首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Fluid inclusions that bear halite daughter minerals were discovered in volcanic rocks at Pingnan area in the Dongying sag. The samples of the fluid inclusions collected from the BGX-15 well drill cores are hosted in quartz of diorite-porphyrite. The daughter minerals are identified as NaCl crystals after being observed under a microscope and analyzed by in situ Raman spectroscopy at −185°C. The results of micro-thermal analysis show that the homogenization temperatures of primary fluid inclusions are between 359 and 496°C, and the salinities of fluid inclusions are from 43.26 to 54.51 wt-%. All fluid inclusions in the studied samples can be divided into five types including primary fluid inclusions and secondary fluid inclusions. The fact that five types of fluid inclusions were symbiotic in the same quartz grain implies that immiscibility happened in magma. Due to the decrease in temperature and pressure during the ascent of magma, the fluids became intensively immiscible. This process accelerates the degassing of CO2 from magma, but the remnant fluids with high salinity are preserved in fluid inclusions. Thus, the primary fluid inclusions are mainly in NaCl-H2O fluids and poor in CO2. The results of our study indicate that the degassing of magma and accumulation of CO2 gas at the Pingnan area are relative to the immiscibility of high salinity fluids. This discovery is important because it can help us have a further understanding of the mechanism of magma degassing and accumulation of the inorganic CO2 in eastern China. Translated from Acta Geologica Sinica, 2006, 80(11): 1699–1705 [译自: 地质学报]  相似文献   

2.
Fluid inclusions in quartz are known to modify their shapes and microstructures (textures) during weak plastic deformation. However, such changes have not been experimentally demonstrated and criteria are not available to relate them to paleostress conditions. To address these issues, quartz crystals containing natural CO2–H2O–NaCl fluid inclusions have been experimentally subjected to compressive deviatoric stresses of 90–250 MPa at 700°C and ~600 MPa confining pressure. Strains of up to 1% cause the inclusions to develop irregular shapes and to generate microcracks in crystallographic planes oriented subperpendicular to the major compression axis, σ 1. The uniform alignment of the microcracks imparts a planar fabric to the samples. The microcracks heal and form swarms of tiny satellite inclusions. These new inclusions lose H2O by diffusion, thereby triggering plastic deformation of the surrounding quartz via H2O-weakening. Consequently, the quartz samples deform plastically only in domains originally rich in inclusions. This study shows that fluid inclusions deformed by deviatoric stresses may indeed record information on paleostress orientations and that they play a key role in facilitating crystal-plastic deformation of quartz.  相似文献   

3.
The Hokko prospect is located in the Minamikayabe area southwestern Hokkaido, Japan, where gold-bearing quartz veins of Pliocene age are exposed at the surface. The alteration mineral assemblage is typical of low-sulfidation epithermal systems, with the quartz veins associated with adularia alteration overprinted on Late Miocene propylitic alteration. Fluid inclusion studies of the vein quartz reveal mean homogenization temperatures of approximately 220 °C, and the co-existence of low-salinity (<2 wt.% NaCl equivalent) and moderate salinity (2 to 12 wt.% NaCl equivalent) fluid inclusions within the same veins. The moderate salinity fluid inclusions (2–12 wt.% NaCl equivalent) typically have relatively low homogenization temperatures between 150° to 200 °C. The results obtained from stable isotope analysis of  δ18O in quartz vein material showed a gradual decrease in  δ18O signatures with increasing depth. The majority of the samples have calculated fluid source signatures (δ18OH2O) between −8.0 and −10.0‰, but there is a significant change in the composition above 185 m drill depth. The shallower samples in particular show a wide range of oxygen isotope signatures that are associated with the moderate salinity fluid inclusions. We interpret that low-salinity inclusions within the Hokko system represent the composition of the liquid phase of the fluid, before boiling, and that the moderate-salinity inclusions are representative of the residual liquid phase, after extensive non-adiabatic boiling and vapor loss in an open system. This mechanism resulted in the entrapment of fluids with variable salinities at the same time, and in close proximity to each other. This is also reflected in the  δ18OH2O values which become more variable and heavier where the moderate-salinity inclusions occur. Deposition of ore minerals within the Hokko vein system also occurred at this time as a result of boiling and gas loss. Received: 30 May 1997 / Accepted: 6 January 1998  相似文献   

