共查询到20条相似文献，搜索用时 46 毫秒
1.
Effect of the inclined weak interlayers on the rainfall response of a bedded rock slope 总被引：1，自引：1，他引：0
Engineering experience shows that outward dipping bedded rock slopes, especially including weak interlayers, are prone to slide under rainfall conditions. To investigate the effect of inclined weak interlayers at various levels of depth below the surface on the variation of displacements and stresses in bedded rock slopes, four geo-mechanical model tests with artificial rainfall have been conducted. Displacements, water content as well as earth pressure in the model were monitored by means of various FBG (Fiber Bragg Grating) sensors. The results showed that the amount of displacement of a slope with a weak interlayer is 2.8 to 6.2 times larger than that of a slope without a weak interlayer during one rainfall event. Furthermore, the position of the weak interlayer in terms of depth below the surface has a significant effect on the zone of deformation in the model. In the slope with a high position weak interlayer, the recorded deformation was larger in the superficial layer of the model and smaller in the frontal portion than in the slope with a low position weak interlayer. The slope with two weak interlayers has the largest deformation at all locations of all test slopes. The slope without a weak interlayer was only saturated in its superficial layer, while the displacement decreased with depth. That was different from all slopes with a weak interlayer in which the largest displacement shifted from the superficial layer to the weak interlayer when rainfall persisted. Plastic deformation of the weak interlayer promoted the formation of cracks which caused more water to flow into the slope, thus causing larger deformation in the slope with weak interlayers. In addition, the slide thrust pressure showed a vibration phenomenon 0.5 to 1 hour ahead of an abrupt increase of the deformation, which was interpreted as a predictor for rainfall-induced failure of bedded rock slopes. 相似文献
2.
In recent major earthquakes, the researchers have found the need for consideration of vertical seismic acceleration for the stability analysis of the man-made and natural slopes. However, in most past studies, the performance of slopes has been assessed by accounting only the horizontal seismic component of the ground motion, without giving due weightage to the effect of vertical component. In the present study, analytical expressions are derived to determine the factor of safety, yield seismic coefficient and consequently the seismic displacement of cohesionless soil slope under combined horizontal and vertical components of the ground motion. The derivation uses the Newmark’s sliding block approach, in which the soil slope with a planar failure surface within the framework of conventional pseudo-static analysis is assumed to follow the Mohr-Coulomb failure criterion. The effects of vertical seismic coefficient on the stability of cohesionless slope have been studied through a set of graphical presentations for a specific range of soil parameters. It is observed that overlooking the effect of the vertical component of the ground motion on factor of safety and the displacement while designing the slope may be detrimental, resulting in the slope failure. The general expressions presented in this paper may be highly useful in the field of earthquake geotechnical engineering practice for designing the cohesionless soil slopes under combined horizontal and vertical seismic loads. 相似文献
3.
In analyzing seismic stability of a slope with upper bound limit analysis method, the slip surface is often assumed as a log-spiral or plane slip surface. However, due to the presence of a weak layer and unfavorable geological structural surface or a bedrock interface with overlying soft strata, the preexisting slip surface of the slope may be irregular and composed of a series of planes rather than strictly log-spiral or plane shape. A computational model is developed for analyzing the seismic stability of slopes with pre-existing slip surfaces. This model is based on the upper bound limit analysis method and can consider the effect of anchor bolts. The soil or rock is deemed to follow the Mohr-Coulomb yield criterion. The slope is divided into multiple block elements along the slip surface. According to the displacement compatibility and the associated flow rule, a kinematic velocity field of the slope can be obtained computationally. The proposed model allows not only calculation of the rate of external work owing to the combined effect of self-weight and seismic loading, but also that of the energy dissipation rate caused by the slip surface, interfaces of block elements and anchorage effect of the anchors. Considering a direct relationship between the rate of external work and the energy dissipation rate, the expressions of yield acceleration and permanent displacement of anchored slopes can be derived. Finally, the validity of this proposed model is illustrated by analysis on three typical slopes. The results showed that the proposed model is more easily formulated and does not need to solve complex equations or time consuming iterations compared with previous methods based on the conditions of force equilibrium. 相似文献
4.
