共查询到20条相似文献，搜索用时 46 毫秒
1.
劈裂注浆作为一种有效的土体加固方法,其理论研究落后于工程实践。提出了基于弥散裂缝模型和流体体积法的劈裂注浆有限元分析方法,并通过ABAQUS二次开发编写劈裂注浆有限元程序。数值分析结果能与室内试验较好吻合,验证了有限元算法的合理性。在此基础上研究了注浆孔埋深和注浆流量对劈裂浆脉形状的影响。结果表明,劈裂注浆过程可分为起劈和劈裂发展两个阶段。当劈裂浆脉扩展到模型边界后,继续注浆会引起注浆压力的大幅提高和已有浆脉宽度的增加。随着注浆孔埋深的增加,浆脉分支减少,长度减小,宽度增加,劈裂浆脉形状的主要控制因素从土体参数的随机性变成大小主应力值的差异。注浆量一定的情况下,注浆速率越大,劈裂浆脉长度越短,宽度越大,注浆终压也越大。研究为劈裂注浆的工程应用提供理论支撑。 相似文献
2.
水平旋喷桩施工引起周围土体变形分析 总被引：1，自引：0，他引：1
水平旋喷桩施工期间,大量高压流体注入土层,引起土层内部产生较大的膨胀作用,致使周围一定区域的土体发生变形。水平旋喷桩施工引起土体变形可以归结为压力膨胀和体积膨胀共同作用的问题。依托单根水平旋喷桩施工的现场实例,建立了水平旋喷桩施工引起土体变形的数值模型。将水平旋喷桩施工引起的土体变形问题简化为圆孔的膨胀问题,可以统筹考虑注浆压力和注浆流量的影响。首先需要确定注浆压力的影响半径和注浆流量引起的体积膨胀比,然后可以通过数值模型计算膨胀引起的土体变形。数值分析结果与现场实测值的对比表明,当注浆压力影响半径为成桩半径的6倍时,数值计算结果与现场实测值吻合较好。 相似文献
3.
控制隧道开挖引起的土体沉降变形是劈裂注浆的主要目的之一,隧道在劈裂注浆后复合土体的等效弹性参数取值直接关系着隧道在劈裂注浆后沉降变形的预测精度。首先在对已有劈裂扩散模型研究的基础上,按面积等效原则提出了隧道劈裂注浆后复合土体的二维简化等效单元体模型,并基于均质化理论按变形协调原则推导了二维简化单元体模型的等效弹性参数解析解。然后采用有限元方法分别计算并分析了模型在简化前后的等效弹性参数;同时把二维简化等效单元体模型的有限元计算结果和解析计算结果也做了对比分析。最后基于解析结果分析了土体和浆液结石体各自的弹性参数以及浆液注入率对等效弹性参数的影响。结果表明：（1）按面积等效原则对模型进行简化处理的方法是可行的,可以按照简化模型进行弹性阶段的理论分析;（2）解析结果与有限元结果具有良好的一致性,说明了解析结果的合理性;（3）复合土体的等效弹性模量和等效泊松比主要受浆液注入率和浆液固结体本身模量的影响;浆液固结体的泊松比对等效弹性模量的影响几乎可以忽略。 相似文献
4.
Today, grouting is used as an aid in ground improvement in most civil and mining engineering projects. Groutability and grout penetration depth are among the most important issues that are considered in grouting operation. Various parameters such as in-situ stress, pore water pressure, joint geometric and geomechanical characteristics, grout properties (viscosity and yield stress) and technical factors such as grouting pressure and flow rate affect the groutability and grout penetration depth in a jointed rock mass. Knowledge of the effect of these parameters has advantages in the prediction of grouting results. Typically, cement-based grout is used in jointed rock masses. Unlike water, stable cement-based grout usually acts as a Bingham fluid. In this study the effect of important parameters on grouting process in a jointed rock mass was investigated numerically using the DEM method. In the conducted study, the problem geometry represents a horizontal section in a regularly jointed rock mass with two joint sets. The analyses results show that the grout penetration depth and intake increase as joint aperture, normal stiffness and grouting pressure increase and in-situ stress and pore water pressure decrease. Increase in joint spacing does not have any effect on the grout penetration depth but decreases the grout intake. The effect of joint orientation on grouting process is strongly dependent on in-situ stress state. On the other hand, increase in grout yield stress decreases the grout penetration depth and intake, while grout viscosity does not have any effect on maximum grout penetration depth and intake. To further investigate the above mechanisms, the grouting process conducted in Gotvand dam-Iran was simulated numerically. 相似文献
5.
