共查询到20条相似文献，搜索用时 62 毫秒
1.
非均质地基承载力及破坏模式的FLAC数值分析 总被引：3，自引：0，他引：3
利用基于Lagrangian显式差分的FLAC算法，通过数值计算，对黏结力随深度线性增长的非均质地基上条形基础和圆形基础的极限承载力及地基破坏模式进行了对比计算与系统分析。研究表明：（1）随着地基黏结力沿深度非均匀变化系数的增大，地基的破坏范围逐渐集中在地基表层和基础两侧：（2）即使地基的非均质程度较小，当将非均质地基近似地按均质地基考虑时，由此所估算的承载力可能过于保守；（3）地基承载力系数随黏结力沿深度非均匀变化系数的增大而非线性地增大。与数值解相比，skempton与Peck等近似公式均可能高估了非均质地基承载力。 相似文献
2.
基于传统的极限平衡条分法,利用临界滑动场法计算了条形基础的加筋地基极限承载力。假定土体处于极限平衡状态时,土体与筋材间存在均匀的摩擦力,通过建立土体条块极限平衡方程,推导了地基承载力的递推关系式。首先,设定计算土体范围,并划分条块和离散状态点;其次,根据递推公式计算各个状态点的参数,并搜索临界滑面;最后,根据搜索出的滑面计算地基承载力。通过实例比较进一步验证了计算结果的可靠性,并分析了首层筋带埋深、铺设层数和长度对地基承载力和滑面位置的影响。研究结果表明：地基承载力随着筋带埋深的增加先增大后减小;随着层数和长度的增加先逐渐增大,最后趋于稳定;滑面位置的变化规律主要是垂直影响深度和水平影响范围增大或减小。该方法原理简单、易于编程,为条形基础加筋地基承载力的计算提供了一种新思路,是临界滑动场法在地基承载力计算中的推广应用。 相似文献
3.
临坡地基已成为一种广泛的地基形式。针对临坡条形基础地基破坏模式的非对称性特点,首先引进双侧破坏模式的研究思路,重点考虑临坡地基基础两侧滑块大小和同一滑块几何形状的双重非对称性特征,构建了临坡条形基础地基非对称双侧破坏模式,为临坡地基承载力分析奠定了坚实基础;然后在此基础上,引进极限上限分析和优化理论,建立了临坡条形基础地基承载力分析的模型与方法,该方法不仅可考虑地基破坏模式,还可考虑基础与坡顶距离对临坡地基承载力的影响,而且还可较好地蜕化为平地地基承载力的分析;最后通过工程实例计算,并与现有相关分析方法进行对比分析,表明该方法的可行性与合理性以及普遍适用性。 相似文献
4.
Bearing Capacity of Embedded Strip Footings on Cohesionless Soil Under Vertical and Horizontal Loads
Hadjer Yahia-Cherif Abdelhak Mabrouki Djamel Benmeddour Mekki Mellas 《Geotechnical and Geological Engineering》2017,35(2):547-558
In the last decades a few attention was given to the evaluation of the bearing capacity of embedded footing under inclined loads on a frictional soil. This paper focuses on a numerical study using the finite-difference code Fast Lagrangian Analysis of Continua (FLAC), to evaluate the bearing capacity of embedded strip footing on a frictional soil. The soil is modeled by an elasto-plastic model with a Mohr–Coulomb yield criterion and associative flow rule; the effect of non-associativity of the soil on the bearing capacity is also investigated. The effect of the embedment is estimated though a depth factor, defined as a ratio of the bearing capacity of a strip footing at a depth D to that of a strip footing at the ground surface. The inclination effect is estimated by inclination factors, defined as the ratio of the limit vertical load for a footing under inclined loading to that of the vertically loaded footing. Both swipe and probe analyses were carried out to identify the vertical force–horizontal force (V–H) failure envelope. The results have been compared with those available in the literature. 相似文献
5.
In this paper, an effort is made to evaluate the seismic bearing capacity of shallow strip footing resting on c–ф soil. The formulation is developed to get a single coefficient of bearing capacity for simultaneous resistance of weight, surcharge and cohesion. Limit equilibrium method in Pseudo-static approach with Coulomb mechanism is applied here to evaluate the seismic bearing capacity. The seismic bearing capacity of footing (quE) is expressed in terms of single coefficient NγE. The effect of various parameters viz. angle of internal friction of soil (ф), angle of wall friction (δ), cohesion (c), ratio of depth to width of footing (df/B0), seismic acceleration (kh, kv) are studied on the variation of seismic bearing capacity co-efficients. 相似文献
6.