Cracks in rock or soil slopes influence the stability and durability of the slopes. Seismic forces can trigger slope disasters, particularly in the cracked slopes. Considering the nonlinear characteristics of materials, the more generalized nonlinear failure criterion proposed by Baker is adopted. The influence of non-dimensional strength parameters on the stability of cracked slopes under earthquakes is performed using the upper bound limit analysis. The seismic displacement is calculated by adopting the logarithmic spiral failure surface according to the sliding rigid block model. Based on the existing studies, two methods for the stability analysis of cracked slopes under earthquakes are introduced: the pseudo-static method(with the factor of safety(Fs) as an evaluation index), and the displacement-based method(with the seismic displacement as an evaluation index). The pseudo-static method can only determine the instantaneous stability state of the cracked slope, yet the displacement-based methodreflects the stability variation of cracked slopes during earthquakes. The results indicate that the nondimensional strength parameters affect the factor of safety and seismic displacement of slopes significantly. The non-dimensional strength parameter(n) controlling the curvature of strength function shapes on the slope stability is affected by other parameters. Owing to cracks, the effect of non-dimensional strength parameters on seismic displacement becomes more significant. 相似文献
5.
The objective of this research was to assess the characteristics of seismic induced damage and the deformation patterns of pre-stressed cement-grouted cables that are used for rock slope stabilization projects subjected to quasi-static cyclic loading. The experimental configuration includes the installation of 15 pre-stressed cables in a slope model made of concrete blocks (theoretically rigid rock mass) on top of a pre-existing sliding surface. The study showed that: (i) The pre-stressed cables exhibited great seismic performance. Rapid displacement of the model blocks was observed after the complete loss of the initial pre-stress load under continued applied cyclic loads and exceedance of the state of equilibrium, which implies the higher the initial pre-stress load, the better the seismic performance of the rock anchor; (ii) The failure of the pre-stressed cables was due to fracture at the connection of the tendons and cable heads under cyclic loading. The sequence of failure had a distinct pattern. Failure was first observed at the upper row of cables, which experienced the most severe damage, including the ejection of cable heads. No evidence of de-bonding was observed during the cyclic loading; (iii) The stress distribution of the bond length for pre-stressed cables was highly non-uniform. High stress concentrations were observed at both the fixed end and the free end of the bond length both before and immediately after the state of equilibrium is exceeded. The results obtained can be used to evaluate the overall performance of pre-stressed rock anchors subject to seismic loading and their potential as rockfall prevention and stabilization measures. 相似文献
6.
Slope failure in loess terrains of Northern China during spring thawing period is closely related to the freeze-thaw cycling that surface soils inevitably experienced. Field surveys were carried out on natural and artificial slopes in thirteen surveying sites located in the Northern Shaanxi, the center of Loess Plateau, covering five characteristic topographic features including tablelands, ridges, hills, gullies and valleys. Based on the scale that is involved in freeze-thaw cycling, the induced failures can be classified into three main modes, i.e., erosion, peeling and thaw collapse, depending on both high porosity and loose cementation of loess that is easily affected. Model tests on loess slopes with gradients of 53.1°, 45.0° and 33.7° were carried out to reveal the heat transfer, water migration and deformation during slope failure. The surface morphology of slopes was photographed, with flake shaped erosion and cracks noted. For three slope models, time histories for the thermal regime exhibit three obvious cycles of freeze and thaw andthe maximum frost depth develops downwards as freeze-thaw cycling proceeds. Soil water in the unfrozen domain beneath was migrated towards the slope surface, as can be noticed from the considerable change in the unfrozen water content, almost synchronous with the variation of temperature. The displacement in both vertical and horizontal directions varies over time and three obvious cycles can be traced. The residual displacement for each cycle tends to grow and the slopes with higher gradients are more sensitive to potentially sliding during freeze-thaw cycling. 相似文献
7.
随着我国公路建设不断向山区深入, 在地质构造复杂区公路边坡遇到断层破碎带的情况日渐增多, 亟需开展阻滑能力强的抗滑桩结构加固边坡研究。传统的人工挖孔桩施工模式存在高风险、低效率等缺点, 而组合式圆截面抗滑桩具有施工效率高、安全便捷等特点, 为此, 探究其对含断层破碎带边坡的加固效果具有现实意义。采用自主设计的边坡物理试验系统, 设计了5种不同破碎带厚度与组合式圆截面抗滑桩组合的物理模型, 采用坡顶逐级加载的方式模拟加载, 监测桩身应变、桩顶位移和桩后土压力, 采用高速相机捕捉滑体变形破坏图像, 并使用粒子图像测速(PIV)技术对图像进行处理。研究结果表明: 组合式圆截面抗滑桩通过限制桩后滑体水平位移, 并将滑体限制在前、后排桩间来达到加固边坡的效果; 滑体演化分为变形压密、加速变形和破坏滑移3个阶段; 前、后排桩桩后土压力比值介于1/3~1/2之间; 随断层破碎带厚度增加, 滑体水平滑移速率增大, 组合式圆截面抗滑桩的桩顶位移增大, 桩身最大正弯矩减小。模型试验与数值模拟计算的弯矩及桩顶位移较为吻合, 研究成果可为边坡工程组合式圆截面抗滑桩设计提供一定借鉴与参考。 相似文献
8.
