共查询到20条相似文献，搜索用时 31 毫秒
1.
The E24 profile slope analyzed belongs to a series of excavated slopes of the Haizhou Opencast Coal Mine. It seems to be divided into Downslope Part and Upslope Part. Its profile comprises two noticeable coal seams, called the 8# and 9# weak layers, considered as the potential failure surfaces. In consideration of the actual configuration as in the perspective of any modification, assessing the stability of this slope with various profile forms under given conditions, and assessing the risk of instability and quantifying the influence of earthworks or other modifications to the stability of this slope, have constituted the primordial objectives carried out. From assumed potential failure surfaces, any specific profiles and specified slip surfaces are defined. A factor of safety (FoS) is computed for each specified slip surface; the smallest FoS found corresponds to the least favorable slip surface. The safety factor values obtained are compared to the suggested safety factor. Limit equilibrium methods of vertical slices implemented in Slope/W, computer program for slope stability analyses, have been adopted to perform the E24 slope stability analysis. The safety factor values computed with 9# weak layer are lower than for 8#; the factors of safety obtained with Sarma's method are the smallest; more, without groundwater (long term) overall values are greater than those determined under groundwater condition (short term). The lowest safety factor value is found for a profile depending on an adopted earthwork sequence. The E24 profile slope stability analysis shows the instability risk for the deepest weak layer, and also shows the short and long term stability of this slope for the envisaged earth movements. However it demonstrates the existence of instability risk for any earthwork firstly affecting the downslope part. 相似文献
2.
A method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes 总被引：1，自引：0，他引：1
This paper describes a precise method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes. In this method, the direction of the critical slip surface at any point in a slope is determined using the Coulomb’s strength principle and the extremum principle based on the ratio of the shear strength to the shear stress at that point. The ratio, which is considered as an analysis index, can be computed once the stress field of the soil slope is obtained. The critical slip direction at any point in the slope must be the tangential direction of a potential slip surface passing through the point. Therefore, starting from a point on the top of the slope surface or on the horizontal segment outside the slope toe, the increment with a small distance into the slope is used to choose another point and the corresponding slip direction at the point is computed. Connecting all the points used in the computation forms a potential slip surface exiting at the starting point. Then the factor of safety for any potential slip surface can be computed using limit equilibrium method like Spencer method. After factors of safety for all the potential slip surfaces are obtained, the minimum one is the factor of safety for the slope and the corresponding potential slip surface is the critical slip surface of the slope. The proposed method does not need to pre-assume the shape of potential slip surfaces. Thus it is suitable for any shape of slip surfaces. Moreover the method is very simple to be applied. Examples are presented in this paper to illustrate the feasibility of the proposed method programmed in ANSYS software by macro commands. 相似文献
3.
基于等分圆弧滑面的简化条件,采用土塑性极限分析理论,建立了土质边坡极限分析模型,并推导得到了土质边坡稳定系数计算公式。该方法考虑了圆弧滑面的内能耗散率作用和边坡土体自重荷载、地震惯性力及孔隙水压力所做的外功率作用,可以解决土质边坡稳定性分析问题,是一种改进的土质边坡稳定性评价极限分析方法。 相似文献
4.
