Effectiveness of Mg–Al-layered double hydroxide for heavy metal removal from mine wastewater and sludge volume reduction     

M. Tamzid Rahman  T. Kameda  S. Kumagai  T. Yoshioka 《International Journal of Environmental Science and Technology》2018,15(2):263-272

Health hazards from heavy metal pollution in water systems are a global environmental problem. Of similar concern is sludge that results from wastewater treatment due to unsatisfactory sludge management technology. Therefore, the effectiveness of using Mg–Al-layered double hydroxide in the removal of heavy metals from mine wastewater was tested and compared with that of calcium hydroxide [Ca(OH)₂], which is a common treatment method for heavy metal removal. Initially, the mine wastewater contained cations of the heavy metals iron (Fe), zinc (Zn), copper (Cu), and lead (Pb). The Mg–Al-layered double hydroxides were able to remove 371, 7.2, 121, and 0.4 mg/L of these pollutants, respectively, using the co-precipitation method. The removal of these metals is most effective using 0.5 g Mg–Al-layered double hydroxide (Mg/Al molar ratio 4) and 20 min of shaking. Zn was removed by the formation of Zn(NO₃)(OH)·H₂O and Zn₅(NO₃)₂(OH)₈ when LDH, Mg/Al molar ratios of 4 and 2, respectively, were used. Similarly, Fe, Cu, and Pb were removed by the formation of Fe–Al-layered double hydroxide, Cu₂(OH)₃·NO₃ and Pb₄(OH)₄(NO₃)₄, respectively. While Ca(OH)₂ is also capable of reducing the heavy metal concentrations below the Japanese recommended values, this analysis shows that using 0.5 g Mg–Al-layered double hydroxide is a better treatment condition for mine wastewater, because it generates lower sludge volumes than 0.1 g of Ca(OH)₂. The measured sludge volume was 1.5 mL for Mg–Al-layered double hydroxide and 2.5 mL for Ca(OH)₂, a nearly twofold further reduction.  相似文献   

Interactive effect of cadmium and zinc on chromium uptake in spinach grown in Vertisol of Central India     

M. L. Dotaniya  S. Rajendiran  M. Vassanda Coumar  V. D. Meena  J. K. Saha  S. Kundu  A. Kumar  A. K. Patra 《International Journal of Environmental Science and Technology》2018,15(2):441-448

A pot culture experiment was conducted to study impact and interaction of multi-metals on growth, yield and metals uptake by spinach (variety All Green). Three levels of each chromium (0, 50 and 100 mg/kg), cadmium (0, 1 and 2 mg/kg) and zinc (0, 10 and 20 mg/kg) in combinations (total treatments 3 × 3 × 3 = 27) were applied in a Vertisol (5 kg). The results showed that increasing the concentration of chromium, cadmium and zinc in soil enhanced the respective metal concentrations in spinach root and shoot. When cadmium at 2 mg/kg along with chromium at 100 mg/kg soil was applied, chromium concentration and uptake were decreased in root and shoot. Meanwhile, zinc application had no significant effect on chromium uptake and concentration in spinach biomass. From the results, it was concluded that cadmium at higher dose had an antagonistic effect over chromium. On the other hand, in chromium, cadmium and zinc combinations particularly at their higher levels, a competition among each other was found. Therefore, the findings could be used as guidelines for controlling and management of heavy metals pollution in farmland.  相似文献   

Heavy metal exposure from co-processing of hazardous wastes for cement production and associated human risk assessment     

Norazlina Ab Halim  Faradiella Mohd. Kusin  Khairul Nizam Mohamed 《International Journal of Environmental Science and Technology》2018,15(4):733-742

This study was carried out to determine the concentration of heavy metals (Cd, Ni, Pb, Cr, Ni and Zn) in ordinary Portland cement (OPC) produced from the co-processing with hazardous waste in comparison with OPC produced using natural raw materials. The results showed that the concentration of heavy metals in cement produced from natural raw material was in the order of Zn > Pb > Cr > Ni > Cu > Cd. Zn and Cd were the highest and the lowest concentrations, respectively, in cements produced from the co-processing activity. The difference between heavy metals concentrations in OPC produced with and without co-processing was found to be statistically significant. The concentration of heavy metals in the cement produced is generally factory dependent. The human risk assessment associated with the heavy metals for non-carcinogenic and carcinogenic risks has been evaluated. The calculated hazard index (HI) and total lifetime cancer risks (LCR) were lower than the acceptable threshold reference values, HI < 1 and LCR < 1 × 10^?4, respectively. Thus, it is anticipated that there is no potential of non-carcinogenic and carcinogenic risks for both adult and children. However, the findings indicated that there is a need for regulatory monitoring. The exposure pathway for both non-carcinogenic and carcinogenic risks are both in the order of ingestion > dermal > inhalation.  相似文献   

Short-term greenhouse emission lowering effect of biochars from solid organic municipal wastes     

Djaafar Rehrah  Rishipal R. Bansode  Osman Hassan  Mohamed Ahmedna 《International Journal of Environmental Science and Technology》2018,15(5):1093-1102

