共查询到20条相似文献，搜索用时 46 毫秒
1.
红层泥质胶结物在干燥条件下会因含水率变化产生开裂,裂缝进一步发展贯通最终导致红层泥岩崩解破坏。目前对红层泥岩崩解机制的研究多为定性描述,缺乏定量分析方法。因此,定量研究红层泥质胶结物开裂的产生及扩展对深化红层泥岩崩解理论研究具有重要意义。基于线弹性断裂力学及非饱和土力学,建立了考虑含水率变化的红层泥质胶结物裂缝深度及间距计算公式,并对公式参数敏感性进行了分析。应用CT试验数据对PFC2D数值模型进行了校准,并基于干缩开裂数值试验结果,对裂缝深度及间距计算公式进行了对比验证。结果表明：提出的计算公式能较好地预测红层泥质胶结物的开裂深度及间距,裂缝深度随含水率减小呈先快速增加再缓慢增长的特点。研究成果有助于加深对红层泥岩崩解的量化理论分析,并为预测工程中红层泥岩的开裂程度提供参考。 相似文献
2.
In recent times, rapid urbanisation coupled with scarcity of land forces several structures to come up ever closer to each
other, which may sometime cause severe damage to the structures from both strength and serviceability point of view, and therefore,
a need is felt to devise simplified methods to capture the effect of footing interference. In the present study, an attempt
has been made to model the settlement behaviour of two strip footings placed in close spacing on layered soil deposit consisting
of a strong top layer underlying a weak bottom layer. Theory of elasticity is employed to derive the governing differential
equations and subsequently solved by the finite difference method. The perfectly rough strip footings are considered to be
resting on the surface of two-layer soil system, and the soil is assumed to behave as linear elastic material under a range
of static foundation load. The effect of various parameters such as the elastic moduli and thickness of two layers, clear
spacing between the footings and footing load on the settlement behaviour of closely spaced footings has been determined.
The variation of vertical normal stress at the interface of two different soil layers as well as at the base of the failure
domain also forms an important part of this study. The results are presented in terms of settlement ratio (ξδ), and their variation is obtained with the change in clear spacing between two footings. The present theoretical investigation
indicates that the settlement of closely spaced footings is found to be higher than that of single isolated footing, which
further reduces with increase in the spacing between the footings. 相似文献
3.
This paper presents some experimental results on desiccation cracking tests conducted on thin layers of clay soils. Observation
of the evolution of cracking patterns was examined to clarify the transient mechanisms of the crack formation of clay soils.
Laboratory experimentation on desiccation cracking was carried out to examine experimentally the quantitative relationships
between the characteristics of soil cracks and the prevailing controlling conditions. Five desiccation cracking tests for
slurried clay soils were carried out using shrinkage moulds in a humidity chamber, which was capable of controlling relative
humidity and temperature. The soil used in the experimental studies was residual basaltic clay and was classified as a highly
reactive soil. In order to provide simple conditions for theoretical modelling, the tests were conducted in perspex and metal
moulds with rectangular cross-sections. The lengths of the moulds were considerably larger than their widths so that parallel
cracking were generated in thin layers. In each cracking test, several rectangular moulds of different thicknesses and widths
were used. Some of these tests were used for observation, crack initiation and evolution, and others for moisture content
measurement during desiccation. The test results include evolution of the cracking pattern, influences of speed of desiccation
and typical crack spacing to depth ratios for soil layers. 相似文献
4.
This paper presents a finite element parametric study of several variables that affect the stiffness efficiency of rigidly capped pile groups with a view to developing a solution for preliminary design purposes. Previous empirical solutions from linear elastic work had identified a significant dependence of stiffness efficiency on pile group size and group spacing, and in this study, the effect of the pile length-to-diameter ratio, the compressibility of a stiff bearing stratum beneath the pile group and the depth below ground level to the stiff bearing stratum are also considered. Pile groups in a soft clay/silt are modelled using PLAXIS 3D Foundation in conjunction with a soil model that captures the stress dependency of soil stiffness. The trends from the soft soil study have been formulated into a set of equations which can be used to predict the stiffness efficiency of pile groups. This new approach captures more variables than previous simpler empirical prediction methods and performs better when applied to a database of 29 published pile group case histories. 相似文献
5.