4.
Emerald mineralisation in Colombia is located in two distinct zones along the borders of the Eastern Cordillera, some 80 km apart. Mineralisation in the western zone has been dated at ca. 35 Ma whereas in the eastern zone it is 30 Ma older. Crush leach analysis of the electrolyte chemistry of fluid inclusions contained in emerald, quartz, calcite, dolomite and fluorite from both zones, demonstrates that in each region brines associated with emerald mineralisation range between two extremes with many samples yielding intermediate compositions. Fluid 1, found mainly in emerald-hosted fluid inclusions, is dominated by NaCl with high Cl:Br ratios indicating that the salinity was derived by dissolution of halite, most probably from the local salt beds. Fluid 2, found notably in quartz hosted-fluid inclusions, is of similar salinity but contains less Na and significant concentrations of Ca–K–Fe–Cl and other cations. It has lower Cl:Br ratios, more comparable with formation waters, but is inferred to have obtained part of its salinity by halite dissolution. Bivariate plots of almost all cations have linear or sublinear trends regardless of the mineral hosting the inclusions or the locality from which the samples originated, demonstrating that mixing of the two saline fluids has occurred. Because the same two fluids occur in both eastern and western zones, despite the difference in space and time, it is inferred that fluid compositions were rock controlled by similar interactions with evaporites and black shales in both instances. It is proposed that beryllium was transported as Be–F complexes in the NaCl-fluid, and was precipitated as emerald after mixing with the calcic brine caused precipitation of fluorite and parisite. Received: 9 April 1999 / Accepted: 14 March 2000  相似文献   

5.
Fluid inclusions in quartz are known to modify their densities during shear deformation. Modifications of chemical composition are also suspected. However, such changes have not been experimentally demonstrated, their mechanisms remain unexplained, and no criteria are available to assess whether deformed inclusions preserve information on paleofluid properties. To address these issues, quartz crystals containing natural CO2–H2O–NaCl fluid inclusions have been experimentally subjected to compressive deviatoric stresses of 90–250 MPa at 700°C and ~600 MPa confining pressure. The resulting microcracking of the inclusions leads to expansion by up to 20%, producing low fluid densities that bear no relation to physical conditions outside the sample. Nevertheless, the chemical composition of the precursor inclusions is preserved. With time the microcracks heal and form swarms of tiny satellite inclusions with a wide range of densities, the highest reflecting the value of the maximum principle stress, σ 1. These new inclusions lose H2O via diffusion, thereby passively increasing their salt and gas contents, and triggering plastic deformation of the surrounding quartz via H2O-weakening. Using microstructural criteria to identify the characteristic types of modified inclusions, both the pre-deformation fluid composition and syn-deformation maximum stress on the host mineral can be derived from microthermometric analysis and thermodynamic modelling.  相似文献   

6.
Fluid inclusions were studied in quartz samples from early (stage I) gold-poor quartz veins and later (stage II) gold- and sulphide-rich quartz veins from the Wenyu, Dongchuang, Qiangma, and Guijiayu mesothermal gold deposits in the Xiaoqinling district, China. Fluid inclusion petrography, microthermometry, and bulk gas analyses show remarkably consistent fluid composition in all studied deposits. Primary inclusions in quartz samples are dominated by mixed CO2-H2O inclusions, which have a wide range in CO2 content and coexist with lesser primary CO2-rich and aqueous inclusions. In addition, a few secondary aqueous inclusions are found along late-healed fractures. Microthermometry and bulk gas analyses suggest hydrothermal fluids with typically 15–30 mol% CO2 in stage I inclusions and 10–20 mol% CO2 in stage II inclusions. Estimates of fluid salinity decrease from 7.4–9.2 equivalent wt.% NaCl to 5.7–7.4 equivalent wt.% NaCl between stage I and II. Primary aqueous inclusions in both stages show consistent salinity with, but slightly lower Th total than, their coexistent CO2-H2O inclusions. The coexisting CO2-rich, CO2-H2O, and primary aqueous inclusions in both stage I and II quartz are interpreted to have been trapped during unmixing of a homogeneous CO2-H2O parent fluid. The homogenisation temperatures of the primary aqueous inclusions give an estimate of trapping temperature of the fluids. Trapping conditions are typically 300–370 °C and 2.2 kbar for stage I fluids and 250–320 °C and 1.6 kbar for stage II fluids. The CO2-H2O stage I and II fluids are probably from a magmatic source, most likely devolatilizing Cretaceous Yanshanian granitoids. The study demonstrates that gold is largely deposited as pressures and temperatures fall accompanying fluid immiscibility in stage II veins. Received: 15 May 1997 / Accepted: 10 June 1998  相似文献   