Qatar economy has been growing rapidly during the last two decades during which waste generation and greenhouse gas emissions increased exponentially making them among the main environmental challenges facing the country. Production of biochar from municipal solid organic wastes (SOWs) for soil application may offer a sustainable waste management strategy while improving crop productivity and sequestering carbon. This study was conducted to (1) investigate the physicochemical parameters of biochars for SOW, (2) select the best-performing biochars for soil fertility, and (3) evaluate the potential benefits of these biochars in lowering greenhouse gases (GHGs) during soil incubation. Biochars were produced from SOW at pyrolysis temperatures of 300–750 °C and residence times of 2–6 h. Biochars were characterized before use in soil incubation to select the best-performing treatment and evaluation of potential GHG-lowering effect using CO₂ emission as proxy. Here, soil–biochar mixtures (0–2%w/w) were incubated in greenhouse settings for 120 days at 10% soil moisture. Soil properties, such as pH, EC, TC, and WHC, were significantly improved after soil amendment with biochar. Two biochars produced from mixed materials at 300–500 °C for 2 h and used at 0.5–1% application rate performed the best in enhancing soil fertility parameters. A significant decrease in CO₂ emission was observed in vials with soil–biochar mixtures, especially for biochars produced at 500 °C compared the corresponding raw materials which exhibited an exponential increase in the CO₂ emission. Hence, application of biochar to agricultural soils could be beneficial for simultaneously improving soil fertility/crop productivity while sequestering carbon, thereby reducing anthropogenic emissions of GHGs.  相似文献   

Green synthesis of magnetic mesoporous silica nanocomposite and its adsorptive performance against organochlorine pesticides     

W. A. El-Said  D. M. Fouad  M. H. Ali  M. A. El-Gahami 《International Journal of Environmental Science and Technology》2018,15(8):1731-1744

Green synthesis of nanomaterials has received increasing attention as an eco-friendly technology in materials science. Here, we have used two types of extractions from green tea leaf (i.e., total extraction and tannin extraction) as reducing agents for a rapid, simple and one-step synthesis method of mesoporous silica nanoparticles/iron oxide nanocomposite based on deposition of iron oxide onto mesoporous silica nanoparticles. Mesoporous silica nanoparticles/iron oxide nanocomposite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray, vibrating sample magnetometer, N₂ adsorption and high-resolution transmission electron microscopy. Mesoporous silica nanoparticles/iron oxide nanocomposite was used as a solid adsorbent for removal of lindane pesticide from aqueous solutions. The developed system possesses the advantages of silica as core that include large surface area and advantages of iron oxide (shell) that include the capability to interact with chlorinated compounds and ability to release by using external magnetic field. UV-Vis technique was used as a simple and easy method for monitoring the removal of lindane. Effects of pH and temperature on the removal efficiency of the developed mesoporous silica nanoparticles/iron oxide nanocomposite toward lindane pesticide were also investigated. Fourier transform infrared spectroscopy, high-performance liquid chromatography and gas chromatography techniques were used to confirm the high ability of mesoporous silica nanoparticles/iron oxide nanocomposite for sensing and the capture of lindane molecules with high sorption capacity (about 99%) that could develop a new eco-friendly strategy for detection and removal of pesticide and as a promising material for water treatment.  相似文献   

Isolation of <Emphasis Type="Italic">Bacillus cereus</Emphasis> from botanical soil and subsequent biodegradation of waste engine oil     

S. Bhurgri  F. N. Talpur  S. M. Nizamani  H. I. Afridi  M. A. Surhio  Muhammad Raza Shah  C. W. Bong 《International Journal of Environmental Science and Technology》2018,15(7):1453-1466

Waste engine oil causes a vital environmental pollution when it spill during change and transportation and products of waste engine oil causes lethal effects to the living systems. Thus, abiotic and biotic approaches are being extensively used for removal of waste engine oil pollution. Therefore in present study, waste engine oil degradation was accomplished by a new bacterial culture, isolated from the soil by an enrichment technique. Morphological, biochemical and gene sequence analysis revealed that isolate was Bacillus cereus. Subsequently, biodegradation potential of B. cereus for waste engine oil was studied. Experimental variables, such as pH, substrate concentration, inoculum size, temperature and time on the biodegradation, were checked in mineral salt medium. The biodegradation efficiency of B. cereus was determined by gravimetry, UV–visible spectrophotometry and gas chromatography. In addition, waste engine oil was also characterized by GC–MS and FTIR for its major constituents, which showed total 38 components in waste engine oil, including hopanes, benzopyrene, long-chain aliphatic hydrocarbons, dibenzothiophenes, biphenyl and their derivatives. Results of successive biodegradation indicated that B. cereus was capable to degrade 1% of waste engine oil with 98.6% degradation potential at pH 7 within 20 days. Hence, B. cereus presents an innovative tool for removing the engine oil from the contaminated area.  相似文献   

Hydrogeochemical Features of Thermal Waters of South Trungbo (Central Vietnam)     

