Navier-Stokes equation model using the VOF scheme, Lin and Liu (Lin, P. and Liu, P.L.-F. (1999). Internal wave-maker for Navier-Stokes equations models. J. Waterw. Port Coast. Ocean Eng., 125 (4), 207–215.) developed an internal wave-maker method for which a mass source function of the continuity equation was used to generate target wave trains. Using this internal wave-maker method, various numerical experiments have been conducted without any problems due to waves reflected by a wave-maker. In this study, an internal wave-maker method using a momentum source function was proposed. Various numerical simulations in two and three dimensions were performed using the momentum source wave-maker applied to the RANS equation model in a CFD code, FLUENT. To verify their applicability in 2 dimensions, the computational results obtained using the momentum source wave-maker in a channel of constant depth were compared with the results obtained by using the mass source wave-maker and with the analytical solutions. And the results of the present numerical simulations of hydraulic experiments, which represent nonlinear waves on a submerged shoal and breaking waves on a plane beach, were compared with measurements. The comparisons showed good agreements between them. To see their applicability into 3-dimensional cases, the present results in a basin of constant depth were compared with the analytical solutions, and they agreed well with each other. In addition, vertical variation of longshore current was presented by using the 3-dimensional simulation results. 相似文献
16.
《Coastal Engineering》1999,37(2):123-148
The Navier–Stokes equations and the exact free surface boundary conditions are solved to simulate wave deformation and vortex generation in water waves propagating over a submerged dike. Incident waves are generated by a piston-type wavemaker set up in the computational domain. Numerical results are compared with experimental data in order to confirm the validity of the numerical model. The fast Fourier transform and a wave resolution technique are applied to decompose the transformed waves and the higher harmonics. Effects of different parameters on wave transformation and vortex generation are studied systematically. These parameters include the Ursell number, the Keulegan–Carpenter number, the water depth ratio, the Reynolds number, the length aspect ratio of the dike, and the type of dike. 相似文献
17.
Numerical Wave Channel with Absorbing Wave-Maker 总被引：2，自引：0，他引：2
Wang Yongxue
Professor State Key Laboratory of Coastal Offshore Engineering Dalian University of Technology Dalian 《中国海洋工程》1995,(2)
The numerical wave channel has been developed based on the volume of fluid method (VOF) in conjunction with the Navier-Stokes equations. The absorbing wave-maker boundary on the left side of the channel is presented by prescribing velocity reference to linear wave-maker theory. The principle of which is that the numerical wave-maker is designed to move in a way that generates the required incident wave and cancels out any reflected wave that reach it at the same time. On the right side of the channel, the open boundary is set to permit incident waves to be transmitted freely. The parametric studies have been carried out at a range of ratios of water depth to wave length d/ L from 0.124 to 0.219, with wave height in the front of paddle/water depth ratio (H0 / d) from 0.1 to 0.3. Wave height, wave pressure distribution along the channel and velocity field are obtained for both open boundary condition and reflective boundary condition at the other end of the channel. For a reflective case, it is shown that 相似文献
18.
The authors have previously determined that the effectiveness and failure pattern of the ice cover caused by flexural-gravity waves generated by a submerged body motion near the bottom ice can greatly depend on the depth of the water area. In its turn, the presence of a ledge on the ice surface may affect a wave propagation pattern. This paper presents an experimental study of the bottom contour influence on the deflection and length of flexural-gravity waves. The authors describe a numerical model for the analysis of the deformed state of ice caused by hydrodynamic loads due to a submarine motion, taking into account the bottom contour. The experiments are carried out in the ice tank. The results of calculations and experiments are compared. 相似文献
19.
Numerical simulations are carried out for wave action on a submerged horizontal circular cylinder by means of a viscous fluid model, and it is focused on the examination of the discrepancies between the viscous fluid results and the potential flow solutions. It is found that the lift force resulted from rotational flow on the circular cylinder is always in anti-phase with the inertia force and induces the discrepancies between the results. The influence factors on the magnitude of the lift force, especially the correlation between the stagnation-point position and the wave amplitude, and the effect of the vortex shedding are investigated by further examination on the flow fields around the cylinder. The viscous numerical calculations at different wave frequencies showed that the wave frequency has also significant influence on the wave forces. Under higher frequency and larger amplitude wave action, vortex shedding from the circular cylinder will appear and influence the wave forces on the cylinder substantially. 相似文献
20.
基于开源程序REEF3D,通过建立高精度二维数值波浪水槽,系统研究了聚焦波浪在浅堤上传播变形的规律,着重分析了聚焦波浪通过浅堤的水动力过程及能量变化规律,讨论了不同波浪要素对聚焦波浪传播特性的影响。除此之外,还考虑了双浅堤布置对聚焦波浪传播变形的影响。研究结果表明:极端波浪通过浅堤时,堤顶水深越小,波浪主频能量衰减越显著。在给定堤顶水深条件下,聚焦点与浅堤的相对位置对聚焦波浪能量的衰减影响较小。在双浅堤布置条件下,随着浅堤间距的增加,上下游浅堤的相互影响逐渐减弱,高频段的波浪能量也随之减小。 相似文献