TUNCAY Ergün 《山地科学学报》2018,15(1):114-129
In this study, the mechanisms of slope instabilities triggered by engineering excavations at location of a planned tunnel portal in the northwest region of Turkey were assessed, and stability of the current slopes which has impacts on safety of a settlement (village) and agricultural fields was investigated. In the first stage of the study, in order to identify the geological units and structural properties of the sedimentary rocks in the area, to clarify the mechanisms of instabilities and to characterize discontinuity and rock mass properties field works were conducted. In this content, geotechnical boreholes, geophysical explorations between the boreholes, line surveys to explore discontinuity properties, preparation of slope profiles using topographical techniques and sampling of rock blocks and discontinuity planes were performed. In the second stage, laboratory tests were carried out on the samples to determine the geomechnical properties of the slope forming materials and discontinuities. Then, back analyses of the instabilities were made to assess the responsible shear strength parameters of the geological units during failures by considering laboratory shear test results too. Based on the backanalyses of the failures, the strength properties of the slope debris were estimated, and it has been clarified that the residual shear strength properties are the factors controlling slip mechanism along the beddings. Following the stability analyses, it is understood that a further instability along the mass or bedding planes in the failed and redesigned area are not expected, if the current slope geometry is not changed. However, safety factor calculated for the slope in the debris is 1.1 which is well below the recommended value in the literature. The minimum safety factor for currently stable slopes which were cut at the eastern part of the failed area is 1.22 which is also less than that suggested in literature. Some remedial measures such as mini-pile or slope flattening are suggested after analyses to increase the factor of safety for this part below the settlement. 相似文献
5.
软硬互层结构的顺层岩质边坡破坏类型复杂、难于防治, 针对此类边坡地质灾害易发、多发的问题, 从坡面角度、岩层倾向及组合形式、节理分布等方面进行了研究。边坡物理模型试验是揭示边坡变形破坏机理的重要手段, 基于相似理论, 以重庆市万州区孙家滑坡为工程依托, 根据滑坡区地质勘探报告设计了室内边坡物理模型试验; 试验通过顶升模型箱模拟重力加载来探究顺层岩质边坡发生破坏时, 前缘坡角和软弱夹层倾角之间的关系; 结合有限元分析软件Plaxis 2D对物理模型进行了多组数值模拟试验, 以验证软硬互层顺层岩质边坡破坏机制。试验结果表明: 对于顺层岩质边坡, 当软弱夹层的倾角在22°左右, 前缘开挖坡角58°左右时, 顺层岩质边坡容易发生滑动, 滑动面为后缘节理面和软弱夹层的贯通面。因此, 顺层岩质边坡稳定性受层面和节理面密度的控制, 当边坡含多层软弱层面时, 易沿层面和后缘节理贯通面发生破坏, 随着软弱面层数增加, 边坡稳定系数逐渐降低。研究成果可以为公路开挖切坡导致的顺层岩质边坡失稳机理研究及其稳定性评价提供理论依据, 为顺层岩质边坡失稳的预测预报提供支撑。 相似文献
6.
In analyzing seismic stability of a slope with upper bound limit analysis method, the slip surface is often assumed as a log-spiral or plane slip surface. However, due to the presence of a weak layer and unfavorable geological structural surface or a bedrock interface with overlying soft strata, the preexisting slip surface of the slope may be irregular and composed of a series of planes rather than strictly log-spiral or plane shape. A computational model is developed for analyzing the seismic stability of slopes with pre-existing slip surfaces. This model is based on the upper bound limit analysis method and can consider the effect of anchor bolts. The soil or rock is deemed to follow the Mohr-Coulomb yield criterion. The slope is divided into multiple block elements along the slip surface. According to the displacement compatibility and the associated flow rule, a kinematic velocity field of the slope can be obtained computationally. The proposed model allows not only calculation of the rate of external work owing to the combined effect of self-weight and seismic loading, but also that of the energy dissipation rate caused by the slip surface, interfaces of block elements and anchorage effect of the anchors. Considering a direct relationship between the rate of external work and the energy dissipation rate, the expressions of yield acceleration and permanent displacement of anchored slopes can be derived. Finally, the validity of this proposed model is illustrated by analysis on three typical slopes. The results showed that the proposed model is more easily formulated and does not need to solve complex equations or time consuming iterations compared with previous methods based on the conditions of force equilibrium. 相似文献
7.