The paper presents a simple approximate analytical solution of the remote stresses that cause the collapse of a borehole or other circular cylindrical cavity in an infinite elastic space. Regions of parallel equidistant splitting cracks are assumed to form on the sides of the cavity. Their boundary is assumed to be an ellipse of a growing horizontal axis, the other axis remaining equal to the borehole diameter. The slabs of rock between the splitting cracks are assumed to buckle as slender columns, and their post-critical stress is considered as the residual stress in the cracked rock. The buckling of these slab columns is assumed to be resisted not only by their elastic bending stiffness but also shear stresses produced on rough crack faces by relative shear displacements. The energy release from the infinite medium caused by the growth of the elliptical cracking region is evaluated according to Eschelby's theorem. This release is set equal to the energy dissipated by the formation of all the splitting cracks, which is calculated under the assumption of constant fracture energy. This yields the collapse stress as a function of the elastic moduli, fracture energy, ratio of the remote principal stresses, crack shear resistance characteristic and borehole diameter. The collapse stress as a function of crack spacing is found to have a minimum, and the correct crack spacing is determined from this minimum. For small enough diameters, the crack spacing increases as the (4/5)-power of the borehole diameter, while for large enough diameters a constant spacing is approached. In contrast to plastic solutions, the breakout stress exhibits a size effect, such that for small enough diameters the breakout stress decreases as the (? 2/5)-power of the borehole diameter, while for large enough diameters a constant limiting value is approached. Finally, some numerical estimates are given and the validity of various simplifying assumptions made is discussed. 相似文献
6.
Soils, as well as most of deformable multiphase porous materials, are likely to suffer from desiccation cracking, leading to the formation of regular crack patterns affecting their permeability. The ensuing crack spacing has often been related to a concept sometimes called “sequential infilling”: it is assumed that desiccation cracks are formed by successive generations. However, such a concept does not consider the pattern of a simultaneous crack formation at a given moment. Using our desiccation cracking test results and their numerical simulation, we propose a consistent explanation for the formation of desiccation crack patterns in soils. We show that the “sequential infilling” concept is suitable only when the position of the crack(s) clearly stems from the stress field. To derive an estimate of the desiccation crack spacing, the overall energy of the system needs to be considered. Statistical variability should be superimposed on the mean deterministic conditions discussed here. 相似文献
7.
挡土墙后黏性土处于主动土压力状态时,墙顶一定深度范围内会产生裂缝,使其较大范围形成零压力区即开裂深度,关于开裂深度问题一直没有得到很好解决。针对变分法求解黏性填土主动土压力中未考虑裂缝的情况,通过一个算例说明了黏性填土表面在主动土压力状态下会产生裂缝。采用折线简化摩尔?库仑强度包络线,利用实际的土体抗拉强度推导了墙背土体开裂深度的计算公式。根据滑裂面上端点的应力边界状态和几何边界条件,对土压力变分计算方法进行了改进,使主动土压力的不确定问题变成了确定性问题。分析了填土内摩擦角、黏聚力、抗拉强度对开裂深度的影响,结果表明,随着内摩擦角和内聚力的增大,土体开裂深度逐渐增加,滑裂面向墙背方法偏移,土压力减小;随着土体抗拉强度的增加,开裂深度逐渐减小,土压力减小,当抗拉强度大到足以抵抗土体的开裂破坏,墙后土体开裂深度为0,这时土压力不再受抗拉强度的影响。 相似文献
8.