7.
The nature and abundance of dislocations in quartz surrounding fluid inclusions were studied to obtain a better understanding of processes associated with fluid inclusion reequilibration. Synthetic fluid inclusions containing 10 wt% NaCl aqueous solution were formed in three samples at 700 °C and 5 kbar. One of the samples was quenched along an isochore to serve as a reference sample. The other two samples were quenched along a P-T path that generated internal pressures in excess of the confining pressure. The two samples were held at the final reequilibration P-T conditions of 625 °C and 2 kbar for 30 and 180 days, respectively. Following the experiments, microstructures associated with fluid inclusions were examined with the TEM. Quartz in healed fractures in the reference sample that was quenched isochorically shows a moderate dislocation activity. Quartz adjacent to reequilibrated fluid inclusions in the other two samples, however, showed a marked increase in dislocation activity compared to the un-reequilibrated sample. Deformation of the inclusion walls occurred anisotropically by expansion of mobile dislocations in their slip systems. Dislocation expansion was controlled by glide in the rhombohedral planes {1 0 1 1} that was restricted to narrow zones (≤3 μm) in the immediate vicinity of the fluid inclusion walls outside of the healed fracture plane. These plastic zones were observed after both short term (30 days) and long term (180 days) experiments and are attributed to hydrolytic weakening of quartz around fluid inclusions owing to diffusion of water into the quartz matrix during the experiment. The close spatial association of submicroscopic water bubbles with dislocations, and the rarity of water bubbles in the reference sample, show clearly that in both the 30 and 180 day experiments reequilibration involves water loss from the fluid inclusions. Our results indicate that synthetic fluid inclusions in this study recover (chemically and volumetrically), even at relatively fast experimental loading rates, such that internal stresses never reach the point of brittle failure. The driving force for fluid inclusion deformation involves two related mechanisms: plastic deformation of hydrolytically weakened wet quartz in the healed fracture, and water leakage associated with preexisting and strain-induced dislocations. Received: 5 May 1998 / Accepted: 10 February 2000  相似文献   

8.
The major Ghanaian lode gold deposits are preferentially aligned along the western and eastern contacts of the Kumasi Basin with the Ashanti and Sefwi Belts, respectively. The investigated area of the Abawso small-scale concession, covering the workings of the old Ettadom mine, is situated 3 km west of the lithological contact of the Birimian metavolcanic rocks of the Akropong Belt in the east with the Birimian metasedimentary rocks of the Kumasi Basin in the west. The rocks of the Abawso concession represent a steeply NW-dipping limb of a SE-verging anticline with an axis plunging to the SW. Quartz veining occurs predominantly in the form of en échelon dilatational veins along NNE–SSW-striking shear zones of a few metres width and shows evidence of brittle and ductile deformation. Also stockwork-style quartz veining occurs in the vicinity of the main shaft of the old Ettadom mine. Hydrothermal alteration includes sericitisation, sulphidation and locally carbonatisation. The auriferous quartz veins mainly follow the trend of brittle to ductile deformed quartz veins; however, some occur in stockwork. Fluid inclusion studies reveal a large number of H2O inclusions along intragranular trails in auriferous quartz vein samples, as well as an overall dominance of H2O and H2O-CO2 inclusions over CO2 inclusions. Textural observations and physico-chemical fluid inclusion properties indicate post-entrapment modifications for all quartz vein samples due to grain boundary migration recrystallisation. This process is interpreted to be responsible for the generation of the CO2 inclusions from a H2O-CO2 parent fluid. In comparison with mineralisation at the Ashanti and Prestea deposits, which are characterised by CO2±N2 inclusions, the observed inclusion assemblage may be due to a shallower crustal level of mineralisation, or different degrees and styles of recrystallisation, or a less pronounced development of laminated quartz veins due to comparably restricted pressure fluctuations. Furthermore, the microthermometric observations allow the reconstruction of a possible retrograde P-T path, depicting near-isothermal decompression in the P-T range of the brittle/ductile transition.Editorial handling: E. Frimmel  相似文献   