顺层岩质滑坡突发性强, 破坏性大, 是危害山区城镇安全的重要灾害类型之一。发育软弱夹层的顺向斜坡是顺层岩质滑坡的高发区, 区域顺层岩质滑坡易发性评价应融入软弱夹层的控滑机制和空间分布不确定性分析。以万州区铁峰乡为研究区, 在软弱夹层物质结构及空间分布详细调查的基础上, 分析了原生沉积、构造变形和表生改造作用下区内页岩和泥岩两类软弱夹层发展为滑动面的演化机理, 总结了顺层岩质滑坡的变形破坏机理。考虑软弱夹层空间分布的不确定性, 提出了软弱夹层垂向分布和有效控滑深度范围内软弱夹层控滑贡献度的计算模型。提取了软弱夹层类型和控滑贡献度等表征顺层岩质滑坡控滑结构的关键指标, 结合地形地貌、斜坡结构、水文地质及人类工程活动4类要素, 构建了顺层岩质滑坡易发性评价指标体系。针对万州区铁峰乡河谷南侧的顺向坡区段, 以斜坡为评价单元, 采用层次分析法对研究区顺层岩质滑坡开展了易发性评价。结果显示研究区内侏罗系珍珠冲组泥化夹层和自流井组页岩层是顺层岩质滑坡的主要控滑层位, 极高易发区和高易发区占比分别为9.7%和25.8%, 岩质斜坡单元下伏软弱夹层分布情况和斜坡前缘开挖情况是影响滑坡灾害易发性的主要因素, 建房和道路开挖等人类工程活动极易诱发顺层岩质滑坡灾害。与不考虑软弱夹层相关指标的易发性评价结果相比, 本文方法的结果更符合实际情况。 相似文献
8.
9.
XIEMo-wen ZHOUGuo-yun ESAKITetsuro 《中国地理科学(英文版)》2003,13(1):66-72
In this paper ,based on a new Geographic Information System(GIS) grid-based three-dimensional (3D) deterministic model and taken the slope unit as the study object ,the landslide hazard is mapped by the index of the 3D safety factor ,Compared with the one-dimensional(1D) model of infinite slope,which is now widely used for deterministic model based landslide hazard assessment in GIS,the GIS grid-based 3D model is more acceptable and is more adapt-able for three-dimensional landslide.Assuming the initial slip as the lower part of an ellipsoid ,the 3D critical slip surface in the 3D slper stability analysis is obtained by means of a minimization of the 3D safety factor using the Monte Carlo random simulation.Using a hydraulic model tool for the watershed analysis in GIS,an automatic process has been devel-oped for identifying the slope unit from digital elevation model(DEM)data,Compared with the grid-based landslide hazard mapping method ,the slope unit possesses clear topograhical meaning,so its results are more credible,All the calcula-tions are implemented by a computational program,3DSlopeGIS,in which a GIS component s used for fulfilling the GIS spatial analysis function.and all the data for the 3D slope safety factor calculation are in the from of GIS data (the vector and the grid layers).Because of all these merits of the GIS-based 3D landslide hazard mapping method,the complex algo-rithms and iteration procedures of the 3D problem can also be perfectly implemented. 相似文献
10.
以黄冈地区青石镇政府后山堆积层滑坡为例，在分析了其工程地质特征及地质结构特征的基础上，采用有限元法研究了非饱和土瞬态体积含水量及孔隙水压力的分布，采用考虑孔隙水压力的Janbu法分析计算了降雨对堆积层滑坡安全系数的影响。研究结果表明:①降雨入渗导致坡体孔隙水压力升高，滑面抗剪强度降低，安全系数也随之逐渐降低，其中在降雨前期，两侧的抗剪强度下降速率比中部快，而到了后期中部的抗剪强度下降速率明显快于两侧；②安全系数变化表现为前19 d以0.008/d的速率缓慢下降，19~30 d以0.03/d的速率缓慢下降，30 d以后下降速度降低，至36 d之后不再发生变化，其中在0~11 d两侧抗剪强度变化对滑坡整体稳定性变化的贡献比中部大，19~36 d中部抗剪强度变化对滑坡整体稳定性变化的贡献要比两侧大；③降雨入渗过程中，地下水从坡体表层和两侧流向坡体中部，负孔压区面积向中部不断压缩，中部地下水变化受到两侧及上层的制约，体积含水量及孔隙水压力变化相对滞后；④该滑坡的防治重点是做好降雨前期坡体后缘地下水截流以及前缘地下水排泄工作，同时，做好地表排水，减少降雨入渗。 相似文献
11.