Numerical simulation of desiccation cracking in a thin clay layer using 3D discrete element modeling
Desiccation cracking of clay soil is of critical importance in many applications, such as industrial waste containment, hydraulic barriers, road embankments, and agricultural operations. The factors that influence cracking are known qualitatively, but it is not clear how to predict the initiation and propagation of cracks. This study presents a discrete element approach to modeling desiccation cracking in thin clay layers, considering material property changes. First, an aggregate shrinkage model based on the aggregate structure of clay was proposed, and the drying shrinkage of clay soil was modeled by imposing drying shrinkage kinetics for each aggregate at the micro-scale. Second, the clay soil was represented by an assembly of aggregates linked by bonds, and desiccation cracking of the clay layer was modeled using a three-dimensional discrete element code (PFC3D), with the aid of the embedded programming language FISH. When the clay layer is sufficiently thin, the water content gradient along the section can be neglected; thus, the shrinkage kinetics are the same for all of the grains of clay. In the model based on the discrete element method (DEM), the bond strength and contact stiffness changed during drying. Their changes were determined by matching the simulation results with the experimental data. Third, the DEM approach was validated by reproducing experimental desiccation tests performed on a thin clay layer in a disk shape. The geometric parameters of surface cracks were quantified using image analysis techniques and were compared with experimental observations. Fourth, some factors of influence, such as the sample thickness, the properties of the soil–base interface, micro-mechanical parameters, and shrinkage parameters, were investigated using the DEM model. The results obtained from the DEM analyses were compared with the results of prior research in this field of study. The approach used in this study is very promising for simulating desiccation cracking in thin clay soil because the model captures the initiation and propagation mechanism of desiccation cracks. Although this study was carried out on surface cracking in a thin clay layer, the extension of this methodology is of potential benefit not only for predicting three-dimensional desiccation cracking in real clay liners but also for modeling cracking in other materials with properties that vary with water content or temperature, such as concrete and rock. 相似文献
9.
Axi-symmetric Analysis of Geosynthetic-reinforced Granular Fill-soft Soil System with Group of Stone Columns 总被引：1，自引：1，他引：0
The paper presents a mechanical model to predict the behavior of geosynthetic-reinforced granular fill resting over soft soil
improved with group of stone columns subjected to circular or axi-symmetric loading. The saturated soft soil has been idealized
by spring-dashpot system. Pasternak shear layer and rough elastic membrane represent the granular fill and geosynthetic reinforcement
layer, respectively. The stone columns are idealized by stiffer springs. The nonlinear behavior of granular fill and soft
soil is considered. Consolidation of the soft soil due to inclusion of stone columns has also been included in the model.
The results obtained by using the present model when compared with the reported results obtained from laboratory model tests
shows very good agreement. The effectiveness of geosynthetic reinforcement to reduce the maximum and differential settlement
and transfer the stress from soft soil to stone columns is highlighted. It is observed that the reduction of settlement and
stress transfer process are greatly influenced by stiffness and spacing of the stone columns. It has been further observed
that for both geosynthetic-reinforced and unreinforced cases, the maximum settlement does not change if the ratio between
spacing and diameter of stone columns is greater than 4. 相似文献
10.
土体龟裂力学机理及理论模型研究进展 总被引：1，自引：0，他引：1
土体龟裂是一种常见的自然现象,它对土体的物理力学性质有重要影响,是许多工程地质及环境地质问题的重要诱因。开展土体龟裂研究,探讨其形成机理并构建相应的理论模型,一直是本课题的研究重点和难点。根据近年来国内外围绕土体龟裂所取得的研究成果,着重对土体龟裂的力学机理及相关理论模型研究进展进行了归纳和总结,并依据各模型的理论基础及其特点进行了分类和评价,得到如下主要认识:学界关于龟裂的形成机理尚未有统一认识,主流观点认为龟裂是土体张拉破坏的一种表现形式,张拉应力和抗拉强度是控制龟裂形成的两个关键力学指标,但上述力学机理不能解释所有的土体龟裂现象。与土体龟裂相关的理论模型总体上可以分为4大类:（1）以断裂力学为理论基础的模型:代表性的有线弹性断裂力学模型、弹塑性断裂力学模型和基于线弹性断裂力学的有限元模型;（2）以张拉破坏为理论基础的模型:代表性的有线弹性力学模型、剪切破坏模型、弹性力学模型和黏性开裂模型;（3）以土体干缩变形过程为基础的含水率-体积变化模型;（4）以土体固结理论为基础的应力路径分析模型。在此基础上,进一步对各模型的适用条件及不足之处进行了评价。最后,笔者对该课题今后的研究重点和方向提出了建议,包括:蒸发过程中土体微观结构变化及微观力学分析;蒸发过程中孔隙水的迁移过程、分布特征及赋存状态研究;土体收缩研究;土体抗拉强度研究;裂隙发育宽度及深度预测理论模型研究;龟裂发育几何形态特征预测理论模型研究。 相似文献
11.