渗流-化学溶解耦合作用下岩石单裂隙渗透特性研究 总被引：3，自引：0，他引：3
为揭示在渗流-化学溶解耦合作用下单裂隙渗透特性的变化规律,建立了描述二维渗流-化学溶解耦合作用的偏微分方程组,并利用COMSOL Multiphysics软件成功地求解该方程组。首先,模拟了文献[1]中的盐岩渗流-溶解耦合渗流试验结果,数值模拟结果与试验结果较为吻合,验证了数学模型的正确性和有效性。然后,利用分形理论生成了一个粗糙的裂隙面数字模型,着重分析了二维石灰岩粗糙裂隙面在水流、矿物溶解和输运过程中其渗透特性的变化规律。数值分析显示,（1）溶质浓度对裂隙面的溶解具有非常重要的作用,从而水流进口端的溶解厚度比出口端大得多。（2）裂隙的整体渗透性在初始时刻增加较慢,随着裂隙开度的增大和贯通,溶解速度会逐渐增大,是一个加速的过程。 相似文献
6.
Analysis of shield tunnel 总被引：1，自引：0，他引：1
This paper proposes a two‐dimensional finite element model for the analysis of shield tunnels by taking into account the construction process which is divided into four stages. The soil is assumed to behave as an elasto‐plastic medium whereas the shield is simulated by beam–joint discontinuous model in which curved beam elements and joint elements are used to model the segments and joints, respectively. As grout is usually injected to fill the gap between the lining and the soil, the property parameters of the grout are chosen in such a way that they can reflect the state of the grout at each stage. Furthermore, the contact condition between the soil and lining will change with the construction stage, and therefore, different stress‐releasing coefficients are used to account for the changes. To assess the accuracy that can be attained by the method in solving practical problems, the shield tunnelling in the No. 7 Subway Line Project in Osaka, Japan, is used as a case history for our study. The numerical results are compared with those measured in the field. The results presented in the paper show that the proposed numerical procedure can be used to effectively estimate the deformation, stresses and moments experienced by the surrounding soils and the concrete lining segments. The analysis and method presented in this paper can be considered to be useful for other subway construction projects involving shield tunnelling in soft soils. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
7.
8.
富水断裂带优势劈裂注浆机制及注浆控制方法研究 总被引：3，自引：0，他引：3
注浆是处治隧道塌方、突水突泥等地质灾害的有效手段,但对于岩体结构多样、结构面发育的富水断裂带,注浆理论及控制技术尚不成熟。基于富水断裂带内部岩体结构,建立了注浆概念模型,提出了优势劈裂注浆概念。基于广义宾汉流体本构方程,建立单一平板优势劈裂注浆扩散模型,推导了考虑浆液流变特征的优势劈裂注浆扩散控制方程。由方程可知,注浆速率、注浆压力及浆液黏度是影响注浆扩散的3个主控因素。深入分析了优势劈裂注浆过程中3个主控因素对注浆扩散的影响规律,基于此提出优势劈裂注浆控制方法,形成了注浆压力差异控制、控制液动态调节及注浆速率梯度控制3项关键技术,促使浆液在优势结构面内控制性扩散。研究成果成功应用于江西省某隧道断裂带塌方处治工程中,取得良好治理效果,对隧道断裂带地质灾害控制理论研究和工程实践具有一定指导意义。 相似文献
9.