9.
雪鸡坪铜矿床产于印支晚期石英二长闪长玢岩-石英闪长玢岩-石英二长斑岩复式侵入体内,为一斑岩型铜矿床。矿床形成经历了多阶段热液成矿作用,主要有微细脉浸染状黄铁矿±黄铜矿-石英、细脉状辉钼矿±黄铁矿±黄铜矿-石英及微细脉状贫硫化物-石英-方解石等。流体包裹体岩相学、显微测温、激光拉曼及碳、氢、氧同位素综合研究表明,微细脉浸染状黄铁矿±黄铜矿-石英阶段石英中主要发育含Na Cl子矿物三相及气液两相包裹体,与含矿的石英二长斑岩石英中发育的流体包裹体特征相似,表明成矿流体主要为中高温、高盐度Na Cl-H2O体系热液,可能主要来源于印支期石英二长斑岩侵入体;辉钼矿±黄铁矿±黄铜矿-石英中主要发育含CO2三相及气液两相包裹体,成矿流体为中温、低盐度Na Cl-CO2-H2O体系热液,与前者来源明显不同;贫硫化物-石英-方解石石英中主要发育气液两相包裹体,成矿流体为中低温、低盐度Na Cl-H2O体系热液,推测其可能较多来自于大气降水。因此,雪鸡坪铜矿床为不同来源、不同地球化学性质热液叠加成矿作用的结果。  相似文献   

10.
庐山星子群变质流体的包裹体研究   总被引：2，自引：1，他引：1  
唐红峰  刘丛强  倪培 《矿物学报》2000,20(3):286-292
庐山星子群沉积变质岩中发育平行区域片理的石英脉和长英质脉体,这些脉体的石英晶体内富含原生的流体包裹体,包括低盐度的含液体ＣＯ２包裹体、液体包裹体、纯ＣＯ２包裹体和高盐度含子矿物包裹体。它们与中生代伟晶岩脉体中包裹体在均一温度、盐度和ＣＯ２密度等方面的明显差异和变质脉体中含液体ＣＯ２包裹体的等容线位置,表明变质脉体石英中的流体包裹体是在变质作用期间被捕获的部分变质流体,进一步证实了脉体是与变质作用同  相似文献   

11.
Fluid inclusions were studied in samples from the Ashanti, Konongo-Southern Cross, Prestea, Abosso/Damang and Ayanfuri gold deposits in the Ashanti Belt, Ghana. Primary fluid inclusions in quartz from mineralised veins of the Ashanti, Prestea, Konongo-Southern Cross, and Abosso/Damang deposits contain almost exclusively volatile species. The primary setting of the gaseous (i.e. the fluid components CO2, CH4 and N2) fluid inclusions in clusters and intragranular trails suggests that they represent the mineralising fluids. Microthermometric and Raman spectroscopic analyses of the inclusions revealed a CO2 dominated fluid with variable contents of N2 and traces of CH4. Water content of most inclusions is below the detection limits of the respective methods used. Aqueous inclusions are rare in all samples with the exception of those from the granite-hosted Ayanfuri mineralisation. Here inclusions associated with the gold mineralisation contain a low salinity (<6 eq.wt.% NaCl) aqueous solution with variable quantities of CO2. Microthermometric investigations revealed densities of the gaseous inclusions of 0.65 to 1.06 g/cm3 at Ashanti, 0.85 to 0.98 g/cm3 at Prestea, up to 1.02 g/cm3 at Konongo-Southern Cross, and 0.8 to 1.0 g/cm3 at Abosso/Damang. The fluid inclusion data are used to outline the PT ranges of gold mineralisation of the respective gold deposits. The high density gaseous inclusions found in the auriferous quartz at Ashanti and Prestea imply rather high pressure trapping conditions of up to 5.4 kbar. In contrast, mineralisation at Ayanfuri and Abosso/Damang is inferred to have occurred at lower pressures of only up to 2.2 kbar. Mesothermal gold mineralisation is generally regarded to have formed from fluids characterized by H2O > CO2 and low salinity ( ±  6 eq.wt.%NaCl). However, fluid inclusions in quartz from the gold mineralisations in the Ashanti belt point to distinctly different fluid compositions. Specifically, the predominance of CO2 and CO2 >> H2O have to be emphasized. Fluid systems with this unique bulk composition were apparently active over more than 200␣km along strike of the Ashanti belt. Fluids rich in CO2 may present a hitherto unrecognised new category of ore-forming fluids. Received: 30 May 1996 / Accepted: 8 October 1996  相似文献   