In this paper, a numerical procedure based on the finite element method is outlined to investigate pile behaviour in sloping ground, which involves two main steps. First a free-field ground response analysis is carried out using an effective stress based stress path model to obtain the ground displacements, and the degraded soil stiffness and strength over the depth of the soil deposit. Next a dynamic analysis is carried out for the pile. The interaction coefficients and ultimate lateral pressure of soil at the pile–soil interface are calculated using degraded soil stiffness and strength due to build-up of pore pressures, and the soil in the far field is represented by the displacements calculated from the free-field ground response analysis. Pore pressure generation and liquefaction strength of the soil predicted by the stress path model used in the free-field ground response analysis are compared with a series of simple shear tests performed on loose sand with and without an initial static shear stress simulating sloping and level ground conditions, respectively. Also the numerical procedure utilised for the analysis of pile behaviour has been verified using centrifuge data, where soil liquefaction has been observed in laterally spreading sloping ground. It is demonstrated that the new method gives good estimate of pile behaviour, despite its relative simplicity. 相似文献
12.
In order to better understand opening-mode fracture initiation and propagation perpendicular to the bedding plane at depth in sedimentary rocks, a series of two-dimensional (2D) numerical simulations is conducted. First, the stress states between two adjacent fractures for a typical three-layer model with pre-assigned fractures are simulated. Second, the same three-layer model without pre-assigned fractures is adopted to study the initiation and propagation of fractures in layered rocks. Numerical results show that infilling fractures grow more easily from flaws located near the interface than from those in the middle of the fractured layer. Flaws can begin to propagate to form a complete infilling fracture when the size of the flaws exceeds half of the thickness of the central layer. Under different overburden stress conditions and internal fluid pressure, the numerically obtained ratio of the critical fracture spacing to layer thickness varies between 0.465 and 0.833. This range encompasses the often-cited ratios of spacing to layer thickness in the literature for well-developed fracture sets. In addition, both the fracture pattern and the critical value of the fracture spacing to layer thickness ratio are strongly dependent on the heterogeneous characteristics of the central layer. In cases with a relatively homogeneous central layer, more interface fractures occur, and the interface delamination evidently influences the fracture saturation. 相似文献
13.
Bearing capacity of two close strip footings on soft clay reinforced with geotextile 总被引：1，自引：1，他引：0
For many years ago, the beneficial effects of using reinforcement to improve the property of soil have been demonstrated. Over the last three decades, the use of polymeric reinforcement such as geotextile has increased in geotechnical engineering. Among the possible applications, earth reinforcement techniques have become useful and economical techniques to solve many problems in geotechnical engineering practice, such as improve the bearing capacity and settlement characteristics of the footing. This research presents the effect of geotextile inclusion on the bearing capacity of two close strip footings located at the surface of soft clay. A broad series of finite element analysis were performed on two footings with width of 1 and 2 m using two-dimensional plane strain model using the computer code Plaxis (ver 8). Only one type of soft clay was used for the analysis, and the soil was represented by two yielding criteria including hardening soil model and Mohr–Coulomb model, while reinforcement was represented by elastic element, and at the interface between the reinforcements and soft clay, interface elements have been used. A wide range of boundary conditions, including unreinforced and reinforced cases, was analyzed by varying parameters such as number of geotextile layers, vertical spacing of layers, depth to topmost layer of geotextile, tensile stiffness of geotextile layers, and distance of between two footings. From numerical results, the bearing capacity ratio and the interference factor of the foundations have been estimated. On the basis of the analysis performed in this research, it can be concluded that there is a best distance between footings and optimum depth for topmost layer to achieve maximum bearing capacity for closely spaced strip footings. The bearing capacity was also found to increase with increasing number of reinforcement layers if the reinforcements were placed within a range of effective depths. In addition, the analysis indicated that increasing reinforcement stiffness beyond a threshold value does not result in a further increase in the bearing capacity. 相似文献
14.