采用裂隙动水注浆设备结合正交试验设计进行了裂隙动水注浆模型试验,获得了渗流压力场与注浆效果和注浆工艺之间的相关关系。结果表明,裂隙动水注浆的渗流压力场包括单峰型、平台型、多峰型、阶梯型4种类型;出现平台型和多峰型渗流压力场时的注浆堵水效果好,而出现阶梯型渗流压力场时的注浆堵水效果差;为了获得好的注浆效果且节约浆液,在渗流压力场为单峰型时应该适量增加注浆量;而在渗流压力场为平台型或多峰型时应该适量减小注浆量;渗流压力场为阶梯型时应该调节浆液配比,缩短凝胶时间。研究结果对应用压力监测及时控制施工质量和调整注浆工艺有指导作用。 相似文献
10.
Qiong Wang Xinyu Ye Shanyong Wang Scott William Sloan Daichao Sheng 《Acta Geotechnica》2018,13(5):1129-1140
This paper presents a non-destructive, low-cost, photo-based, 3D reconstruction technique for characterizing geo-materials with irregular shapes of a relatively large size. After being validated against two traditional volume measurement methods, namely the vernier caliper method and the fluid displacement method for regular and irregular shapes, respectively, 3D photogrammetry was used to analyse the grout bulbs formed in laboratory pressure grouting tests. The reconstructed 3D mesh model of the sample provides accurate and detailed 3D vertex data, which allowed the volume, densification efficiency and bleeding behaviour of the grout bulbs to be analysed. Comparing the bulb section views at different grouting pressures also offers an intuitive observation of the grout development and propagation process. Moreover, the 3D vertex data and surface area included in the model are of great importance in validating numerical predictions of the pressure grouting process and analysing the interface shear resistance of grouted soil nails or anchors. Compared to existing approaches, the new 3D photogrammetry method possesses several key advantages: (a) it does not require expensive, specialized equipment; (b) samples are not destroyed or modified during testing; (c) it allows to reconstruct objects of various scales and (d) the software is public domain. Therefore, the adoption of this 3D photogrammetry method will facilitate research in the pressure grouting process and can be extended to other problems in geotechnical engineering. 相似文献
11.
考虑黏度时变性的水泥浆液盾构壁后注浆扩散规律及管片压力模型的试验研究 总被引：3，自引：0，他引：3
对水泥浆液黏度时变性进行了试验研究,证实了工程常用水灰比范围内水泥浆液服从宾汉姆流体特性;不同水灰比浆液黏度均随注浆时间增大而大幅度增加。根据试验结果,考虑注浆过程中水泥浆液黏度随时间的变化,对盾构壁后注浆水泥浆液的扩散规律及因注浆而造成的管片压力进行了推导及分析。计算表明：相同注浆时间条件下,水泥浆液扩散半径及注浆对管片产生的压力值均随注浆压力的增大而增大。考虑浆液黏度时变性后,扩散半径、注浆对管片压力值等均较不考虑浆液时变性时减小,且随注浆压力的增大,浆液黏度变化对管片压力值的影响更加明显。相同注浆压力条件下,浆液扩散半径及对管片产生的压力值均随注浆时间的增长而增加,但注浆前期增长速度较快,而后逐渐减缓。研究成果对于盾构壁后注浆工艺选择及参数设计具有较大的指导意义。 相似文献
12.
13.
浆液在多孔介质中的扩散路径对渗透扩散范围和注浆效果具有非常重要的影响。采用理论分析,以分形特征与宾汉姆流体在多孔介质中的渗流运动方程为基础,揭示了考虑扩散路径的宾汉姆流体渗透注浆机制,并利用团队前期开展的渗透注浆试验对其进行了验证。分析了多孔介质孔隙率、宾汉姆水泥浆液水灰比、多孔介质渗透系数、注浆压力、地下水压力等对扩散半径的影响变化规律。同时,基于Comsol Multiphysics平台,采用计算机编程技术二次开发得到了考虑扩散路径的宾汉姆流体渗透注浆机制的渗透注浆三维数值模拟程序,并以此开展了宾汉姆水泥浆液在多孔介质中渗透扩散形态效果的数值模拟。研究结果表明：与不考虑扩散路径的宾汉姆流体渗透注浆球形扩散公式获得的扩散半径理论计算值相比,采用考虑扩散路径的宾汉姆流体渗透注浆机制得到的扩散半径理论计算值更接近试验值。该研究成果可为实践注浆工程提供一定的理论支撑。 相似文献
14.