12.
Fluid inclusions hosted in quartz and specular hematite from auriferous (jacutinga) and barren veins in the Quadrilátero Ferrífero (QF) have been studied using conventional and near infrared microscopy, respectively. The mineralization consists of veins that cross-cut metamorphosed iron formation (itabirite) of the Paleoproterozoic Itabira Group. The sample suite comprises hematite from veins from the low-strain domain in the W and SW of the study area, as well as hematite samples from the eastern high-strain domain in the central and NE parts of the QF. Halogen ratios of fluid inclusions in quartz and hematite from all studied deposits are consistent with a fluid evolved from dissolving and reprecipitating halite that was subsequently diluted. Fluid inclusions hosted in quartz and hematite are characterized by consistent Na/K ratios and considerable SO4 contents, and suggest similar formation conditions and, perhaps, fluid origin from a common source. Na/K and Na/Li fluid mineral geothermometers indicate water–rock interaction at approximately 340±40°C. Hematites from the high-strain domain contain fluid inclusion assemblages of high-temperature aqueous-carbonic and multiphase high-salinity, high-temperature aqueous inclusions probably due to fluid immiscibility in the system H2O–NaCl–CO2. Fluid inclusions hosted in hematite from barren veins in the low-strain domain, as well as in hematite from jacutinga-type mineralization from the central part of the QF, only host multiphase aqueous fluid inclusions all showing narrow ranges of salinity (7.2–11.7 wt.% NaCl equiv.) and homogenization temperatures (148 to 229°C). Lower homogenization temperatures and the absence of CO2-rich inclusions in specular hematite from these occurrences are attributed to carbonate precipitation and/or CO2 escape due to cooling during fluid migration from the high- to the low-strain domain. Pb–Pb and U–Pb systematics of gold, hematite and hematite-hosted fluid inclusions in combination with geochemical evidence indicate distinct sources for Pd, Au, and Pb. The formation of specular hematite veins may be related to retrograde metamorphic fluids being released during the Brazilian orogenic cycle (600–700 Ma). The Pb isotopic characteristics of all samples are readily reconciled in a simple model that involves two different Paleoproterozoic or Archean source lithologies for lead and reflects contrasting depths of fluid percolation during the Brasiliano orogeny.  相似文献   

13.
The Betam gold deposit, located in the southern Eastern Desert of Egypt, is related to a series of milky quartz veins along a NNW-trending shear zone, cutting through pelitic metasedimentary rocks and small masses of pink granite. This shear zone, along with a system of discrete shear and fault zones, was developed late in the deformation history of the area. Although slightly sheared and boudinaged within the shear zone, the auriferous quartz veins are characterised by irregular walls with a steeply plunging ridge-in-groove lineation. Shear geometry of rootless intra-folial folds and asymmetrical strain shadows around the quartz lenses suggests that vein emplacement took place under a brittle–ductile shear regime, clearly post-dating the amphibolite-facies regional metamorphism. Hydrothermal alteration is pervasive in the wallrock metapelites and granite including sericitisation, silicification, sulphidisation and minor carbonatisation. Ore mineralogy includes pyrite, arsenopyrite and subordinate galena, chalcopyrite, pyrrhotite and gold. Gold occurs in the quartz veins and adjacent wallrocks as inclusions in pyrite and arsenopyrite, blebs and globules associated with galena, fracture fillings in deformed arsenopyrite or as thin, wire-like rims within or around rhythmic goethite. Presence of refractory gold in arsenopyrite and pyrite is inferred from microprobe analyses. Clustered and intra-granular trail-bound aqueous–carbonic (LCO2 + Laq ± VCO2) inclusions are common in cores of the less deformed quartz crystals, whereas carbonic (LCO2 ± VCO2) and aqueous H2O–NaCl (L + V) inclusions occur along inter-granular and trans-granular trails. Clathrate melting temperatures indicate low salinities of the fluid (3–8 wt.% NaCl eq.). Homogenisation temperatures of the aqueous–carbonic inclusions range between 297 and 323°C, slightly higher than those of the intra-granular and inter-granular aqueous inclusions (263–304°C), which are likely formed during grain boundary migration. Homogenisation temperatures of the trans-granular H2O–NaCl inclusions are much lower (130–221°C), implying different fluids late in the shear zone formation. Fluid densities calculated from aqueous–carbonic inclusions along a single trail are between 0.88 and 0.98 g/cm3, and the resulting isochores suggest trapping pressures of 2–2.6 kbar. Based on the arsenopyrite–pyrite–pyrrhotite cotectic, arsenopyrite (30.4–30.7 wt.% As) associated with gold inclusions indicates a temperature range of 325–344°C. This ore paragenesis constrains f S2 to the range of 10−10 to 10−8.5 bar. Under such conditions, gold was likely transported mainly as bisulphide complexes by low salinity aqueous–carbonic fluids and precipitated because of variations in pH and f O2 through pressure fluctuation and CO2 effervescence as the ore fluids infiltrated the shear zone, along with precipitation of carbonate and sericite. Wallrock sulphidation also likely contributed to destabilising the gold–bisulphide complexes and precipitating gold in the hydrothermal alteration zone adjacent to the mineralised quartz veins.  相似文献   

