共查询到18条相似文献，搜索用时 0 毫秒
1.
在研究节理的渗流时,渗流控制方程对节理渗流分析结果具有显著影响。首先介绍了节理渗流分析中的控制方程：Navier-Stokes方程、Stokes方程、Reynolds方程和立定定理,并分析了各控制方程在节理渗流分析中的适用性。以Reynolds方程作为渗流分析控制方程,建立了粗糙节理渗流空腔模型。然后以节理试件为研究对象,在实测节理三维表面形貌并计算隙宽分布后,分别进行相同渗流边界条件下的室内渗流试验和空腔模型计算,得到节理在不同接触状态下的渗流量实测值和计算值,并分别将计算结果与立方定理下的空腔模型、将整个节理简化为光滑平行板模型的立方定理以及速宝玉经验公式的计算结果进行比较,结果表明,Reynolds方程下的节理渗流空腔模型计算结果与实测值最为吻合,可以较为准确地反映节理的渗流情况。同时,根据Reynolds方程下空腔模型得到的渗流流量分布可以呈现节理渗流的曲折现象,为从本质上研究节理渗流特性奠定了理论基础。 相似文献
2.
节理岩体渗流-应力耦合特性研究是岩石力学领域的重点和难点。水利水电工程与地下工程中天然节理岩体往往处于三向不等压应力状态,针对三向应力状态下节理岩体渗流-应力耦合特性研究较少。其中,单节理岩体渗流-应力耦合特性研究是基础。首先分析与探究了单节理岩体侧向应力作用效果及渗流作用机制,在单节理岩体渗透性-应力耦合分析模型基础上推导了单节理岩体渗流-应力耦合的理论公式。通过室内真三轴渗流-应力耦合试验,基于全局优化算法的非线性拟合及块体离散元数值仿真,验证了所提出理论公式的合理性。基于电路原理,给出了模拟电路与渗流问题的相似物理量,通过引入等效渗流阻方法,探究了典型的含正六边形主干节理网络的渗流-应力耦合特性。该研究结果对实际工程岩体的渗流分析有一定的参考价值。 相似文献
3.
节理中接触面积的存在使得渗流曲折效应更加明显,将对渗流产生显著影响。为了研究节理接触面积对节理渗流的影响,建立节理渗流概念模型,推导得到了节理渗流的接触面积影响系数;然后在节理渗流计算公式中引入该影响系数,得到了考虑接触面积影响的渗流计算公式。同时,由于接触面积的存在使得渗流曲折因子的计算更为复杂,在获得节理隙宽分布的基础上提出了计算节理渗流曲折因子的五点比较法。然后以人工大理岩节理试件为研究对象,在获得其三维表面形貌的基础上,一方面对其进行不同接触状态下5级法向应力作用下的渗流试验;另一方面,在根据节理试件的三维表面形貌数据计算节理的渗流平均曲折因子和接触面积比的基础上,分别采用考虑接触面积影响的渗流计算公式和Zimmerman计算公式对节理试件在不同法向应力作用下的渗流体积流量进行计算,并将计算结果与实测值进行比较。结果表明：考虑接触面积影响的渗流计算公式计算结果与实测值吻合较好,从而验证了考虑接触面积影响的渗流计算公式的正确性,而Zimmerman计算公式高估了节理的渗流流量。 相似文献
4.
5.
深部断续节理岩体中渗流对巷道稳定性影响的数值分析 总被引：1，自引：0，他引：1
应用自主开发的岩石破坏过程渗流与应力耦合分析软件F-RFPA2D,通过对高应力节理岩体中巷道的失稳破坏过程所进行的数值模拟分析,研究了深部断续节理岩体中地应力及渗流对巷道稳定性的影响。模拟结果不但直观形象地给出了巷道的渗流场、应力场、破坏区分布,而且得到了巷道周边关键部位的位移变化情况,并与无地下水的稳定性进行了比较。结果表明,岩体中断续节理与地应力及渗流相互作用,对巷道失稳的演化起了重要作用,如巷道与节理的相对方位决定了巷道坍塌的方向;岩桥对巷道的稳定起了重要的作用;虽然渗流应力加速了巷道的失稳破坏,但没有改变高地应力对巷道的主要破坏模式。该研究对于进一步理解深部岩体中节理、地应力及渗流对巷道稳定性的影响进而采取有效的加固措施具有重要的理论和实践意义 相似文献
6.
渗透水压对节理应力-渗流耦合特性的影响试验研究 总被引：1，自引：0，他引：1
为研究渗透水压对节理应力-渗流耦合特性的影响,通过对6组人造节理试件恒定法向载荷和恒定法向刚度的压剪渗流试验,分析了应力和位移、节理水力开度以及透过率随剪切位移的变化趋势,获得了渗透水压对节理岩石应力-渗流耦合特性的影响规律。结果表明：节理试件的剪切应力和位移、水力开度以及透过率都与渗透水压密切相关。剪切应力随渗透水压的增大而减小,法向变形、水力开度和透过率却随渗透水压的增大而增大。在压剪渗流试验过程中,不同渗透压力的节理试件都发生了剪胀效应。研究可为深部岩体工程围岩遇水作用稳定性及渗流灾害控制技术提供科学的理论依据。 相似文献
7.
