共查询到20条相似文献，搜索用时 31 毫秒
1.
沉积盆地沉积物天然水力压裂理论及意义 总被引：5，自引：3，他引：5
在阐明沉积盆地沉积物天然水力压裂机制后，重点讨论了天然水力压裂及幕式排液和意义，以断裂力学的理论和方法分析了压力仓封闭层的破裂问题，并以北海盆地及松辽盆地为例，重点阐述了天然水力断裂系统的特征，规模及意义，明确指出这种断裂系统将对沉积 构造解释及油气勘探具有重要的影响。 相似文献
2.
Yongquan Hu Zhiqiang Li Jinzhou Zhao Zhengwu Tao Pan Gao 《Environmental Earth Sciences》2017,76(15):546
The ultra-low-permeability shale gas reservoir has a lot of well-developed natural fractures. It has been proven that hydraulic fracture growth pattern is usually a complex network fracture rather than conventional single planar fractures by micro-seismic monitoring, which can be explained as the shear and tensile failure of natural fractures or creation of new cracks due to the increase in reservoir pore pressure caused by fluid injection during the process of hydraulic fracturing. In order to simulate the network fracture growth, a mathematical model was established based on full tensor permeability, continuum method and fluid mass conservation equation. Firstly, the governing equation of fluid diffusivity based on permeability tensor was solved to obtain the reservoir pressure distribution. Then Mohr–Coulomb shear failure criterion and tensile failure criterion were used to decide whether the rock failed or not in any block on the basis of the calculated reservoir pressure. The grid-block permeability was modified according to the change of fracture aperture once any type of rock failure criterion was met within a grid block. Finally, the stimulated reservoir volume (SRV) zone was represented by an enhancement permeability zone. After calibrating the numerical solution of the model with the field micro-seismic information, a sensitivity study was performed to analyze the effects of some factors including initial reservoir pressure, injection fluid volume, natural fracture azimuth angle and horizontal stress difference on the SRV (shape, size, bandwidth and length). The results show that the SRV size increases with the increasing initial pore reservoir and injection fluid volume, but decreases with the increase in the horizontal principal stress difference and natural fracture azimuth angle. The SRV shape is always similar for different initial pore reservoir and injection fluid volume. The SRV is observed to become shorter in length and wider in bandwidth with the decrease in natural fracture azimuth angle and horizontal principal stress difference. 相似文献
3.
储层岩体中的天然结构面对水力压裂缝网改造具有重要的影响。本文采用真实破裂过程分析软件RFPA2D-Flow,在考虑岩体非均质性和岩体渗流-应力-损伤破裂特性的基础上,对不同尺度天然结构面影响的水力压裂裂缝扩展与演化行为进行了模拟分析和讨论,研究结果表明:（1）当水力裂缝遇天然非闭合裂隙时,在水力裂缝靠近非闭合裂隙区间形成拉张应力区,水力裂缝与区间非闭合裂隙间微元体累进性张拉破坏是导致水力裂缝与非闭合裂隙贯通的主要机制;（2）层理等优势结构对水力压裂裂缝扩展及缝网形态影响十分显著,当最大主应力方向与层理面走向小角度相交时,层理结构面对水力裂隙的扩展起主要作用,当最大主应力方向与层理面走向大角度相交时,最大主压应力与层理面共同对缝网扩展起主导作用,随着优势结构面的增多和差应力的增大,水力压裂形成的缝网范围和复杂性程度随之增大;（3）储层水力压裂是一种局部范围内的短暂动力扰动过程,尽管断层的存在可以极大地影响水力裂缝的扩展模式,增大水力裂隙扩展高度,但相比于储层埋深,水力压裂对断层封闭性的破坏范围和断层活动性的扰动程度十分有限。 相似文献
4.
Two-dimensional hydraulic fracturing simulations using the cohesive zone model (CZM) can be readily found in the literature; however, to our knowledge, verified 3D cohesive zone modeling is not available. We present the development of a 3D fully coupled hydro-mechanical finite element method (FEM) model (with parallel computation framework) and its application to hydraulic fracturing. A special zero-thickness interface element based on the CZM is developed for modeling fracture propagation and fluid flow. A local traction-separation law with strain softening is used to capture tensile cracking. The model is verified by considering penny-shaped hydraulic fracture and plain strain Kristianovich‑Geertsma‑de Klerk hydraulic fracture (in 3D) in the viscosity- and toughness-dominated regimes. Good agreement between numerical results and analytical solutions has been achieved. The model is used to investigate the influence of rock and fluid properties on hydraulic fracturing. Lower stiffness tip cohesive elements tend to yield a larger elastic deformation around the fracture tips before the tensile strength is reached, generating a larger fracture length and lower fracture pressure compared with higher stiffness elements. It is found that the energy release rate has almost no influence on hydraulic fracturing in the viscosity-dominated regime because the energy spent in creating new fractures is too small when compared with the total input energy. For the toughness-dominated regime, the released energy during fracturing should be accurately captured; relatively large tensile strength should be used in order to match numerical results to the asymptotic analytical solutions. It requires smaller elements when compared with those used in the viscosity-dominated regime. 相似文献
5.