14.
Melt and fluid inclusions were investigated in six quartz phenocryst samples from the igneous rocks of the extrusive (ignimbrites and rhyolites) and subvolcanic (granite porphyries) facies of the Lashkerek Depression in the Kurama mining district, Middle Tien Shan. The method of inclusion homogenization was used, and glasses from more than 40 inclusions were analyzed on electron and ion microprobes. The chemical characteristics of these inclusions are typical of silicic magmatic melts. The average composition is the following (wt %): 72.4 SiO2, 0.06 TiO2, 13.3 Al2O3, 0.95 FeO, 0.03 MnO, 0.01 MgO, 0.46 CaO, 3.33 Na2O, 5.16K2O, 0.32 F, and 0.21 Cl. Potassium strongly prevails over sodium in all of the inclusions (K2O/Na2O averages 1.60). The average total of components in melt inclusions from five samples is 95.3 wt %, which indicates a possible average water content in the melt of no less than 3–4 wt %. Water contents of 2.0 wt % and 6.6 wt % were determined in melt inclusions from two samples using an ion microprobe. The analyses of ore elements in the melt inclusions revealed high contents of Sn (up to 970 ppm), Th (19–62 ppm, 47 ppm on average), and U (9–26 ppm, 18 ppm on average), but very low Eu contents (0.01 ppm). Melt inclusions of two different compositions were detected in quartz from a granite porphyry sample: silicate and chloride, the latter being more abundant. In addition to Na and K chlorides, the salt inclusions usually contain one or several anisotropic crystals and an opaque phase. The homogenization temperatures of the salt inclusions are rather high, from 680 to 820°C. In addition to silicate inclusions with homogenization temperatures of 820–850°C, a primary fluid inclusion of aqueous solution with a concentration of 3.7 wt % NaCl eq. and a very high density of 0.93 g/cm3 was found in quartz from the ignimbrite. High fluid pressure values of 6.5–8.3 kbar were calculated for the temperature of quartz formation. These estimates are comparable with values obtained by us previously for other regions of the world: 2.6–4.3 kbar for Italy, 3.7 kbar for Mongolia, 3.3–8.7 kbar for central Slovakia, and 3.3–9.6 kbar for eastern Slovakia. Unusual melt inclusions were investigated in quartz from another ignimbrite sample. In addition to a gas phase and transparent glass, they contain spherical Feoxide globules (81.2 wt % FeO) with high content of SiO2 (9.9 wt %). The globules were dissolved in the silicate melt within a narrow temperature range of 1050–1100°C, and the complete homogenization of the inclusions was observed at temperatures of 1140°C or higher. The combined analysis of the results of the investigation of these inclusions allowed us to conclude that immiscible liquids were formed in the high-temperature silicic magma with the separation of iron oxide-dominated droplets.  相似文献   