软硬互层结构的顺层岩质边坡破坏类型复杂、难于防治, 针对此类边坡地质灾害易发、多发的问题, 从坡面角度、岩层倾向及组合形式、节理分布等方面进行了研究。边坡物理模型试验是揭示边坡变形破坏机理的重要手段, 基于相似理论, 以重庆市万州区孙家滑坡为工程依托, 根据滑坡区地质勘探报告设计了室内边坡物理模型试验; 试验通过顶升模型箱模拟重力加载来探究顺层岩质边坡发生破坏时, 前缘坡角和软弱夹层倾角之间的关系; 结合有限元分析软件Plaxis 2D对物理模型进行了多组数值模拟试验, 以验证软硬互层顺层岩质边坡破坏机制。试验结果表明: 对于顺层岩质边坡, 当软弱夹层的倾角在22°左右, 前缘开挖坡角58°左右时, 顺层岩质边坡容易发生滑动, 滑动面为后缘节理面和软弱夹层的贯通面。因此, 顺层岩质边坡稳定性受层面和节理面密度的控制, 当边坡含多层软弱层面时, 易沿层面和后缘节理贯通面发生破坏, 随着软弱面层数增加, 边坡稳定系数逐渐降低。研究成果可以为公路开挖切坡导致的顺层岩质边坡失稳机理研究及其稳定性评价提供理论依据, 为顺层岩质边坡失稳的预测预报提供支撑。 相似文献
9.
斜坡变形受众多因子综合控制, 不同因子的敏感性与作用规律在变形过程中差异明显。以湖北省阳新县顺层基岩滑坡为研究对象, 通过正交试验结合离散元数值模拟的方法, 研究多个影响因子对应顺层滑坡变形的敏感性并确立主导因素, 随后基于响应面拟合主导因素与滑坡不同部位变形程度间的量化关系, 揭示主导因素交互作用对滑坡变形破坏模式的影响规律。结果表明, 在研究区内坡度与岩层倾角分别为影响顺层滑坡变形的主导与次主导因素, 滑坡的变形破坏模式受控于二者的交互作用。在中-陡倾顺层滑坡中, 当坡度小于岩层倾角时, 滑坡变形主要集中在坡顶, 且变形程度随岩层倾角的增加而增大, 表现出滑移-弯曲的变形破坏模式; 在缓倾顺层滑坡中, 当坡度大于岩层倾角时, 滑坡坡脚位移较坡顶显著, 其坡脚变形程度随坡度的增加而增大, 以滑移-拉裂变形为主。研究成果可为该类滑坡的防治工作提供参考。 相似文献
10.
Guo-qing Chen Run-qiu Huang Feng-shou Zhang Zhen-fei Zhu Yu-chuan Shi Jian-chao Wang 《山地科学学报》2018,15(3):672-684
A new method, the dynamic reduction method (DRM) combined with the strain-softening method, was applied to evaluate the possible slip surface of a highly heterogeneous rock slope of the Dagangshan hydropower station in Southwest China. In DRM, only the strength of the failure elements is reduced and the softening reduction factor K is adopted to calculate the strength parameters. The simulation results calculated by DRM show that the further slip surface on the right slope of the Dagangshan hydropower station is limited in the middle part of the slope, while both SRM (strength reduction method) and LEM (limit equilibrium method) predict a failure surface which extends upper and longer. The observations and analysis from the three recorded sliding events indicate that the failure mode predicted by DRM is more likely the scenario. The results in this study illustrate that for highly heterogeneous slopes with geological discontinuities in different length scales, the proposed DRM can provide a reliable prediction of the location of the slip surface. 相似文献
11.
采空区地表山体侧向变动,不同于一般天然山坡,也与采空区一般上覆岩层的变形破坏有异;它是二者复合机理的效应。本文在分析考察了毗邻电厂的横山顺倾构造山体、剖析了地下采空情况认为:山体侧向变动中,软弱夹层有决定性作用,变动范围、速率和规模与地下采空有关;并利用地质力学模型试验和数值模拟,探索了采动引起山体应力场及变动规律。结果表明,山体岩层的变形、位移、破坏、由直接顶板向地表发展,采空坍陷诱发了软弱夹层的蠕滑,则产生山体侧向滑移;电厂区地表隆起变形是山体侧向滑移挤压地基土的反映。通过现场实际调研、变形观测资料分析与数值模拟和模型试验的对比研究,提出了“坍落拱梁”的成生效应、挤压蠕滑效应、失稳效应;揭露了顺倾构造山体在采空影响下,具有地表、地下的“复合临空面”的“复合应力场”中“复合变动”的“复合机理”;并提出这种山体侧向变动机理的典型地质模式,借以论证山体稳定性。 相似文献
12.