Liao Jianxing Gou Yang Feng Wentao Mehmood Faisal Xie Yachen Hou Zhengmeng 《Acta Geotechnica》2020,15(2):279-295
Although hydraulic fracturing has been massively studied and applied as a key technique to enhance the gas production from tight formations, some problems and uncertainties exist to accurately predict and analyze the fracture behavior in complex reservoirs, especially in the naturally fractured reservoirs like shale reservoirs. This paper presents a full 3D numerical model (FLAC3D) to study hydraulic fracturing behavior under the impact of preexisting orthogonal natural fractures. In this numerical model, the hydraulic fracture propagation direction is assumed perpendicular to the minimum principal stress and activated only by tensile failure, whereas the preexisting natural fractures can be activated by tensile or shear failure or a combination of them, and only tensile failure can open the natural fracture as well. The newly developed model was used to study the impact of preexisting orthogonal natural fractures on hydraulic fracturing behavior, based on a multistage hydraulic fracturing operation in a naturally fractured reservoir from the Barnett Shale formation, northwest of Texas in USA. In this multistage operation, two more representative stages, i.e., stage 1 with a relatively large horizontal stress anisotropy of 3.3 MPa and stage 4 with a comparatively small one of 1.3 MPa, were selected to conduct the simulation. Based on the numerical results, one can observe that the interaction between hydraulic and natural fracture is driven mainly by induced stress around fracture tip. Besides, the horizontal stress anisotropy plays a key role in opening the natural fracture. Thus, no significant opened fracture is activated on natural fracture in stage 1, while in stage 4 an opened fracture invades to about 90 m into the first natural fracture. Conversely, the hydraulic fracture length in stage 1 is much longer than in stage 4, as some fluid volume is stored in the opened natural fracture in stage 4. In this work, the shear failure on natural fractures is treated as the main factor for inducing the seismic events. And the simulated seismic events, i.e., shear failure on natural fractures, are very comparable with the measured seismic events.
相似文献6.
水平井中多条水力裂缝间的应力干扰行为,造成了压裂液排量的非均匀分配,影响了水力裂缝的几何形态。采用边界元法研究岩体在压裂液作用下的变形程度,以幂律流体泊肃叶平板流动方程来研究水力裂缝内部的压裂液流场,考虑了多条裂缝间应力干扰和压裂液流量分配,建立了流-固耦合的水平井多条水力裂缝同步扩展模型。模型可模拟水平井多条水力裂缝几何形态、应力干扰情况和压裂液排量的分配情况,可解释水力裂缝之间的竞争机制。多条裂缝同步扩展时,压裂液排量并非均等地分配到各个裂缝之中,进入到内部裂缝的压裂液流量最小,内部裂缝宽度最小;内部的水力裂缝增长一定长度后,停止增长,并且在应力干扰下逐渐闭合。 相似文献
7.
为了揭示水压致裂法和巴西劈裂法测量岩石抗拉强度的关系,开展了理论和现场试验研究。基于经典的水压致裂法理论,推导了不同围压下钻孔破裂压力和抗拉强度。利用断裂力学理论建立了水压致裂法和巴西劈裂法测得抗拉强度的关系。利用预制切槽方法模拟天然裂纹,对水力裂缝的起裂压力进行了研究。结果表明：围压为最大主应力等于3倍最小主应力测得的抗拉强度大于围压为0测得的抗拉强度;水压致裂法和巴西劈裂法测量抗拉强度关系与应力场、裂纹长度、断裂韧度3个变量有关;通过在晋城矿区王台铺矿的预制切槽试验,运用断裂力学建立的抗拉强度计算式更为符合现场实际。研究结果可为坚硬难垮落顶板预制切槽的水力压裂设计提供参考。 相似文献
8.