用物质点强度折减法求解边坡安全系数时, 需要选择一定的失稳判据, 而采用不同的失稳判据获得的安全系数通常存在一定差异。为此, 采用物质点强度折减法对两个边坡算例进行了稳定性分析, 对比研究了文献中常用的4种边坡失稳判据(计算不收敛、特征点位移突变、塑性应变贯通及界限值判据)在计算边坡安全系数时的合理性及适用性。同时, 将Spencer极限平衡法获得的安全系数作为参考, 进一步验证了结果的合理性与准确性。结果表明: ①数值计算的收敛性不能作为边坡失稳判据; ②将特征点位移突变视为边坡失稳判据时, 获得的安全系数与极限平衡法获得的结果基本一致, 故特征点位移突变可以作为边坡失稳判据; ③塑性应变贯通和边坡最大位移随迭代时间步趋于稳定的界限值不宜单独作为边坡失稳判据。 相似文献
12.
Submarine landslides occur frequently on most continental margins. They are effective mechanisms of sediment transfer but also a geological hazard to seafloor installations. In this paper, submarine slope stability is evaluated using a 2D limit equilibrium method. Considerations of slope, sediment, and triggering force on the factor of safety (FOS) were calculated in drained and undrained (Φ=0) cases. Results show that submarine slopes are stable when the slope is <16° under static conditions and without a weak interlayer. With a weak interlayer, slopes are stable at <18° in the drained case and at <9° in the undrained case. Earthquake loading can drastically reduce the shear strength of sediment with increased pore water pressure. The slope became unstable at >13° with earthquake peak ground acceleration (PGA) of 0.5 g; whereas with a weak layer, a PGA of 0.2 g could trigger instability at slopes >10°, and >3° for PGA of 0.5 g. The northern slope of the South China Sea is geomorphologically stable under static conditions. However, because of the possibility of high PGA at the eastern margin of the South China Sea, submarine slides are likely on the Taiwan Bank slope and eastern part of the Dongsha slope. Therefore, submarine slides recognized in seismic profiles on the Taiwan Bank slope would be triggered by an earthquake, the most important factor for triggering submarine slides on the northern slope of the South China Sea. Considering the distribution of PGA, we consider the northern slope of the South China Sea to be stable, excluding the Taiwan Bank slope, which is tectonically active. 相似文献
13.
The stability of rock slope is often controlled by the existing discontinuous surfaces, such as discrete fractures, which are ubiquitously distributing in a geological medium. In contrast with the traditional approaches used in soil slope with a continuous assumption, the simulation methods of jointed rock slope are different from that of in soil slope. This paper presents a study on jointed rock slope stability using the proposed discontinuous approach, which considers the effects of discrete fractures. Comparing with traditional methods to model fractures in an implicit way, the presented approach provides a method to simulate fractures in an explicit way, where grids between rock matrix and fractures are independent. To complete geometric components generation and mesh partition for the model, the corresponding algorithms were devised. To evaluate the stability state of rock slope quantitatively, the strength reduction method was integrated into our analysis framework. A benchmark example was used to verify the validation of the approach. A jointed rock slope, which contains natural fractures, was selected as a case study and was simulated regarding the workflow of our framework. It was set up in the light of the geological condition of the site. Slope stability was evaluated under different loading conditions with various fracture patterns. Numerical results show that fractures have significant contributions to slope stability, and different fracture patterns would lead to different shapes of the slip surface. The devised method has the ability to calculate a non-circular slip surface, which is different from a circular slip surface obtained by classical methods. 相似文献
14.
