共查询到20条相似文献，搜索用时 31 毫秒
1.
Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study using the finite-difference code Fast Lagrangian Analysis of Continua (FLAC), to evaluate the bearing capacity for two interfering strip footings, subjected to centered vertical loads with smooth and rough interfaces. The soil is modeled by an elasto-plastic model with a Mohr–Coulomb yield criterion and associative flow rule. The interference effect is estimated by efficiency factors, defined as the ratio of the bearing capacity for a single footing in the presence of the other footing to that of the single isolated footing. The efficiency factors have been computed individually to estimate the effects of cohesion, surcharge, and soil weight using Terzaghi’s equation, both in a frictional soil with surcharge pressures and in a cohesive-frictional soil with surcharge pressures. The results have been compared with those available in the literature. 相似文献
2.
3.
通过模型试验研究了竖向荷载作用下砂土中斜桩的荷载传递性状,分析了桩身倾角及长径比对斜桩桩身轴力、弯矩、剪力、桩侧摩阻力及端阻比的影响。试验结果表明：在桩顶竖向荷载作用下,斜桩桩身轴力均小于相应直桩桩身轴力,桩身倾角越大,轴力沿深度衰减得越快,桩长径比越大,轴力沿深度衰减得也越快;斜桩桩身最大弯矩随桩身倾角及长径比的增加而增加,最大弯矩出现的深度与桩身倾角无关,只与长径比相关;不论桩身倾角及长径比的大小,斜桩桩身最大剪力均出现在桩顶截面处,桩身最大剪力随着桩身倾角的增加而增大;桩身倾角越大,斜桩最大摩阻力越大,长径比越大,斜桩最大摩阻力越小,斜桩最大摩阻力出现在桩顶下1/4～1/5桩长处;斜桩端阻比随着桩顶竖向荷载的增加而增大,随着桩身倾角及长径比的增加而减小。 相似文献
4.
《Geomechanics and Geoengineering》2013,8(2):107-111
The stability of eccentrically loaded strip footings on slopes was investigated using the method of finite element analysis based on the theory of elasto-plasticity. The analysis was done for two different soils involving three levels of slope angle, six footing locations, and two levels of load eccentricity plus central vertical loading. The strip footing analysed was a 3-ft (0.9 m) wide reinforced concrete footing embedded to a depth of 3 ft (0.9 m). The analysis focused on footing settlement, plastic yielding of soil, and ultimate bearing capacity. The results of analysis show that the influence of load eccentricity on footing pressure vs. footing centre settlement is negligibly small. However, the progressive soil yielding and ultimate bearing capacity are greatly affected by load eccentricity. Furthermore, the effect of load eccentricity differs considerably with the load location relative to the footing centre and slope crest. The ultimate bearing capacity for the eccentric load located on the slope side is significantly greater than that for the load located on the other side of the footing centre. For a 2(H): 1(V) slope in silty clay, the effect of slope on footing stability decreases with increasing footing location from slope crest as would be expected, and diminishes when the footing is located from the crest at about 5-times the footing width. 相似文献
5.
Ahmed M. Fahmy John R. de Bruyn T. A. Newson 《Geotechnical and Geological Engineering》2013,31(5):1525-1542
Two-dimensional plane strain finite element analysis has been used to simulate the inclined pullout behavior of strip anchors embedded in cohesive soil. Previous studies by other researchers were mainly concerned with plate anchors subjected to loads perpendicular to their longest axis and applied through the centre of mass. This paper investigates the behavior of vertical anchors subjected to pullout forces applied at various inclinations with respect to the longest anchor axis, and applied at the anchor top and through the centre of mass. The effects on the pullout behavior of embedment depth, overburden pressure, soil–anchor interface strength, anchor thickness, rate of clay strength increase, anchor inclination, load inclination and soil disturbance due to anchor installation were all studied. Anchor capacity is shown to increase with load inclination angle for anchors loaded through the centre of mass; greater effects are found for higher embedments. The results also show that anchor capacity improves at a decreasing rate with higher rates of increase of soil shear strength with depth. In addition, the capacity of vertically loaded anchors is shown to approximately double when the soil–anchor interface condition changes from fully separated to fully bonded. Similarly, disturbed clay strengths adjacent to the anchor following installation cause a significant reduction in anchor capacity. The results showed a significant effect of the point of load application for anchors inclined and normally loaded. The effects of other parameters, such as anchor thickness, were found to be less significant. 相似文献
6.