页岩储层孔隙度和渗透率极低,天然裂缝和水平层理发育,常规压裂增产措施无法满足页岩气的开发要求,水平井多段分簇压裂是页岩气开发的关键技术之一,该技术能够大幅度提升压裂改造的体积、产气量和最终采收率。为确定页岩储层水平井多段分簇射孔压裂的起裂点和起裂压力,采用有限元方法建立了水平井套管完井（考虑水泥环和套管的存在）多段分簇射孔的全三维起裂模型。数值模型的起裂压力与室内试验结果吻合较好,证明了数值模型的准确性和可靠性。利用数值模型研究了页岩水平井多段分簇射孔压裂的起裂点和起裂压力的影响因素,研究发现：射孔孔眼附近无天然裂缝或水平层理影响,起裂点发生在射孔簇孔眼的根部;射孔簇间距越小,中间射孔簇的干扰越大,可能造成中间的射孔簇无法起裂;射孔密度和孔眼长度增大,起裂压力降低;天然裂缝的存在,在某些情况能够降低起裂压力且改变起裂位置,主要与天然裂缝的分布方位及水平主应力差有关;水平层理可能会降低起裂压力,但与垂向主应力与水平最小主应力的差值有关。获得的起裂压力变化规律,可作为进一步研究水平井多段分簇射孔条件下的裂缝扩展规律的基础,可以为压裂设计和施工的射孔参数确定及优化给出具体建议。 相似文献
9.
随着扩展有限元理论的深入研究,利用扩展有限元方法模拟水力压裂具有了一定的可操作性。相比于常规有限元方法,XFEM方法具有计算结果精度高和计算量小的优点。但是,如何模拟射孔孔眼、如何模拟流体与岩石相互作用以及分析水力裂缝的扩展规律仍然是难题。以研究水力压裂裂缝扩展规律为目的,建立了岩石多孔介质应力平衡方程、流体渗流连续性方程和边界条件。通过有限元离散化方法对耦合方程矩阵进行处理。通过富集函数定义初始裂缝（射孔孔眼）,选择最大主应力及损伤变量D分别作为裂缝起裂和扩展判定准则,利用水平集方法模拟水力裂缝扩展过程。数值模拟结果显示：增加射孔方位角、压裂液排量和减小水平地应力差,起裂压力上升;黏度对起裂压力无明显影响。增加射孔方位角、压裂液排量、黏度和减小水平地应力差值有助于裂缝宽度的增加。增加水平地应力差值、压裂液排量和减小射孔方位角以及压裂液黏度有助于裂缝长度增加,反之亦然。基于ABAQUS的水力裂缝扩展有限元法可对不同井型和诸多储层物性参数及压裂施工参数进行分析,且裂缝形态逼真,裂缝面凹凸程度清晰,结果准确。此研究可作为一种简便有效研究水力压裂裂缝扩展规律的方法为油田水力压裂设计与施工提供参考与依据。 相似文献
10.
针对高角度天然裂缝发育地层中的水平井水力压裂问题,开展了水力裂缝自天然裂缝处起裂扩展的理论和试验研究。尝试将天然裂缝简化为与井筒轴线垂直的横向裂缝,基于线弹性断裂力学理论和最大拉应力准则,给出了水力裂缝起裂压力和扩展过程中应力强度因子的计算方法。利用预制横缝模拟高角度天然裂缝,开展了室内水力压裂试验,对水力裂缝的扩展形态和起裂压力进行了研究。理论计算表明,（1）水力裂缝自预制横缝端部起裂后,扩展距离超过1倍的预制横缝端部半径时可将预制横缝和水力裂缝合并起来,整体视作一条横向裂缝来计算应力强度因子;（2）水力裂缝尖端距井壁处的距离大于4倍的井筒半径时,应力强度因子的计算可忽略井筒的影响,近似采用硬币形裂缝的计算公式。试验研究发现,（1）水力裂缝在预制横缝端部起裂并扩展,形成与井筒轴线垂直的横向裂缝,裂缝的扩展呈现出Ⅰ型断裂的特点,形态近似呈圆形,未发现与井筒轴线平行的纵向裂缝的起裂和扩展;（2）排量对破裂净压力和起裂净压力有重要影响,大排量会导致较高的破裂净压力和起裂净压力,在大、小两种排量下起裂净压力的离散性均较小,计算得到的KⅠ临界断裂值的离散性也较小。研究结果可为改善裂缝发育储层的近井裂缝形态提供指导,也可为煤矿开采中预制横向切槽的水力压裂设计提供参考。 相似文献
11.
12.