含优势渗流层边坡在降雨入渗的作用下其渗流场往往具有较高的不确定性,这给边坡的稳定性评价带来困难,通常采用概率的方法解决此类问题。针对含优势渗流层边坡降雨入渗下的可靠度问题,通过将应力分析中的点估计-有限元法引入到边坡渗流-稳定性分析,提出了考虑优势渗流层渗透特性不确定性的渗流概率分析和边坡可靠度分析方法;其次以广西某含碎石夹层土坡为例,分析了降雨入渗下碎石夹层的优势渗流效应及渗流概率,并基于此开展了该边坡降雨入渗下的可靠度分析。结果表明:①含优势渗流层边坡雨水沿优势渗流层渗入坡体内部的深度显著高于沿坡面渗入的深度;优势渗流层渗透特性的不确定性对渗流结果的影响较大,使得边坡稳定性分析具有较强的不确定性;②随着雨水入渗持时的增加,含优势渗流层边坡不同滑动面的失效概率总体呈现增加趋势,最危险滑动面的位置不断向边坡下部演化;依托工程滑动面位置的预测结果与工程实际吻合;③提出的概率分析方法适用于分析含优势渗流层边坡降雨入渗影响下的稳定性问题,而且具有计算量小的优势,可作这类边坡可靠度分析的一种新方法。 相似文献
15.
Experimental study of motion characteristics of rock slopes with weak intercalation under seismic excitation 总被引：1，自引：0，他引：1
In order to investigate the effect of a weak intercalation on slope stability, a large-scale shaking table model test was conducted to study the dynamic response of rock slope models with weak intercalation. The dynamic response of the prototype slopes were studied in laboratory with the consideration of law of similitude. The initiation failure was observed in the rock slope model with a counter-tilt thin-weak intercalation firstly, not in the slope model with a horizontal thin-weak intercalation. Furthermore, it was interesting that the fracture site is shifted from crest top to the slope surface near the weak intercalation, which is different with the location of failure position in a normal layered slope. We also discussed the effect of the dip angle and the thickness of weak intercalation on the failure mechanism and instability mode of the layered rock slope. From the experimental result, it was noted that the stability of the slope with a counter-tilt weak intercalation could be worse than that of the other slopes under seismic excitation. The findings showed the difference of failure in slopes with a horizontal and counter weak intercalation, and implicated the further evaluation of failure of layered slopes caused by seismic loads. 相似文献
16.
在持续降雨或开挖卸荷作用下, 土体的强度指标会发生劣化, 但现今采用的边坡稳定性计算大多直接将其视为一个常数。为接近真实的边坡失稳破坏模式, 基于瑞典条分法以及一阶线性应变软化机制, 提出了一种边坡渐进破坏分析新方法, 推导出应变软化型边坡极限平衡表达式, 并获得了各破坏进度下边坡的安全系数。通过对模拟算例进行分析, 证明了条分-软化法的可靠性, 且计算结果表明渐进破坏过程中安全系数不仅取决于边坡的破坏方式与强度参数, 还与岩土体的软化模量密切相关。同时, 通过与滑坡实际案例的对比验算, 证实其强度指标存在不同的衰减系数, 即黏聚力的衰减系数大于摩擦角。从理论到应用, 最终获得的条分-软化法, 不仅考虑了岩土体的强度劣化效应以及滑动面的渐进发展, 还能有效地服务于实际工程背景下边坡的稳定性分析, 可以为滑坡的预防与治理提供指导建议。 相似文献
17.
Vegetation in slopes can effectively improve slope stability.However,it is difficult to estimate the effects of vegetation on slope stability because of variations in plant species and environmental conditions.Moreover,influences of plant growth on slope stability change with time,resulting in changes in the safety factor.This study was conducted to evaluate the stability of vegetated slopes with time and investigate the effects of different layouts of plant species on slope stability.Here,we used a plant growth model and slope stability analysis to build an evaluation model.To accomplish this,one species of tree,shrub and grass was chosen to set six layout patterns.A slope with no vegetation served as a control.The safety factors of the seven slopes were then calculated using the developed evaluation model and differences in the safety factors of slopes were compared and discussed.The slope vegetated with Platycladus orientalis reached the most stable state at the age of 60 years.Shrub slope(Vitex negundo)had the maximum safety factor after 20 years.Overall,the safety factor of vegetated slopes increased from 12.1%to 49.6% compared to the slope with no vegetation.When wind force was considered,the safety factor value of the slope changed from 3.5%to 43.5%.Vegetation mixtures of trees and grasses resulted in the best slope stability.Planting grasses on slopes can improve slope stability of trees to a greater degree than that of slopes with shrubs in the early stage of growth. 相似文献
18.