Experimental and numerical investigations into the bearing capacity of circular footing on geogrid-reinforced compacted granular fill layer overlying on natural clay deposit have been conducted in this study. A total of 8 field tests were carried out using circular model rigid footing with a diameter of 0.30 m. 3D numerical analyses were performed to simulate soil behavior using finite element program Plaxis 3D Foundation. The results from the FE analysis are in very good agreement with the experimental observations. It is shown that the degree of improvement depends on thickness of granular fill layer and properties and configuration of geogrid layers. Parameters of the experimental and numerical analyses include depth of first reinforcement, vertical spacing of reinforcement layers. The results indicate that the use of geogrid-reinforced granular fill layers over natural clay soils has considerable effects on the bearing capacity and significantly reduces the lateral displacement and vertical displacement of the footing. 相似文献
7.
Ahmad Safuan A. Rashid Mohammad Gharehzadeh Shirazi Hisham Mohamad Fauzan Sahdi 《Environmental Earth Sciences》2017,76(12):431
Bio-based materials are widely used recently in order to introduce a more sustainable construction material. Kenaf is a type of bio-based material that can be easily obtained in a tropical country, which could be a potential material to be utilised as a geotextile material because it has good tensile strength. The geotextile could be used to improve the bearing capacity of a loose soil. This paper presents a series of small-scale physical modelling tests to investigate the bearing capacity performance of Kenaf fibre geotextile laid on and inside the sand layer. A rigid footing was used to replicate a strip footing during the loading test, and sand was prepared based on 50% of relative density in a rigid testing chamber for ground model preparation. In order to treat the soil, Kenaf fibre geotextile was laid at four difference locations which are on the soil surface and underneath the ground model surface at 50, 75 and 100 mm deep. It was found that the usage of the Kenaf fibre geotextile has improved the bearing capacity of the sandy soil up to 414.9% as compared to untreated soil. It was also found that the depth of the Kenaf fibre geotextile treated into the soil also affects the soil performance. 相似文献
8.
Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study using the finite-difference code Fast Lagrangian Analysis of Continua (FLAC), to evaluate the bearing capacity for two interfering strip footings, subjected to centered vertical loads with smooth and rough interfaces. The soil is modeled by an elasto-plastic model with a Mohr–Coulomb yield criterion and associative flow rule. The interference effect is estimated by efficiency factors, defined as the ratio of the bearing capacity for a single footing in the presence of the other footing to that of the single isolated footing. The efficiency factors have been computed individually to estimate the effects of cohesion, surcharge, and soil weight using Terzaghi’s equation, both in a frictional soil with surcharge pressures and in a cohesive-frictional soil with surcharge pressures. The results have been compared with those available in the literature. 相似文献
9.
《Geomechanics and Geoengineering》2013,8(2):151-162
In this paper, finite element analysis is used to predict the undrained bearing capacity of strip, square and circular footings resting on layered clays. The soil profile consists of two clay layers with different thicknesses and properties. The results are compared with previous solutions for strip footings on layered clays. The bearing-capacity behaviour is discussed and the bearing-capacity factors are given for various cases involving a range of layer thicknesses and properties of the two clay soil layers. 相似文献
10.
In the present study, an approximate method has been suggested to calculate the ultimate bearing capacity of a square footing
resting on reinforced layered soil. The soil is reinforced with horizontal layers of reinforcement in the top layer of soil
only. The pre requisite to the method is the ultimate bearing capacity of unreinforced layered soil, which can be determined
from the methods already available in literature. The results have been validated with the model tests conducted on two layered
soil compacted at different densities and the top layer reinforced with horizontal layers of geogrid reinforcement. 相似文献
11.
Reliability analysis of bearing capacity of a strip footing at the crest of a simple slope with cohesive soil was carried out using the random finite element method (RFEM). Analyses showed that the coefficient of variation and the spatial correlation length of soil cohesion can have a large influence on footing bearing capacity, particularly for slopes with large height to footing width ratios. The paper demonstrates cases where a footing satisfies a deterministic design factor of safety of 3 but the probability of design failure is unacceptably high. Isotropic and anisotropic spatial variability of the soil strength was also considered. 相似文献
12.