超临界CO2是一种介于气体和液体之间的特殊状态的CO2流体,具有低黏、高扩散性和零表面张力等独特的性质。利用超临界CO2作为压裂液,有助于裂缝的起裂和扩展,同时可避免储层伤害。通过研究超临界CO2射流破岩和压裂特性,分析得到了超临界CO2岩石致裂机制。研究结果表明,超临界CO2低黏等特性使其更容易进入岩石微孔和微缝之中,在岩石内部建立大小不一的流体压力系统,使岩石发生拉伸和剪切破坏;常规流体压裂起裂压力较高,裂缝一般为单条或多条平直裂缝,大多沿着同一方向贯穿强度较高的胶结颗粒,且裂缝断面光滑、平整;超临界CO2压裂起裂压力相比于常规流体压裂低,在岩石中形成的裂缝网络较为复杂,裂缝互相连通,一般沿着强度较低的胶结物开裂,较少贯穿胶结颗粒,裂缝断面较为粗糙。该研究结果可为超临界CO2压裂技术的实施提供理论支撑。 相似文献
13.
Gas production from shale formations by hydraulic fracturing has raised concerns about the effects on the quality of fresh groundwater. The migration of injected fracking fluids towards the surface was investigated in the North German Basin, based on the known standard lithology. This included cases with natural preferential pathways such as permeable fault zones and fracture networks. Conservative assumptions were applied in the simulation of flow and mass transport triggered by a high pressure boundary of up to 50 MPa excess pressure. The results show no significant fluid migration for a case with undisturbed cap rocks and a maximum of 41 m vertical transport within a permeable fault zone during the pressurization. Open fractures, if present, strongly control the flow field and migration; here vertical transport of fracking fluids reaches up to 200 m during hydraulic fracturing simulation. Long-term transport of the injected water was simulated for 300 years. The fracking fluid rises vertically within the fault zone up to 485 m due to buoyancy. Progressively, it is transported horizontally into sandstone layers, following the natural groundwater flow direction. In the long-term, the injected fluids are diluted to minor concentrations. Despite the presence of permeable pathways, the injected fracking fluids in the reported model did not reach near-surface aquifers, either during the hydraulic fracturing or in the long term. Therefore, the probability of impacts on shallow groundwater by the rise of fracking fluids from a deep shale-gas formation through the geological underground to the surface is small. 相似文献
14.
In this study, the effects of the temperature difference between hydraulic fracturing fluid and rock formation on the time‐dependent evolution of fracture width were investigated using a newly derived one‐dimensional anisotropic porothermoelastic analytical solution. The solution is shown to correctly reproduce existing solutions for special cases and corrections for an earlier publication are provided. An analysis of time‐dependent fracture width evolution using Woodford Shale data was also presented. It was found that when the fracturing fluid has the same temperature as the shale formation, the fracture gradually closes back after the initial opening due to the invasion of the fracturing fluid. Practically, in this scenario, proppants should be pumped into the fracture as soon as possible to obtain maximum fracture conductivity. On the other hand, with a fracturing fluid 60 °C colder than the formation, the thermal contraction of the rock dominates the fracture aperture evolution, resulting in a fracture aperture approximately 70% larger than that produced by the hotter fracturing fluid. Consequently, in this case, it is beneficial to delay proppant placement to take advantage of the widening fractures. Finally, it was found that the fracture aperture is directly controlled by the spacing of natural fractures. Therefore, the presence of natural fractures in the shale formation and their spacing influence not only the type of hydraulic fractures created but also what kind and size of proppants should be used to keep them open. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
15.
水压致裂后煤岩应力分布规律对水压致裂防冲效果起关键性作用。采用理论研究方法得出高压注水压致裂后及卸水后水区和气区的孔隙、瓦斯压力和煤体应力解析解。结果表明,致裂后水区孔隙压力沿径向变化不大,与注水压力接近;气区瓦斯压力沿径向呈递减趋势;在水区外围一定范围内形成瓦斯压力升高区;水区煤体环向应力将会减小,直到变为拉应力;气区煤体径向应力沿径向递减。卸水后水区孔隙压力、煤体径向应力沿径向呈递增趋势;气区煤体径向应力沿径向呈递增趋势,趋近于原始煤体应力;气区煤体环向应力沿径向呈递减趋势;气区孔隙压力沿径向呈递减趋势。这为煤层水压致裂预防冲击地压提供理论基础。 相似文献
16.