S. Benmebarek S. Benmoussa L. Belounar N. Benmebarek 《Geotechnical and Geological Engineering》2012,30(4):907-923
Natural soils are often deposited in layers. The estimation of the bearing capacity of the soil, using conventional bearing capacity theory based on the properties of the top layer, introduces significant inaccuracies if the thickness of the top layer is comparable to the width of the rigid footing placed on the soil surface. Saturated normally consolidated and lightly overconsolidated clays indicate that under undrained condition the cohesion of soil mass increases almost linearly with depth. A few theoretical studies have been proposed in the literature to incorporate the variation of cohesion with depth in the computation of the ultimate bearing capacity of strip and circular footings. In this paper, after reviewing previous works, numerical computations using the FLAC code (Fast Lagrangian Analyses of Continua) are reported to evaluate the two layered clays effect on the bearing capacity beneath rigid strip footing subject to axial static load. The results of the bearing capacity relating to the relative thickness of the top layer, the strength ratio of the soil two-layered clays and the rates of the increase of soil cohesion with depth are presented in Tables and graphs. The obtained results are compared with previous published results available in the literature. 相似文献
7.
基于传统的极限平衡条分法,利用临界滑动场法计算了条形基础的加筋地基极限承载力。假定土体处于极限平衡状态时,土体与筋材间存在均匀的摩擦力,通过建立土体条块极限平衡方程,推导了地基承载力的递推关系式。首先,设定计算土体范围,并划分条块和离散状态点;其次,根据递推公式计算各个状态点的参数,并搜索临界滑面;最后,根据搜索出的滑面计算地基承载力。通过实例比较进一步验证了计算结果的可靠性,并分析了首层筋带埋深、铺设层数和长度对地基承载力和滑面位置的影响。研究结果表明：地基承载力随着筋带埋深的增加先增大后减小;随着层数和长度的增加先逐渐增大,最后趋于稳定;滑面位置的变化规律主要是垂直影响深度和水平影响范围增大或减小。该方法原理简单、易于编程,为条形基础加筋地基承载力的计算提供了一种新思路,是临界滑动场法在地基承载力计算中的推广应用。 相似文献
8.
针对山区和丘陵等复杂地形下浅埋锚板抗拔承载力计算问题,基于极限分析上限定理、非线性Mohr-Coulomb强度准则及其关联流动法则,构造了斜坡浅埋水平条形锚板的曲线型破裂机制和机动许可速度场,采用变分极值原理获得了其上方土体破裂面方程和抗拔承载力的上限解,分析了斜坡倾角和锚板埋深对锚板抗拔承载力的影响。结果表明:随着斜坡倾角的增大,锚板抗拔承载力逐渐减小,此时其上方两侧土体破裂面不再对称且整体向下坡侧偏移;锚板抗拔承载力及其上方两侧土体破裂面宽度均随着埋深增大而增加;锚板埋深越小,斜坡倾角对其抗拔承载力的影响越大,应在计算中予以考虑,以更合理地反映斜坡浅埋水平条形锚板的抗拔承载特性。 相似文献
9.
Rabi Narayan Behera Chittaranjan Patra 《Geotechnical and Geological Engineering》2018,36(5):3029-3080
Extensive laboratory model tests have been carried out on a strip footing resting over dry sand bed subjected to eccentrically inclined load to determine the ultimate bearing capacity (Patra et al. in Int J Geotech Eng 6(3):343–352, 2012a. https://doi.org/10.3328/IJGE.2012.06.03.343-352, Int J Geotech Eng 6(4):507–514, b. https://doi.org/10.3328/IJGE.2012.06.04.507-514). Similarly, lower bound calculations based on finite element method were performed to compute the bearing capacity of a strip footing subjected to an eccentric and inclined load lying over a cohesionless soil with varying embedment depth and relative density (Krabbenhoft et al. in Int J Geomech ASCE, 2014. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000332). The load may be applied in two ways namely, towards the center line and away from the center line of the footing. Based on the results (both experimental and numerical analyses), a neural network model is developed to predict the reduction factor that will be used in computing the ultimate bearing capacity of an eccentrically inclined loaded strip footing. This reduction factor (RF) is the ratio of the ultimate bearing capacity of the footing subjected to an eccentrically inclined load to the ultimate bearing capacity of the footing subjected to a centric vertical load. A thorough sensitivity analysis is carried out to evaluate the parameters affecting the reduction factor. Based on the weights of the developed neural network model, a neural interpretation diagram is developed to find out whether the input parameters have direct or inverse effect on the output. A prediction model equation is framed with the trained weights of the neural network as the model parameters. The predictions from ANN, and those from other approaches, are compared with the results computed from both experimentation and FEM analyses. The ANN model results are found to be more accurate and well matched with other results. 相似文献
10.