15.
  Copper and subordinate molybdenum mineralization at Malanjkhand occurs within a fracture-controlled quartz-reef enclosed in a pink granitoid body surrounded by grey-granitoids constituting the regional matrix. Sulfide-bearing stringers, pegmatites with only quartz + microcline and sulfide disseminations, all within the pink-granitoid, represent other minor modes of occurrences. Despite this diversity in mode of occurrence, the mineralogy of ores is quite consistent and conform to a common paragenetic sequence comprising an early `ferrous' stage of precipitation of magnetite (I) and pyrite (I) and, the main-stage chalcopyrite mineralization with minor sphalerite, pyrite (II), magnetite (II), molybdenite and hematite. Both stages witnessed continuous precipitation of quartz ± microcline ± (chlorite, biotite and epidote). The enclosing pink-granitoid and the regional grey-granitoids display alteration features such as saussuritization of plagioclase, breakdown of hornblende and chloritization of biotite on a regional scale, indicating interaction with a pervasive fluid. Quartz and microcline precipitation mostly restricted within the pink granitoid, postdates this alteration. Four types of primary inclusions were encountered in quartz from ore samples: (1) type-I – aqueous-biphase(L + V) inclusions, the commonest variety in all ore types; (2) type-II – aqueous-carbonic(Laq + Lcarb ± Vcarb); (3) type-III – pure-carbonic(Lcarb ± Vcarb) – type-II and III being restricted to stringer and pegmatitic ores, and (4) rare polyphase (Laq + Vaq + calcite/gypsum) inclusions. Quartz in granitoids contain primary type-I inclusions only. Type-I inclusions from ore samples furnish a temperature range (after a rough pressure correction to the T H  -maxima of 140–180 °C) of 150–275 °C and a moderately low salinity of 4–12 wt.% NaCl equivalent. This is inferred to represent the signature of the major component (F2) of the ore fluid. A few type-I inclusions of higher T M (up to 380 °C) and low salinity and density represent the other (F1) identifiable component of the ore fluid present in low proportion. The T H  -maxima and the total range in salinity of type-I inclusions in quartz from granitoids are strikingly similar to those from the ore samples. Composition of syn-ore chlorites furnished a temperature range of 185–327 °C, which conforms to the fluid inclusion microthermometric data. Pressure estimates using standard fluid inclusion geobarometric methods, vary from 550 to 1790 bar in the stringer ores. Observed temperature-salinity/density relationships are best explained by a two-stage evolution model of the ore fluid: the first stage witnessed mixing of the two components, F1 and F2 in unequal proportion, bringing about mineralization. The second stage of evolution was marked by the separation of a carbonic component on continued sulfide precipitation and attendant increase in salinity of the fluid. The F1 component emerged as a distinct, heated and (CO2 + S)-charged entity due to steam-heating and contamination of the early-ingressed F2 fluid at the fracture zone. The pervasive fluid phase in the surrounding granitoids contributed the F2 component. Received: (10 August 1994), 15 August 1995 / Accepted: 12 January 1996  相似文献   

16.
The Olympias Pb-Zn(Au, Ag) sulfide ore deposit, E. Chalkidiki, N. Greece, is hosted by marbles of the polymetamorphic Kerdilia Formation of Paleozoic or older age. The geologic environment of the ore also comprises biotite-hornblende gneisses and amphibolites intruded by Tertiary pegmatite-aplite dikes, lamprophyre dikes, the 30-Ma Stratoni granodiorite, and porphyritic stocks. Only limited parts of the deposit display shear folding and brecciation; most of it is undeformed. Microthermometry of fluid inclusions in gangue syn-ore quartz indicates three types of primary and pseudosecondary inclusions: (1) H2O-rich, 1–18 wt.% NaCl equivalent, <3.6 mol% CO2; (2) H2O-CO2 inclusions, <4wt.% NaCl equivalent, with variable CO2 contents, coexisting in both undeformed and deformed ore; (3) aqueous, highsalinity (28–32 wt,% NaCl equivalent) inclusions found only in undeformed ore. Type 2 inclusions are differentiated into two sub-types: (2a) relatively constant CO2 content in the narrow range of 8–15 mol% and homogenization to the liquid phase; (2b) variable CO2 content between 18 and 50 mol% and homogenization to the vapor phase. Type 1 and 2b inclusions are consistent with trapping of two fluids by unmixing of a high-temperature, saline, aqueous, CO2-bearing fluid of possible magmatic origin, probably trapped in type 2a inclusions. Fluid unmixing and concomitant ore mineralization took place at temperatures of 350 ± 30 °C and fluctuating pressures of less than 500 bar, for both undeformed and deformed ores. The wide salinity range of type 1 inclusions probably represents a complex effect of salinity increase, due to fluid unmixing and volatile loss, and dilution, due to mixing with low-salinity meteoric waters. High solute enrichment of the residual liquid, due to extreme volatile loss during unmixing, may account for high salinity type 3 inclusions. The Olympias fluid inclusion salinity-temperature gradients bear similarities to analogous gradients related to Pb-Zn ores formed in “granite”-hosted, low-T distalskarn, skarn-free carbonate-replacement and epithermal environments.  相似文献   