The hydraulic fracturing technique has been widely applied in many fields, such as the enhanced geothermal systems (EGS), the improvement of injection rates for geologic sequestration of CO2, and for the stimulations of oil and gas reservoirs. The key points for the success of hydraulic fracturing operations in unconventional resources are to accurately estimate the redistribution of pore pressure and stresses around the induced fracture and predict the reactivations of preexisting natural fractures. The pore pressure and stress regime around hydraulic fracture are affected by poroelastic and thermoelastic phenomena as well as by fracture opening compression. In this work, a comprehensive semi-analytical model is used to estimate the stress and pore pressure distribution around an injection-induced fracture from a single well in an infinite reservoir. The model allows the leak-off distribution in the formation to be three-dimensional with the pressure transient moving ellipsoidically outward into the reservoir from the fracture surface. The pore pressure and the stress changes in three dimensions at any point around the fracture caused by poroelasticity, thermoelasticity, and fracture compression are investigated. With Mohr-Coulomb failure criterion, we calculate the natural fracture reactivations in the reservoir. Then, two case studies of constant water injection into a hydraulic fracture are presented. This work is of interest in the interpretation of microseismicity in hydraulic fracturing and in the estimation of the fracture spacing for hydraulic fracturing operations. In addition, the results from this study can be very helpful for the selection of stimulated wells and further design of the refracturing operations. 相似文献
17.
水力压裂扩展特性的数值模拟研究 总被引：7，自引：0，他引：7
采用ABAQUS建立了水力压裂计算模型,模拟了地应力、岩石力学特性、压裂液流体特性等各种复杂因素对水力压裂扩展的影响。通过计算分析得到一些有益结论：（1）在注入压力一定的情况下起裂压力与最小水平地应力、临界应力、初始孔隙压力成正比,而与压裂液黏度、最大水平地应力、弹性模量无关;（2）裂缝扩展长度和最大缝宽与最小水平地应力、初始孔隙压力、弹性模量成反比,而与最大水平地应力无关;（3）水力压裂作业中,缝长的扩展过程可分为无扩展阶段、快速扩展阶段、稳定扩展阶段以及缓慢扩展阶段等4个阶段。研究结论对于水力压裂作业优化具有参考价值。 相似文献
18.
干热岩水压致裂过程中低温诱导热应力与注入水压共同影响裂缝的萌生与扩展。首先通过THM耦合分析了低温压裂液注入过程中注入水压与热应力的相互作用及其对裂缝萌生的影响,随后建立描述岩石细观结构的THMD耦合模型对热应力影响下高温岩石水压致裂过程进行初探。结果表明：低温压裂液注入高温岩石产生的热应力包括岩石自身温度梯度形成的热应力与岩石颗粒非均匀膨胀导致的热应力,并在井筒周围呈现为拉应力。高注入压力将抑制热应力导致的多裂缝萌生,井筒附近热应力的存在对注入压力也具有削弱作用。基岩温度升高,裂缝萌生阶段更多裂缝在井筒附近起裂,缝网沿最大地应力方向的扩展速度减慢,但改造规模增加,同时多裂缝的存在也使得裂缝延伸压力增加。 相似文献
19.
Modeling hydraulic fracturing in the presence of a natural fracture network is a challenging task, owing to the complex interactions between fluid, rock matrix, and rock interfaces, as well as the interactions between propagating fractures and existing natural interfaces. Understanding these complex interactions through numerical modeling is critical to the design of optimum stimulation strategies. In this paper, we present an explicitly integrated, fully coupled discrete‐finite element approach for the simulation of hydraulic fracturing in arbitrary fracture networks. The individual physical processes involved in hydraulic fracturing are identified and addressed as separate modules: a finite element approach for geomechanics in the rock matrix, a finite volume approach for resolving hydrodynamics, a geomechanical joint model for interfacial resolution, and an adaptive remeshing module. The model is verified against the Khristianovich–Geertsma–DeKlerk closed‐form solution for the propagation of a single hydraulic fracture and validated against laboratory testing results on the interaction between a propagating hydraulic fracture and an existing fracture. Preliminary results of simulating hydraulic fracturing in a natural fracture system consisting of multiple fractures are also presented. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
20.
The production efficiency of shale gas is affected by the interaction between hydraulic and natural fractures. This study presents a simulation of natural fractures in shale reservoirs, based on a discrete fracture network (DFN) method for hydraulic fracturing engineering. Fracture properties of the model are calculated from core fracture data, according to statistical mathematical analysis. The calculation results make full use of the quantitative information of core fracture orientation, density, opening and length, which constitute the direct and extensive data of mining engineering. The reliability and applicability of the model are analyzed with regard to model size and density, a calculation method for dominant size and density being proposed. Then, finite element analysis is applied to a hydraulic fracturing numerical simulation of a shale fractured reservoir in southeastern Chongqing. The hydraulic pressure distribution, fracture propagation, acoustic emission information and in situ stress changes during fracturing are analyzed. The results show the application of fracture statistics in fracture modeling and the influence of fracture distribution on hydraulic fracturing engineering. The present analysis may provide a reference for shale gas exploitation. 相似文献