层状反倾岩质边坡是一种常见边坡类型，其变形破坏模式多样、力学机制复杂、影响因素众多。为揭示层状反倾岩质边坡不同临空条件几何特征参数对反倾边坡倾倒变形影响规律，通过3DEC并结合数理统计系统深入研究几何特征参数对倾倒变形影响。研究表明:①反倾边坡具有3个临空面时边坡变形最大，1个临空面时边坡变形最小；②变形随边坡高度、切坡角度增大而增大，随节理面与临空面夹角的增大而减小，随岩层厚度增大先增大后减小；③2个临空面夹角90°时边坡变形最大；④1个、2个临空面时节理倾角60°时位移最大，3个临空面时随节理倾角增大而增大。 相似文献
13.
Experimental study of motion characteristics of rock slopes with weak intercalation under seismic excitation 总被引：1，自引：0，他引：1
In order to investigate the effect of a weak intercalation on slope stability, a large-scale shaking table model test was conducted to study the dynamic response of rock slope models with weak intercalation. The dynamic response of the prototype slopes were studied in laboratory with the consideration of law of similitude. The initiation failure was observed in the rock slope model with a counter-tilt thin-weak intercalation firstly, not in the slope model with a horizontal thin-weak intercalation. Furthermore, it was interesting that the fracture site is shifted from crest top to the slope surface near the weak intercalation, which is different with the location of failure position in a normal layered slope. We also discussed the effect of the dip angle and the thickness of weak intercalation on the failure mechanism and instability mode of the layered rock slope. From the experimental result, it was noted that the stability of the slope with a counter-tilt weak intercalation could be worse than that of the other slopes under seismic excitation. The findings showed the difference of failure in slopes with a horizontal and counter weak intercalation, and implicated the further evaluation of failure of layered slopes caused by seismic loads. 相似文献
14.
基于三维向错理论模拟倾角为60°的矩形断层在转动角不同量级和形式下引起的地表形变,分析断层转动对地表形变大小及空间分布的影响。利用向-位错模型,采用数值方法模拟鲜水河断裂带断层滑动与转动引起的地表形变,并与扣除趋势项的2009~2015年的GPS实测结果进行对比。研究表明：1）转动角大小与断层向错引起的地表位移场大小呈正比关系,位移场方向不变,转动方向不同时,地表位移场方向随之改变,大小不变,且断层附近地表位移场影响较大;2）基于向-位错组合模型对鲜水河断裂带模拟结果与GPS结果在大小和方向上均具有较好的一致性;3）鲜水河断裂带表现出一定的旋转特性,存在明显的分段差异性,具有一定的转换构造样式。 相似文献
15.
Assessing the slope deformation is significant for landslide prediction. Many researchers have studied the slope displacement based on field data from the inclinometer in combination with complicated numerical analysis. They found that there was a shear zone above the slip surface, and they usually focused on the distribution of velocity and displacement within the shear zone. In this paper, two simple methods are proposed to analyze the distribution of displacement and velocity along the whole profile of a slope from the slip surface to the slope surface during slow movement. In the empirical method, the slope soil above the shear zone is assumed as a rigid body. Dual or triple piecewise fitting functions are empirically proposed for the distribution of velocity along the profile of a slope. In the analytical method, the slope soil is not assumed as a rigid body but as a deformable material. Continuous functions of the velocity and displacement along the profile of a slope are directly obtained by solving the Newton's equation of motion associated with the Bingham model. Using the two proposed methods respectively, the displacement and velocity along the slope profiles of three slopes are determined. A reasonable agreement between the measured data and the calculated results of the two proposed methods has been reached. In comparison with the empirical method, the analytical method would be more beneficial for slope deformation analysis in slope engineering, because the parameters are material constants in the analytical solution independent of time t, and the nonlinear viscosity of the soil can be considered. 相似文献
16.