现浇混凝土薄壁管桩复合地基桩土应力比影响因素分析 总被引：3，自引：2，他引：1
桩土应力比是复合地基设计计算中一个重要参数。基于盐―通高速公路单桩复合地基静载试验,通过有限元模拟,研究了褥垫层模量和厚度、桩体模量、桩长、基础刚度等影响因素对现浇混凝土薄壁管桩复合地基桩土应力比的影响。结果表明所建立的模型是合理的。褥垫层模量增大或厚度减小导致桩土应力比增大,桩体模量、桩长和基础刚度的增加可使桩土应力比增加。 相似文献
15.
在干燥环境中,由于蒸发失水,膨胀土发生收缩,表面容易产生纵横交错的裂隙网络(龟裂)。龟裂的产生会极大弱化土体的工程性质,并导致各种工程问题。随着极端干旱气候的频发,膨胀土龟裂问题将会越来越多,越来越显著。开展龟裂研究对揭示龟裂现象的本质规律和指导膨胀土地区的工程实践有重要意义。龟裂的形成和发展是一个动态的过程,与土中水分的蒸发速率、应力状态、收缩特性等直接相关:龟裂形成时水分蒸发处于常速率阶段; 吸力和抗拉强度是制约龟裂形成的两个关键力学参数,当土体中的吸力引起的张拉应力超过土体的抗拉强度时,龟裂便会产生; 龟裂是孔隙发生收缩的直观表现。总体上,力的作用和收缩空间是土体龟裂形成的两个必要条件。此外,膨胀土龟裂具有非常复杂的发生发展过程,受土质学、土力学、土结构、试验条件和方法等许多因素的影响。龟裂定量分析是龟裂研究的重要内容之一,能为龟裂机理研究及相关理论模型的建立提供必要参数。计算机图形处理技术具有效率高、操作性强、精度高等优点,为龟裂定量分析提供了强有力的工具。目前关于土体龟裂研究还存在许多不足之处,在今后的工作中,应该重视龟裂形成和发展过程的动态特征,围绕与土体龟裂相关的水-土作用关系、力学机制、收缩变形机制、大尺度现场试验和三维观测分析技术等方面开展更多的针对性研究,综合考虑龟裂形成过程中的土质学、土力学和土结构因素,结合宏观现象与微观分析,建立土体龟裂的理论体系。 相似文献
16.
The ability to model and predict the formation of desiccation cracks is potentially beneficial in many applications such as clay liner design, earth dam construction, and crop science, etc. However, most studies have focused on statistical analysis of crack patterns and qualitative study of contributing factors to crack development rather than prediction. Because it is exceedingly difficult to capture the nonlinear processes during desiccation in analytical modelling, most such models handle crack formation without considering variation of material properties with time, and are unattractive to use in realistic modelling. The data obtained from laboratory experiments on clay soil desiccating in moulds were used as a basis to develop a more refined model of desiccation cracking. In this study, the properties, such as matric suction, stiffness and tensile strength of soil, and base adhesion, could be expressed approximately as functions of moisture content. The initial conditions and the development of suction due to desiccation and the varying material properties were inputted to UDEC, a distinct element code, using its internal programming language FISH. The model was able to capture some essential physical aspects of crack evolution in soil contained in moulds with varying lengths, heights, and materials of construction. Extension of this methodology is potentially beneficial not only for modelling desiccation cracking in clay, but also in other systems with evolving material properties such as concrete structures and road pavements. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
17.