D. A. Novikov  Doan Van Tuyen  Thi Kim Van Phan  N. A. Kharitonova 《Russian Journal of Pacific Geology》2018,12(1):63-79

The results of studying the features of the hydrogeological structure and chemical and isotope composition of thermal waters from the central part of Vietnam that are characterized by intense manifestations of intrusive magmatism are presented. It is established that low–and high–thermal waters with temperature varying within 30–85°C are developed in the area under study. The value of total mineralization of the hydrotherms ranges from 0.05 to 10.05 g/dm³. It is assumed that the circulation of thermal waters that are different in temperature and chemical composition occurs at two levels. The regular change of the hydrotherm composition in the direction from mineralized chloride sodium, including with increased Ca content, to fresh sodium bicarbonate is revealed. The ratio of δ¹⁸O–δ²H isotopes indicates that the water component is based on meteoric water. In the coastal areas, there is an isotope shift towards the ocean waters, which is also confirmed by the hydrogeochemical data. The key factors for forming the chemical composition of the thermal waters in South Trungbo are their genetic type, the interaction processes in the “water–rock–gas–organic substance” system, and their equilibrium–nonequilibrium state.  相似文献   

Creep behaviour of intact and remoulded fibrous peat     

Mohan P. Acharya  Michael T. Hendry  C. Derek Martin 《Acta Geotechnica》2018,13(2):399-417

This paper presents the creep behaviour of intact and remoulded specimens of fibrous peat obtained from a field site near Anzac, Alberta, Canada. The creep behaviour was investigated by means of long-term drained and undrained triaxial tests. The development of volumetric, axial, and undrained axial strain and strain rate during drained and undrained creep tests under variable stress conditions is presented. The stress _– strain _– strain rate (p′–ε _v–\(\dot{\varepsilon }_{\text{v}}\)) relationship is found to be unique for different stress and loading durations. The p′–ε _v–\(\dot{\varepsilon }_{\text{v}}\) relationship is analysed and represented by creep isotaches. The applicability of different creep models developed for normally consolidated clay is discussed and applied to define the development of creep strain in fibrous peat under varying isotropic and deviator stresses. The secondary consolidation coefficient for evaluating the volumetric strain rate of peat is found to be applicable with some limits. The drained creep behaviour of remoulded peat specimens differs from the behaviour shown by Shelby tube specimens, whereas the undrained creep behaviour in remoulded and Shelby tube specimens is similar.  相似文献   

Investigation of the change in soil fabric during cone penetration in silt using 2D measurements     

Priscilla Paniagua  Joana Fonseca  Anders Gylland  Steinar Nordal 《Acta Geotechnica》2018,13(1):135-148

Interpretation of CPTU testing in silt is non-trivial because of the partially drained conditions that are likely to occur during penetration. A better understanding of the pore pressure generation/dissipation is needed in order to obtain reliable design parameters. Following a previous study using X-ray computed tomography (micro-CT) with volumetric digital image correlation (3D-DIC) that clearly showed the formation of distinct dilation and compression areas around the cone; the present work takes a closer look at those areas in order to link volumetric behavior to changes in soil fabric. High-resolution 2D backscattered electron images of polished thin sections prepared from frozen samples at the end of penetration are used. The images have a spatial resolution of 0.4 µm/pixel that allow a clear identification of grains and pore spaces. Image processing techniques are developed to quantify local porosity and obtain the statistical distribution of the particle orientation for the zones around the cone tip and shaft. It is shown that the formation of compaction regions is related to the ability of the grains to rearrange and align along a well-defined preferred orientation forming a more closed-fabric characterized by high anisotropy values, while zones of dilation are associated with a more open packing with grains randomly oriented and with large voids within. These observations suggested that for a saturated soil, water will move from a compressive zone to a neighboring dilative zone, creating a short drainage path. By shedding light on the link between soil fabric and drainage patterns, this study contributes toward a better understanding of the measured macro-response during CPTU tests on silt.  相似文献   

Deformation mechanism of strain localization in 2D numerical interface tests     

Huaxiang Zhu  Wan-Huan Zhou  Zhen-Yu Yin 《Acta Geotechnica》2018,13(3):557-573

Heterogeneity arises in soil subjected to interface shearing, with the strain gradually localizing into a band area. How the strain localization accumulates and develops to form the structure is crucial in explaining some significant constitutive behaviors of the soil–structural interface during shearing, for example, stress hardening, softening, and shear-dilatancy. Using DEM simulation, interface shear tests with a periodic boundary condition are performed to investigate the strain localization process in densely and loosely packed granular soils. Based on the velocity field given by grains’ translational and rotational velocities, several kinematic quantities are analyzed during the loading history to demonstrate the evolution of strain localization. Results suggest that tiny concentrations in the shear deformation have already been observed in the very early stage of the shear test. The degree of the strain localization, quantified by a proposed new indicator, α, steadily ascends during the stress-hardening regime, dramatically jumps prior to the stress peak, and stabilizes at the stress steady state. Loose specimen does not develop a steady pattern at the large strain, as the deformation pattern transforms between localized and diffused failure modes. During the stress steady state of both specimens, remarkable correlations are observed between α and the shear stress, as well as between α and the volumetric strain rate.  相似文献