Numerical Simulation of 3D Hydraulic Fracturing Based on an Improved Flow-Stress-Damage Model and a Parallel FEM Technique 总被引：4，自引：4，他引：0
L. C. Li C. A. Tang G. Li S. Y. Wang Z. Z. Liang Y. B. Zhang 《Rock Mechanics and Rock Engineering》2012,45(5):801-818
The failure mechanism of hydraulic fractures in heterogeneous geological materials is an important topic in mining and petroleum engineering. A three-dimensional (3D) finite element model that considers the coupled effects of seepage, damage, and the stress field is introduced. This model is based on a previously developed two-dimensional (2D) version of the model (RFPA2D-Rock Failure Process Analysis). The RFPA3D-Parallel model is developed using a parallel finite element method with a message-passing interface library. The constitutive law of this model considers strength and stiffness degradation, stress-dependent permeability for the pre-peak stage, and deformation-dependent permeability for the post-peak stage. Using this model, 3D modelling of progressive failure and associated fluid flow in rock are conducted and used to investigate the hydro-mechanical response of rock samples at laboratory scale. The responses investigated are the axial stress–axial strain together with permeability evolution and fracture patterns at various stages of loading. Then, the hydraulic fracturing process inside a rock specimen is numerically simulated. Three coupled processes are considered: (1) mechanical deformation of the solid medium induced by the fluid pressure acting on the fracture surfaces and the rock skeleton, (2) fluid flow within the fracture, and (3) propagation of the fracture. The numerically simulated results show that the fractures from a vertical wellbore propagate in the maximum principal stress direction without branching, turning, and twisting in the case of a large difference in the magnitude of the far-field stresses. Otherwise, the fracture initiates in a non-preferred direction and plane then turns and twists during propagation to become aligned with the preferred direction and plane. This pattern of fracturing is common when the rock formation contains multiple layers with different material properties. In addition, local heterogeneity of the rock matrix and macro-scale stress fluctuations due to the variability of material properties can cause the branching, turning, and twisting of fractures. 相似文献
15.
水泥基速凝浆液广泛应用于富水裂隙围岩注浆工程。为研究水泥基速凝浆液在裂隙注浆中的扩散机制与压力特性,选取水泥-水玻璃浆液及高聚物改性水泥浆液,采用不同水灰比及混合体积,开展了静水条件下单一平板裂隙的注浆扩散模型试验,通过监测浆液的注浆扩散形态和注浆过程中不同测点的压力变化,研究了水泥基速凝浆液的静水扩散规律和注浆扩散压力分布规律。试验结果表明,水泥-水玻璃浆液和高聚物改性水泥浆液具有相似的扩散形态和压力分布变化,两者的显著差别在于高聚物改性水泥浆液扩散所需的注浆压力明显小于水泥-水玻璃浆液,且凝结固化时间相对较长,有利于延长注浆扩散距离。研究结果应用于张马屯铁矿注浆堵水工程,解决了裂隙岩体渗漏水问题,实现了围岩稳定性控制。研究成果具有一定的理论和实践意义,对类似工程具有参考价值。 相似文献
16.
单一裂隙动水注浆扩散模型 总被引：3，自引：0，他引：3
通过理论推导建立了单一裂隙动水注浆扩散模型,用计算机对单一裂隙动水注浆扩散模型进行编程和分析,试验验证该注浆扩散模型是合理的。研究结果表明,单一裂隙动水注浆在注浆前期浆液扩散面积呈圆形而在注浆后期浆液扩散面积呈椭圆形;浆液扩散半径与浆液黏度成反比,与裂隙开度和注浆压力成正比;水流流动有利于浆液沿顺水流方向扩散而抑制浆液沿逆水流方向扩散;水流流速增大或减小到一定程度时浆液扩散半径受水流流速的影响程度将逐渐减小;水流流动对逆水流方向扩散半径的影响程度大于顺水流方向扩散半径的影响程度;浆液扩散半径受水流流速影响最大,受裂隙开度影响次之,受注浆压力和浆液黏度的影响相对较小 相似文献
17.