In this paper, an effort is made to evaluate the seismic bearing capacity of shallow strip footing resting on c–ф soil. The formulation is developed to get a single coefficient of bearing capacity for simultaneous resistance of weight, surcharge and cohesion. Limit equilibrium method in Pseudo-static approach with Coulomb mechanism is applied here to evaluate the seismic bearing capacity. The seismic bearing capacity of footing (quE) is expressed in terms of single coefficient NγE. The effect of various parameters viz. angle of internal friction of soil (ф), angle of wall friction (δ), cohesion (c), ratio of depth to width of footing (df/B0), seismic acceleration (kh, kv) are studied on the variation of seismic bearing capacity co-efficients. 相似文献
11.
主要介绍了压桩力与单桩竖向极限承载力的关系,以及利用压桩力估算单桩竖向极限承载力的方法。在试桩阶段,位于饱和软土的摩擦桩,压桩力较低,桩的承载力主要来自土体恢复后桩侧的摩阻力。根据静载荷试验检测结果,用单桩竖向极限承载力除以压桩力,引出一个系数,称为压力比,通过分析比较,得出在昆明地区的正常压力比,静压预制管桩在1.3～2之间,静压预制方桩在2.5～5之间。用压桩力乘以压力比,可以估算单桩竖向极限承载力。还简要介绍了挤土效应和超孔隙水压力对桩的承载力的影响。在工程桩施工时,地层中的土体和孔隙水被挤压,形成孔隙水压力,会产生一个向上的浮力,导致已施工的桩上浮,单桩承载力显著降低。 相似文献
12.
Bearing Capacity of Strip Footings Near Slopes 总被引：2，自引：1，他引：1
In the last decades a great attention was given by many authors to the evaluation of the static and seismic bearing capacity
of footings near slopes. In this paper a model has been developed based on the limit equilibrium method, considering a circular
surface propagates towards the slope until the sloping ground is reached. The bearing capacity is investigated considering
either the distance of the footing from the edge of the slope and/or the effect of the footing embedment. A validation of
the proposed model was made by a comparison with solutions taken from literature regarding the evaluation of the bearing capacity
for a footing adjacent to a slope and for an inclined load. The loading conditions consist in vertical and horizontal stress
on the footing and on the soil below the footing. Both the inertial and kinematic effects of the seismic loading have been
analyzed, and a simple equation has been derived for the evaluation of the seismic bearing capacity. The static and seismic
bearing capacity has been investigated as a function of the soil friction angle, of the seismic coefficient, of the sloping
ground. Finally, the influence of the distance of the footing from the edge of the slope was taken into consideration in the
evaluation of the bearing capacity, and a threshold distance at which the reduction of the bearing capacity due to the sloping
ground vanishes has been defined. 相似文献
13.
非均质地基承载力及破坏模式的FLAC数值分析 总被引：3，自引：0，他引：3
利用基于Lagrangian显式差分的FLAC算法，通过数值计算，对黏结力随深度线性增长的非均质地基上条形基础和圆形基础的极限承载力及地基破坏模式进行了对比计算与系统分析。研究表明：（1）随着地基黏结力沿深度非均匀变化系数的增大，地基的破坏范围逐渐集中在地基表层和基础两侧：（2）即使地基的非均质程度较小，当将非均质地基近似地按均质地基考虑时，由此所估算的承载力可能过于保守；（3）地基承载力系数随黏结力沿深度非均匀变化系数的增大而非线性地增大。与数值解相比，skempton与Peck等近似公式均可能高估了非均质地基承载力。 相似文献
14.