节理岩体几何结构非常复杂,研究其渗流特性对于指导含水岩层稳定性分析具有重要价值。应用离散裂隙网络模型DFN方法,基于VC++6.0软件平台,建立了平面渗流分析方法,分析了节理岩体不同几何分布情况下的渗透率张量特征,通过定义渗流定向性系数对岩体渗流的定向性特征进行了定量分析。结果表明：单组节理岩体渗流具有明显的各向异性特征,渗流定向性随着节理角度变化显著;节理随着节理贯通性增加,节理渗透率呈现对数增加趋势;两组节理情况下,各向异性特征随着节理组间夹角变化;两组节理岩体渗流特征研究中,正交分布下,岩体仍存在各向异性,但渗流定向性系数较低;当节理倾角服从正态分布时,随着节理倾角标准差增大,渗透率增加;两组节理夹角不同时,节理渗透主方向倾角随着夹角增大而相应增大,基本沿两组节理夹角方向的角平分线方向。 相似文献
8.
岩石节理的渗流广义立方定理 总被引：29，自引：5，他引：29
首先讨论了岩石节理的渗流立方定理及其适用条件，然后从渗流与变形耦合的角度，论述了节理的开度性质，并提出了适用于一般节理的渗流广义立方定理，最后用有限元数值模拟方法验证了广义立方定理。 相似文献
9.
10.
节理、裂隙控制着地表岩体的力学强度和导水特性。采用遍布节理力学模型和饱和非饱和等效连续介质渗流模型反映节理的主导作用,基于节理连通率将岩体的渗流特性与力学特性耦合起来,分析了在FLAC3D中实现渗流与力学耦合机制、降雨边界条件处理以及连通率演化,并开发了适用于FLAC3D的多组遍布节理模型,模拟了海南矿业联合有限公司一顺层平台边坡降雨过程中渗流场和力学场的变化。计算结果表明,降雨开始后边坡地表迅速饱和并形成暂态饱和区,随着降雨的继续,边坡负压区进一步缩小,同时暂态饱和区也不断扩大;在降雨结束后,由于水压力迅速消散造成暂态饱和区开始减小,在降雨过程中渗流也会引起层面的破坏和其裂隙连通率的演化。因此,运用上述耦合分析模型计算降雨入渗对边坡稳定性的影响是可行的。 相似文献
11.
12.
A new experimental system composed of two devices is presented for studying the hydraulic conductivity of rock joints and other interfaces in relation with their mechanical loading. This system allows for investigations on the anisotropy of the hydraulic conductivity, as well as for its heterogeneity. The first device controls the injection of a fluid, regulated in pressure or discharge near the centre of the sample of rock joint, which produces a quasi‐radial flow within the joint. The output flow is measured in real time using a sectorized peripheral membrane for acquisition of data about the directionality or anisotropy of the flow. The second device allows for the measurement of the evolution of the morphology and of the void map of the rock joints during their mechanical loading (compression or shearing). It is a laser beam moved by an (x, y) frame. This frame is installed within the shear box at several stages of the loading, after temporarily moving one rock wall away from the other one, but without unmounting them from the shear box. After the presentation of the experimental system, and of its performances, we give some examples of test results of replicas of rock joints, loaded in compression and shearing. First, these results show that the change in global transmissivity of the samples is strongly correlated with the normal relative displacement of the rock walls. Several statistical analyses of the change in the void map, taking into account the damage of the asperities of the joint, are presented and compared with the results of the directional output flows. Today further studies involving a FEM as well as a finite volume modelling of the flow within the joints, based on the measured void map are in progress for a more precise comparison to the experimental results. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
13.
岩体节理表面几何特性描述 总被引：1，自引：0，他引：1
岩体节理表面几何特征对岩体变形、刚度、剪切强度和水渗导性有重要影响,一般用节理粗糙度系数（ＪＲＣ）、节理吻合系数（ＪＭＣ）来描述。本文用节理表面分维（ＪＳＦ）来描述节理表面形态的复杂性,为节理表面几何特征描述提供了一个新的方法。 相似文献
14.
Strength and dilatancy of jointed rocks with granular fill 总被引：1，自引：1，他引：0
Ashutosh Trivedi 《Acta Geotechnica》2010,5(1):15-31
It is well recognised that the strength of rock masses depends upon the strain history, extent of discontinuities, orientation
of plane of weakness, condition of joints, fill material in closely packed joints and extent of confinement. Several solutions
are available for strength of jointed rock mass with a set of discontinuities. There is a great multiplicity in the proposed
relationships for the strength of jointed rocks. In the present study, the author conceives the effect of increasing stresses
to induce permanent strains. This permanent strain appears as micro crack, macro crack and fracture. A fully developed network
of permanent deformations forms joint. The joint may contain deposits of hydraulic and hydrothermal origin commonly known
as gouge. The joint factor numerically captures varied engineering possibilities of joints in a rock mass. The joints grow
as an effect of loading. The growth of the joints is progressive in nature. It increases the joint factor, which modifies
the failure stresses. The dilatancy explains the progressive failure of granular media. Hence, a mutual relationship conjoins
effectively the strength of jointed rock and a dilatancy-dependent parameter known as relative dilatancy. This study provides
a simple and integral solution for strength of jointed rocks, interpreted in relation to the commonly used soil, and rock
parameters, used for a realistic design of structure on rock masses. It has scope for prediction of an equivalent strength
for tri-axial and plane strain conditions for unconfined and confined rock masses using a simple technique. 相似文献
15.