Stone columns are found to be effective and economical ground improvement technique in soft grounds. Understanding its behaviour
when they are installed in stratified soils, in particular when the upper layer consists of weak soil, will be of great practical
significance. This paper presents results from a series of laboratory plate load tests carried out in unit cell tanks to investigate
the behaviour of stone columns in layered soils, consisting of weak soft clay overlying a relatively stronger silty soil,
for various thicknesses of the top layer. Tests were carried out with two types of loading (1) the entire area in the unit
cell tank loaded, to estimate the stiffness of improved ground and (2) only the stone column loaded, to estimate the limiting
axial capacity. Laboratory tests were carried out on a column of 90 mm diameter surrounded by layered soil, for an area ratio
of 15%. It is found that the depth of top weak layer thickness has a significant influence on the stiffness, load bearing
capacity and bulging behavior of stone columns. 相似文献
18.
A Calculation Model for Corrosion Cracking in RC Structures 总被引：5，自引：0，他引：5
A novel calculation model is proposed aiming at the problem of concrete cover cracking induced by reinforcement corrosion. In this article, the relationship between the corrosion depth of the bar and the thickness of the rust layer is established. By deducing the radial displacement expression of concrete, the formula for corrosion depth and corrosion pressure before cracking is proposed. The crack depth of cover in accordance with the maximum corrosion pressure is deduced; furthermore, the corrosion depth and corrosion pressure at the cracking time are obtained. Finally, the theoretical model is validated by several experiments, and the calculated values agree well with the experiment results. 相似文献
19.
三明治形加筋土是一种在黏土中加入加筋砂层形成的混合填料形式的新型加筋土。为了研究不同条件下三明治形加筋土筋-土界面的动力剪切特性,采用大型直剪仪对三明治形加筋土进行了一系列循环剪切试验,研究了不同薄砂层厚度、循环剪切幅值和竖向应力对界面剪切特性的影响。试验结果表明：筋-土界面的剪应力峰值随着循环次数的增加而增加,循环周次为10时,薄砂层厚度为5、6、7、8、9 mm的条件下,筋-土界面的剪应力峰值分别为24.84、27.4、27.94、26.33、24.68 kPa,表明薄砂层厚度为7 mm时,筋-土界面在循环剪切阶段的峰值剪应力最大;剪切幅值越大,界面循环剪切的最终剪缩量越大,同一循环次数对应的剪切刚度和阻尼比越小;在不同竖向应力下,界面在循环剪切过程中都发生了循环剪切硬化现象,循环周次为10时,竖向应力为30、60、90 kPa的条件下,筋-土界面的剪应力峰值分别为20.4、25.14、32.96 kPa,表明剪应力峰值随竖向应力的增大而增大,同一循环次数对应的剪切刚度也随竖向应力的增大而增大。 相似文献
20.
为研究液化场地中群桩在强震作用下的动力响应特征及桩侧土抗力-桩土相对位移（p-y）曲线规律,依托海文大桥实体工程,基于振动台模型试验,开展了0.15g～0.35g地震动作用饱和粉细砂土层不同埋置深度下的砂土孔压比、桩身弯矩及p-y曲线动力响应研究。结果表明：地震动强度达到0.25g时,不同埋置深度下的饱和粉细砂土层孔压比均大于0.8,产生液化现象,且随埋置深度增加,孔压比增长时刻明显滞后;不同埋置深度下,桩身弯矩最大值均位于液化土层和非液化土层分界面处;同一埋置深度时,随地震动强度的增大,p-y曲线所包围的面积逐渐增大,其整体斜率逐渐变小,说明桩-土相互作用动力耗能逐渐增大,桩周土体刚度逐渐减小;随埋置深度增加,p-y曲线所包围的面积逐渐减小,其整体斜率逐渐增大,说明桩-土相互作用动力耗能逐渐减小,桩周土体刚度逐渐增大。因此,液化场地桥梁群桩抗震设计时,应综合考虑液化土层与桩基础的相互位置关系,确保桩基础在液化土层与非液化土层分界处的抗弯承载能力。 相似文献