Bearing capacity of two close strip footings on soft clay reinforced with geotextile 总被引：1，自引：1，他引：0
For many years ago, the beneficial effects of using reinforcement to improve the property of soil have been demonstrated. Over the last three decades, the use of polymeric reinforcement such as geotextile has increased in geotechnical engineering. Among the possible applications, earth reinforcement techniques have become useful and economical techniques to solve many problems in geotechnical engineering practice, such as improve the bearing capacity and settlement characteristics of the footing. This research presents the effect of geotextile inclusion on the bearing capacity of two close strip footings located at the surface of soft clay. A broad series of finite element analysis were performed on two footings with width of 1 and 2 m using two-dimensional plane strain model using the computer code Plaxis (ver 8). Only one type of soft clay was used for the analysis, and the soil was represented by two yielding criteria including hardening soil model and Mohr–Coulomb model, while reinforcement was represented by elastic element, and at the interface between the reinforcements and soft clay, interface elements have been used. A wide range of boundary conditions, including unreinforced and reinforced cases, was analyzed by varying parameters such as number of geotextile layers, vertical spacing of layers, depth to topmost layer of geotextile, tensile stiffness of geotextile layers, and distance of between two footings. From numerical results, the bearing capacity ratio and the interference factor of the foundations have been estimated. On the basis of the analysis performed in this research, it can be concluded that there is a best distance between footings and optimum depth for topmost layer to achieve maximum bearing capacity for closely spaced strip footings. The bearing capacity was also found to increase with increasing number of reinforcement layers if the reinforcements were placed within a range of effective depths. In addition, the analysis indicated that increasing reinforcement stiffness beyond a threshold value does not result in a further increase in the bearing capacity. 相似文献
15.
《Geomechanics and Geoengineering》2013,8(4):271-277
The paper presents the performance of a square footing with a structural skirt resting on sand and subjected to a vertical load through an experimental study. A series of tests were conducted in a model test tank to evaluate the performance in terms of improvement in bearing capacity and reduction in settlement of a square footing with and without a structural skirt. The results of the study reveal that this type of reinforcement increases the bearing capacity, reduces the settlement and modifies the load settlement behaviour of the footing. The various factors influencing the bearing capacity improvements and settlement reduction using a structural skirt are identified. Skirt factors are proposed which can be introduced into the general ultimate bearing capacity equation for a square footing resting on sand. The predictions made through the modified equation are in reasonable agreement with the experimental results. The bearing capacity of square footing is increased in the range of 11.2 to 70%. The improvement in bearing capacity decreases with the increase in base roughness of the footing. Further, an equation for a settlement reduction factor is proposed which can be used to calculate the settlement of the square footing with structural skirt resting on sand. The settlement reduction factor (SRF, defined as the ratio of settlement of footing with structural skirt to the settlement of footing without structural skirt at a given load) was in the range 0.11 to 1.0 depending on applied load and skirt depth ratio with the use of a structural skirt. The results further reveal that for a given depth of the skirt, the settlement reduction factor decreases with the increase in applied load. The improvement in the bearing capacity and reduction in settlement of a square footing with a structural skirt resting on sand are dependent on the geometrical and structural properties of the skirt, footing, sand characteristics and interface conditions of the sand–skirt–footing system. 相似文献
16.
条形基础极限承载力数值分析 总被引：2，自引：0，他引：2
根据塑性力学滑移线理论,推导了条形地基在极限平衡状态下的平衡微分方程,然后利用有限差分法推出地基土在极限状态时的有限差分公式,结合边界条件编制出地基承载力计算程序,该程序求解条形地基极限状态下的滑移线区域及相应的地基极限承载力值时可以考虑基础埋深、地基土重度、土的内摩擦角、基础与地基摩擦等参数。利用程序,得到了土的内摩擦角与地基承载力系数N? 的对应表,并全面讨论了基础埋深、地基土重度、内摩擦角及基础与地基摩擦角等参数对地基承载力和滑移线形状的影响,得到了一些有意义的结论。 相似文献
17.