A new approach to plane failure of rock slope stability based on water flow velocity in discontinuities for the Latian dam reservoir landslide 总被引：2，自引：2，他引：0
The stability of slopes is always of great concern in the field of rock engineering. The geometry and orientation of pre-existing
discontinuities show a larger impact on the behavior of slopes that is often used to describe the measurement of the steepness,
incline, gradient, or grade of a straight line. One of the structurally controlled modes of failure in jointed rock slopes
is plane failure. There are numerous analytical methods for the rock slope stability including limit equilibrium, stress analysis
and stereographic methods. The limiting equilibrium methods for slopes under various conditions against plane failure have
been previously proposed by several investigators. However, these methods do not involve water pressure on sliding surfaces
assessments due to water velocity and have not yet been validated by case study results. This paper has tried to explore the
effects of forces due to water pressure on discontinuity surfaces in plane failure through applying the improved equations.
It has studied the effect of water flow velocity on sliding surfaces in safety factor, as well. New equations for considering
water velocity (fluid dynamics) are presented. To check the validity of the suggested equations, safety factor for a case
study has been determined. Results show that velocity of water flow had significant effect on the amount of safety factor.
Also, the suggested equations have higher validity rate compared to the current equations. 相似文献
19.
土质边坡空间临界滑动面搜索的优化算法 总被引：3，自引：0，他引：3
将二维均质土坡作为平面应变问题,假定滑动面是一个圆弧,将滑弧圆心与半径转变为后缘剪入点、坡脚剪出点和过后缘点滑弧切线与x轴的交点等3个点的横坐标,然后以这3个参数为变量,给定合理的取值区间,应用黄金分割法搜索二维边坡的最小稳定系数及相应的临界滑动面。进一步假定均质土坡的三维空间滑动面为一旋转椭球体,旋转椭球体的竖向中轴面和二维的圆弧面一致,给定椭球体不同的水平轴半径值,采用以上二维滑动面搜索方法可求出不同水平半径所对应的三维最小稳定系数及相应的椭球面。结果表明:边坡的三维稳定系数没有极小值,但有极限值;对于横向延伸长的无限边坡,三维稳定系数逼近二维稳定系数,当旋转椭球长轴与短轴之比大于3时,二者很接近,边坡稳定性可简化为二维来分析;对于受地形、地下水等条件约束的短边坡,三维效应明显,在考虑实际边界条件的情况下按三维来分析。 相似文献
20.
使用双参数折减方法分析边坡稳定性的研究较多, 如何把两个折减系数定义为单一的综合安全系数是目前研究的一项重要内容。Isakov提出的最短折减路径法能够保证在不同工况下得到最小安全系数, 但是该方法的缺点在于计算复杂, 不适合工程应用。通过有限元数值模拟, 利用最短折减路径方法计算不同强度黏土构成的不同坡度均质土坡的最小安全系数和对应的折减系数, 探索了最小安全系数与土的初始黏聚力、内摩擦角以及边坡坡度的关系, 分析了初始强度对折减系数的影响。结果表明, 相同坡度下不同强度的黏土边坡在失稳时, 最小安全系数对应的临界破坏强度相同。临界破坏强度与坡度近似成线性正相关关系。由此基于最短折减路径法提出了一种新的计算最小安全系数的方法, 该方法得到的安全系数与目前常用的极限平衡方法所得结果相近, 并且计算简单, 因此可以用于边坡稳定性分析。 相似文献