17.
Summary The low-pressure emplacement of a quartz diorite body in the metapelitic rocks of the Gennargentu Igneous Complex (Sardinia, Italy) produced a contact metamorphic aureole and resulted in migmatisation of part of the aureole through partial melting. The leucosome, formed by dehydration melting involving biotite, is characterised by granophyric intergrowth and abundant magnetite crystals. A large portion of the high temperature contact aureole shows petrographic features that are intermediate between quartz diorite and migmatite s.s. (i.e. hybrid rocks). A fluid inclusion study has been performed on quartz crystals from the quartz diorite and related contact aureole rocks, i.e. migmatite sensu stricto (s.s.) and hybrid rocks. Three types of fluid inclusions have been identified: I) monophase V inclusions, II) L + V, either L-rich or V-rich aqueous saline inclusions and III) multiphase V + L + S inclusions. Microthermometric data characterised the trapped fluid as a complex aqueous system varying from H2O–NaCl–CaCl2 in the quartz diorite to H2O–NaCl–CaCl2–FeCl2 in the migmatite and hybrid rocks. Fluid salinities range from high saline fluids (50 wt% NaCl eq.) to almost pure aqueous fluid. Liquid-vapour homogenisation temperatures range from 100 to over 400 °C with an average peak around 300 °C. Temperatures of melting of daughter minerals are between 300 and 500 °C. Highly saline liquid- and vapour-rich inclusions coexist with melt inclusions and have been interpreted as brine exsolved from the crystallising magma. Fluid inclusion data indicate the formation of fluid of high iron activity during the low-pressure partial melting and a fluid mixing process in the hybrid rocks.  相似文献   

18.
盐度是流体包裹体重要的参数之一,利用激光拉曼探针可以快速、准确地测定包裹体盐度,而标准样品的制备是保证该方法准确性的关键。毛细管合成包裹体技术是一种新型的标准样品制备方法,本文利用该方法,制备了不同组成的H2O-NaCl样品,并以此建立了测定包裹体盐度的标准曲线。显微测温结果表明,毛细管合成包裹体标准样品盐度的准确性可以达到±0.5%,利用石英和石盐中的合成包裹体对标准曲线进行了检验,结果表明利用标准曲线测定包裹体盐度,测量值与理论值的误差在1%以内。应用该方法制备的标准样品具有操作简便、快捷、样品尺寸与地质样品相类似等特点,兼具了矿物中合成包裹体以及石英试管或玻璃瓶制备标准样品的优势。  相似文献   

19.
The Piaotang deposit is one of the largest vein-type W-polymetallic deposits in southern Jiangxi Province, South China. The coexistence of wolframite and cassiterite is an important feature of the deposit. Based on detailed petrographic observations, microthermometry of fluid inclusions in wolframite, cassiterite and intergrown quartz was undertaken. The inclusions in wolframite were observed by infrared microscope, while those in cassiterite and quartz were observed in visible light. The fluid inclusions in wolframite can be divided into two types: aqueous inclusions with a large vapor-phase proportion and aqueous inclusions with a small vapor-phase ratio. The homogenization temperature (Th) of inclusions in wolframite with large vapor-phase ratios ranged from 280°C to 390°C, with salinity ranging from 3.1 to 7.2 wt% NaCl eq. In contrast, the Th values of inclusions with small vapor-phase ratios ranged from 216°C to 264°C, with salinity values ranging from 3.5 to 9.3 wt% NaCl eq. Th values of primary inclusions in cassiterite ranged from 316°C to 380°C, with salinity ranging from 5.4 to 9.3 wt% NaCl eq. Th values for primary fluid inclusions in quartz ranged from 162°C to 309°C, with salinity values ranging from 1.2 to 6.7 wt% NaCl eq. The results show that the formation conditions of wolframite, cassiterite and intergrown quartz are not uniform. The evolutionary processes of fluids related to these three kinds of minerals are also significantly different. Intergrown quartz cannot provide the depositional conditions of wolframite and cassiterite. The fluids related to tungsten mineralization for the NaCl-H2O system had a medium-to-high temperature and low salinity, while the fluids related to tin mineralization for the NaCl-H2O system had a high temperature and medium-to-low salinity. The results of this study suggest that fluid cooling is the main mechanism for the precipitation of tungsten and tin.  相似文献   

20.
南岭中段骑田岭A型花岗岩与芙蓉超大型锡矿床具有密切的时间和空间关系。流体包裹体地球化学研究表明,骑田岭A型花岗岩石英斑晶中的流体包裹体类型主要有熔融包裹体、流体-熔融包裹体和流体包裹体。流体-熔融包裹体的显微测温学研究结果显示,骑田岭A花岗岩在岩浆演化过程中可以分异出流体,且岩浆分异出的流体与芙蓉超大型锡矿床流体包裹体所反映的高温和高盐度的CaCl2-NaCl-KCl-H2O流体体系的特征相吻合。综合分析表明,芙蓉超大型锡矿床成矿流体中的高盐度流体应为骑田岭黑云母二长花岗岩结晶过程中分异出的富含Cl等挥发份和成矿物质的高盐度热流体。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号