西南地区常见碎石土-基岩斜坡地基,在此类地基上的嵌岩桩基础,其上覆土层、嵌固段基岩多为倾斜。然而岩石试样中结构面倾角改变时,岩石试样的强度也随之发生变化。故当嵌固段基岩存在层面且层面具有倾角时,往往对桩基的水平承载特性影响很大,所以基岩层面是影响嵌岩桩水平承载性能的主要因素之一。本文采用物理模型试验,通过改变嵌固段基岩层面倾角,得出嵌固段基岩不同层面倾角对于桩顶位移,桩身内力的发展规律,进而研究其对水平受荷嵌岩桩承载性能的影响。试验结果表明:在碎石土-层状基岩斜坡地基场地中,嵌固段基岩存在层面会降低嵌岩桩水平承载性能。相对于完整基岩,嵌固段层状基岩存在水平层面时,临界荷载下降了17%、最大弯矩值下降了23%、最大剪力值下降了37.5%;而嵌固段基层层面为倾斜时,嵌岩桩水平承载性能下降的更多,且层面倾角为逆向30°时比顺向30°更加不利于嵌岩桩的水平受荷;桩身最大弯矩点与最大剪力点位置随嵌固段层状基岩倾角变化影响比较小,最大弯矩点位置几乎没有变化,最大剪力点位置在嵌固段基岩层面为顺向30°与逆向30°时下降了1倍桩径。该项研究可为在不同层面倾角下的层状岩体斜坡地基上受水平荷载的嵌岩桩设计作一定的指导。 相似文献
18.
Deepankar Choudhury Kanakapura. S. Subba Rao 《Geotechnical and Geological Engineering》2004,22(1):59-72
Uplift capacity of horizontal strip anchors in soil embedded under an inclined ground surface has been obtained under seismic
conditions. Limit equilibrium approach with logspiral failure surface together with pseudo-static seismic forces has been
adopted. The results have been presented in the form of seismic uplift capacity factors as functions of ground inclination,
embedment ratio, angle of internal friction of the soil and seismic acceleration coefficients. The uplift capacity factors
have been worked out separately for cohesion, surcharge and density components. Effect of the vertical seismic acceleration
coefficient has been found to always reduce the uplift capacity whereas the effect of horizontal seismic acceleration coefficient
has been found to reduce the uplift capacity in most of the cases. The obtained results of seismic uplift capacity factors
are found to be the minimum when compared with the results available in literature on the basis of planar failure surface.
This revised version was published online in July 2006 with corrections to the Cover Date. 相似文献
19.
This paper presents a study on the bearing capacity of eccentrically-loaded rough ring footings resting over cohesionless soil. To this aim, a series of 3D numerical simulations were performed using the finite difference method. In order to consider the effect of load eccentricity, reduction factor method is applied. In this method, the ratio of an eccentrically-loaded bearing capacity to the bearing capacity of the same footing under vertical load is defined. Comparison between the results of the numerical simulations with those of analytical solutions and experimental data indicates good agreement. A mathematical expression is also introduced for eccentrically-loaded ring footings. 相似文献
20.
Experimental Study of Bearing Capacity of Granular Soils,Reinforced with Innovative Grid-Anchor System 总被引：1，自引：0，他引：1
Mansour Mosallanezhad Nader Hataf Arsalan Ghahramani 《Geotechnical and Geological Engineering》2008,26(3):299-312
The pull-out resistance of reinforcing elements is one of the most significant factors in increasing the bearing capacity
of geosynthetic reinforced soils. In this research a new reinforcing element that includes elements (anchors) attached to
ordinary geogrid for increasing the pull-out resistance of reinforcements is introduced. Reinforcement therefore consists
of geogrid and anchors with cubic elements that attached to the geogrid, named (by the authors) Grid-Anchor. A total of 45
load tests were performed to investigate the bearing capacity of square footing on sand reinforced with this system. The effect
of depth of the first reinforcement layer, the vertical spacing, the number and width of reinforcement layers, the distance
that anchors are effective, effect of relative density, low strain stiffness and stiffness after local shear were investigated.
Laboratory tests showed that when a single layer of reinforcement is used there is an optimum reinforcement embedment depth
for which the bearing capacity is the greatest. There also appeared to be an optimum vertical spacing of reinforcing layers
for multi-layer reinforced sand. The bearing capacity was also found to increase with increasing number of reinforcement layer,
if the reinforcement were placed within a range of effective depth. The effect of soil density also is investigated. Finally
the results were compared with the bearing capacity of footings on non-reinforced sand and sand reinforced with ordinary geogrid
and the advantages of the Grid-Anchor were highlighted. Test results indicated that the use of Grid-Anchor to reinforce the
sand increased the ultimate bearing capacity of shallow square footing by a factor of 3.0 and 1.8 times compared to that for
un-reinforced soil and soil reinforced with ordinary geogrid, respectively. 相似文献