建筑物或构筑物基础临近边坡置放的情况在实际工程中十分普遍,但目前对于临近边坡基础的地基承载力及破坏模式尚缺乏深入研究。采用不连续布局优化（DLO）极限分析法建立数值模型,分析边坡几何尺寸、土体参数和基础位置对临坡条形基础的极限承载力和边坡破坏模式的影响,并对国内外现行规范推荐的计算方法进行评价。结果表明：极限承载力随边坡高度和边坡倾斜角的增大而减小,当坡高超过临界高度后,极限承载力将不受其影响;极限承载力随土体黏聚力和内摩擦角的增大而提高,滑动面随黏聚力的增大而变浅,随内摩擦角的增大而变深;极限承载力随基础与坡肩相对距离的增大而提高,当基础置放位置超过某临界距离后极限承载力不受边坡影响。在土体强度高、坡角较大时,《建筑地基基础设计规范》规定的临坡基础最小置放距离偏于危险,设计时仍需考虑边坡对承载力的减损作用;在土体强度较低、坡角较小时,规范规定值偏于保守。美国AASHTO规范对边坡地基极限承载力的取值在砂土边坡时较为可靠,但其仅适用于坡面破坏模式的情况;饱和黏土边坡的承载力曲线有悖于理论解,对临界距离的规定同样存在低估。 相似文献
13.
《Geomechanics and Geoengineering》2013,8(2):107-111
The stability of eccentrically loaded strip footings on slopes was investigated using the method of finite element analysis based on the theory of elasto-plasticity. The analysis was done for two different soils involving three levels of slope angle, six footing locations, and two levels of load eccentricity plus central vertical loading. The strip footing analysed was a 3-ft (0.9 m) wide reinforced concrete footing embedded to a depth of 3 ft (0.9 m). The analysis focused on footing settlement, plastic yielding of soil, and ultimate bearing capacity. The results of analysis show that the influence of load eccentricity on footing pressure vs. footing centre settlement is negligibly small. However, the progressive soil yielding and ultimate bearing capacity are greatly affected by load eccentricity. Furthermore, the effect of load eccentricity differs considerably with the load location relative to the footing centre and slope crest. The ultimate bearing capacity for the eccentric load located on the slope side is significantly greater than that for the load located on the other side of the footing centre. For a 2(H): 1(V) slope in silty clay, the effect of slope on footing stability decreases with increasing footing location from slope crest as would be expected, and diminishes when the footing is located from the crest at about 5-times the footing width. 相似文献
14.
Bearing capacity of strip footings on spatially random soils using sparse polynomial chaos expansion
A probabilistic model is presented to compute the probability density function (PDF) of the ultimate bearing capacity of a strip footing resting on a spatially varying soil. The soil cohesion and friction angle were considered as two anisotropic cross‐correlated non‐Gaussian random fields. The deterministic model was based on numerical simulations. An efficient uncertainty propagation methodology that makes use of a non‐intrusive approach to build up a sparse polynomial chaos expansion for the system response was employed. The probabilistic numerical results were presented in the case of a weightless soil. Sobol indices have shown that the variability of the ultimate bearing capacity is mainly due to the soil cohesion. An increase in the coefficient of variation of a soil parameter (c or φ) increases its Sobol index, this increase being more significant for the friction angle. The negative correlation between the soil shear strength parameters decreases the response variability. The variability of the ultimate bearing capacity increases with the increase in the coefficients of variation of the random fields, the increase being more significant for the cohesion parameter. The decrease in the autocorrelation distances may lead to a smaller variability of the ultimate bearing capacity. Finally, the probabilistic mean value of the ultimate bearing capacity presents a minimum. This minimum is obtained in the isotropic case when the autocorrelation distance is nearly equal to the footing breadth. However, for the anisotropic case, this minimum is obtained at a given value of the ratio between the horizontal and vertical autocorrelation distances. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
15.
利用极限分析上限法求解地基极限承载力问题的关键在于构造合适的破坏模式。当地基下方存在空洞时,地基的破坏模式变得相当复杂。通过分析空洞存在时地基的受力特点及破坏形态,将地基破坏范围划分成为不同的刚性区和过渡区,构造了空洞上方条形基础地基的破坏模式。利用上限法,建立与破坏模式对应的速度场,推导了破坏模式不同区域内的耗散功率和外力功率,得到地基极限承载力的目标函数,并采用数学优化方法进行求解,获得了极限承载力的上限解。通过算例分析,讨论了空洞顶板厚度、空洞大小与地基极限承载力的关系,并与无空洞条件下地基极限承载力进行对比分析。结果表明,随着空洞顶板厚度增加,地基极限承载力增加,破坏模式也由地基与空洞之间扩散到地基两侧;空洞顶板厚度存在临界值,当超过此临界值时,空洞对地基极限承载力的影响可忽略。 相似文献
16.