G. Swan 《Rock Mechanics and Rock Engineering》1983,16(1):19-38
Summary The measurement of surface profiles is presented as a useful and simple approach to classifying statistically the essential features of rock joints. After introducing the reader to some existing analytical joint contact models for normal loading, a discrete numerical technique is developed. Using this technique the mechanical behaviour of a number of different slate joints is examined. The functional relationships between nominal stress, stiffness, true contact area and initial aperture are shown, for this class of joints, to be surprisingly simple. Experimental evidence is used to substantiate the numerical results. From the point of view of in-situ joint stiffness and hydraulic conductivity, numerical predictions seem feasible provided the degree of mating at some known stress level can be determined. 相似文献
16.
Experimental Study of Ultrasonic Waves Propagating Through a Rock Mass with a Single Joint and Multiple Parallel Joints 总被引：2，自引：1，他引：1
Xiaolin Huang Shengwen Qi Songfeng Guo Wanli Dong 《Rock Mechanics and Rock Engineering》2014,47(2):549-559
Experiments were conducted to study the relationship between the transmission ratio (TR) and normal stress, joint roughness, joint number and frequency of incident waves, respectively, when ultrasonic waves pass across a rock mass with one joint and multiple parallel joints oriented normally. The ultrasonic waves were generated and received by pairs of piezoelectric transducers and recorded by an ultrasonic detector. The specimens were subjected to normal stress by a hydraulic jack and loading frame. The jointed rock mass was produced by superposing rock blocks in the study. Rough joints were produced by grooving notches on the planar joints formed by sawing directly. In the case of multiple parallel joints, the overall thickness of specimens was maintained while the joint number changed. Three pairs of P-wave transducers and one pair of S-wave transducers with different frequencies were, respectively, applied and all transducers emitted signals perpendicular to the joints in the experiment. The results indicate that TR increases with increasing normal stress while the increment rate decreases gradually. This is particularly so when the normal stress is high enough that TR will approximate 1 even if the rock mass has many joints. In addition, the experiments indicate that the higher the wave’s frequency, the lower its TR, and this phenomenon is gradually reduced as the normal stress increases. In response to S-waves, TR increases with increase in joint roughness; however, in response to P-waves, TR decreases gradually with increase in joint roughness. For multiple parallel joints in a fixed thickness rock mass with normally incident P-waves, TR does not always decrease with increase in the number of joints, and there is a threshold joint spacing for a certain incident wave: when the joint spacing is smaller than the threshold value, TR will increase with a decrease in joint spacing. The experimental results support similar conclusions based on analytical results drawn by Cai and Zhao (Int J Rock Mech Min Sci 37(4):661–682, 2000), Zhao et al. (Int J Rock Mech Min Sci 43(5):776–788, 2006b) and Zhu et al. (J Appl Geophys 73:283–288, 2011a). 相似文献
17.
利用RQD估算岩体不同深度的平均渗透系数和平均变形模量 总被引：2，自引：1，他引：1
渗透系数是进行裂隙岩体渗流模拟的必备参数,变形模量是工程岩体数值模拟的必备参数。大量研究中忽视了渗透系数和变形模量随深度变化这一重要规律,从而影响模拟结果的可靠性。为此,探讨了利用极易获取的RQD（岩石质量指标）资料估算不同深度的渗透系数和变形模量的可行性。通过以某花岗岩体为例,研究发现,RQD均值随深度增大,渗透系数均值随深度减小,其相关性很好。因此,利用RQD估算不同深度的平均渗透系数是可行的。根据RQD随深度的变化,利用经验公式估算了不同深度的变形模量均值和变化范围。估算得到的变形模量与实测结果基本一致。 相似文献
18.
节理岩体蠕变特性研究 总被引：13，自引：3，他引：10
在已知岩石和节理蠕变规律的前提下,推导了节理岩体蠕变模型的一般表达式。假定岩石体积变形和节理法向压缩变形为弹性变形,忽略节理的剪胀现象,认为只有岩石畸变和节理剪切滑移与时间有关,从而推导了含三组相交节理的岩体蠕变模型及其参数。根据反演出的岩石和节理蠕变模型,计算了含三组相交节理的岩体在单轴应力作用下一些节理参数对岩体单轴蠕变的影响。分析表明,节理间距、剪胀系数以及节理夹角都对岩体的单轴蠕变变形有明显影响。节理间距越大,剪胀系数越大,节理夹角越小,节理岩体的单轴蠕变柔量也就越小,岩体的蠕变变形也越小。 相似文献