Modelling the flexural buckling failure of stratified rock slopes based on the multilayer beam model
The buckling failure of stratified rock slopes intersected by a set of steep discontinuities that are approximately parallel to the slope surface is frequently encountered while constructing railways and roadways in mountainous areas. In this study, an analytical approach based on the energy equilibrium principle is presented to solve the flexural buckling stability of stratified rock slopes within the framework of multilayer beam theory. The generalized HoekBrown failure criterion is introduced to reflect the influences of slope size(scale effects) on the buckling stability. Subsequently, numerical and physical modellings from previous literatures are employed to validate the proposed approach. Furthermore, a practical case of Bawang Mountain landslide is also used for the comparative analysis. The study shows that the present analytical approach is capable to provide a more reasonable assessment for the buckling failure of stratified rock slopes, compared with several existing analytical approaches. Finally, a detailed parametric study is implemented, and the results indicate that the effects of rock strength, rock deformation modulus, geological strength index, layer thickness and disturbance degree of rock mass on the buckling failure of stratified rock slopes are more significant than that of rock type and slope angle. 相似文献
17.
《中国海洋大学学报(英文版)》2021,(5)
Marine geological disasters occurred frequently in the deep-water slope area of the northern South China Sea, especially submarine landslides, which caused serious damage to marine facilities. The cyclic elastoplastic model that can describe the cyclic stress-strain response characteristic for soft clay, is embedded into the coupled Eulerian-Lagrangian(CEL) algorithm of ABAQUS by means of subroutine interface technology. On the basis of CEL technique and undrained cyclic elastoplastic model, a method for analyzing the dynamic instability process of marine slopes under the action of earthquake load is developed. The rationality for cyclic elastoplastic constitutive model is validated by comparing its calculated results with those of von Mises model built in Abaqus. The dynamic instability process of slopes under different conditions are analyzed. The results indicate that the deformation accumulation of soft clay have a significant effect on the dynamic instability process of submarine slopes under earthquake loading. The cumulative deformation is taken into our model and this makes the calculated final deformation of the slope under earthquake load larger than the results of conventional numerical method. When different contact conditions are used for analysis, the smaller the friction coefficient is, the larger the deformation of slopes will be. A numerical analysis method that can both reflect the dynamic properties of soft clay and display the dynamic instability process of submarine landslide is proposed, which could visually predict the topographies of the previous and post failure for submarine slope. 相似文献
18.
19.
Slope reinforcement for housing in Three Gorges reservoir area 总被引：1，自引：1，他引：0
The Three Gorges Project of the Yangtze River is the largest hydropower-complex project under construction in the world. Under the largescale relocation projects, 2874 engineered slopes are formed along with the construction of new towns. In this paper, the cutting slopes are mainly soil slopes and rock slopes. Soil slopes include residual soil slopes, colluvial accumulation slopes, swelling soil slopes, and artificial earth fill slopes, etc. Rock slopes include blocky structure rock slopes, layer structure rock slopes, and clastic structure rock slopes, etc. Varied protection measures have been used for slope protection in the reservoir area including shotcrete concrete-anchor bars, frame beams, retaining walls, slope stabilizing piles, sheet-pile walls, anchorage anti-shear tunnels, flexible protection grids, and drainage, etc. Besides, slope deformation monitoring systems have been set up to monitor deformation failure and the stability state of slopes. The protection measures have guaranteed slope safety and maintained a harmony with the urban environment and surrounding landscape. 相似文献
20.
黄土高原边坡特征与破坏规律的分区研究 总被引：5，自引：1，他引：4
为了研究黄土高原自然边坡的特征及破坏规律,按山系与水系或水系的分水岭、地貌单元、地层岩性特征等条件,将黄土高原划分为8个区:临洮—永靖区、天水—通渭区、兰州—会宁区、陇东区、靖边—安塞区、隰县—离石区、甘泉—吉县区和汾渭区.根据极限状态边坡的4个野外判别标准,测量了8个区510个自然极限状态黄土边坡断面,分区采用指数模型回归边坡坡高与坡宽的相关关系,计算各区20、50、100m坡高的边坡稳定系数和失效概率.结果表明:黄土高原的边坡特征与破坏形式具有分区特征,且南北差异性明显.临洮—永靖区边坡坡高与坡宽呈线性关系,表明该区边坡坡度不随坡高变化,边坡稳定性受内摩擦角控制;兰州—会宁区和靖边—安塞区高坡陡,低坡缓,高坡不稳定,易发生错落式滑坡;天水—通渭区、甘泉—吉县区和汾渭区高坡缓,低坡陡,稳定性计算结果显示高坡和低坡都较为稳定,但由于地层结构和地貌的特点,高边坡易发生低速蠕变型滑坡或高速远程滑坡;陇东区边坡整体上较为稳定;隰县—离石区受黏粒含量较高的Q1地层控制,高边坡稳定性较差;50m左右坡高的黄土边坡稳定性对强度指标内聚力、内摩擦角的敏感度都高,易于失稳. 相似文献