K. Z. Andrawes R. R. Al-Omari W. M. Kirkpatrick 《Geotechnical and Geological Engineering》1996,14(3):227-236
The effect of a smooth rigid stratum, located beneath a dense sand layer, on the bearing capacity and settlement of surface and shallow strip footings is investigated using an advanced experimental model. A theoretical analysis is presented for the bearing capacity of surface footings. The results indicate that the bearing capacity reaches a minimum value at a specific sand-layer thickness. Any increase in the layer thickness above this value causes an increase in the bearing capacity up to that corresponding to a continuous media.Notation
H=
thickness of the sand layer
-
B=
foundation width
-
N
q and N
=
bearing capacity factors for a semi-infinite layer
-
N
qs and N
s=
bearing capacity factors for a finite layer
-
H
o
/B=
limiting depth
-
D
r=
relative density
- =
angle of soil internal friction
-
M=
model width
-
D=
depth of surcharge
-
q=
bearing stress, pressure applied on the footing
-
q
u=
bearing capacity
- =
unit weight of sand 相似文献
17.
Arash Alimardani Lavasan Ali Talsaz Mahmoud Ghazavi Tom Schanz 《Geotechnical and Geological Engineering》2016,34(6):1791-1805
This paper numerically examines the bearing capacity and failure mechanism of a shallow strip foundation constructed above twin voids. The voids may refer to caves, caverns, underground aqueduct or tunnels due to water seepage, chemical reaction or deliberately excavated in soil deposit. The ability of numerical model to accurately predict the system behavior is evaluated by performing verification analyses on existing researches. Subsequently, a parametric study carried out to reveal the influence of size of footing/voids and their location (i.e. depth, spacing, eccentricity) on the bearing capacity of footing. To clarify the failure mechanism, the distribution of shear strain in the soil for different scenarios is assessed. The parametric study provided a new framework to determine the bearing capacity and the mode of failure for footings on voids. Based on the results, a criterion can be issued to avoid collapse of footing/voids regarding the shape, location and size of voids. The results can also be used to design construction of a footing on existing voids while the acquired failure mechanisms can be appointed to develop analytical solutions for this problem. Results demonstrated that a critical depth for voids and a critical distance between them exist where the influence on the ultimate bearing capacity of footing disappears. 相似文献
18.
《Geomechanics and Geoengineering》2013,8(4):274-285
By applying the lower bound finite element limit analysis in conjunction with non-linear optimisation, the bearing capacity factors, Nc, Nq and Nγ, due to the components of cohesion, surcharge and unit weight, respectively, have been estimated for a horizontal strip footing placed along a sloping ground surface. The variation of Nc, Nq and Nγ with changes in slope angle (β) for different soil friction angle (φ) have been computed for smooth as well as rough strip footings. The analysis reveals that along a sloping ground surface, in addition to Nγ, the factors Nc and Nq also vary considerably with changes in footing roughness. Compared to the smooth footing, the extent of the plastic zone around the footing becomes greater for the rough footing. The results obtained from the analysis are found to compare well with those previously reported in literature. 相似文献
19.
软土地基上高填方刚性涵洞地基承载力分析 总被引：2，自引：0，他引：2
山区沟谷软土地基上高填方刚性涵洞的应用较为广泛,然而,现有的计算理论对该类条件下涵洞地基承载力的认识还不够充分,对地基承载力提出过高的要求,反而为结构带来了不利影响。通过数值模拟和试验手段对涵洞的地基承载力进行深入分析。探讨基础埋深、宽度及软土固结对涵洞地基承载力的影响。研究表明,当基础埋深系数 5时,涵洞地基承载力特征值随着基础埋深的增大近似线性增加,当 5时,基础埋深对地基承载力特征值影响逐渐减小;但基础宽度对软土地基上刚性涵洞地基承载力特征值的影响甚小,实际工程中可不予考虑。此外,试验结果表明,固结度和固结压力对软土的黏聚力和内摩擦角有复合影响,固结度较大时,黏聚力和内摩擦角随固结压力的增大而明显增大。固结度和固结压力对内摩擦角的影响比对黏聚力的影响要大。高填方涵洞地基极限承载力随着软土固结度的增大而提高,当固结度达到90%时,地基极限承载力通常可提高36%以上;地基极限承载力随固结压力的增加呈非线性增大,其提高的幅度逐渐减小。 相似文献
20.
通过构建一种网格状多刚性块破坏机制,利用上限法研究了黏土地基各向异性和非均质对粗糙条形基础地基承载力的影响。该破坏机制允许滑动面和速度矢量沿破坏区域过渡区的径向和切向发生变化,形成了更为精确的破坏机制和塑性流动速度场。根据上限定理得到各向异性和非均质性黏土上条形基础极限承载力的目标函数,将其转化为非线性规划问题,并通过编程对该计算模型进行求解。与已有研究成果对比分析表明,两者具有较好一致性,且优于现有同类方法。文中亦探讨了黏土地基非均质、各向异性以及其他相关参数对地基承载力的影响。 相似文献