The groutability depends on the properties of the grout, its injection processes, and on the mechanical properties of the soil formation. During the process of pouring cement‐based grouting into a porous medium, a variation with time occurs in the viscosity of grout suspension. In addition, the particle filtration phenomenon will limit the expansion of the grouted zone because cement particles are progressively stagnant within the soil matrix. In this paper, a closed‐form solution was derived by implementing the mass balance equations and the generalized phenomenological filtration law, which can be used to evaluate the deposition of cement‐based grout in the soil matrix. The closed‐form solution relevant to a particular spherical flow was modified by a step‐wise numerical calculation, considering the variable viscosity caused by a chemical reaction, and the decrease in porosity resulting from grout particle deposition in the soil pores. A series of pilot‐scale chamber injection tests was performed to verify that the developed step‐wise numerical calculation is able to evaluate the injectable volume of grout and the deposition of grout particles. The results of the chamber injection tests concurred well with that of the step‐wise numerical calculation. Based on the filtration phenomenon, a viable approach for estimating the groutability of cement‐based grout in a porous medium was also suggested, which might facilitate a new insight in the design of the grouting process. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
18.
A numerical study of the pullout behavior of grout anchors underreamed by pulse discharge technology
Pulse discharge technology (PDT) is an innovative construction method used to enhance the bearing capacity of piles and the resisting capacity of anchors by underreaming using a high-pressure shockwave induced by an underwater electric discharge. This study numerically analyzes the pullout behavior of a grout anchor underreamed by PDT. A series of finite element analyses were performed to examine the pullout behavior of the anchor based on successive simulations from underreaming to subsequent pullout tests. The electric blasting and shockwave generation by PDT was equivalently modeled using the underwater explosion (UNDEX) model, and the appropriate UNDEX parameters were determined by benchmarking the laboratory PDT tests. Full-scale PDT underreaming and the subsequent pullout tests in dry sand deposits reported in the literature were then simulated on the basis of fluid–structure interaction (FSI) analyses and static uplift analyses. The predicted expansion of the borehole and the pullout behaviors were compared with field test results to validate the numerical model. Moreover, the results from a parametric study conducted to investigate the influence of soil and anchor characteristics on the uplift behavior of the PDT underreamed anchor are discussed. 相似文献
19.
A model was developed, to describe miscible grout propagation in a saturated deformable porous medium, based on Bear's statistical model with spatial volume averaging. In a previous paper, the model was first successfully confronted to one‐dimensional laboratory experiments. In the present paper, the numerical model is used to simulate practical grouting operation in a cylindrical injection model. The cylindrical injection model lends itself to study main flow and propagation character istics for a dispersed suspension‐type grout, under axisymmetric conditions close to real scale conditions. Comparison between numerical solutions and experimental results is essential to confirm the validity and accuracy of the proposed model from a phenomenological standpoint. The numerical model performances show that the underlying mathematical model constitutes a realistic predictive model reproducing most prominent features during injection of a suspension‐type grout into a deformable porous medium. The basic mechanism by which injected miscible grout permeates a soil mass is discussed in detail. Such a tool leads to quality control criteria for grouting on a theoretical basis, which complements existing criteria acquired through engineering practice. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
20.
The propagation of hydraulic fracture in elastic rocks has widely been investigated. In the paper, we shall focus on numerical modeling of hydraulic fracturing in a class of porous rocks exhibiting plastic deformation. The plastic strain of porous rocks is described by a non-associated plastic model based on Drucker–Prager criterion. The plastic deformation is coupled with fluid pressure evolution described by the lubrication theory. An extended finite element method is used for modeling the propagation of fracture. The fracture propagation criterion is based on the J-integral. The proposed numerical model is validated by comparisons with numerical and analytical results. The influence of plastic deformation on fracture propagation process is investigated.
相似文献